OpenCloudOS-Kernel/drivers/md/raid5.h

770 lines
28 KiB
C
Raw Normal View History

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
/* SPDX-License-Identifier: GPL-2.0 */
#ifndef _RAID5_H
#define _RAID5_H
#include <linux/raid/xor.h>
#include <linux/dmaengine.h>
/*
*
* Each stripe contains one buffer per device. Each buffer can be in
* one of a number of states stored in "flags". Changes between
* these states happen *almost* exclusively under the protection of the
* STRIPE_ACTIVE flag. Some very specific changes can happen in bi_end_io, and
* these are not protected by STRIPE_ACTIVE.
*
* The flag bits that are used to represent these states are:
* R5_UPTODATE and R5_LOCKED
*
* State Empty == !UPTODATE, !LOCK
* We have no data, and there is no active request
* State Want == !UPTODATE, LOCK
* A read request is being submitted for this block
* State Dirty == UPTODATE, LOCK
* Some new data is in this buffer, and it is being written out
* State Clean == UPTODATE, !LOCK
* We have valid data which is the same as on disc
*
* The possible state transitions are:
*
* Empty -> Want - on read or write to get old data for parity calc
* Empty -> Dirty - on compute_parity to satisfy write/sync request.
* Empty -> Clean - on compute_block when computing a block for failed drive
* Want -> Empty - on failed read
* Want -> Clean - on successful completion of read request
* Dirty -> Clean - on successful completion of write request
* Dirty -> Clean - on failed write
* Clean -> Dirty - on compute_parity to satisfy write/sync (RECONSTRUCT or RMW)
*
* The Want->Empty, Want->Clean, Dirty->Clean, transitions
* all happen in b_end_io at interrupt time.
* Each sets the Uptodate bit before releasing the Lock bit.
* This leaves one multi-stage transition:
* Want->Dirty->Clean
* This is safe because thinking that a Clean buffer is actually dirty
* will at worst delay some action, and the stripe will be scheduled
* for attention after the transition is complete.
*
* There is one possibility that is not covered by these states. That
* is if one drive has failed and there is a spare being rebuilt. We
* can't distinguish between a clean block that has been generated
* from parity calculations, and a clean block that has been
* successfully written to the spare ( or to parity when resyncing).
* To distinguish these states we have a stripe bit STRIPE_INSYNC that
* is set whenever a write is scheduled to the spare, or to the parity
* disc if there is no spare. A sync request clears this bit, and
* when we find it set with no buffers locked, we know the sync is
* complete.
*
* Buffers for the md device that arrive via make_request are attached
* to the appropriate stripe in one of two lists linked on b_reqnext.
* One list (bh_read) for read requests, one (bh_write) for write.
* There should never be more than one buffer on the two lists
* together, but we are not guaranteed of that so we allow for more.
*
* If a buffer is on the read list when the associated cache buffer is
* Uptodate, the data is copied into the read buffer and it's b_end_io
* routine is called. This may happen in the end_request routine only
* if the buffer has just successfully been read. end_request should
* remove the buffers from the list and then set the Uptodate bit on
* the buffer. Other threads may do this only if they first check
* that the Uptodate bit is set. Once they have checked that they may
* take buffers off the read queue.
*
* When a buffer on the write list is committed for write it is copied
* into the cache buffer, which is then marked dirty, and moved onto a
* third list, the written list (bh_written). Once both the parity
* block and the cached buffer are successfully written, any buffer on
* a written list can be returned with b_end_io.
*
* The write list and read list both act as fifos. The read list,
* write list and written list are protected by the device_lock.
* The device_lock is only for list manipulations and will only be
* held for a very short time. It can be claimed from interrupts.
*
*
* Stripes in the stripe cache can be on one of two lists (or on
* neither). The "inactive_list" contains stripes which are not
* currently being used for any request. They can freely be reused
* for another stripe. The "handle_list" contains stripes that need
* to be handled in some way. Both of these are fifo queues. Each
* stripe is also (potentially) linked to a hash bucket in the hash
* table so that it can be found by sector number. Stripes that are
* not hashed must be on the inactive_list, and will normally be at
* the front. All stripes start life this way.
*
* The inactive_list, handle_list and hash bucket lists are all protected by the
* device_lock.
* - stripes have a reference counter. If count==0, they are on a list.
* - If a stripe might need handling, STRIPE_HANDLE is set.
* - When refcount reaches zero, then if STRIPE_HANDLE it is put on
* handle_list else inactive_list
*
* This, combined with the fact that STRIPE_HANDLE is only ever
* cleared while a stripe has a non-zero count means that if the
* refcount is 0 and STRIPE_HANDLE is set, then it is on the
* handle_list and if recount is 0 and STRIPE_HANDLE is not set, then
* the stripe is on inactive_list.
*
* The possible transitions are:
* activate an unhashed/inactive stripe (get_active_stripe())
* lockdev check-hash unlink-stripe cnt++ clean-stripe hash-stripe unlockdev
* activate a hashed, possibly active stripe (get_active_stripe())
* lockdev check-hash if(!cnt++)unlink-stripe unlockdev
* attach a request to an active stripe (add_stripe_bh())
* lockdev attach-buffer unlockdev
* handle a stripe (handle_stripe())
* setSTRIPE_ACTIVE, clrSTRIPE_HANDLE ...
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
* (lockdev check-buffers unlockdev) ..
* change-state ..
* record io/ops needed clearSTRIPE_ACTIVE schedule io/ops
* release an active stripe (release_stripe())
* lockdev if (!--cnt) { if STRIPE_HANDLE, add to handle_list else add to inactive-list } unlockdev
*
* The refcount counts each thread that have activated the stripe,
* plus raid5d if it is handling it, plus one for each active request
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
* on a cached buffer, and plus one if the stripe is undergoing stripe
* operations.
*
* The stripe operations are:
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
* -copying data between the stripe cache and user application buffers
* -computing blocks to save a disk access, or to recover a missing block
* -updating the parity on a write operation (reconstruct write and
* read-modify-write)
* -checking parity correctness
* -running i/o to disk
* These operations are carried out by raid5_run_ops which uses the async_tx
* api to (optionally) offload operations to dedicated hardware engines.
* When requesting an operation handle_stripe sets the pending bit for the
* operation and increments the count. raid5_run_ops is then run whenever
* the count is non-zero.
* There are some critical dependencies between the operations that prevent some
* from being requested while another is in flight.
* 1/ Parity check operations destroy the in cache version of the parity block,
* so we prevent parity dependent operations like writes and compute_blocks
* from starting while a check is in progress. Some dma engines can perform
* the check without damaging the parity block, in these cases the parity
* block is re-marked up to date (assuming the check was successful) and is
* not re-read from disk.
* 2/ When a write operation is requested we immediately lock the affected
* blocks, and mark them as not up to date. This causes new read requests
* to be held off, as well as parity checks and compute block operations.
* 3/ Once a compute block operation has been requested handle_stripe treats
* that block as if it is up to date. raid5_run_ops guaruntees that any
* operation that is dependent on the compute block result is initiated after
* the compute block completes.
*/
/*
* Operations state - intermediate states that are visible outside of
* STRIPE_ACTIVE.
* In general _idle indicates nothing is running, _run indicates a data
* processing operation is active, and _result means the data processing result
* is stable and can be acted upon. For simple operations like biofill and
* compute that only have an _idle and _run state they are indicated with
* sh->state flags (STRIPE_BIOFILL_RUN and STRIPE_COMPUTE_RUN)
*/
/**
* enum check_states - handles syncing / repairing a stripe
* @check_state_idle - check operations are quiesced
* @check_state_run - check operation is running
* @check_state_result - set outside lock when check result is valid
* @check_state_compute_run - check failed and we are repairing
* @check_state_compute_result - set outside lock when compute result is valid
*/
enum check_states {
check_state_idle = 0,
check_state_run, /* xor parity check */
check_state_run_q, /* q-parity check */
check_state_run_pq, /* pq dual parity check */
check_state_check_result,
check_state_compute_run, /* parity repair */
check_state_compute_result,
};
/**
* enum reconstruct_states - handles writing or expanding a stripe
*/
enum reconstruct_states {
reconstruct_state_idle = 0,
reconstruct_state_prexor_drain_run, /* prexor-write */
reconstruct_state_drain_run, /* write */
reconstruct_state_run, /* expand */
reconstruct_state_prexor_drain_result,
reconstruct_state_drain_result,
reconstruct_state_result,
};
struct stripe_head {
struct hlist_node hash;
struct list_head lru; /* inactive_list or handle_list */
struct llist_node release_list;
struct r5conf *raid_conf;
short generation; /* increments with every
* reshape */
sector_t sector; /* sector of this row */
short pd_idx; /* parity disk index */
short qd_idx; /* 'Q' disk index for raid6 */
short ddf_layout;/* use DDF ordering to calculate Q */
raid5: relieve lock contention in get_active_stripe() get_active_stripe() is the last place we have lock contention. It has two paths. One is stripe isn't found and new stripe is allocated, the other is stripe is found. The first path basically calls __find_stripe and init_stripe. It accesses conf->generation, conf->previous_raid_disks, conf->raid_disks, conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded, conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except stripe_hashtbl and inactive_list, other fields are changed very rarely. With this patch, we split inactive_list and add new hash locks. Each free stripe belongs to a specific inactive list. Which inactive list is determined by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a lock_hash assigned. Stripe's inactive list is protected by a hash lock, which is determined by it's lock_hash too. The lock_hash is derivied from current stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl list too. The goal of the new hash locks introduced is we can only use the new locks in the first path of get_active_stripe(). Since we have several hash locks, lock contention is relieved significantly. The first path of get_active_stripe() accesses other fields, since they are changed rarely, changing them now need take conf->device_lock and all hash locks. For a slow path, this isn't a problem. If we need lock device_lock and hash lock, we always lock hash lock first. The tricky part is release_stripe and friends. We need take device_lock first. Neil's suggestion is we put inactive stripes to a temporary list and readd it to inactive_list after device_lock is released. In this way, we add stripes to temporary list with device_lock hold and remove stripes from the list with hash lock hold. So we don't allow concurrent access to the temporary list, which means we need allocate temporary list for all participants of release_stripe. One downside is free stripes are maintained in their inactive list, they can't across between the lists. By default, we have total 256 stripes and 8 lists, so each list will have 32 stripes. It's possible one list has free stripe but other list hasn't. The chance should be rare because stripes allocation are even distributed. And we can always allocate more stripes for cache, several mega bytes memory isn't a big deal. This completely removes the lock contention of the first path of get_active_stripe(). It slows down the second code path a little bit though because we now need takes two locks, but since the hash lock isn't contended, the overhead should be quite small (several atomic instructions). The second path of get_active_stripe() (basically sequential write or big request size randwrite) still has lock contentions. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-11-14 12:16:17 +08:00
short hash_lock_index;
unsigned long state; /* state flags */
atomic_t count; /* nr of active thread/requests */
int bm_seq; /* sequence number for bitmap flushes */
int disks; /* disks in stripe */
int overwrite_disks; /* total overwrite disks in stripe,
* this is only checked when stripe
* has STRIPE_BATCH_READY
*/
enum check_states check_state;
enum reconstruct_states reconstruct_state;
spinlock_t stripe_lock;
raid5: offload stripe handle to workqueue This is another attempt to create multiple threads to handle raid5 stripes. This time I use workqueue. raid5 handles request (especially write) in stripe unit. A stripe is page size aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a state machine for the corresponding stripe, which includes reading some disks of the stripe, calculating parity, and writing some disks of the stripe. The state machine is running in raid5d thread currently. Since there is only one thread, it doesn't scale well for high speed storage. An obvious solution is multi-threading. To get better performance, we have some requirements: a. locality. stripe corresponding to request submitted from one cpu is better handled in thread in local cpu or local node. local cpu is preferred but some times could be a bottleneck, for example, parity calculation is too heavy. local node running has wide adaptability. b. configurablity. Different setup of raid5 array might need diffent configuration. Especially the thread number. More threads don't always mean better performance because of lock contentions. My original implementation is creating some kernel threads. There are interfaces to control which cpu's stripe each thread should handle. And userspace can set affinity of the threads. This provides biggest flexibility and configurability. But it's hard to use and apparently a new thread pool implementation is disfavor. Recent workqueue improvement is quite promising. unbound workqueue will be bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to do affinity setting. For example, we can only include one HT sibling in affinity. Since work is non-reentrant by default, and we can control running thread number by limiting dispatched work_struct number. In this patch, I created several stripe worker group. A group is a numa node. stripes from cpus of one node will be added to a group list. Workqueue thread of one node will only handle stripes of worker group of the node. In this way, stripe handling has numa node locality. And as I said, we can control thread number by limiting dispatched work_struct number. The work_struct callback function handles several stripes in one run. A typical work queue usage is to run one unit in each work_struct. In raid5 case, the unit is a stripe. But we can't do that: a. Though handling a stripe doesn't need lock because of reference accounting and stripe isn't in any list, queuing a work_struct for each stripe will make workqueue lock contended very heavily. b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we might dispatch request. If each work_struct only handles one stripe, such block plug is meaningless. This implementation can't do very fine grained configuration. But the numa binding is most popular usage model, should be enough for most workloads. Note: since we have only one stripe queue, switching to multi-thread might decrease request size dispatching down to low level layer. The impact depends on thread number, raid configuration and workload. So multi-thread raid5 might not be proper for all setups. Changes V1 -> V2: 1. remove WQ_NON_REENTRANT 2. disabling multi-threading by default 3. Add more descriptions in changelog Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-28 14:30:16 +08:00
