ARM: dts: Add support for sbc-3xxx with cm-t3730
This adds support for CompuLab SBC-T3530, also known as cm-t3730: http://compulab.co.il/products/sbcs/sbc-t3530/ It seems that with the sbc-3xxx mainboard is also used on SBC-T3517 and SBC-T3730 with just a different CPU module: http://compulab.co.il/products/sbcs/sbc-t3517/ http://compulab.co.il/products/sbcs/sbc-t3730/ So let's add a common omap3-sb-t35.dtsi and then separate SoC specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and omap3-sbc-t3517.dts. I've tested this with SBC-T3730 as that's the only one I have. At least serial, both Ethernet controllers, MMC, and wl12xx WLAN work. Note that WLAN seems to be different for SBC-T3530. And SBC-T3517 may need some changes for the EMAC Ethernet if that's used instead of the smsc911x. Cc: devicetree@vger.kernel.org Cc: Mike Rapoport <mike@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit is contained in:
Tony Lindgren
parent
adfe9361b2
commit
0f0cfc6954
|
|
@ -179,6 +179,8 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
|
|||
omap2420-n810-wimax.dtb \
|
||||
omap3430-sdp.dtb \
|
||||
omap3-beagle.dtb \
|
||||
omap3-cm-t3730.dtb \
|
||||
omap3-sbc-t3730.dtb \
|
||||
omap3-devkit8000.dtb \
|
||||
omap3-beagle-xm.dtb \
|
||||
omap3-evm.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,104 @@
|
|||
/*
|
||||
* Support for CompuLab CM-T3730
|
||||
*/
|
||||
/dts-v1/;
|
||||
|
||||
#include "omap36xx.dtsi"
|
||||
#include "omap3-cm-t3x30.dtsi"
|
||||
|
||||
/ {
|
||||
model = "CompuLab CM-T3730";
|
||||
compatible = "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
|
||||
|
||||
wl12xx_vmmc2: wl12xx_vmmc2 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vw1271";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wl12xx_gpio>;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>; /* gpio73 */
|
||||
startup-delay-us = <20000>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
wl12xx_vaux2: wl12xx_vaux2 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vwl1271_vaux2";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
vin-supply = <&vaux2>;
|
||||
};
|
||||
};
|
||||
|
||||
&omap3_pmx_core {
|
||||
mmc1_pins: pinmux_mmc1_pins {
|
||||
pinctrl-single,pins = <
|
||||
0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
|
||||
0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
|
||||
0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
|
||||
0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
|
||||
0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
|
||||
0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
|
||||
>;
|
||||
};
|
||||
|
||||
mmc2_pins: pinmux_mmc2_pins {
|
||||
pinctrl-single,pins = <
|
||||
0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
|
||||
0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
|
||||
0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
|
||||
0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
|
||||
0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
|
||||
0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
|
||||
>;
|
||||
};
|
||||
|
||||
smsc1_pins: pinmux_smsc1_pins {
|
||||
pinctrl-single,pins = <
|
||||
0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */
|
||||
0x16a (PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */
|
||||
>;
|
||||
};
|
||||
|
||||
uart3_pins: pinmux_uart3_pins {
|
||||
pinctrl-single,pins = <
|
||||
0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
|
||||
