OpenCloudOS-Kernel/drivers/net/wireless/ath/ath9k/hw.h

1172 lines
34 KiB
C
Raw Normal View History

/*
* Copyright (c) 2008-2011 Atheros Communications Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
#ifndef HW_H
#define HW_H
#include <linux/if_ether.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/firmware.h>
#include "mac.h"
#include "ani.h"
#include "eeprom.h"
#include "calib.h"
#include "reg.h"
#include "phy.h"
#include "btcoex.h"
#include "../regd.h"
#define ATHEROS_VENDOR_ID 0x168c
#define AR5416_DEVID_PCI 0x0023
#define AR5416_DEVID_PCIE 0x0024
#define AR9160_DEVID_PCI 0x0027
#define AR9280_DEVID_PCI 0x0029
#define AR9280_DEVID_PCIE 0x002a
#define AR9285_DEVID_PCIE 0x002b
#define AR2427_DEVID_PCIE 0x002c
#define AR9287_DEVID_PCI 0x002d
#define AR9287_DEVID_PCIE 0x002e
#define AR9300_DEVID_PCIE 0x0030
#define AR9300_DEVID_AR9340 0x0031
#define AR9300_DEVID_AR9485_PCIE 0x0032
ath9k_hw: add AR9580 support Here are the AR9580 1.0 initvals checksums using the Atheros initvals-tools [1]. This is useful for when we udate the initvals again with other values. It ensures that we match the same initvals used internally. The tool is documented on the wiki [2]. $ ./initvals -f ar9580-1p0 0x00000000e912711f ar9580_1p0_modes_fast_clock 0x000000004a488fc7 ar9580_1p0_radio_postamble 0x00000000f3888b02 ar9580_1p0_baseband_core 0x0000000003f783bb ar9580_1p0_mac_postamble 0x0000000094be244a ar9580_1p0_low_ob_db_tx_gain_table 0x0000000094be244a ar9580_1p0_high_power_tx_gain_table 0x0000000090be244a ar9580_1p0_lowest_ob_db_tx_gain_table 0x00000000ed9eaac6 ar9580_1p0_baseband_core_txfir_coeff_japan_2484 0x00000000c4d66d1b ar9580_1p0_mac_core 0x00000000e8e9043a ar9580_1p0_mixed_ob_db_tx_gain_table 0x000000003521a300 ar9580_1p0_wo_xlna_rx_gain_table 0x00000000301fc841 ar9580_1p0_soc_postamble 0x00000000a9a06b3a ar9580_1p0_high_ob_db_tx_gain_table 0x00000000a15ccf1b ar9580_1p0_soc_preamble 0x0000000029495000 ar9580_1p0_rx_gain_table 0x0000000037ac0ee8 ar9580_1p0_radio_core 0x00000000603a1b80 ar9580_1p0_baseband_postamble 0x000000003d8b4396 ar9580_1p0_pcie_phy_clkreq_enable_L1 0x00000000398b4396 ar9580_1p0_pcie_phy_clkreq_disable_L1 0x00000000397b4396 ar9580_1p0_pcie_phy_pll_on_clkreq [1] git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git [2] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool Cc: David Quan <dquan@qca.qualcomm.com> Cc: Kathy Giori <kgiori@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-25 06:36:08 +08:00
#define AR9300_DEVID_AR9580 0x0033
#define AR9300_DEVID_AR9462 0x0034
#define AR9300_DEVID_AR9330 0x0035
#define AR9300_DEVID_QCA955X 0x0038
#define AR9485_DEVID_AR1111 0x0037
#define AR9300_DEVID_AR9565 0x0036
#define AR5416_AR9100_DEVID 0x000b
#define AR_SUBVENDOR_ID_NOG 0x0e11
#define AR_SUBVENDOR_ID_NEW_A 0x7065
#define AR5416_MAGIC 0x19641014
#define AR9280_COEX2WIRE_SUBSYSID 0x309b
#define AT9285_COEX3WIRE_SA_SUBSYSID 0x30aa
#define AT9285_COEX3WIRE_DA_SUBSYSID 0x30ab
#define ATH_AMPDU_LIMIT_MAX (64 * 1024 - 1)
#define ATH_DEFAULT_NOISE_FLOOR -95
#define ATH9K_RSSI_BAD -128
#define ATH9K_NUM_CHANNELS 38
/* Register read/write primitives */
#define REG_WRITE(_ah, _reg, _val) \
(_ah)->reg_ops.write((_ah), (_val), (_reg))