int cpu;
struct r5worker_group *group;
RAID5: batch adjacent full stripe write stripe cache is 4k size. Even adjacent full stripe writes are handled in 4k unit. Idealy we should use big size for adjacent full stripe writes. Bigger stripe cache size means less stripes runing in the state machine so can reduce cpu overhead. And also bigger size can cause bigger IO size dispatched to under layer disks. With below patch, we will automatically batch adjacent full stripe write together. Such stripes will be added to the batch list. Only the first stripe of the list will be put to handle_list and so run handle_stripe(). Some steps of handle_stripe() are extended to cover all stripes of the list, including ops_run_io, ops_run_biodrain and so on. With this patch, we have less stripes running in handle_stripe() and we send IO of whole stripe list together to increase IO size. Stripes added to a batch list have some limitations. A batch list can only include full stripe write and can't cross chunk boundary to make sure stripes have the same parity disks. Stripes in a batch list must be in the same state (no written, toread and so on). If a stripe is in a batch list, all new read/write to add_stripe_bio will be blocked to overlap conflict till the batch list is handled. The limitations will make sure stripes in a batch list be in exactly the same state in the life circly. I did test running 160k randwrite in a RAID5 array with 32k chunk size and 6 PCIe SSD. This patch improves around 30% performance and IO size to under layer disk is exactly 32k. I also run a 4k randwrite test in the same array to make sure the performance isn't changed with the patch. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2014-12-15 09:57:03 +08:00
struct stripe_head *batch_head; /* protected by stripe lock */
spinlock_t batch_lock; /* only header's lock is useful */
struct list_head batch_list; /* protected by head's batch lock*/
raid5: add basic stripe log This introduces a simple log for raid5. Data/parity writing to raid array first writes to the log, then write to raid array disks. If crash happens, we can recovery data from the log. This can speed up raid resync and fix write hole issue. The log structure is pretty simple. Data/meta data is stored in block unit, which is 4k generally. It has only one type of meta data block. The meta data block can track 3 types of data, stripe data, stripe parity and flush block. MD superblock will point to the last valid meta data block. Each meta data block has checksum/seq number, so recovery can scan the log correctly. We store a checksum of stripe data/parity to the metadata block, so meta data and stripe data/parity can be written to log disk together. otherwise, meta data write must wait till stripe data/parity is finished. For stripe data, meta data block will record stripe data sector and size. Currently the size is always 4k. This meta data record can be made simpler if we just fix write hole (eg, we can record data of a stripe's different disks together), but this format can be extended to support caching in the future, which must record data address/size. For stripe parity, meta data block will record stripe sector. It's size should be 4k (for raid5) or 8k (for raid6). We always store p parity first. This format should work for caching too. flush block indicates a stripe is in raid array disks. Fixing write hole doesn't need this type of meta data, it's for caching extension. Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-14 05:31:59 +08:00
union {
struct r5l_io_unit *log_io;
struct ppl_io_unit *ppl_io;
};
raid5: add basic stripe log This introduces a simple log for raid5. Data/parity writing to raid array first writes to the log, then write to raid array disks. If crash happens, we can recovery data from the log. This can speed up raid resync and fix write hole issue. The log structure is pretty simple. Data/meta data is stored in block unit, which is 4k generally. It has only one type of meta data block. The meta data block can track 3 types of data, stripe data, stripe parity and flush block. MD superblock will point to the last valid meta data block. Each meta data block has checksum/seq number, so recovery can scan the log correctly. We store a checksum of stripe data/parity to the metadata block, so meta data and stripe data/parity can be written to log disk together. otherwise, meta data write must wait till stripe data/parity is finished. For stripe data, meta data block will record stripe data sector and size. Currently the size is always 4k. This meta data record can be made simpler if we just fix write hole (eg, we can record data of a stripe's different disks together), but this format can be extended to support caching in the future, which must record data address/size. For stripe parity, meta data block will record stripe sector. It's size should be 4k (for raid5) or 8k (for raid6). We always store p parity first. This format should work for caching too. flush block indicates a stripe is in raid array disks. Fixing write hole doesn't need this type of meta data, it's for caching extension. Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-14 05:31:59 +08:00
struct list_head log_list;
md/r5cache: write-out phase and reclaim support There are two limited resources, stripe cache and journal disk space. For better performance, we priotize reclaim of full stripe writes. To free up more journal space, we free earliest data on the journal. In current implementation, reclaim happens when: 1. Periodically (every R5C_RECLAIM_WAKEUP_INTERVAL, 30 seconds) reclaim if there is no reclaim in the past 5 seconds. 2. when there are R5C_FULL_STRIPE_FLUSH_BATCH (256) cached full stripes, or cached stripes is enough for a full stripe (chunk size / 4k) (r5c_check_cached_full_stripe) 3. when there is pressure on stripe cache (r5c_check_stripe_cache_usage) 4. when there is pressure on journal space (r5l_write_stripe, r5c_cache_data) r5c_do_reclaim() contains new logic of reclaim. For stripe cache: When stripe cache pressure is high (more than 3/4 stripes are cached, or there is empty inactive lists), flush all full stripe. If fewer than R5C_RECLAIM_STRIPE_GROUP (NR_STRIPE_HASH_LOCKS * 2) full stripes are flushed, flush some paritial stripes. When stripe cache pressure is moderate (1/2 to 3/4 of stripes are cached), flush all full stripes. For log space: To avoid deadlock due to log space, we need to reserve enough space to flush cached data. The size of required log space depends on total number of cached stripes (stripe_in_journal_count). In current implementation, the writing-out phase automatically include pending data writes with parity writes (similar to write through case). Therefore, we need up to (conf->raid_disks + 1) pages for each cached stripe (1 page for meta data, raid_disks pages for all data and parity). r5c_log_required_to_flush_cache() calculates log space required to flush cache. In the following, we refer to the space calculated by r5c_log_required_to_flush_cache() as reclaim_required_space. Two flags are added to r5conf->cache_state: R5C_LOG_TIGHT and R5C_LOG_CRITICAL. R5C_LOG_TIGHT is set when free space on the log device is less than 3x of reclaim_required_space. R5C_LOG_CRITICAL is set when free space on the log device is less than 2x of reclaim_required_space. r5c_cache keeps all data in cache (not fully committed to RAID) in a list (stripe_in_journal_list). These stripes are in the order of their first appearance on the journal. So the log tail (last_checkpoint) should point to the journal_start of the first item in the list. When R5C_LOG_TIGHT is set, r5l_reclaim_thread starts flushing out stripes at the head of stripe_in_journal. When R5C_LOG_CRITICAL is set, the state machine only writes data that are already in the log device (in stripe_in_journal_list). This patch includes a fix to improve performance by Shaohua Li <shli@fb.com>. Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:40 +08:00
sector_t log_start; /* first meta block on the journal */
struct list_head r5c; /* for r5c_cache->stripe_in_journal */
struct page *ppl_page; /* partial parity of this stripe */
/**
* struct stripe_operations
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
* @target - STRIPE_OP_COMPUTE_BLK target
* @target2 - 2nd compute target in the raid6 case
* @zero_sum_result - P and Q verification flags
* @request - async service request flags for raid_run_ops
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
*/
struct stripe_operations {
int target, target2;
enum sum_check_flags zero_sum_result;
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
} ops;
struct r5dev {
/* rreq and rvec are used for the replacement device when
* writing data to both devices.
*/
struct bio req, rreq;
struct bio_vec vec, rvec;
struct page *page, *orig_page;
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
struct bio *toread, *read, *towrite, *written;
sector_t sector; /* sector of this page */
unsigned long flags;
raid5: add basic stripe log This introduces a simple log for raid5. Data/parity writing to raid array first writes to the log, then write to raid array disks. If crash happens, we can recovery data from the log. This can speed up raid resync and fix write hole issue. The log structure is pretty simple. Data/meta data is stored in block unit, which is 4k generally. It has only one type of meta data block. The meta data block can track 3 types of data, stripe data, stripe parity and flush block. MD superblock will point to the last valid meta data block. Each meta data block has checksum/seq number, so recovery can scan the log correctly. We store a checksum of stripe data/parity to the metadata block, so meta data and stripe data/parity can be written to log disk together. otherwise, meta data write must wait till stripe data/parity is finished. For stripe data, meta data block will record stripe data sector and size. Currently the size is always 4k. This meta data record can be made simpler if we just fix write hole (eg, we can record data of a stripe's different disks together), but this format can be extended to support caching in the future, which must record data address/size. For stripe parity, meta data block will record stripe sector. It's size should be 4k (for raid5) or 8k (for raid6). We always store p parity first. This format should work for caching too. flush block indicates a stripe is in raid array disks. Fixing write hole doesn't need this type of meta data, it's for caching extension. Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-14 05:31:59 +08:00
u32 log_checksum;
unsigned short write_hint;
} dev[1]; /* allocated with extra space depending of RAID geometry */
};
/* stripe_head_state - collects and tracks the dynamic state of a stripe_head
* for handle_stripe.
*/
struct stripe_head_state {
/* 'syncing' means that we need to read all devices, either
* to check/correct parity, or to reconstruct a missing device.
* 'replacing' means we are replacing one or more drives and
* the source is valid at this point so we don't need to
* read all devices, just the replacement targets.
*/
int syncing, expanding, expanded, replacing;
int locked, uptodate, to_read, to_write, failed, written;
int to_fill, compute, req_compute, non_overwrite;
md/r5cache: caching phase of r5cache As described in previous patch, write back cache operates in two phases: caching and writing-out. The caching phase works as: 1. write data to journal (r5c_handle_stripe_dirtying, r5c_cache_data) 2. call bio_endio (r5c_handle_data_cached, r5c_return_dev_pending_writes). Then the writing-out phase is as: 1. Mark the stripe as write-out (r5c_make_stripe_write_out) 2. Calcualte parity (reconstruct or RMW) 3. Write parity (and maybe some other data) to journal device 4. Write data and parity to RAID disks This patch implements caching phase. The cache is integrated with stripe cache of raid456. It leverages code of r5l_log to write data to journal device. Writing-out phase of the cache is implemented in the next patch. With r5cache, write operation does not wait for parity calculation and write out, so the write latency is lower (1 write to journal device vs. read and then write to raid disks). Also, r5cache will reduce RAID overhead (multipile IO due to read-modify-write of parity) and provide more opportunities of full stripe writes. This patch adds 2 flags to stripe_head.state: - STRIPE_R5C_PARTIAL_STRIPE, - STRIPE_R5C_FULL_STRIPE, Instead of inactive_list, stripes with cached data are tracked in r5conf->r5c_full_stripe_list and r5conf->r5c_partial_stripe_list. STRIPE_R5C_FULL_STRIPE and STRIPE_R5C_PARTIAL_STRIPE are flags for stripes in these lists. Note: stripes in r5c_full/partial_stripe_list are not considered as "active". For RMW, the code allocates an extra page for each data block being updated. This is stored in r5dev->orig_page and the old data is read into it. Then the prexor calculation subtracts ->orig_page from the parity block, and the reconstruct calculation adds the ->page data back into the parity block. r5cache naturally excludes SkipCopy. When the array has write back cache, async_copy_data() will not skip copy. There are some known limitations of the cache implementation: 1. Write cache only covers full page writes (R5_OVERWRITE). Writes of smaller granularity are write through. 2. Only one log io (sh->log_io) for each stripe at anytime. Later writes for the same stripe have to wait. This can be improved by moving log_io to r5dev. 3. With writeback cache, read path must enter state machine, which is a significant bottleneck for some workloads. 4. There is no per stripe checkpoint (with r5l_payload_flush) in the log, so recovery code has to replay more than necessary data (sometimes all the log from last_checkpoint). This reduces availability of the array. This patch includes a fix proposed by ZhengYuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:39 +08:00
int injournal, just_cached;
int failed_num[2];
int p_failed, q_failed;
int dec_preread_active;
unsigned long ops_request;
struct md_rdev *blocked_rdev;
int handle_bad_blocks;
int log_failed;
int waiting_extra_page;
};
/* Flags for struct r5dev.flags */
enum r5dev_flags {
R5_UPTODATE, /* page contains current data */
R5_LOCKED, /* IO has been submitted on "req" */
R5_DOUBLE_LOCKED,/* Cannot clear R5_LOCKED until 2 writes complete */
R5_OVERWRITE, /* towrite covers whole page */
/* and some that are internal to handle_stripe */
R5_Insync, /* rdev && rdev->in_sync at start */
R5_Wantread, /* want to schedule a read */
R5_Wantwrite,
R5_Overlap, /* There is a pending overlapping request
* on this block */
R5_ReadNoMerge, /* prevent bio from merging in block-layer */
R5_ReadError, /* seen a read error here recently */
R5_ReWrite, /* have tried to over-write the readerror */
R5_Expanded, /* This block now has post-expand data */
R5_Wantcompute, /* compute_block in progress treat as
* uptodate
*/
R5_Wantfill, /* dev->toread contains a bio that needs
* filling
*/
R5_Wantdrain, /* dev->towrite needs to be drained */
R5_WantFUA, /* Write should be FUA */
R5_SyncIO, /* The IO is sync */
R5_WriteError, /* got a write error - need to record it */
R5_MadeGood, /* A bad block has been fixed by writing to it */
R5_ReadRepl, /* Will/did read from replacement rather than orig */
R5_MadeGoodRepl,/* A bad block on the replacement device has been
* fixed by writing to it */
R5_NeedReplace, /* This device has a replacement which is not
* up-to-date at this stripe. */
R5_WantReplace, /* We need to update the replacement, we have read
* data in, and now is a good time to write it out.