0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
|
||||
>;
|
||||
};
|
||||
|
||||
wl12xx_gpio: pinmux_wl12xx_gpio {
|
||||
pinctrl-single,pins = <
|
||||
0xb2 (PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */
|
||||
0x134 (PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
vmmc-supply = <&vmmc1>;
|
||||
bus-width = <4>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mmc1_pins>;
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mmc2_pins>;
|
||||
vmmc-supply = <&wl12xx_vmmc2>;
|
||||
vmmc_aux-supply = <&wl12xx_vaux2>;
|
||||
non-removable;
|
||||
bus-width = <4>;
|
||||
cap-power-off-card;
|
||||
};
|
||||
|
||||
&smsc1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&smsc1_pins>;
|
||||
};
|
||||
|
||||
&uart3 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart3_pins>;
|
||||
};
|
||||
|
|
@ -0,0 +1,95 @@
|
|||
/*
|
||||
* Common support for CompuLab CM-T3530 and CM-T3730
|
||||
*/
|
||||
|
||||
/ {
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x10000000>; /* 256 MB */
|
||||
};
|
||||
|
||||
cpus {
|
||||
cpu@0 {
|
||||
cpu0-supply = <&vcc>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
ledb {
|
||||
label = "cm-t35:green";
|
||||
gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
};
|
||||
|
||||
vddvario: regulator-vddvario {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vddvario";
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vdd33a: regulator-vdd33a {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vdd33a";
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
|
||||
&gpmc {
|
||||
ranges = <5 0 0x2c000000 0x01000000>;
|
||||
|
||||
smsc1: ethernet@5,0 {
|
||||
compatible = "smsc,lan9221", "smsc,lan9115";
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
||||
reg = <5 0 0xff>;
|
||||
bank-width = <2>;
|
||||
gpmc,mux-add-data;
|
||||
gpmc,cs-on-ns = <0>;
|
||||
gpmc,cs-rd-off-ns = <186>;
|
||||
gpmc,cs-wr-off-ns = <186>;
|
||||
gpmc,adv-on-ns = <12>;
|
||||
gpmc,adv-rd-off-ns = <48>;
|
||||
gpmc,adv-wr-off-ns = <48>;
|
||||
gpmc,oe-on-ns = <54>;
|
||||
gpmc,oe-off-ns = <168>;
|
||||
gpmc,we-on-ns = <54>;
|
||||
gpmc,we-off-ns = <168>;
|
||||
gpmc,rd-cycle-ns = <186>;
|
||||
gpmc,wr-cycle-ns = <186>;
|
||||
gpmc,access-ns = <114>;
|
||||
gpmc,page-burst-access-ns = <6>;
|
||||
gpmc,bus-turnaround-ns = <12>;
|
||||
gpmc,cycle2cycle-delay-ns = <18>;
|
||||
gpmc,wr-data-mux-bus-ns = <90>;
|
||||
gpmc,wr-access-ns = <186>;
|
||||
gpmc,cycle2cycle-samecsen;
|
||||
gpmc,cycle2cycle-diffcsen;
|
||||
vddvario-supply = <&vddvario>;
|
||||
vdd33a-supply = <&vdd33a>;
|
||||
reg-io-width = <4>;
|
||||
smsc,save-mac-address;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
clock-frequency = <400000>;
|
||||
|
||||
twl: twl@48 {
|
||||
reg = <0x48>;
|
||||
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
|
||||
interrupt-parent = <&intc>;
|
||||
};
|
||||
};
|
||||
|
||||
#include "twl4030.dtsi"
|
||||
#include "twl4030_omap3.dtsi"
|
||||
|
||||
&i2c3 {
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
&twl_gpio {
|
||||
ti,use-leds;
|
||||
};
|
||||
|
|
@ -0,0 +1,40 @@
|
|||
/*
|
||||
* Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
|
||||
*/
|
||||
|
||||
&gpmc {
|
||||
ranges = <4 0 0x2d000000 0x01000000>;
|
||||
|
||||
smsc2: ethernet@4,0 {
|
||||
compatible = "smsc,lan9221", "smsc,lan9115";
|
||||
interrupt-parent = <&gpio3>;
|
||||
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
|
||||
reg = <4 0 0xff>;
|
||||