#define REG_READ(_ah, _reg) \
(_ah)->reg_ops.read((_ah), (_reg))
#define REG_READ_MULTI(_ah, _addr, _val, _cnt) \
(_ah)->reg_ops.multi_read((_ah), (_addr), (_val), (_cnt))
#define REG_RMW(_ah, _reg, _set, _clr) \
(_ah)->reg_ops.rmw((_ah), (_reg), (_set), (_clr))
#define ENABLE_REGWRITE_BUFFER(_ah) \
do { \
if ((_ah)->reg_ops.enable_write_buffer) \
(_ah)->reg_ops.enable_write_buffer((_ah)); \
} while (0)
#define REGWRITE_BUFFER_FLUSH(_ah) \
do { \
if ((_ah)->reg_ops.write_flush) \
(_ah)->reg_ops.write_flush((_ah)); \
} while (0)
#define PR_EEP(_s, _val) \
do { \
len += snprintf(buf + len, size - len, "%20s : %10d\n", \
_s, (_val)); \
} while (0)
#define SM(_v, _f) (((_v) << _f##_S) & _f)
#define MS(_v, _f) (((_v) & _f) >> _f##_S)
#define REG_RMW_FIELD(_a, _r, _f, _v) \
REG_RMW(_a, _r, (((_v) << _f##_S) & _f), (_f))
#define REG_READ_FIELD(_a, _r, _f) \
(((REG_READ(_a, _r) & _f) >> _f##_S))
#define REG_SET_BIT(_a, _r, _f) \
REG_RMW(_a, _r, (_f), 0)
#define REG_CLR_BIT(_a, _r, _f) \
REG_RMW(_a, _r, 0, (_f))
#define DO_DELAY(x) do { \
if (((++(x) % 64) == 0) && \
(ath9k_hw_common(ah)->bus_ops->ath_bus_type \
!= ATH_USB)) \
udelay(1); \
} while (0)
#define REG_WRITE_ARRAY(iniarray, column, regWr) \
ath9k_hw_write_array(ah, iniarray, column, &(regWr))
#define AR_GPIO_OUTPUT_MUX_AS_OUTPUT 0
#define AR_GPIO_OUTPUT_MUX_AS_PCIE_ATTENTION_LED 1
#define AR_GPIO_OUTPUT_MUX_AS_PCIE_POWER_LED 2
#define AR_GPIO_OUTPUT_MUX_AS_TX_FRAME 3
#define AR_GPIO_OUTPUT_MUX_AS_RX_CLEAR_EXTERNAL 4
#define AR_GPIO_OUTPUT_MUX_AS_MAC_NETWORK_LED 5
#define AR_GPIO_OUTPUT_MUX_AS_MAC_POWER_LED 6
#define AR_GPIO_OUTPUT_MUX_AS_MCI_WLAN_DATA 0x16
#define AR_GPIO_OUTPUT_MUX_AS_MCI_WLAN_CLK 0x17
#define AR_GPIO_OUTPUT_MUX_AS_MCI_BT_DATA 0x18
#define AR_GPIO_OUTPUT_MUX_AS_MCI_BT_CLK 0x19
#define AR_GPIO_OUTPUT_MUX_AS_WL_IN_TX 0x14
#define AR_GPIO_OUTPUT_MUX_AS_WL_IN_RX 0x13
#define AR_GPIO_OUTPUT_MUX_AS_BT_IN_TX 9
#define AR_GPIO_OUTPUT_MUX_AS_BT_IN_RX 8
#define AR_GPIO_OUTPUT_MUX_AS_RUCKUS_STROBE 0x1d
#define AR_GPIO_OUTPUT_MUX_AS_RUCKUS_DATA 0x1e
#define AR_GPIOD_MASK 0x00001FFF
#define AR_GPIO_BIT(_gpio) (1 << (_gpio))
#define BASE_ACTIVATE_DELAY 100
#define RTC_PLL_SETTLE_DELAY (AR_SREV_9340(ah) ? 1000 : 100)
#define COEF_SCALE_S 24
#define HT40_CHANNEL_CENTER_SHIFT 10
#define ATH9K_ANTENNA0_CHAINMASK 0x1
#define ATH9K_ANTENNA1_CHAINMASK 0x2
#define ATH9K_NUM_DMA_DEBUG_REGS 8
#define ATH9K_NUM_QUEUES 10
#define MAX_RATE_POWER 63
#define AH_WAIT_TIMEOUT 100000 /* (us) */
#define AH_TSF_WRITE_TIMEOUT 100 /* (us) */
#define AH_TIME_QUANTUM 10
#define AR_KEYTABLE_SIZE 128
#define POWER_UP_TIME 10000
#define SPUR_RSSI_THRESH 40
#define UPPER_5G_SUB_BAND_START 5700
#define MID_5G_SUB_BAND_START 5400
#define CAB_TIMEOUT_VAL 10
#define BEACON_TIMEOUT_VAL 10
#define MIN_BEACON_TIMEOUT_VAL 1
#define SLEEP_SLOP 3
#define INIT_CONFIG_STATUS 0x00000000
#define INIT_RSSI_THR 0x00000700
#define INIT_BCON_CNTRL_REG 0x00000000
#define TU_TO_USEC(_tu) ((_tu) << 10)
#define ATH9K_HW_RX_HP_QDEPTH 16
#define ATH9K_HW_RX_LP_QDEPTH 128
#define PAPRD_GAIN_TABLE_ENTRIES 32
#define PAPRD_TABLE_SZ 24
#define PAPRD_IDEAL_AGC2_PWR_RANGE 0xe0
/*
* Wake on Wireless
*/
/* Keep Alive Frame */
#define KAL_FRAME_LEN 28