*/
MD: raid5 trim support Discard for raid4/5/6 has limitation. If discard request size is small, we do discard for one disk, but we need calculate parity and write parity disk. To correctly calculate parity, zero_after_discard must be guaranteed. Even it's true, we need do discard for one disk but write another disks, which makes the parity disks wear out fast. This doesn't make sense. So an efficient discard for raid4/5/6 should discard all data disks and parity disks, which requires the write pattern to be (A, A+chunk_size, A+chunk_size*2...). If A's size is smaller than chunk_size, such pattern is almost impossible in practice. So in this patch, I only handle the case that A's size equals to chunk_size. That is discard request should be aligned to stripe size and its size is multiple of stripe size. Since we can only handle request with specific alignment and size (or part of the request fitting stripes), we can't guarantee zero_after_discard even zero_after_discard is true in low level drives. The block layer doesn't send down correctly aligned requests even correct discard alignment is set, so I must filter out. For raid4/5/6 parity calculation, if data is 0, parity is 0. So if zero_after_discard is true for all disks, data is consistent after discard. Otherwise, data might be lost. Let's consider a scenario: discard a stripe, write data to one disk and write parity disk. The stripe could be still inconsistent till then depending on using data from other data disks or parity disks to calculate new parity. If the disk is broken, we can't restore it. So in this patch, we only enable discard support if all disks have zero_after_discard. If discard fails in one disk, we face the similar inconsistent issue above. The patch will make discard follow the same path as normal write request. If discard fails, a resync will be scheduled to make the data consistent. This isn't good to have extra writes, but data consistency is important. If a subsequent read/write request hits raid5 cache of a discarded stripe, the discarded dev page should have zero filled, so the data is consistent. This patch will always zero dev page for discarded request stripe. This isn't optimal because discard request doesn't need such payload. Next patch will avoid it. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2012-10-11 10:49:05 +08:00
R5_Discard, /* Discard the stripe */
R5_SkipCopy, /* Don't copy data from bio to stripe cache */
md/r5cache: State machine for raid5-cache write back mode This patch adds state machine for raid5-cache. With log device, the raid456 array could operate in two different modes (r5c_journal_mode): - write-back (R5C_MODE_WRITE_BACK) - write-through (R5C_MODE_WRITE_THROUGH) Existing code of raid5-cache only has write-through mode. For write-back cache, it is necessary to extend the state machine. With write-back cache, every stripe could operate in two different phases: - caching - writing-out In caching phase, the stripe handles writes as: - write to journal - return IO In writing-out phase, the stripe behaviors as a stripe in write through mode R5C_MODE_WRITE_THROUGH. STRIPE_R5C_CACHING is added to sh->state to differentiate caching and writing-out phase. Please note: this is a "no-op" patch for raid5-cache write-through mode. The following detailed explanation is copied from the raid5-cache.c: /* * raid5 cache state machine * * With rhe RAID cache, each stripe works in two phases: * - caching phase * - writing-out phase * * These two phases are controlled by bit STRIPE_R5C_CACHING: * if STRIPE_R5C_CACHING == 0, the stripe is in writing-out phase * if STRIPE_R5C_CACHING == 1, the stripe is in caching phase * * When there is no journal, or the journal is in write-through mode, * the stripe is always in writing-out phase. * * For write-back journal, the stripe is sent to caching phase on write * (r5c_handle_stripe_dirtying). r5c_make_stripe_write_out() kicks off * the write-out phase by clearing STRIPE_R5C_CACHING. * * Stripes in caching phase do not write the raid disks. Instead, all * writes are committed from the log device. Therefore, a stripe in * caching phase handles writes as: * - write to log device * - return IO * * Stripes in writing-out phase handle writes as: * - calculate parity * - write pending data and parity to journal * - write data and parity to raid disks * - return IO for pending writes */ Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:38 +08:00
R5_InJournal, /* data being written is in the journal device.
* if R5_InJournal is set for parity pd_idx, all the
* data and parity being written are in the journal
* device
*/
R5_OrigPageUPTDODATE, /* with write back cache, we read old data into
* dev->orig_page for prexor. When this flag is
* set, orig_page contains latest data in the
* raid disk.
*/
};
/*
* Stripe state
*/
enum {
STRIPE_ACTIVE,
STRIPE_HANDLE,
STRIPE_SYNC_REQUESTED,
STRIPE_SYNCING,
STRIPE_INSYNC,
md/raid5: fix interaction of 'replace' and 'recovery'. If a device in a RAID4/5/6 is being replaced while another is being recovered, then the writes to the replacement device currently don't happen, resulting in corruption when the replacement completes and the new drive takes over. This is because the replacement writes are only triggered when 's.replacing' is set and not when the similar 's.sync' is set (which is the case during resync and recovery - it means all devices need to be read). So schedule those writes when s.replacing is set as well. In this case we cannot use "STRIPE_INSYNC" to record that the replacement has happened as that is needed for recording that any parity calculation is complete. So introduce STRIPE_REPLACED to record if the replacement has happened. For safety we should also check that STRIPE_COMPUTE_RUN is not set. This has a similar effect to the "s.locked == 0" test. The latter ensure that now IO has been flagged but not started. The former checks if any parity calculation has been flagged by not started. We must wait for both of these to complete before triggering the 'replace'. Add a similar test to the subsequent check for "are we finished yet". This possibly isn't needed (is subsumed in the STRIPE_INSYNC test), but it makes it more obvious that the REPLACE will happen before we think we are finished. Finally if a NeedReplace device is not UPTODATE then that is an error. We really must trigger a warning. This bug was introduced in commit 9a3e1101b827a59ac9036a672f5fa8d5279d0fe2 (md/raid5: detect and handle replacements during recovery.) which introduced replacement for raid5. That was in 3.3-rc3, so any stable kernel since then would benefit from this fix. Cc: stable@vger.kernel.org (3.3+) Reported-by: qindehua <13691222965@163.com> Tested-by: qindehua <qindehua@163.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-07-22 10:57:21 +08:00
STRIPE_REPLACED,
STRIPE_PREREAD_ACTIVE,
STRIPE_DELAYED,
STRIPE_DEGRADED,
STRIPE_BIT_DELAY,
STRIPE_EXPANDING,
STRIPE_EXPAND_SOURCE,
STRIPE_EXPAND_READY,
STRIPE_IO_STARTED, /* do not count towards 'bypass_count' */
STRIPE_FULL_WRITE, /* all blocks are set to be overwritten */
STRIPE_BIOFILL_RUN,
STRIPE_COMPUTE_RUN,
STRIPE_ON_UNPLUG_LIST,
md/raid5: ensure sync and DISCARD don't happen at the same time. A number of problems can occur due to races between resync/recovery and discard. - if sync_request calls handle_stripe() while a discard is happening on the stripe, it might call handle_stripe_clean_event before all of the individual discard requests have completed (so some devices are still locked, but not all). Since commit ca64cae96037de16e4af92678814f5d4bf0c1c65 md/raid5: Make sure we clear R5_Discard when discard is finished. this will cause R5_Discard to be cleared for the parity device, so handle_stripe_clean_event() will not be called when the other devices do become unlocked, so their ->written will not be cleared. This ultimately leads to a WARN_ON in init_stripe and a lock-up. - If handle_stripe_clean_event() does clear R5_UPTODATE at an awkward time for resync, it can lead to s->uptodate being less than disks in handle_parity_checks5(), which triggers a BUG (because it is one). So: - keep R5_Discard on the parity device until all other devices have completed their discard request - make sure we don't try to have a 'discard' and a 'sync' action at the same time. This involves a new stripe flag to we know when a 'discard' is happening, and the use of R5_Overlap on the parity disk so when a discard is wanted while a sync is active, so we know to wake up the discard at the appropriate time. Discard support for RAID5 was added in 3.7, so this is suitable for any -stable kernel since 3.7. Cc: stable@vger.kernel.org (v3.7+) Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com> Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-03-12 09:18:06 +08:00
STRIPE_DISCARD,
STRIPE_ON_RELEASE_LIST,
STRIPE_BATCH_READY,
STRIPE_BATCH_ERR,
STRIPE_BITMAP_PENDING, /* Being added to bitmap, don't add
* to batch yet.
*/
md/r5cache: State machine for raid5-cache write back mode This patch adds state machine for raid5-cache. With log device, the raid456 array could operate in two different modes (r5c_journal_mode): - write-back (R5C_MODE_WRITE_BACK) - write-through (R5C_MODE_WRITE_THROUGH) Existing code of raid5-cache only has write-through mode. For write-back cache, it is necessary to extend the state machine. With write-back cache, every stripe could operate in two different phases: - caching - writing-out In caching phase, the stripe handles writes as: - write to journal - return IO In writing-out phase, the stripe behaviors as a stripe in write through mode R5C_MODE_WRITE_THROUGH. STRIPE_R5C_CACHING is added to sh->state to differentiate caching and writing-out phase. Please note: this is a "no-op" patch for raid5-cache write-through mode. The following detailed explanation is copied from the raid5-cache.c: /* * raid5 cache state machine * * With rhe RAID cache, each stripe works in two phases: * - caching phase * - writing-out phase * * These two phases are controlled by bit STRIPE_R5C_CACHING: * if STRIPE_R5C_CACHING == 0, the stripe is in writing-out phase * if STRIPE_R5C_CACHING == 1, the stripe is in caching phase * * When there is no journal, or the journal is in write-through mode, * the stripe is always in writing-out phase. * * For write-back journal, the stripe is sent to caching phase on write * (r5c_handle_stripe_dirtying). r5c_make_stripe_write_out() kicks off * the write-out phase by clearing STRIPE_R5C_CACHING. * * Stripes in caching phase do not write the raid disks. Instead, all * writes are committed from the log device. Therefore, a stripe in * caching phase handles writes as: * - write to log device * - return IO * * Stripes in writing-out phase handle writes as: * - calculate parity * - write pending data and parity to journal * - write data and parity to raid disks * - return IO for pending writes */ Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:38 +08:00
STRIPE_LOG_TRAPPED, /* trapped into log (see raid5-cache.c)
* this bit is used in two scenarios:
*
* 1. write-out phase
* set in first entry of r5l_write_stripe
* clear in second entry of r5l_write_stripe
* used to bypass logic in handle_stripe
*
* 2. caching phase
* set in r5c_try_caching_write()
* clear when journal write is done
* used to initiate r5c_cache_data()
* also used to bypass logic in handle_stripe
*/
STRIPE_R5C_CACHING, /* the stripe is in caching phase
* see more detail in the raid5-cache.c
*/
md/r5cache: caching phase of r5cache As described in previous patch, write back cache operates in two phases: caching and writing-out. The caching phase works as: 1. write data to journal (r5c_handle_stripe_dirtying, r5c_cache_data) 2. call bio_endio (r5c_handle_data_cached, r5c_return_dev_pending_writes). Then the writing-out phase is as: 1. Mark the stripe as write-out (r5c_make_stripe_write_out) 2. Calcualte parity (reconstruct or RMW) 3. Write parity (and maybe some other data) to journal device 4. Write data and parity to RAID disks This patch implements caching phase. The cache is integrated with stripe cache of raid456. It leverages code of r5l_log to write data to journal device. Writing-out phase of the cache is implemented in the next patch. With r5cache, write operation does not wait for parity calculation and write out, so the write latency is lower (1 write to journal device vs. read and then write to raid disks). Also, r5cache will reduce RAID overhead (multipile IO due to read-modify-write of parity) and provide more opportunities of full stripe writes. This patch adds 2 flags to stripe_head.state: - STRIPE_R5C_PARTIAL_STRIPE, - STRIPE_R5C_FULL_STRIPE, Instead of inactive_list, stripes with cached data are tracked in r5conf->r5c_full_stripe_list and r5conf->r5c_partial_stripe_list. STRIPE_R5C_FULL_STRIPE and STRIPE_R5C_PARTIAL_STRIPE are flags for stripes in these lists. Note: stripes in r5c_full/partial_stripe_list are not considered as "active". For RMW, the code allocates an extra page for each data block being updated. This is stored in r5dev->orig_page and the old data is read into it. Then the prexor calculation subtracts ->orig_page from the parity block, and the reconstruct calculation adds the ->page data back into the parity block. r5cache naturally excludes SkipCopy. When the array has write back cache, async_copy_data() will not skip copy. There are some known limitations of the cache implementation: 1. Write cache only covers full page writes (R5_OVERWRITE). Writes of smaller granularity are write through. 2. Only one log io (sh->log_io) for each stripe at anytime. Later writes for the same stripe have to wait. This can be improved by moving log_io to r5dev. 3. With writeback cache, read path must enter state machine, which is a significant bottleneck for some workloads. 4. There is no per stripe checkpoint (with r5l_payload_flush) in the log, so recovery code has to replay more than necessary data (sometimes all the log from last_checkpoint). This reduces availability of the array. This patch includes a fix proposed by ZhengYuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:39 +08:00