bank-width = <2>;
|
||||
gpmc,mux-add-data;
|
||||
gpmc,cs-on-ns = <0>;
|
||||
gpmc,cs-rd-off-ns = <186>;
|
||||
gpmc,cs-wr-off-ns = <186>;
|
||||
gpmc,adv-on-ns = <12>;
|
||||
gpmc,adv-rd-off-ns = <48>;
|
||||
gpmc,adv-wr-off-ns = <48>;
|
||||
gpmc,oe-on-ns = <54>;
|
||||
gpmc,oe-off-ns = <168>;
|
||||
gpmc,we-on-ns = <54>;
|
||||
gpmc,we-off-ns = <168>;
|
||||
gpmc,rd-cycle-ns = <186>;
|
||||
gpmc,wr-cycle-ns = <186>;
|
||||
gpmc,access-ns = <114>;
|
||||
gpmc,page-burst-access-ns = <6>;
|
||||
gpmc,bus-turnaround-ns = <12>;
|
||||
gpmc,cycle2cycle-delay-ns = <18>;
|
||||
gpmc,wr-data-mux-bus-ns = <90>;
|
||||
gpmc,wr-access-ns = <186>;
|
||||
gpmc,cycle2cycle-samecsen;
|
||||
gpmc,cycle2cycle-diffcsen;
|
||||
vddvario-supply = <&vddvario>;
|
||||
vdd33a-supply = <&vdd33a>;
|
||||
reg-io-width = <4>;
|
||||
smsc,save-mac-address;
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,30 @@
|
|||
/*
|
||||
* Suppport for CompuLab SBC-T3730 with CM-T3730
|
||||
*/
|
||||
|
||||
#include "omap3-cm-t3730.dts"
|
||||
#include "omap3-sb-t35.dtsi"
|
||||
|
||||
/ {
|
||||
model = "CompuLab SBC-T3730 with CM-T3730";
|
||||
compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
|
||||
};
|
||||
|
||||
&gpmc {
|
||||
ranges = <5 0 0x2c000000 0x01000000>,
|
||||
<4 0 0x2d000000 0x01000000>;
|
||||
};
|
||||
|
||||
&smsc2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&smsc2_pins>;
|
||||
};
|
||||
|
||||
&omap3_pmx_core {
|
||||
smsc2_pins: pinmux_smsc2_pins {
|
||||
pinctrl-single,pins = <
|
||||
0x86 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */
|
||||
0xa2 (PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
|
@ -92,6 +92,33 @@ static void __init hsmmc2_internal_input_clk(void)
|
|||
omap_ctrl_writel(reg, OMAP343X_CONTROL_DEVCONF1);
|
||||
}
|
||||
|
||||
static int omap3_sbc_t3730_twl_callback(struct device *dev,
|
||||
unsigned gpio,
|
||||
unsigned ngpio)
|
||||
{
|
||||
int res;
|
||||
|
||||
res = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
|
||||
"wlan rst");
|
||||
if (res)
|
||||
return res;
|
||||
|
||||
gpio_export(gpio, 0);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void __init omap3_sbc_t3730_twl_init(void)
|
||||
{
|
||||
twl_gpio_auxdata.setup = omap3_sbc_t3730_twl_callback;
|
||||
}
|
||||
|
||||
static void __init omap3_sbc_t3730_legacy_init(void)
|
||||
{
|
||||
legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 136);
|
||||
omap_ads7846_init(1, 57, 0, NULL);
|
||||
}
|
||||
|
||||
static void __init omap3_igep0020_legacy_init(void)
|
||||
{
|
||||
omap3_igep2_display_init_of();
|
||||
|
|
@ -199,6 +226,9 @@ static struct pdata_init auxdata_quirks[] __initdata = {
|
|||
{ "nokia,n800", omap2420_n8x0_legacy_init, },
|
||||
{ "nokia,n810", omap2420_n8x0_legacy_init, },
|
||||
{ "nokia,n810-wimax", omap2420_n8x0_legacy_init, },
|
||||
#endif
|
||||
#ifdef CONFIG_ARCH_OMAP3
|
||||
{ "compulab,omap3-sbc-t3730", omap3_sbc_t3730_twl_init, },
|
||||
#endif
|
||||
{ /* sentinel */ },
|
||||
};
|
||||
|
|
@ -228,6 +258,7 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
|
|||
*/
|
||||
static struct pdata_init pdata_quirks[] __initdata = {
|
||||
#ifdef CONFIG_ARCH_OMAP3
|
||||
{ "compulab,omap3-sbc-t3730", omap3_sbc_t3730_legacy_init, },
|
||||
{ "nokia,omap3-n900", hsmmc2_internal_input_clk, },
|
||||
{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },
|
||||
{ "nokia,omap3-n950", hsmmc2_internal_input_clk, },
|
||||
|
|
|
|||
Loading…
Reference in New Issue