#define KAL_FRAME_TYPE 0x2 /* data frame */
#define KAL_FRAME_SUB_TYPE 0x4 /* null data frame */
#define KAL_DURATION_ID 0x3d
#define KAL_NUM_DATA_WORDS 6
#define KAL_NUM_DESC_WORDS 12
#define KAL_ANTENNA_MODE 1
#define KAL_TO_DS 1
#define KAL_DELAY 4 /*delay of 4ms between 2 KAL frames */
#define KAL_TIMEOUT 900
#define MAX_PATTERN_SIZE 256
#define MAX_PATTERN_MASK_SIZE 32
#define MAX_NUM_PATTERN 8
#define MAX_NUM_USER_PATTERN 6 /* deducting the disassociate and
deauthenticate packets */
/*
* WoW trigger mapping to hardware code
*/
#define AH_WOW_USER_PATTERN_EN BIT(0)
#define AH_WOW_MAGIC_PATTERN_EN BIT(1)
#define AH_WOW_LINK_CHANGE BIT(2)
#define AH_WOW_BEACON_MISS BIT(3)
ath9k: rework tx queue selection and fix queue stopping/waking The current ath9k tx queue handling code showed a few issues that could lead to locking issues, tx stalls due to stopped queues, and maybe even DMA issues. The main source of these issues is that in some places the queue is selected via skb queue mapping in places where this mapping may no longer be valid. One such place is when data frames are transmitted via the CAB queue (for powersave buffered frames). This is made even worse by a lookup WMM AC values from the assigned tx queue (which is undefined for the CAB queue). This messed up the pending frame counting, which in turn caused issues with queues getting stopped, but not woken again. To fix these issues, this patch removes an unnecessary abstraction separating a driver internal queue number from the skb queue number (not to be confused with the hardware queue number). It seems that this abstraction may have been necessary because of tx queue preinitialization from the initvals. This patch avoids breakage here by pushing the software <-> hardware queue mapping to the function that assigns the tx queues and redefining the WMM AC definitions to match the numbers used by mac80211 (also affects ath9k_htc). To ensure consistency wrt. pending frame count tracking, these counters are moved to the ath_txq struct, updated with the txq lock held, but only where the tx queue selected by the skb queue map actually matches the tx queue used by the driver for the frame. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Björn Smedman <bjorn.smedman@venatech.se> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-07 21:59:39 +08:00
enum ath_hw_txq_subtype {
ATH_TXQ_AC_BE = 0,
ATH_TXQ_AC_BK = 1,
ATH_TXQ_AC_VI = 2,
ATH_TXQ_AC_VO = 3,
};
enum ath_ini_subsys {
ATH_INI_PRE = 0,
ATH_INI_CORE,
ATH_INI_POST,
ATH_INI_NUM_SPLIT,
};
enum ath9k_hw_caps {
ATH9K_HW_CAP_HT = BIT(0),
ATH9K_HW_CAP_RFSILENT = BIT(1),
ATH9K_HW_CAP_AUTOSLEEP = BIT(2),
ATH9K_HW_CAP_4KB_SPLITTRANS = BIT(3),
ATH9K_HW_CAP_EDMA = BIT(4),
ATH9K_HW_CAP_RAC_SUPPORTED = BIT(5),
ATH9K_HW_CAP_LDPC = BIT(6),
ATH9K_HW_CAP_FASTCLOCK = BIT(7),
ATH9K_HW_CAP_SGI_20 = BIT(8),
ATH9K_HW_CAP_ANT_DIV_COMB = BIT(10),
ATH9K_HW_CAP_2GHZ = BIT(11),
ATH9K_HW_CAP_5GHZ = BIT(12),
ATH9K_HW_CAP_APM = BIT(13),
ATH9K_HW_CAP_RTT = BIT(14),
ATH9K_HW_CAP_MCI = BIT(15),
ATH9K_HW_CAP_DFS = BIT(16),
ATH9K_HW_WOW_DEVICE_CAPABLE = BIT(17),
ATH9K_HW_CAP_PAPRD = BIT(18),
};
/*
* WoW device capabilities
* @ATH9K_HW_WOW_DEVICE_CAPABLE: device revision is capable of WoW.