STRIPE_R5C_PARTIAL_STRIPE, /* in r5c cache (to-be/being handled or
* in conf->r5c_partial_stripe_list)
*/
STRIPE_R5C_FULL_STRIPE, /* in r5c cache (to-be/being handled or
* in conf->r5c_full_stripe_list)
*/
STRIPE_R5C_PREFLUSH, /* need to flush journal device */
};
#define STRIPE_EXPAND_SYNC_FLAGS \
((1 << STRIPE_EXPAND_SOURCE) |\
(1 << STRIPE_EXPAND_READY) |\
(1 << STRIPE_EXPANDING) |\
(1 << STRIPE_SYNC_REQUESTED))
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
/*
* Operation request flags
md: raid5_run_ops - run stripe operations outside sh->lock When the raid acceleration work was proposed, Neil laid out the following attack plan: 1/ move the xor and copy operations outside spin_lock(&sh->lock) 2/ find/implement an asynchronous offload api The raid5_run_ops routine uses the asynchronous offload api (async_tx) and the stripe_operations member of a stripe_head to carry out xor+copy operations asynchronously, outside the lock. To perform operations outside the lock a new set of state flags is needed to track new requests, in-flight requests, and completed requests. In this new model handle_stripe is tasked with scanning the stripe_head for work, updating the stripe_operations structure, and finally dropping the lock and calling raid5_run_ops for processing. The following flags outline the requests that handle_stripe can make of raid5_run_ops: STRIPE_OP_BIOFILL - copy data into request buffers to satisfy a read request STRIPE_OP_COMPUTE_BLK - generate a missing block in the cache from the other blocks STRIPE_OP_PREXOR - subtract existing data as part of the read-modify-write process STRIPE_OP_BIODRAIN - copy data out of request buffers to satisfy a write request STRIPE_OP_POSTXOR - recalculate parity for new data that has entered the cache STRIPE_OP_CHECK - verify that the parity is correct STRIPE_OP_IO - submit i/o to the member disks (note this was already performed outside the stripe lock, but it made sense to add it as an operation type The flow is: 1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending 2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the operation to the async_tx api 3/ async_tx triggers the completion callback routine to set sh->ops.complete and release the stripe 4/ handle_stripe runs again to finish the operation and optionally submit new operations that were previously blocked Note this patch just defines raid5_run_ops, subsequent commits (one per major operation type) modify handle_stripe to take advantage of this routine. Changelog: * removed ops_complete_biodrain in favor of ops_complete_postxor and ops_complete_write. * removed the raid5_run_ops workqueue * call bi_end_io for reads in ops_complete_biofill, saves a call to handle_stripe * explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown * fix race between async engines and bi_end_io call for reads, Neil Brown * remove unnecessary spin_lock from ops_complete_biofill * remove test_and_set/test_and_clear BUG_ONs, Neil Brown * remove explicit interrupt handling for channel switching, this feature was absorbed (i.e. it is now implicit) by the async_tx api * use return_io in ops_complete_biofill Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-By: NeilBrown <neilb@suse.de>
2007-01-03 04:52:30 +08:00
*/
enum {
STRIPE_OP_BIOFILL,
STRIPE_OP_COMPUTE_BLK,
STRIPE_OP_PREXOR,
STRIPE_OP_BIODRAIN,
STRIPE_OP_RECONSTRUCT,
STRIPE_OP_CHECK,
STRIPE_OP_PARTIAL_PARITY,
};
md/raid5: activate raid6 rmw feature Glue it altogehter. The raid6 rmw path should work the same as the already existing raid5 logic. So emulate the prexor handling/flags and split functions as needed. 1) Enable xor_syndrome() in the async layer. 2) Split ops_run_prexor() into RAID4/5 and RAID6 logic. Xor the syndrome at the start of a rmw run as we did it before for the single parity. 3) Take care of rmw run in ops_run_reconstruct6(). Again process only the changed pages to get syndrome back into sync. 4) Enhance set_syndrome_sources() to fill NULL pages if we are in a rmw run. The lower layers will calculate start & end pages from that and call the xor_syndrome() correspondingly. 5) Adapt the several places where we ignored Q handling up to now. Performance numbers for a single E5630 system with a mix of 10 7200k desktop/server disks. 300 seconds random write with 8 threads onto a 3,2TB (10*400GB) RAID6 64K chunk without spare (group_thread_cnt=4) bsize rmw_level=1 rmw_level=0 rmw_level=1 rmw_level=0 skip_copy=1 skip_copy=1 skip_copy=0 skip_copy=0 4K 115 KB/s 141 KB/s 165 KB/s 140 KB/s 8K 225 KB/s 275 KB/s 324 KB/s 274 KB/s 16K 434 KB/s 536 KB/s 640 KB/s 534 KB/s 32K 751 KB/s 1,051 KB/s 1,234 KB/s 1,045 KB/s 64K 1,339 KB/s 1,958 KB/s 2,282 KB/s 1,962 KB/s 128K 2,673 KB/s 3,862 KB/s 4,113 KB/s 3,898 KB/s 256K 7,685 KB/s 7,539 KB/s 7,557 KB/s 7,638 KB/s 512K 19,556 KB/s 19,558 KB/s 19,652 KB/s 19,688 Kb/s Signed-off-by: Markus Stockhausen <stockhausen@collogia.de> Signed-off-by: NeilBrown <neilb@suse.de>
2014-12-15 09:57:05 +08:00
/*
* RAID parity calculation preferences
*/
enum {
PARITY_DISABLE_RMW = 0,
PARITY_ENABLE_RMW,
PARITY_PREFER_RMW,
md/raid5: activate raid6 rmw feature Glue it altogehter. The raid6 rmw path should work the same as the already existing raid5 logic. So emulate the prexor handling/flags and split functions as needed. 1) Enable xor_syndrome() in the async layer. 2) Split ops_run_prexor() into RAID4/5 and RAID6 logic. Xor the syndrome at the start of a rmw run as we did it before for the single parity. 3) Take care of rmw run in ops_run_reconstruct6(). Again process only the changed pages to get syndrome back into sync. 4) Enhance set_syndrome_sources() to fill NULL pages if we are in a rmw run. The lower layers will calculate start & end pages from that and call the xor_syndrome() correspondingly. 5) Adapt the several places where we ignored Q handling up to now. Performance numbers for a single E5630 system with a mix of 10 7200k desktop/server disks. 300 seconds random write with 8 threads onto a 3,2TB (10*400GB) RAID6 64K chunk without spare (group_thread_cnt=4) bsize rmw_level=1 rmw_level=0 rmw_level=1 rmw_level=0 skip_copy=1 skip_copy=1 skip_copy=0 skip_copy=0 4K 115 KB/s 141 KB/s 165 KB/s 140 KB/s 8K 225 KB/s 275 KB/s 324 KB/s 274 KB/s 16K 434 KB/s 536 KB/s 640 KB/s 534 KB/s 32K 751 KB/s 1,051 KB/s 1,234 KB/s 1,045 KB/s 64K 1,339 KB/s 1,958 KB/s 2,282 KB/s 1,962 KB/s 128K 2,673 KB/s 3,862 KB/s 4,113 KB/s 3,898 KB/s 256K 7,685 KB/s 7,539 KB/s 7,557 KB/s 7,638 KB/s 512K 19,556 KB/s 19,558 KB/s 19,652 KB/s 19,688 Kb/s Signed-off-by: Markus Stockhausen <stockhausen@collogia.de> Signed-off-by: NeilBrown <neilb@suse.de>
2014-12-15 09:57:05 +08:00
};
/*
* Pages requested from set_syndrome_sources()
*/
enum {
SYNDROME_SRC_ALL,
SYNDROME_SRC_WANT_DRAIN,
SYNDROME_SRC_WRITTEN,
};
/*
* Plugging:
*
* To improve write throughput, we need to delay the handling of some
* stripes until there has been a chance that several write requests
* for the one stripe have all been collected.
* In particular, any write request that would require pre-reading
* is put on a "delayed" queue until there are no stripes currently
* in a pre-read phase. Further, if the "delayed" queue is empty when
* a stripe is put on it then we "plug" the queue and do not process it
* until an unplug call is made. (the unplug_io_fn() is called).
*
* When preread is initiated on a stripe, we set PREREAD_ACTIVE and add
* it to the count of prereading stripes.
* When write is initiated, or the stripe refcnt == 0 (just in case) we
* clear the PREREAD_ACTIVE flag and decrement the count
* Whenever the 'handle' queue is empty and the device is not plugged, we
* move any strips from delayed to handle and clear the DELAYED flag and set
* PREREAD_ACTIVE.
* In stripe_handle, if we find pre-reading is necessary, we do it if
* PREREAD_ACTIVE is set, else we set DELAYED which will send it to the delayed queue.
* HANDLE gets cleared if stripe_handle leaves nothing locked.
*/
/* Note: disk_info.rdev can be set to NULL asynchronously by raid5_remove_disk.
* There are three safe ways to access disk_info.rdev.
* 1/ when holding mddev->reconfig_mutex
* 2/ when resync/recovery/reshape is known to be happening - i.e. in code that
* is called as part of performing resync/recovery/reshape.
* 3/ while holding rcu_read_lock(), use rcu_dereference to get the pointer
* and if it is non-NULL, increment rdev->nr_pending before dropping the RCU
* lock.
* When .rdev is set to NULL, the nr_pending count checked again and if
* it has been incremented, the pointer is put back in .rdev.
*/
struct disk_info {
struct md_rdev *rdev, *replacement;
struct page *extra_page; /* extra page to use in prexor */
};
/*
* Stripe cache
*/
#define NR_STRIPES 256
#define STRIPE_SIZE PAGE_SIZE
#define STRIPE_SHIFT (PAGE_SHIFT - 9)
#define STRIPE_SECTORS (STRIPE_SIZE>>9)
#define IO_THRESHOLD 1
#define BYPASS_THRESHOLD 1
#define NR_HASH (PAGE_SIZE / sizeof(struct hlist_head))
#define HASH_MASK (NR_HASH - 1)
#define MAX_STRIPE_BATCH 8
/* bio's attached to a stripe+device for I/O are linked together in bi_sector
* order without overlap. There may be several bio's per stripe+device, and
* a bio could span several devices.
* When walking this list for a particular stripe+device, we must never proceed
* beyond a bio that extends past this device, as the next bio might no longer
* be valid.
* This function is used to determine the 'next' bio in the list, given the
* sector of the current stripe+device
*/
static inline struct bio *r5_next_bio(struct bio *bio, sector_t sector)
{
int sectors = bio_sectors(bio);
if (bio->bi_iter.bi_sector + sectors < sector + STRIPE_SECTORS)
return bio->bi_next;
else
return NULL;
}
raid5: relieve lock contention in get_active_stripe() get_active_stripe() is the last place we have lock contention. It has two paths. One is stripe isn't found and new stripe is allocated, the other is stripe is found. The first path basically calls __find_stripe and init_stripe. It accesses conf->generation, conf->previous_raid_disks, conf->raid_disks, conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded, conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except stripe_hashtbl and inactive_list, other fields are changed very rarely. With this patch, we split inactive_list and add new hash locks. Each free stripe belongs to a specific inactive list. Which inactive list is determined by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a lock_hash assigned. Stripe's inactive list is protected by a hash lock, which is determined by it's lock_hash too. The lock_hash is derivied from current stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl list too. The goal of the new hash locks introduced is we can only use the new locks in the first path of get_active_stripe(). Since we have several hash locks, lock contention is relieved significantly. The first path of get_active_stripe() accesses other fields, since they are changed rarely, changing them now need take conf->device_lock and all hash locks. For a slow path, this isn't a problem. If we need lock device_lock and hash lock, we always lock hash lock first. The tricky part is release_stripe and friends. We need take device_lock first. Neil's suggestion is we put inactive stripes to a temporary list and readd it to inactive_list after device_lock is released. In this way, we add stripes to temporary list with device_lock hold and remove stripes from the list with hash lock hold. So we don't allow concurrent access to the temporary list, which means we need allocate temporary list for all participants of release_stripe. One downside is free stripes are maintained in their inactive list, they can't across between the lists. By default, we have total 256 stripes and 8 lists, so each list will have 32 stripes. It's possible one list has free stripe but other list hasn't. The chance should be rare because stripes allocation are even distributed. And we can always allocate more stripes for cache, several mega bytes memory isn't a big deal. This completely removes the lock contention of the first path of get_active_stripe(). It slows down the second code path a little bit though because we now need takes two locks, but since the hash lock isn't contended, the overhead should be quite small (several atomic instructions). The second path of get_active_stripe() (basically sequential write or big request size randwrite) still has lock contentions. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-11-14 12:16:17 +08:00
/* NOTE NR_STRIPE_HASH_LOCKS must remain below 64.
* This is because we sometimes take all the spinlocks
* and creating that much locking depth can cause
* problems.