* @ATH9K_HW_WOW_PATTERN_MATCH_EXACT: device is capable of matching
* an exact user defined pattern or de-authentication/disassoc pattern.
* @ATH9K_HW_WOW_PATTERN_MATCH_DWORD: device requires the first four
* bytes of the pattern for user defined pattern, de-authentication and
* disassociation patterns for all types of possible frames recieved
* of those types.
*/
struct ath9k_hw_capabilities {
u32 hw_caps; /* ATH9K_HW_CAP_* from ath9k_hw_caps */
u16 rts_aggr_limit;
u8 tx_chainmask;
u8 rx_chainmask;
u8 max_txchains;
u8 max_rxchains;
u8 num_gpio_pins;
u8 rx_hp_qdepth;
u8 rx_lp_qdepth;
u8 rx_status_len;
u8 tx_desc_len;
u8 txs_len;
};
struct ath9k_ops_config {
int dma_beacon_response_time;
int sw_beacon_response_time;
int additional_swba_backoff;
int ack_6mb;
u32 cwm_ignore_extcca;
bool pcieSerDesWrite;
u8 pcie_clock_req;
u32 pcie_waen;
u8 analog_shiftreg;
u32 ofdm_trig_low;
u32 ofdm_trig_high;
u32 cck_trig_high;
u32 cck_trig_low;
u32 enable_paprd;
int serialize_regmode;
bool rx_intr_mitigation;
bool tx_intr_mitigation;
#define SPUR_DISABLE 0
#define SPUR_ENABLE_IOCTL 1
#define SPUR_ENABLE_EEPROM 2
#define AR_SPUR_5413_1 1640
#define AR_SPUR_5413_2 1200
#define AR_NO_SPUR 0x8000
#define AR_BASE_FREQ_2GHZ 2300
#define AR_BASE_FREQ_5GHZ 4900
#define AR_SPUR_FEEQ_BOUND_HT40 19
#define AR_SPUR_FEEQ_BOUND_HT20 10
int spurmode;
u16 spurchans[AR_EEPROM_MODAL_SPURS][2];
ath9k: Fix maximum tx fifo settings for single stream devices Atheros single stream AR9285 and AR9271 have half the PCU TX FIFO buffer size of that of dual stream devices. Dual stream devices have a max PCU TX FIFO size of 8 KB while single stream devices have 4 KB. Single stream devices have an issue though and require hardware only to use half of the amount of its capable PCU TX FIFO size, 2 KB and this requires a change in software. Technically a change would not have been required (except for frame burst considerations of 128 bytes) if these devices would have been able to use the full 4 KB of the PCU TX FIFO size but our systems engineers recommend 2 KB to be used only. We enforce this through software by reducing the max frame triggger level to 2 KB. Fixing the max frame trigger level should then have a few benefits: * The PER will now be adjusted as designed for underruns when the max trigger level is reached. This should help alleviate the bus as the rate control algorithm chooses a slower rate which should ensure frames are transmitted properly under high system bus load. * The poll we use on our TX queues should now trigger and work as designed for single stream devices. The hardware passes data from each TX queue on the PCU TX FIFO queue respecting each queue's priority. The new trigger level ensures this seeding of the PCU TX FIFO queue occurs as designed which could mean avoiding false resets and actually reseting hw correctly when a TX queue is indeed stuck. * Some undocumented / unsupported behaviour could have been triggered when the max trigger level level was being set to 4 KB on single stream devices. Its not clear what this issue was to me yet. Cc: Kyungwan Nam <kyungwan.nam@atheros.com> Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com> Cc: Stephen Chen <stephen.chen@atheros.com> Cc: Shan Palanisamy <shan.palanisamy@atheros.com> Cc: Paul Shaw <paul.shaw@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-25 10:37:57 +08:00
u8 max_txtrig_level;
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
u16 ani_poll_interval; /* ANI poll interval in ms */
/* Platform specific config */
u32 xlna_gpio;
bool xatten_margin_cfg;
};
enum ath9k_int {
ATH9K_INT_RX = 0x00000001,
ATH9K_INT_RXDESC = 0x00000002,
ATH9K_INT_RXHP = 0x00000001,
ATH9K_INT_RXLP = 0x00000002,
ATH9K_INT_RXNOFRM = 0x00000008,
ATH9K_INT_RXEOL = 0x00000010,
ATH9K_INT_RXORN = 0x00000020,
ATH9K_INT_TX = 0x00000040,
ATH9K_INT_TXDESC = 0x00000080,
ATH9K_INT_TIM_TIMER = 0x00000100,
ATH9K_INT_MCI = 0x00000200,
ATH9K_INT_BB_WATCHDOG = 0x00000400,
ATH9K_INT_TXURN = 0x00000800,
ATH9K_INT_MIB = 0x00001000,
ATH9K_INT_RXPHY = 0x00004000,
ATH9K_INT_RXKCM = 0x00008000,
ATH9K_INT_SWBA = 0x00010000,
ATH9K_INT_BMISS = 0x00040000,
ATH9K_INT_BNR = 0x00100000,
ATH9K_INT_TIM = 0x00200000,
ATH9K_INT_DTIM = 0x00400000,
ATH9K_INT_DTIMSYNC = 0x00800000,
ATH9K_INT_GPIO = 0x01000000,
ATH9K_INT_CABEND = 0x02000000,
ATH9K_INT_TSFOOR = 0x04000000,
ATH9K_INT_GENTIMER = 0x08000000,
ATH9K_INT_CST = 0x10000000,
ATH9K_INT_GTT = 0x20000000,
ATH9K_INT_FATAL = 0x40000000,
ATH9K_INT_GLOBAL = 0x80000000,
ATH9K_INT_BMISC = ATH9K_INT_TIM |
ATH9K_INT_DTIM |
ATH9K_INT_DTIMSYNC |
ATH9K_INT_TSFOOR |
ATH9K_INT_CABEND,
ATH9K_INT_COMMON = ATH9K_INT_RXNOFRM |
ATH9K_INT_RXDESC |
ATH9K_INT_RXEOL |
ATH9K_INT_RXORN |
ATH9K_INT_TXURN |
ATH9K_INT_TXDESC |
ATH9K_INT_MIB |
ATH9K_INT_RXPHY |
ATH9K_INT_RXKCM |
ATH9K_INT_SWBA |
ATH9K_INT_BMISS |
ATH9K_INT_GPIO,
ATH9K_INT_NOCARD = 0xffffffff
};
#define CHANNEL_CCK 0x00020
#define CHANNEL_OFDM 0x00040
#define CHANNEL_2GHZ 0x00080
#define CHANNEL_5GHZ 0x00100
#define CHANNEL_PASSIVE 0x00200
#define CHANNEL_DYN 0x00400
#define CHANNEL_HALF 0x04000
#define CHANNEL_QUARTER 0x08000
#define CHANNEL_HT20 0x10000
#define CHANNEL_HT40PLUS 0x20000
#define CHANNEL_HT40MINUS 0x40000
#define CHANNEL_A (CHANNEL_5GHZ|CHANNEL_OFDM)
#define CHANNEL_B (CHANNEL_2GHZ|CHANNEL_CCK)
#define CHANNEL_G (CHANNEL_2GHZ|CHANNEL_OFDM)
#define CHANNEL_G_HT20 (CHANNEL_2GHZ|CHANNEL_HT20)
#define CHANNEL_A_HT20 (CHANNEL_5GHZ|CHANNEL_HT20)
#define CHANNEL_G_HT40PLUS (CHANNEL_2GHZ|CHANNEL_HT40PLUS)
#define CHANNEL_G_HT40MINUS (CHANNEL_2GHZ|CHANNEL_HT40MINUS)
#define CHANNEL_A_HT40PLUS (CHANNEL_5GHZ|CHANNEL_HT40PLUS)
#define CHANNEL_A_HT40MINUS (CHANNEL_5GHZ|CHANNEL_HT40MINUS)
#define CHANNEL_ALL \
(CHANNEL_OFDM| \
CHANNEL_CCK| \
CHANNEL_2GHZ | \
CHANNEL_5GHZ | \
CHANNEL_HT20 | \
CHANNEL_HT40PLUS | \
CHANNEL_HT40MINUS)
#define MAX_RTT_TABLE_ENTRY 6
#define MAX_IQCAL_MEASUREMENT 8
#define MAX_CL_TAB_ENTRY 16
#define CL_TAB_ENTRY(reg_base) (reg_base + (4 * j))
struct ath9k_hw_cal_data {
u16 channel;
u32 channelFlags;
u32 chanmode;
int32_t CalValid;
int8_t iCoff;
int8_t qCoff;
bool rtt_done;
bool paprd_packet_sent;
bool paprd_done;
bool nfcal_pending;
ath9k: use AP beacon miss as a trigger for fast recalibration When beacons get stuck in AP mode, the most likely cause is interference. Such interference can often go on for a while, and too many consecutive beacon misses can lead to connected clients getting dropped. Since connected clients might not be subjected to the same interference if that happens to be very local, the AP should try to deal with it as good as it can. One way to do this is to trigger an NF calibration with automatic baseband update right after the beacon miss. In my tests with very strong interference, this allowed the AP to continue transmitting beacons after only 2-3 misses, which allows a normal client to stay connected. With some of the newer - really sensitive - chips, the maximum noise floor limit is very low, which can be problematic during very strong interference. To avoid an endless loop of stuck beacons -> nfcal -> periodic calibration -> stuck beacons, the beacon miss event also sets a flag, which allows the calibration code to bypass the chip specific maximum NF value. This flag is automatically cleared, as soon as the first NF median goes back below the limits for all chains. In my tests, this allowed an ath9k AP to survive very strong interference (measured NF: -68, or sometimes even higher) without losing connectivity to its clients. Even under these conditions, I was able to transmit several mbits/s through the interface. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-02 21:53:14 +08:00
bool nfcal_interference;
bool done_txiqcal_once;
bool done_txclcal_once;