*/
#define NR_STRIPE_HASH_LOCKS 8
#define STRIPE_HASH_LOCKS_MASK (NR_STRIPE_HASH_LOCKS - 1)
raid5: offload stripe handle to workqueue This is another attempt to create multiple threads to handle raid5 stripes. This time I use workqueue. raid5 handles request (especially write) in stripe unit. A stripe is page size aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a state machine for the corresponding stripe, which includes reading some disks of the stripe, calculating parity, and writing some disks of the stripe. The state machine is running in raid5d thread currently. Since there is only one thread, it doesn't scale well for high speed storage. An obvious solution is multi-threading. To get better performance, we have some requirements: a. locality. stripe corresponding to request submitted from one cpu is better handled in thread in local cpu or local node. local cpu is preferred but some times could be a bottleneck, for example, parity calculation is too heavy. local node running has wide adaptability. b. configurablity. Different setup of raid5 array might need diffent configuration. Especially the thread number. More threads don't always mean better performance because of lock contentions. My original implementation is creating some kernel threads. There are interfaces to control which cpu's stripe each thread should handle. And userspace can set affinity of the threads. This provides biggest flexibility and configurability. But it's hard to use and apparently a new thread pool implementation is disfavor. Recent workqueue improvement is quite promising. unbound workqueue will be bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to do affinity setting. For example, we can only include one HT sibling in affinity. Since work is non-reentrant by default, and we can control running thread number by limiting dispatched work_struct number. In this patch, I created several stripe worker group. A group is a numa node. stripes from cpus of one node will be added to a group list. Workqueue thread of one node will only handle stripes of worker group of the node. In this way, stripe handling has numa node locality. And as I said, we can control thread number by limiting dispatched work_struct number. The work_struct callback function handles several stripes in one run. A typical work queue usage is to run one unit in each work_struct. In raid5 case, the unit is a stripe. But we can't do that: a. Though handling a stripe doesn't need lock because of reference accounting and stripe isn't in any list, queuing a work_struct for each stripe will make workqueue lock contended very heavily. b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we might dispatch request. If each work_struct only handles one stripe, such block plug is meaningless. This implementation can't do very fine grained configuration. But the numa binding is most popular usage model, should be enough for most workloads. Note: since we have only one stripe queue, switching to multi-thread might decrease request size dispatching down to low level layer. The impact depends on thread number, raid configuration and workload. So multi-thread raid5 might not be proper for all setups. Changes V1 -> V2: 1. remove WQ_NON_REENTRANT 2. disabling multi-threading by default 3. Add more descriptions in changelog Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-28 14:30:16 +08:00
struct r5worker {
struct work_struct work;
struct r5worker_group *group;
raid5: relieve lock contention in get_active_stripe() get_active_stripe() is the last place we have lock contention. It has two paths. One is stripe isn't found and new stripe is allocated, the other is stripe is found. The first path basically calls __find_stripe and init_stripe. It accesses conf->generation, conf->previous_raid_disks, conf->raid_disks, conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded, conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except stripe_hashtbl and inactive_list, other fields are changed very rarely. With this patch, we split inactive_list and add new hash locks. Each free stripe belongs to a specific inactive list. Which inactive list is determined by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a lock_hash assigned. Stripe's inactive list is protected by a hash lock, which is determined by it's lock_hash too. The lock_hash is derivied from current stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl list too. The goal of the new hash locks introduced is we can only use the new locks in the first path of get_active_stripe(). Since we have several hash locks, lock contention is relieved significantly. The first path of get_active_stripe() accesses other fields, since they are changed rarely, changing them now need take conf->device_lock and all hash locks. For a slow path, this isn't a problem. If we need lock device_lock and hash lock, we always lock hash lock first. The tricky part is release_stripe and friends. We need take device_lock first. Neil's suggestion is we put inactive stripes to a temporary list and readd it to inactive_list after device_lock is released. In this way, we add stripes to temporary list with device_lock hold and remove stripes from the list with hash lock hold. So we don't allow concurrent access to the temporary list, which means we need allocate temporary list for all participants of release_stripe. One downside is free stripes are maintained in their inactive list, they can't across between the lists. By default, we have total 256 stripes and 8 lists, so each list will have 32 stripes. It's possible one list has free stripe but other list hasn't. The chance should be rare because stripes allocation are even distributed. And we can always allocate more stripes for cache, several mega bytes memory isn't a big deal. This completely removes the lock contention of the first path of get_active_stripe(). It slows down the second code path a little bit though because we now need takes two locks, but since the hash lock isn't contended, the overhead should be quite small (several atomic instructions). The second path of get_active_stripe() (basically sequential write or big request size randwrite) still has lock contentions. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-11-14 12:16:17 +08:00
struct list_head temp_inactive_list[NR_STRIPE_HASH_LOCKS];
bool working;
raid5: offload stripe handle to workqueue This is another attempt to create multiple threads to handle raid5 stripes. This time I use workqueue. raid5 handles request (especially write) in stripe unit. A stripe is page size aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a state machine for the corresponding stripe, which includes reading some disks of the stripe, calculating parity, and writing some disks of the stripe. The state machine is running in raid5d thread currently. Since there is only one thread, it doesn't scale well for high speed storage. An obvious solution is multi-threading. To get better performance, we have some requirements: a. locality. stripe corresponding to request submitted from one cpu is better handled in thread in local cpu or local node. local cpu is preferred but some times could be a bottleneck, for example, parity calculation is too heavy. local node running has wide adaptability. b. configurablity. Different setup of raid5 array might need diffent configuration. Especially the thread number. More threads don't always mean better performance because of lock contentions. My original implementation is creating some kernel threads. There are interfaces to control which cpu's stripe each thread should handle. And userspace can set affinity of the threads. This provides biggest flexibility and configurability. But it's hard to use and apparently a new thread pool implementation is disfavor. Recent workqueue improvement is quite promising. unbound workqueue will be bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to do affinity setting. For example, we can only include one HT sibling in affinity. Since work is non-reentrant by default, and we can control running thread number by limiting dispatched work_struct number. In this patch, I created several stripe worker group. A group is a numa node. stripes from cpus of one node will be added to a group list. Workqueue thread of one node will only handle stripes of worker group of the node. In this way, stripe handling has numa node locality. And as I said, we can control thread number by limiting dispatched work_struct number. The work_struct callback function handles several stripes in one run. A typical work queue usage is to run one unit in each work_struct. In raid5 case, the unit is a stripe. But we can't do that: a. Though handling a stripe doesn't need lock because of reference accounting and stripe isn't in any list, queuing a work_struct for each stripe will make workqueue lock contended very heavily. b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we might dispatch request. If each work_struct only handles one stripe, such block plug is meaningless. This implementation can't do very fine grained configuration. But the numa binding is most popular usage model, should be enough for most workloads. Note: since we have only one stripe queue, switching to multi-thread might decrease request size dispatching down to low level layer. The impact depends on thread number, raid configuration and workload. So multi-thread raid5 might not be proper for all setups. Changes V1 -> V2: 1. remove WQ_NON_REENTRANT 2. disabling multi-threading by default 3. Add more descriptions in changelog Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-28 14:30:16 +08:00
};
struct r5worker_group {
struct list_head handle_list;
struct list_head loprio_list;
raid5: offload stripe handle to workqueue This is another attempt to create multiple threads to handle raid5 stripes. This time I use workqueue. raid5 handles request (especially write) in stripe unit. A stripe is page size aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a state machine for the corresponding stripe, which includes reading some disks of the stripe, calculating parity, and writing some disks of the stripe. The state machine is running in raid5d thread currently. Since there is only one thread, it doesn't scale well for high speed storage. An obvious solution is multi-threading. To get better performance, we have some requirements: a. locality. stripe corresponding to request submitted from one cpu is better handled in thread in local cpu or local node. local cpu is preferred but some times could be a bottleneck, for example, parity calculation is too heavy. local node running has wide adaptability. b. configurablity. Different setup of raid5 array might need diffent configuration. Especially the thread number. More threads don't always mean better performance because of lock contentions. My original implementation is creating some kernel threads. There are interfaces to control which cpu's stripe each thread should handle. And userspace can set affinity of the threads. This provides biggest flexibility and configurability. But it's hard to use and apparently a new thread pool implementation is disfavor. Recent workqueue improvement is quite promising. unbound workqueue will be bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to do affinity setting. For example, we can only include one HT sibling in affinity. Since work is non-reentrant by default, and we can control running thread number by limiting dispatched work_struct number. In this patch, I created several stripe worker group. A group is a numa node. stripes from cpus of one node will be added to a group list. Workqueue thread of one node will only handle stripes of worker group of the node. In this way, stripe handling has numa node locality. And as I said, we can control thread number by limiting dispatched work_struct number. The work_struct callback function handles several stripes in one run. A typical work queue usage is to run one unit in each work_struct. In raid5 case, the unit is a stripe. But we can't do that: a. Though handling a stripe doesn't need lock because of reference accounting and stripe isn't in any list, queuing a work_struct for each stripe will make workqueue lock contended very heavily. b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we might dispatch request. If each work_struct only handles one stripe, such block plug is meaningless. This implementation can't do very fine grained configuration. But the numa binding is most popular usage model, should be enough for most workloads. Note: since we have only one stripe queue, switching to multi-thread might decrease request size dispatching down to low level layer. The impact depends on thread number, raid configuration and workload. So multi-thread raid5 might not be proper for all setups. Changes V1 -> V2: 1. remove WQ_NON_REENTRANT 2. disabling multi-threading by default 3. Add more descriptions in changelog Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-28 14:30:16 +08:00
struct r5conf *conf;
struct r5worker *workers;
int stripes_cnt;
raid5: offload stripe handle to workqueue This is another attempt to create multiple threads to handle raid5 stripes. This time I use workqueue. raid5 handles request (especially write) in stripe unit. A stripe is page size aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a state machine for the corresponding stripe, which includes reading some disks of the stripe, calculating parity, and writing some disks of the stripe. The state machine is running in raid5d thread currently. Since there is only one thread, it doesn't scale well for high speed storage. An obvious solution is multi-threading. To get better performance, we have some requirements: a. locality. stripe corresponding to request submitted from one cpu is better handled in thread in local cpu or local node. local cpu is preferred but some times could be a bottleneck, for example, parity calculation is too heavy. local node running has wide adaptability. b. configurablity. Different setup of raid5 array might need diffent configuration. Especially the thread number. More threads don't always mean better performance because of lock contentions. My original implementation is creating some kernel threads. There are interfaces to control which cpu's stripe each thread should handle. And userspace can set affinity of the threads. This provides biggest flexibility and configurability. But it's hard to use and apparently a new thread pool implementation is disfavor. Recent workqueue improvement is quite promising. unbound workqueue will be bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to do affinity setting. For example, we can only include one HT sibling in affinity. Since work is non-reentrant by default, and we can control running thread number by limiting dispatched work_struct number. In this patch, I created several stripe worker group. A group is a numa node. stripes from cpus of one node will be added to a group list. Workqueue thread of one node will only handle stripes of worker group of the node. In this way, stripe handling has numa node locality. And as I said, we can control thread number by limiting dispatched work_struct number. The work_struct callback function handles several stripes in one run. A typical work queue usage is to run one unit in each work_struct. In raid5 case, the unit is a stripe. But we can't do that: a. Though handling a stripe doesn't need lock because of reference accounting and stripe isn't in any list, queuing a work_struct for each stripe will make workqueue lock contended very heavily. b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we might dispatch request. If each work_struct only handles one stripe, such block plug is meaningless. This implementation can't do very fine grained configuration. But the numa binding is most popular usage model, should be enough for most workloads. Note: since we have only one stripe queue, switching to multi-thread might decrease request size dispatching down to low level layer. The impact depends on thread number, raid configuration and workload. So multi-thread raid5 might not be proper for all setups. Changes V1 -> V2: 1. remove WQ_NON_REENTRANT 2. disabling multi-threading by default 3. Add more descriptions in changelog Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-28 14:30:16 +08:00
};
/*
* r5c journal modes of the array: write-back or write-through.
* write-through mode has identical behavior as existing log only
* implementation.
*/
enum r5c_journal_mode {
R5C_JOURNAL_MODE_WRITE_THROUGH = 0,
R5C_JOURNAL_MODE_WRITE_BACK = 1,
};
md/r5cache: write-out phase and reclaim support There are two limited resources, stripe cache and journal disk space. For better performance, we priotize reclaim of full stripe writes. To free up more journal space, we free earliest data on the journal. In current implementation, reclaim happens when: 1. Periodically (every R5C_RECLAIM_WAKEUP_INTERVAL, 30 seconds) reclaim if there is no reclaim in the past 5 seconds. 2. when there are R5C_FULL_STRIPE_FLUSH_BATCH (256) cached full stripes, or cached stripes is enough for a full stripe (chunk size / 4k) (r5c_check_cached_full_stripe) 3. when there is pressure on stripe cache (r5c_check_stripe_cache_usage) 4. when there is pressure on journal space (r5l_write_stripe, r5c_cache_data) r5c_do_reclaim() contains new logic of reclaim. For stripe cache: When stripe cache pressure is high (more than 3/4 stripes are cached, or there is empty inactive lists), flush all full stripe. If fewer than R5C_RECLAIM_STRIPE_GROUP (NR_STRIPE_HASH_LOCKS * 2) full stripes are flushed, flush some paritial stripes. When stripe cache pressure is moderate (1/2 to 3/4 of stripes are cached), flush all full stripes. For log space: To avoid deadlock due to log space, we need to reserve enough space to flush cached data. The size of required log space depends on total number of cached stripes (stripe_in_journal_count). In current implementation, the writing-out phase automatically include pending data writes with parity writes (similar to write through case). Therefore, we need up to (conf->raid_disks + 1) pages for each cached stripe (1 page for meta data, raid_disks pages for all data and parity). r5c_log_required_to_flush_cache() calculates log space required to flush cache. In the following, we refer to the space calculated by r5c_log_required_to_flush_cache() as reclaim_required_space. Two flags are added to r5conf->cache_state: R5C_LOG_TIGHT and R5C_LOG_CRITICAL. R5C_LOG_TIGHT is set when free space on the log device is less than 3x of reclaim_required_space. R5C_LOG_CRITICAL is set when free space on the log device is less than 2x of reclaim_required_space. r5c_cache keeps all data in cache (not fully committed to RAID) in a list (stripe_in_journal_list). These stripes are in the order of their first appearance on the journal. So the log tail (last_checkpoint) should point to the journal_start of the first item in the list. When R5C_LOG_TIGHT is set, r5l_reclaim_thread starts flushing out stripes at the head of stripe_in_journal. When R5C_LOG_CRITICAL is set, the state machine only writes data that are already in the log device (in stripe_in_journal_list). This patch includes a fix to improve performance by Shaohua Li <shli@fb.com>. Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:40 +08:00
enum r5_cache_state {
R5_INACTIVE_BLOCKED, /* release of inactive stripes blocked,
* waiting for 25% to be free
*/
R5_ALLOC_MORE, /* It might help to allocate another
* stripe.