u16 small_signal_gain[AR9300_MAX_CHAINS];
u32 pa_table[AR9300_MAX_CHAINS][PAPRD_TABLE_SZ];
u32 num_measures[AR9300_MAX_CHAINS];
int tx_corr_coeff[MAX_IQCAL_MEASUREMENT][AR9300_MAX_CHAINS];
u32 tx_clcal[AR9300_MAX_CHAINS][MAX_CL_TAB_ENTRY];
u32 rtt_table[AR9300_MAX_CHAINS][MAX_RTT_TABLE_ENTRY];
struct ath9k_nfcal_hist nfCalHist[NUM_NF_READINGS];
};
struct ath9k_channel {
struct ieee80211_channel *chan;
u16 channel;
u32 channelFlags;
u32 chanmode;
s16 noisefloor;
};
#define IS_CHAN_G(_c) ((((_c)->channelFlags & (CHANNEL_G)) == CHANNEL_G) || \
(((_c)->channelFlags & CHANNEL_G_HT20) == CHANNEL_G_HT20) || \
(((_c)->channelFlags & CHANNEL_G_HT40PLUS) == CHANNEL_G_HT40PLUS) || \
(((_c)->channelFlags & CHANNEL_G_HT40MINUS) == CHANNEL_G_HT40MINUS))
#define IS_CHAN_OFDM(_c) (((_c)->channelFlags & CHANNEL_OFDM) != 0)
#define IS_CHAN_5GHZ(_c) (((_c)->channelFlags & CHANNEL_5GHZ) != 0)
#define IS_CHAN_2GHZ(_c) (((_c)->channelFlags & CHANNEL_2GHZ) != 0)
#define IS_CHAN_HALF_RATE(_c) (((_c)->channelFlags & CHANNEL_HALF) != 0)
#define IS_CHAN_QUARTER_RATE(_c) (((_c)->channelFlags & CHANNEL_QUARTER) != 0)
#define IS_CHAN_A_FAST_CLOCK(_ah, _c) \
((((_c)->channelFlags & CHANNEL_5GHZ) != 0) && \
((_ah)->caps.hw_caps & ATH9K_HW_CAP_FASTCLOCK))
/* These macros check chanmode and not channelFlags */
#define IS_CHAN_B(_c) ((_c)->chanmode == CHANNEL_B)
#define IS_CHAN_HT20(_c) (((_c)->chanmode == CHANNEL_A_HT20) || \
((_c)->chanmode == CHANNEL_G_HT20))
#define IS_CHAN_HT40(_c) (((_c)->chanmode == CHANNEL_A_HT40PLUS) || \
((_c)->chanmode == CHANNEL_A_HT40MINUS) || \
((_c)->chanmode == CHANNEL_G_HT40PLUS) || \
((_c)->chanmode == CHANNEL_G_HT40MINUS))
#define IS_CHAN_HT(_c) (IS_CHAN_HT20((_c)) || IS_CHAN_HT40((_c)))
enum ath9k_power_mode {
ATH9K_PM_AWAKE = 0,
ATH9K_PM_FULL_SLEEP,
ATH9K_PM_NETWORK_SLEEP,
ATH9K_PM_UNDEFINED
};
enum ser_reg_mode {
SER_REG_MODE_OFF = 0,
SER_REG_MODE_ON = 1,
SER_REG_MODE_AUTO = 2,
};
enum ath9k_rx_qtype {
ATH9K_RX_QUEUE_HP,
ATH9K_RX_QUEUE_LP,
ATH9K_RX_QUEUE_MAX,
};
struct ath9k_beacon_state {
u32 bs_nexttbtt;
u32 bs_nextdtim;
u32 bs_intval;
#define ATH9K_TSFOOR_THRESHOLD 0x00004240 /* 16k us */
u32 bs_dtimperiod;
u16 bs_cfpperiod;
u16 bs_cfpmaxduration;
u32 bs_cfpnext;
u16 bs_timoffset;
u16 bs_bmissthreshold;
u32 bs_sleepduration;
u32 bs_tsfoor_threshold;
};
struct chan_centers {
u16 synth_center;
u16 ctl_center;
u16 ext_center;
};
enum {
ATH9K_RESET_POWER_ON,
ATH9K_RESET_WARM,
ATH9K_RESET_COLD,
};
struct ath9k_hw_version {
u32 magic;
u16 devid;
u16 subvendorid;
u32 macVersion;
u16 macRev;
u16 phyRev;
u16 analog5GhzRev;
u16 analog2GhzRev;
enum ath_usb_dev usbdev;
};
/* Generic TSF timer definitions */
#define ATH_MAX_GEN_TIMER 16
#define AR_GENTMR_BIT(_index) (1 << (_index))
/*
* Using de Bruijin sequence to look up 1's index in a 32 bit number
* debruijn32 = 0000 0111 0111 1100 1011 0101 0011 0001
*/
#define debruijn32 0x077CB531U
struct ath_gen_timer_configuration {
u32 next_addr;
u32 period_addr;
u32 mode_addr;
u32 mode_mask;
};
struct ath_gen_timer {
void (*trigger)(void *arg);
void (*overflow)(void *arg);
void *arg;
u8 index;
};
struct ath_gen_timer_table {
u32 gen_timer_index[32];
struct ath_gen_timer *timers[ATH_MAX_GEN_TIMER];
union {
unsigned long timer_bits;
u16 val;
} timer_mask;
};
struct ath_hw_antcomb_conf {
u8 main_lna_conf;
u8 alt_lna_conf;
u8 fast_div_bias;
u8 main_gaintb;
u8 alt_gaintb;
int lna1_lna2_delta;
u8 div_group;
};
/**
* struct ath_hw_radar_conf - radar detection initialization parameters
*
* @pulse_inband: threshold for checking the ratio of in-band power
* to total power for short radar pulses (half dB steps)
* @pulse_inband_step: threshold for checking an in-band power to total
* power ratio increase for short radar pulses (half dB steps)
* @pulse_height: threshold for detecting the beginning of a short
* radar pulse (dB step)
* @pulse_rssi: threshold for detecting if a short radar pulse is
* gone (dB step)
* @pulse_maxlen: maximum pulse length (0.8 us steps)
*
* @radar_rssi: RSSI threshold for starting long radar detection (dB steps)
* @radar_inband: threshold for checking the ratio of in-band power
* to total power for long radar pulses (half dB steps)
* @fir_power: threshold for detecting the end of a long radar pulse (dB)
*
* @ext_channel: enable extension channel radar detection
*/
struct ath_hw_radar_conf {
unsigned int pulse_inband;
unsigned int pulse_inband_step;
unsigned int pulse_height;
unsigned int pulse_rssi;
unsigned int pulse_maxlen;
unsigned int radar_rssi;
unsigned int radar_inband;
int fir_power;
bool ext_channel;
};
/**
* struct ath_hw_private_ops - callbacks used internally by hardware code
*
* This structure contains private callbacks designed to only be used internally
* by the hardware core.
*
* @init_cal_settings: setup types of calibrations supported
* @init_cal: starts actual calibration
*
* @init_mode_gain_regs: Initialize TX/RX gain registers
*
* @rf_set_freq: change frequency
* @spur_mitigate_freq: spur mitigation
* @set_rf_regs:
* @compute_pll_control: compute the PLL control value to use for
* AR_RTC_PLL_CONTROL for a given channel
* @setup_calibration: set up calibration
* @iscal_supported: used to query if a type of calibration is supported
*
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
* @ani_cache_ini_regs: cache the values for ANI from the initial
* register settings through the register initialization.
*/
struct ath_hw_private_ops {
/* Calibration ops */
void (*init_cal_settings)(struct ath_hw *ah);
bool (*init_cal)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*init_mode_gain_regs)(struct ath_hw *ah);
void (*setup_calibration)(struct ath_hw *ah,
struct ath9k_cal_list *currCal);
/* PHY ops */
int (*rf_set_freq)(struct ath_hw *ah,
struct ath9k_channel *chan);
void (*spur_mitigate_freq)(struct ath_hw *ah,
struct ath9k_channel *chan);
bool (*set_rf_regs)(struct ath_hw *ah,
struct ath9k_channel *chan,
u16 modesIndex);
void (*set_channel_regs)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*init_bb)(struct ath_hw *ah,
struct ath9k_channel *chan);
int (*process_ini)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*olc_init)(struct ath_hw *ah);
void (*set_rfmode)(struct ath_hw *ah, struct ath9k_channel *chan);
void (*mark_phy_inactive)(struct ath_hw *ah);
void (*set_delta_slope)(struct ath_hw *ah, struct ath9k_channel *chan);
bool (*rfbus_req)(struct ath_hw *ah);
void (*rfbus_done)(struct ath_hw *ah);
void (*restore_chainmask)(struct ath_hw *ah);
u32 (*compute_pll_control)(struct ath_hw *ah,
struct ath9k_channel *chan);
bool (*ani_control)(struct ath_hw *ah, enum ath9k_ani_cmd cmd,
int param);
void (*do_getnf)(struct ath_hw *ah, int16_t nfarray[NUM_NF_READINGS]);
void (*set_radar_params)(struct ath_hw *ah,
struct ath_hw_radar_conf *conf);
int (*fast_chan_change)(struct ath_hw *ah, struct ath9k_channel *chan,
u8 *ini_reloaded);
/* ANI */
ath9k: add new ANI implementation for AR9003 This adds support for ANI for AR9003. The implementation for ANI for AR9003 is slightly different than the one used for the older chipset families. It can technically be used for the older families as well but this is not yet fully tested so we only enable the new ANI for the AR5008, AR9001 and AR9002 families with a module parameter, force_new_ani. The old ANI implementation is left intact. Details of the new ANI implemention: * ANI adjustment logic is now table driven so that each ANI level setting is parameterized. This makes adjustments much more deterministic than the old procedure based logic and allows adjustments to be made incrementally to several parameters per level. * ANI register settings are now relative to INI values; so ANI param zero level == INI value. Appropriate floor and ceiling values are obeyed when adjustments