*/
R5_DID_ALLOC, /* A stripe was allocated, don't allocate
* more until at least one has been
* released. This avoids flooding
* the cache.
*/
R5C_LOG_TIGHT, /* log device space tight, need to
* prioritize stripes at last_checkpoint
*/
R5C_LOG_CRITICAL, /* log device is running out of space,
* only process stripes that are already
* occupying the log
*/
R5C_EXTRA_PAGE_IN_USE, /* a stripe is using disk_info.extra_page
* for prexor
*/
md/r5cache: write-out phase and reclaim support There are two limited resources, stripe cache and journal disk space. For better performance, we priotize reclaim of full stripe writes. To free up more journal space, we free earliest data on the journal. In current implementation, reclaim happens when: 1. Periodically (every R5C_RECLAIM_WAKEUP_INTERVAL, 30 seconds) reclaim if there is no reclaim in the past 5 seconds. 2. when there are R5C_FULL_STRIPE_FLUSH_BATCH (256) cached full stripes, or cached stripes is enough for a full stripe (chunk size / 4k) (r5c_check_cached_full_stripe) 3. when there is pressure on stripe cache (r5c_check_stripe_cache_usage) 4. when there is pressure on journal space (r5l_write_stripe, r5c_cache_data) r5c_do_reclaim() contains new logic of reclaim. For stripe cache: When stripe cache pressure is high (more than 3/4 stripes are cached, or there is empty inactive lists), flush all full stripe. If fewer than R5C_RECLAIM_STRIPE_GROUP (NR_STRIPE_HASH_LOCKS * 2) full stripes are flushed, flush some paritial stripes. When stripe cache pressure is moderate (1/2 to 3/4 of stripes are cached), flush all full stripes. For log space: To avoid deadlock due to log space, we need to reserve enough space to flush cached data. The size of required log space depends on total number of cached stripes (stripe_in_journal_count). In current implementation, the writing-out phase automatically include pending data writes with parity writes (similar to write through case). Therefore, we need up to (conf->raid_disks + 1) pages for each cached stripe (1 page for meta data, raid_disks pages for all data and parity). r5c_log_required_to_flush_cache() calculates log space required to flush cache. In the following, we refer to the space calculated by r5c_log_required_to_flush_cache() as reclaim_required_space. Two flags are added to r5conf->cache_state: R5C_LOG_TIGHT and R5C_LOG_CRITICAL. R5C_LOG_TIGHT is set when free space on the log device is less than 3x of reclaim_required_space. R5C_LOG_CRITICAL is set when free space on the log device is less than 2x of reclaim_required_space. r5c_cache keeps all data in cache (not fully committed to RAID) in a list (stripe_in_journal_list). These stripes are in the order of their first appearance on the journal. So the log tail (last_checkpoint) should point to the journal_start of the first item in the list. When R5C_LOG_TIGHT is set, r5l_reclaim_thread starts flushing out stripes at the head of stripe_in_journal. When R5C_LOG_CRITICAL is set, the state machine only writes data that are already in the log device (in stripe_in_journal_list). This patch includes a fix to improve performance by Shaohua Li <shli@fb.com>. Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:40 +08:00
};
#define PENDING_IO_MAX 512
#define PENDING_IO_ONE_FLUSH 128
struct r5pending_data {
struct list_head sibling;
sector_t sector; /* stripe sector */
struct bio_list bios;
};
struct r5conf {
struct hlist_head *stripe_hashtbl;
raid5: relieve lock contention in get_active_stripe() get_active_stripe() is the last place we have lock contention. It has two paths. One is stripe isn't found and new stripe is allocated, the other is stripe is found. The first path basically calls __find_stripe and init_stripe. It accesses conf->generation, conf->previous_raid_disks, conf->raid_disks, conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded, conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except stripe_hashtbl and inactive_list, other fields are changed very rarely. With this patch, we split inactive_list and add new hash locks. Each free stripe belongs to a specific inactive list. Which inactive list is determined by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a lock_hash assigned. Stripe's inactive list is protected by a hash lock, which is determined by it's lock_hash too. The lock_hash is derivied from current stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl list too. The goal of the new hash locks introduced is we can only use the new locks in the first path of get_active_stripe(). Since we have several hash locks, lock contention is relieved significantly. The first path of get_active_stripe() accesses other fields, since they are changed rarely, changing them now need take conf->device_lock and all hash locks. For a slow path, this isn't a problem. If we need lock device_lock and hash lock, we always lock hash lock first. The tricky part is release_stripe and friends. We need take device_lock first. Neil's suggestion is we put inactive stripes to a temporary list and readd it to inactive_list after device_lock is released. In this way, we add stripes to temporary list with device_lock hold and remove stripes from the list with hash lock hold. So we don't allow concurrent access to the temporary list, which means we need allocate temporary list for all participants of release_stripe. One downside is free stripes are maintained in their inactive list, they can't across between the lists. By default, we have total 256 stripes and 8 lists, so each list will have 32 stripes. It's possible one list has free stripe but other list hasn't. The chance should be rare because stripes allocation are even distributed. And we can always allocate more stripes for cache, several mega bytes memory isn't a big deal. This completely removes the lock contention of the first path of get_active_stripe(). It slows down the second code path a little bit though because we now need takes two locks, but since the hash lock isn't contended, the overhead should be quite small (several atomic instructions). The second path of get_active_stripe() (basically sequential write or big request size randwrite) still has lock contentions. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-11-14 12:16:17 +08:00
/* only protect corresponding hash list and inactive_list */
spinlock_t hash_locks[NR_STRIPE_HASH_LOCKS];
struct mddev *mddev;
int chunk_sectors;
md/raid5: activate raid6 rmw feature Glue it altogehter. The raid6 rmw path should work the same as the already existing raid5 logic. So emulate the prexor handling/flags and split functions as needed. 1) Enable xor_syndrome() in the async layer. 2) Split ops_run_prexor() into RAID4/5 and RAID6 logic. Xor the syndrome at the start of a rmw run as we did it before for the single parity. 3) Take care of rmw run in ops_run_reconstruct6(). Again process only the changed pages to get syndrome back into sync. 4) Enhance set_syndrome_sources() to fill NULL pages if we are in a rmw run. The lower layers will calculate start & end pages from that and call the xor_syndrome() correspondingly. 5) Adapt the several places where we ignored Q handling up to now. Performance numbers for a single E5630 system with a mix of 10 7200k desktop/server disks. 300 seconds random write with 8 threads onto a 3,2TB (10*400GB) RAID6 64K chunk without spare (group_thread_cnt=4) bsize rmw_level=1 rmw_level=0 rmw_level=1 rmw_level=0 skip_copy=1 skip_copy=1 skip_copy=0 skip_copy=0 4K 115 KB/s 141 KB/s 165 KB/s 140 KB/s 8K 225 KB/s 275 KB/s 324 KB/s 274 KB/s 16K 434 KB/s 536 KB/s 640 KB/s 534 KB/s 32K 751 KB/s 1,051 KB/s 1,234 KB/s 1,045 KB/s 64K 1,339 KB/s 1,958 KB/s 2,282 KB/s 1,962 KB/s 128K 2,673 KB/s 3,862 KB/s 4,113 KB/s 3,898 KB/s 256K 7,685 KB/s 7,539 KB/s 7,557 KB/s 7,638 KB/s 512K 19,556 KB/s 19,558 KB/s 19,652 KB/s 19,688 Kb/s Signed-off-by: Markus Stockhausen <stockhausen@collogia.de> Signed-off-by: NeilBrown <neilb@suse.de>
2014-12-15 09:57:05 +08:00
int level, algorithm, rmw_level;
int max_degraded;
int raid_disks;
int max_nr_stripes;
md/raid5: allow the stripe_cache to grow and shrink. The default setting of 256 stripe_heads is probably much too small for many configurations. So it is best to make it auto-configure. Shrinking the cache under memory pressure is easy. The only interesting part here is that we put a fairly high cost ('seeks') on shrinking the cache as the cost is greater than just having to read more data, it reduces parallelism. Growing the cache on demand needs to be done carefully. If we allow fast growth, that can upset memory balance as lots of dirty memory can quickly turn into lots of memory queued in the stripe_cache. It is important for the raid5 block device to appear congested to allow write-throttling to work. So we only add stripes slowly. We set a flag when an allocation fails because all stripes are in use, allocate at a convenient time when that flag is set, and don't allow it to be set again until at least one stripe_head has been released for re-use. This means that a spurt of requests will only cause one stripe_head to be allocated, but a steady stream of requests will slowly increase the cache size - until memory pressure puts it back again. It could take hours to reach a steady state. The value written to, and displayed in, stripe_cache_size is used as a minimum. The cache can grow above this and shrink back down to it. The actual size is not directly visible, though it can be deduced to some extent by watching stripe_cache_active. Signed-off-by: NeilBrown <neilb@suse.de>
2015-02-26 09:47:56 +08:00
int min_nr_stripes;
/* reshape_progress is the leading edge of a 'reshape'
* It has value MaxSector when no reshape is happening
* If delta_disks < 0, it is the last sector we started work on,
* else is it the next sector to work on.
*/
sector_t reshape_progress;
/* reshape_safe is the trailing edge of a reshape. We know that
* before (or after) this address, all reshape has completed.
*/
sector_t reshape_safe;
int previous_raid_disks;
int prev_chunk_sectors;
int prev_algo;
short generation; /* increments with every reshape */
seqcount_t gen_lock; /* lock against generation changes */
unsigned long reshape_checkpoint; /* Time we last updated
* metadata */
long long min_offset_diff; /* minimum difference between
* data_offset and
* new_data_offset across all
* devices. May be negative,
* but is closest to zero.
*/
struct list_head handle_list; /* stripes needing handling */
struct list_head loprio_list; /* low priority stripes */
md: introduce get_priority_stripe() to improve raid456 write performance Improve write performance by preventing the delayed_list from dumping all its stripes onto the handle_list in one shot. Delayed stripes are now further delayed by being held on the 'hold_list'. The 'hold_list' is bypassed when: * a STRIPE_IO_STARTED stripe is found at the head of 'handle_list' * 'handle_list' is empty and i/o is being done to satisfy full stripe-width write requests * 'bypass_count' is less than 'bypass_threshold'. By default the threshold is 1, i.e. every other stripe handled is a preread stripe provided the top two conditions are false. Benchmark data: System: 2x Xeon 5150, 4x SATA, mem=1GB Baseline: 2.6.24-rc7 Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048 * patched: +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512) Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS) * patched: +13% * patched + preread_bypass_threshold = 0: +37% Changes since v1: * reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and make it configurable. This defaults to fairness and modest performance gains out of the box. Changes since v2: * [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not necessary, the important change was clearing STRIPE_DELAYED in add_stripe_bio and this has been moved out to make_request for the hang fix. * [neilb@suse.de]: simplify get_priority_stripe * [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is sampled empty (+11%) * [dan.j.williams@intel.com]: decrement the bypass_count at the detection of stripes being naturally promoted off of hold_list +2%. Note, resetting bypass_count instead of decrementing on these events yields +4% but that is probably too aggressive. Changes since v3: * cosmetic fixups Tested-by: James W. Laferriere <babydr@baby-dragons.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:15:53 +08:00
struct list_head hold_list; /* preread ready stripes */
struct list_head delayed_list; /* stripes that have plugged requests */
struct list_head bitmap_list; /* stripes delaying awaiting bitmap update */
[PATCH] md: allow reads that have bypassed the cache to be retried on failure If a bypass-the-cache read fails, we simply try again through the cache. If it fails again it will trigger normal recovery precedures. update 1: From: NeilBrown <neilb@suse.de> 1/ chunk_aligned_read and retry_aligned_read assume that data_disks == raid_disks - 1 which is not true for raid6. So when an aligned read request bypasses the cache, we can get the wrong data. 2/ The cloned bio is being used-after-free in raid5_align_endio (to test BIO_UPTODATE). 3/ We forgot to add rdev->data_offset when submitting a bio for aligned-read 4/ clone_bio calls blk_recount_segments and then we change bi_bdev, so we need to invalidate the segment counts. 5/ We don't de-reference the rdev when the read completes. This means we need to record the rdev to so it is still available in the end_io routine. Fortunately bi_next in the original bio is unused at this point so we can stuff it in there. 6/ We leak a cloned bio if the target rdev is not usable. From: NeilBrown <neilb@suse.de> update 2: 1/ When aligned requests fail (read error) they need to be retried via the normal method (stripe cache). As we cannot be sure that we can process a single read in one go (we may not be able to allocate all the stripes needed) we store a bio-being-retried and a list of bioes-that-still-need-to-be-retried. When find a bio that needs to be retried, we should add it to the list, not to single-bio... 2/ We were never incrementing 'scnt' when resubmitting failed aligned requests. [akpm@osdl.org: build fix] Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 18:20:47 +08:00
struct bio *retry_read_aligned; /* currently retrying aligned bios */
unsigned int retry_read_offset; /* sector offset into retry_read_aligned */
[PATCH] md: allow reads that have bypassed the cache to be retried on failure If a bypass-the-cache read fails, we simply try again through the cache. If it fails again it will trigger normal recovery precedures. update 1: From: NeilBrown <neilb@suse.de> 1/ chunk_aligned_read and retry_aligned_read assume that data_disks == raid_disks - 1 which is not true for raid6. So when an aligned read request bypasses the cache, we can get the wrong data. 2/ The cloned bio is being used-after-free in raid5_align_endio (to test BIO_UPTODATE). 3/ We forgot to add rdev->data_offset when submitting a bio for aligned-read 4/ clone_bio calls blk_recount_segments and then we change bi_bdev, so we need to invalidate the segment counts. 5/ We don't de-reference the rdev when the read completes. This means we need to record the rdev to so it is still available in the end_io routine. Fortunately bi_next in the original bio is unused at this point so we can stuff it in there. 6/ We leak a cloned bio if the target rdev is not usable. From: NeilBrown <neilb@suse.de> update 2: 1/ When aligned requests fail (read error) they need to be retried via the normal method (stripe cache). As we cannot be sure that we can process a single read in one go (we may not be able to allocate all the stripes needed) we store a bio-being-retried and a list of bioes-that-still-need-to-be-retried. When find a bio that needs to be retried, we should add it to the list, not to single-bio... 2/ We were never incrementing 'scnt' when resubmitting failed aligned requests. [akpm@osdl.org: build fix] Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 18:20:47 +08:00
struct bio *retry_read_aligned_list; /* aligned bios retry list */
atomic_t preread_active_stripes; /* stripes with scheduled io */
[PATCH] md: allow reads that have bypassed the cache to be retried on failure If a bypass-the-cache read fails, we simply try again through the cache. If it fails again it will trigger normal recovery precedures. update 1: From: NeilBrown <neilb@suse.de> 1/ chunk_aligned_read and retry_aligned_read assume that data_disks == raid_disks - 1 which is not true for raid6. So when an aligned read request bypasses the cache, we can get the wrong data. 2/ The cloned bio is being used-after-free in raid5_align_endio (to test BIO_UPTODATE). 3/ We forgot to add rdev->data_offset when submitting a bio for aligned-read 4/ clone_bio calls blk_recount_segments and then we change bi_bdev, so we need to invalidate the segment counts. 5/ We don't de-reference the rdev when the read completes. This means we need to record the rdev to so it is still available in the end_io routine. Fortunately bi_next in the original bio is unused at this point so we can stuff it in there. 6/ We leak a cloned bio if the target rdev is not usable. From: NeilBrown <neilb@suse.de> update 2: 1/ When aligned requests fail (read error) they need to be retried via the normal method (stripe cache). As we cannot be sure that we can process a single read in one go (we may not be able to allocate all the stripes needed) we store a bio-being-retried and a list of bioes-that-still-need-to-be-retried. When find a bio that needs to be retried, we should add it to the list, not to single-bio... 2/ We were never incrementing 'scnt' when resubmitting failed aligned requests. [akpm@osdl.org: build fix] Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 18:20:47 +08:00
atomic_t active_aligned_reads;
md: introduce get_priority_stripe() to improve raid456 write performance Improve write performance by preventing the delayed_list from dumping all its stripes onto the handle_list in one shot. Delayed stripes are now further delayed by being held on the 'hold_list'. The 'hold_list' is bypassed when: * a STRIPE_IO_STARTED stripe is found at the head of 'handle_list' * 'handle_list' is empty and i/o is being done to satisfy full stripe-width write requests * 'bypass_count' is less than 'bypass_threshold'. By default the threshold is 1, i.e. every other stripe handled is a preread stripe provided the top two conditions are false. Benchmark data: System: 2x Xeon 5150, 4x SATA, mem=1GB Baseline: 2.6.24-rc7 Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048 * patched: +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512) Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS) * patched: +13% * patched + preread_bypass_threshold = 0: +37% Changes since v1: * reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and make it configurable. This defaults to fairness and modest performance gains out of the box. Changes since v2: * [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not necessary, the important change was clearing STRIPE_DELAYED in add_stripe_bio and this has been moved out to make_request for the hang fix. * [neilb@suse.de]: simplify get_priority_stripe * [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is sampled empty (+11%) * [dan.j.williams@intel.com]: decrement the bypass_count at the detection of stripes being naturally promoted off of hold_list +2%. Note, resetting bypass_count instead of decrementing on these events yields +4% but that is probably too aggressive. Changes since v3: * cosmetic fixups Tested-by: James W. Laferriere <babydr@baby-dragons.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:15:53 +08:00
atomic_t pending_full_writes; /* full write backlog */
int bypass_count; /* bypassed prereads */
int bypass_threshold; /* preread nice */
int skip_copy; /* Don't copy data from bio to stripe cache */
md: introduce get_priority_stripe() to improve raid456 write performance Improve write performance by preventing the delayed_list from dumping all its stripes onto the handle_list in one shot. Delayed stripes are now further delayed by being held on the 'hold_list'. The 'hold_list' is bypassed when: * a STRIPE_IO_STARTED stripe is found at the head of 'handle_list' * 'handle_list' is empty and i/o is being done to satisfy full stripe-width write requests * 'bypass_count' is less than 'bypass_threshold'. By default the threshold is 1, i.e. every other stripe handled is a preread stripe provided the top two conditions are false. Benchmark data: System: 2x Xeon 5150, 4x SATA, mem=1GB Baseline: 2.6.24-rc7 Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048 * patched: +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512) Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS) * patched: +13% * patched + preread_bypass_threshold = 0: +37% Changes since v1: * reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and make it configurable. This defaults to fairness and modest performance gains out of the box. Changes since v2: * [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not necessary, the important change was clearing STRIPE_DELAYED in add_stripe_bio and this has been moved out to make_request for the hang fix. * [neilb@suse.de]: simplify get_priority_stripe * [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is sampled empty (+11%) * [dan.j.williams@intel.com]: decrement the bypass_count at the detection of stripes being naturally promoted off of hold_list +2%. Note, resetting bypass_count instead of decrementing on these events yields +4% but that is probably too aggressive. Changes since v3: * cosmetic fixups Tested-by: James W. Laferriere <babydr@baby-dragons.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:15:53 +08:00
struct list_head *last_hold; /* detect hold_list promotions */
atomic_t reshape_stripes; /* stripes with pending writes for reshape */
/* unfortunately we need two cache names as we temporarily have
* two caches.
*/
int active_name;
char cache_name[2][32];
struct kmem_cache *slab_cache; /* for allocating stripes */
struct mutex cache_size_mutex; /* Protect changes to cache size */
int seq_flush, seq_write;
int quiesce;
int fullsync; /* set to 1 if a full sync is needed,
* (fresh device added).
* Cleared when a sync completes.
*/
int recovery_disabled;
/* per cpu variables */
struct raid5_percpu {
struct page *spare_page; /* Used when checking P/Q in raid6 */
void *scribble; /* space for constructing buffer
* lists and performing address
* conversions
*/
int scribble_obj_size;
} __percpu *percpu;
int scribble_disks;
int scribble_sectors;
struct hlist_node node;
/*
* Free stripes pool
*/
atomic_t active_stripes;
raid5: relieve lock contention in get_active_stripe() get_active_stripe() is the last place we have lock contention. It has two paths. One is stripe isn't found and new stripe is allocated, the other is stripe is found. The first path basically calls __find_stripe and init_stripe. It accesses conf->generation, conf->previous_raid_disks, conf->raid_disks, conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded, conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except stripe_hashtbl and inactive_list, other fields are changed very rarely. With this patch, we split inactive_list and add new hash locks. Each free stripe belongs to a specific inactive list. Which inactive list is determined by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a lock_hash assigned. Stripe's inactive list is protected by a hash lock, which is determined by it's lock_hash too. The lock_hash is derivied from current stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl list too. The goal of the new hash locks introduced is we can only use the new locks in the first path of get_active_stripe(). Since we have several hash locks, lock contention is relieved significantly. The first path of get_active_stripe() accesses other fields, since they are changed rarely, changing them now need take conf->device_lock and all hash locks. For a slow path, this isn't a problem. If we need lock device_lock and hash lock, we always lock hash lock first. The tricky part is release_stripe and friends. We need take device_lock first. Neil's suggestion is we put inactive stripes to a temporary list and readd it to inactive_list after device_lock is released. In this way, we add stripes to temporary list with device_lock hold and remove stripes from the list with hash lock hold. So we don't allow concurrent access to the temporary list, which means we need allocate temporary list for all participants of release_stripe. One downside is free stripes are maintained in their inactive list, they can't across between the lists. By default, we have total 256 stripes and 8 lists, so each list will have 32 stripes. It's possible one list has free stripe but other list hasn't. The chance should be rare because stripes allocation are even distributed. And we can always allocate more stripes for cache, several mega bytes memory isn't a big deal. This completely removes the lock contention of the first path of get_active_stripe(). It slows down the second code path a little bit though because we now need takes two locks, but since the hash lock isn't contended, the overhead should be quite small (several atomic instructions). The second path of get_active_stripe() (basically sequential write or big request size randwrite) still has lock contentions. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-11-14 12:16:17 +08:00
struct list_head inactive_list[NR_STRIPE_HASH_LOCKS];
md/r5cache: caching phase of r5cache As described in previous patch, write back cache operates in two phases: caching and writing-out. The caching phase works as: 1. write data to journal (r5c_handle_stripe_dirtying, r5c_cache_data) 2. call bio_endio (r5c_handle_data_cached, r5c_return_dev_pending_writes). Then the writing-out phase is as: 1. Mark the stripe as write-out (r5c_make_stripe_write_out) 2. Calcualte parity (reconstruct or RMW) 3. Write parity (and maybe some other data) to journal device 4. Write data and parity to RAID disks This patch implements caching phase. The cache is integrated with stripe cache of raid456. It leverages code of r5l_log to write data to journal device. Writing-out phase of the cache is implemented in the next patch. With r5cache, write operation does not wait for parity calculation and write out, so the write latency is lower (1 write to journal device vs. read and then write to raid disks). Also, r5cache will reduce RAID overhead (multipile IO due to read-modify-write of parity) and provide more opportunities of full stripe writes. This patch adds 2 flags to stripe_head.state: - STRIPE_R5C_PARTIAL_STRIPE, - STRIPE_R5C_FULL_STRIPE, Instead of inactive_list, stripes with cached data are tracked in r5conf->r5c_full_stripe_list and r5conf->r5c_partial_stripe_list. STRIPE_R5C_FULL_STRIPE and STRIPE_R5C_PARTIAL_STRIPE are flags for stripes in these lists. Note: stripes in r5c_full/partial_stripe_list are not considered as "active". For RMW, the code allocates an extra page for each data block being updated. This is stored in r5dev->orig_page and the old data is read into it. Then the prexor calculation subtracts ->orig_page from the parity block, and the reconstruct calculation adds the ->page data back into the parity block. r5cache naturally excludes SkipCopy. When the array has write back cache, async_copy_data() will not skip copy. There are some known limitations of the cache implementation: 1. Write cache only covers full page writes (R5_OVERWRITE). Writes of smaller granularity are write through. 2. Only one log io (sh->log_io) for each stripe at anytime. Later writes for the same stripe have to wait. This can be improved by moving log_io to r5dev. 3. With writeback cache, read path must enter state machine, which is a significant bottleneck for some workloads. 4. There is no per stripe checkpoint (with r5l_payload_flush) in the log, so recovery code has to replay more than necessary data (sometimes all the log from last_checkpoint). This reduces availability of the array. This patch includes a fix proposed by ZhengYuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:39 +08:00
atomic_t r5c_cached_full_stripes;
struct list_head r5c_full_stripe_list;
atomic_t r5c_cached_partial_stripes;
struct list_head r5c_partial_stripe_list;
atomic_t r5c_flushing_full_stripes;
atomic_t r5c_flushing_partial_stripes;
md/r5cache: caching phase of r5cache As described in previous patch, write back cache operates in two phases: caching and writing-out. The caching phase works as: 1. write data to journal (r5c_handle_stripe_dirtying, r5c_cache_data) 2. call bio_endio (r5c_handle_data_cached, r5c_return_dev_pending_writes). Then the writing-out phase is as: 1. Mark the stripe as write-out (r5c_make_stripe_write_out) 2. Calcualte parity (reconstruct or RMW) 3. Write parity (and maybe some other data) to journal device 4. Write data and parity to RAID disks This patch implements caching phase. The cache is integrated with stripe cache of raid456. It leverages code of r5l_log to write data to journal device. Writing-out phase of the cache is implemented in the next patch. With r5cache, write operation does not wait for parity calculation and write out, so the write latency is lower (1 write to journal device vs. read and then write to raid disks). Also, r5cache will reduce RAID overhead (multipile IO due to read-modify-write of parity) and provide more opportunities of full stripe writes. This patch adds 2 flags to stripe_head.state: - STRIPE_R5C_PARTIAL_STRIPE, - STRIPE_R5C_FULL_STRIPE, Instead of inactive_list, stripes with cached data are tracked in r5conf->r5c_full_stripe_list and r5conf->r5c_partial_stripe_list. STRIPE_R5C_FULL_STRIPE and STRIPE_R5C_PARTIAL_STRIPE are flags for stripes in these lists. Note: stripes in r5c_full/partial_stripe_list are not considered as "active". For RMW, the code allocates an extra page for each data block being updated. This is stored in r5dev->orig_page and the old data is read into it. Then the prexor calculation subtracts ->orig_page from the parity block, and the reconstruct calculation adds the ->page data back into the parity block. r5cache naturally excludes SkipCopy. When the array has write back cache, async_copy_data() will not skip copy. There are some known limitations of the cache implementation: 1. Write cache only covers full page writes (R5_OVERWRITE). Writes of smaller granularity are write through. 2. Only one log io (sh->log_io) for each stripe at anytime. Later writes for the same stripe have to wait. This can be improved by moving log_io to r5dev. 3. With writeback cache, read path must enter state machine, which is a significant bottleneck for some workloads. 4. There is no per stripe checkpoint (with r5l_payload_flush) in the log, so recovery code has to replay more than necessary data (sometimes all the log from last_checkpoint). This reduces availability of the array. This patch includes a fix proposed by ZhengYuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-11-18 07:24:39 +08:00
atomic_t empty_inactive_list_nr;
struct llist_head released_stripes;
wait_queue_head_t wait_for_quiescent;
wait_queue_head_t wait_for_stripe;
wait_queue_head_t wait_for_overlap;
unsigned long cache_state;
md/raid5: allow the stripe_cache to grow and shrink. The default setting of 256 stripe_heads is probably much too small for many configurations. So it is best to make it auto-configure. Shrinking the cache under memory pressure is easy. The only interesting part here is that we put a fairly high cost ('seeks') on shrinking the cache as the cost is greater than just having to read more data, it reduces parallelism. Growing the cache on demand needs to be done carefully. If we allow fast growth, that can upset memory balance as lots of dirty memory can quickly turn into lots of memory queued in the stripe_cache. It is important for the raid5 block device to appear congested to allow write-throttling to work. So we only add stripes slowly. We set a flag when an allocation fails because all stripes are in use, allocate at a convenient time when that flag is set, and don't allow it to be set again until at least one stripe_head has been released for re-use. This means that a spurt of requests will only cause one stripe_head to be allocated, but a steady stream of requests will slowly increase the cache size - until memory pressure puts it back again. It could take hours to reach a steady state. The value written to, and displayed in, stripe_cache_size is used as a minimum. The cache can grow above this and shrink back down to it. The actual size is not directly visible, though it can be deduced to some extent by watching stripe_cache_active. Signed-off-by: NeilBrown <neilb@suse.de>
2015-02-26 09:47:56 +08:00
struct shrinker shrinker;
int pool_size; /* number of disks in stripeheads in pool */
spinlock_t device_lock;
struct disk_info *disks;
struct bio_set bio_split;
/* When taking over an array from a different personality, we store
* the new thread here until we fully activate the array.
*/
struct md_thread *thread;
raid5: relieve lock contention in get_active_stripe() get_active_stripe() is the last place we have lock contention. It has two paths. One is stripe isn't found and new stripe is allocated, the other is stripe is found. The first path basically calls __find_stripe and init_stripe. It accesses conf->generation, conf->previous_raid_disks, conf->raid_disks, conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded, conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except stripe_hashtbl and inactive_list, other fields are changed very rarely. With this patch, we split inactive_list and add new hash locks. Each free stripe belongs to a specific inactive list. Which inactive list is determined by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a lock_hash assigned. Stripe's inactive list is protected by a hash lock, which is determined by it's lock_hash too. The lock_hash is derivied from current stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl list too. The goal of the new hash locks introduced is we can only use the new locks in the first path of get_active_stripe(). Since we have several hash locks, lock contention is relieved significantly. The first path of get_active_stripe() accesses other fields, since they are changed rarely, changing them now need take conf->device_lock and all hash locks. For a slow path, this isn't a problem. If we need lock device_lock and hash lock, we always lock hash lock first. The tricky part is release_stripe and friends. We need take device_lock first. Neil's suggestion is we put inactive stripes to a temporary list and readd it to inactive_list after device_lock is released. In this way, we add stripes to temporary list with device_lock hold and remove stripes from the list with hash lock hold. So we don't allow concurrent access to the temporary list, which means we need allocate temporary list for all participants of release_stripe. One downside is free stripes are maintained in their inactive list, they can't across between the lists. By default, we have total 256 stripes and 8 lists, so each list will have 32 stripes. It's possible one list has free stripe but other list hasn't. The chance should be rare because stripes allocation are even distributed. And we can always allocate more stripes for cache, several mega bytes memory isn't a big deal. This completely removes the lock contention of the first path of get_active_stripe(). It slows down the second code path a little bit though because we now need takes two locks, but since the hash lock isn't contended, the overhead should be quite small (several atomic instructions). The second path of get_active_stripe() (basically sequential write or big request size randwrite) still has lock contentions. Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-11-14 12:16:17 +08:00
struct list_head temp_inactive_list[NR_STRIPE_HASH_LOCKS];
raid5: offload stripe handle to workqueue This is another attempt to create multiple threads to handle raid5 stripes. This time I use workqueue. raid5 handles request (especially write) in stripe unit. A stripe is page size aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a state machine for the corresponding stripe, which includes reading some disks of the stripe, calculating parity, and writing some disks of the stripe. The state machine is running in raid5d thread currently. Since there is only one thread, it doesn't scale well for high speed storage. An obvious solution is multi-threading. To get better performance, we have some requirements: a. locality. stripe corresponding to request submitted from one cpu is better handled in thread in local cpu or local node. local cpu is preferred but some times could be a bottleneck, for example, parity calculation is too heavy. local node running has wide adaptability. b. configurablity. Different setup of raid5 array might need diffent configuration. Especially the thread number. More threads don't always mean better performance because of lock contentions. My original implementation is creating some kernel threads. There are interfaces to control which cpu's stripe each thread should handle. And userspace can set affinity of the threads. This provides biggest flexibility and configurability. But it's hard to use and apparently a new thread pool implementation is disfavor. Recent workqueue improvement is quite promising. unbound workqueue will be bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to do affinity setting. For example, we can only include one HT sibling in affinity. Since work is non-reentrant by default, and we can control running thread number by limiting dispatched work_struct number. In this patch, I created several stripe worker group. A group is a numa node. stripes from cpus of one node will be added to a group list. Workqueue thread of one node will only handle stripes of worker group of the node. In this way, stripe handling has numa node locality. And as I said, we can control thread number by limiting dispatched work_struct number. The work_struct callback function handles several stripes in one run. A typical work queue usage is to run one unit in each work_struct. In raid5 case, the unit is a stripe. But we can't do that: a. Though handling a stripe doesn't need lock because of reference accounting and stripe isn't in any list, queuing a work_struct for each stripe will make workqueue lock contended very heavily. b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we might dispatch request. If each work_struct only handles one stripe, such block plug is meaningless. This implementation can't do very fine grained configuration. But the numa binding is most popular usage model, should be enough for most workloads. Note: since we have only one stripe queue, switching to multi-thread might decrease request size dispatching down to low level layer. The impact depends on thread number, raid configuration and workload. So multi-thread raid5 might not be proper for all setups. Changes V1 -> V2: 1. remove WQ_NON_REENTRANT 2. disabling multi-threading by default 3. Add more descriptions in changelog Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-08-28 14:30:16 +08:00
struct r5worker_group *worker_groups;
int group_cnt;
int worker_cnt_per_group;
raid5: add basic stripe log This introduces a simple log for raid5. Data/parity writing to raid array first writes to the log, then write to raid array disks. If crash happens, we can recovery data from the log. This can speed up raid resync and fix write hole issue. The log structure is pretty simple. Data/meta data is stored in block unit, which is 4k generally. It has only one type of meta data block. The meta data block can track 3 types of data, stripe data, stripe parity and flush block. MD superblock will point to the last valid meta data block. Each meta data block has checksum/seq number, so recovery can scan the log correctly. We store a checksum of stripe data/parity to the metadata block, so meta data and stripe data/parity can be written to log disk together. otherwise, meta data write must wait till stripe data/parity is finished. For stripe data, meta data block will record stripe data sector and size. Currently the size is always 4k. This meta data record can be made simpler if we just fix write hole (eg, we can record data of a stripe's different disks together), but this format can be extended to support caching in the future, which must record data address/size. For stripe parity, meta data block will record stripe sector. It's size should be 4k (for raid5) or 8k (for raid6). We always store p parity first. This format should work for caching too. flush block indicates a stripe is in raid array disks. Fixing write hole doesn't need this type of meta data, it's for caching extension. Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-14 05:31:59 +08:00
struct r5l_log *log;
void *log_private;
spinlock_t pending_bios_lock;
bool batch_bio_dispatch;
struct r5pending_data *pending_data;
struct list_head free_list;
struct list_head pending_list;
int pending_data_cnt;
struct r5pending_data *next_pending_data;
};
/*
* Our supported algorithms
*/
#define ALGORITHM_LEFT_ASYMMETRIC 0 /* Rotating Parity N with Data Restart */
#define ALGORITHM_RIGHT_ASYMMETRIC 1 /* Rotating Parity 0 with Data Restart */
#define ALGORITHM_LEFT_SYMMETRIC 2 /* Rotating Parity N with Data Continuation */
#define ALGORITHM_RIGHT_SYMMETRIC 3 /* Rotating Parity 0 with Data Continuation */
/* Define non-rotating (raid4) algorithms. These allow
* conversion of raid4 to raid5.
*/
#define ALGORITHM_PARITY_0 4 /* P or P,Q are initial devices */
#define ALGORITHM_PARITY_N 5 /* P or P,Q are final devices. */
/* DDF RAID6 layouts differ from md/raid6 layouts in two ways.
* Firstly, the exact positioning of the parity block is slightly
* different between the 'LEFT_*' modes of md and the "_N_*" modes
* of DDF.
* Secondly, or order of datablocks over which the Q syndrome is computed
* is different.
* Consequently we have different layouts for DDF/raid6 than md/raid6.
* These layouts are from the DDFv1.2 spec.
* Interestingly DDFv1.2-Errata-A does not specify N_CONTINUE but
* leaves RLQ=3 as 'Vendor Specific'
*/
#define ALGORITHM_ROTATING_ZERO_RESTART 8 /* DDF PRL=6 RLQ=1 */
#define ALGORITHM_ROTATING_N_RESTART 9 /* DDF PRL=6 RLQ=2 */
#define ALGORITHM_ROTATING_N_CONTINUE 10 /*DDF PRL=6 RLQ=3 */
/* For every RAID5 algorithm we define a RAID6 algorithm
* with exactly the same layout for data and parity, and
* with the Q block always on the last device (N-1).
* This allows trivial conversion from RAID5 to RAID6
*/
#define ALGORITHM_LEFT_ASYMMETRIC_6 16
#define ALGORITHM_RIGHT_ASYMMETRIC_6 17
#define ALGORITHM_LEFT_SYMMETRIC_6 18
#define ALGORITHM_RIGHT_SYMMETRIC_6 19
#define ALGORITHM_PARITY_0_6 20
#define ALGORITHM_PARITY_N_6 ALGORITHM_PARITY_N
static inline int algorithm_valid_raid5(int layout)
{
return (layout >= 0) &&
(layout <= 5);
}
static inline int algorithm_valid_raid6(int layout)
{
return (layout >= 0 && layout <= 5)
||
(layout >= 8 && layout <= 10)
||
(layout >= 16 && layout <= 20);
}
static inline int algorithm_is_DDF(int layout)
{
return layout >= 8 && layout <= 10;
}
extern void md_raid5_kick_device(struct r5conf *conf);
extern int raid5_set_cache_size(struct mddev *mddev, int size);
extern sector_t raid5_compute_blocknr(struct stripe_head *sh, int i, int previous);
extern void raid5_release_stripe(struct stripe_head *sh);
extern sector_t raid5_compute_sector(struct r5conf *conf, sector_t r_sector,
int previous, int *dd_idx,
struct stripe_head *sh);
extern struct stripe_head *
raid5_get_active_stripe(struct r5conf *conf, sector_t sector,
int previous, int noblock, int noquiesce);
extern int raid5_calc_degraded(struct r5conf *conf);
extern int r5c_journal_mode_set(struct mddev *mddev, int journal_mode);
#endif