are combined with INI values. * ANI processing is done once per second rather that every 100ms. The poll interval is now a set upon hardware initialization and can be picked up by the core driver. * OFDM error and CCK error processing are made in a round robin fashion rather than allowing all OFDM adjustments to be made before CCK adjustments. * ANI adjusts MRC CCK off in the presence of high CCK errors * When adjusting spur immunity (SI) and OFDM weak signal detection, ANI now sets register values for the extension channel too * When adjusting FIR step (ST), ANI now sets register for FIR step low too * FIR step adjustments now allow for an extra level of immunity for extremely noisy environments * The old Noise immunity setting (NI), which changes coarse low, size desired, etc have been removed. Changing these settings could affect up RIFS RX as well. * CCK weak signal adjustment is no longer used * ANI no longer enables phy error interrupts; in all cases phy hw counting registers are used instead * The phy error count (overflow) interrupts are also no longer used for ANI adjustments. All ANI adjustments are made via the polling routine and no adjustments are possible in the ISR context anymore * A history settings buffer is now correctly used for each channel; channel settings are initialized with the defaults but later changes are restored when returning back to that channel * When scanning, ANI is disabled settings are returned to (INI) defaults. * OFDM phy error thresholds are now 400 & 1000 (errors/second units) for low/high water marks, providing increased stability/hysteresis when changing levels. * Similarly CCK phy error thresholds are now 300 & 600 (errors/second) Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-12 12:33:45 +08:00
void (*ani_cache_ini_regs)(struct ath_hw *ah);
};
/**
* struct ath_spec_scan - parameters for Atheros spectral scan
*
* @enabled: enable/disable spectral scan
* @short_repeat: controls whether the chip is in spectral scan mode
* for 4 usec (enabled) or 204 usec (disabled)
* @count: number of scan results requested. There are special meanings
* in some chip revisions:
* AR92xx: highest bit set (>=128) for endless mode
* (spectral scan won't stopped until explicitly disabled)
* AR9300 and newer: 0 for endless mode
* @endless: true if endless mode is intended. Otherwise, count value is
* corrected to the next possible value.
* @period: time duration between successive spectral scan entry points
* (period*256*Tclk). Tclk = ath_common->clockrate
* @fft_period: PHY passes FFT frames to MAC every (fft_period+1)*4uS
*
* Note: Tclk = 40MHz or 44MHz depending upon operating mode.
* Typically it's 44MHz in 2/5GHz on later chips, but there's
* a "fast clock" check for this in 5GHz.
*
*/
struct ath_spec_scan {
bool enabled;
bool short_repeat;
bool endless;
u8 count;
u8 period;
u8 fft_period;
};
/**
* struct ath_hw_ops - callbacks used by hardware code and driver code
*
* This structure contains callbacks designed to to be used internally by
* hardware code and also by the lower level driver.
*
* @config_pci_powersave:
* @calibrate: periodic calibration for NF, ANI, IQ, ADC gain, ADC-DC
*
* @spectral_scan_config: set parameters for spectral scan and enable/disable it
* @spectral_scan_trigger: trigger a spectral scan run
* @spectral_scan_wait: wait for a spectral scan run to finish
*/
struct ath_hw_ops {
void (*config_pci_powersave)(struct ath_hw *ah,
bool power_off);
void (*rx_enable)(struct ath_hw *ah);
void (*set_desc_link)(void *ds, u32 link);
bool (*calibrate)(struct ath_hw *ah,
struct ath9k_channel *chan,
u8 rxchainmask,
bool longcal);
bool (*get_isr)(struct ath_hw *ah, enum ath9k_int *masked);
void (*set_txdesc)(struct ath_hw *ah, void *ds,
struct ath_tx_info *i);
int (*proc_txdesc)(struct ath_hw *ah, void *ds,
struct ath_tx_status *ts);
void (*antdiv_comb_conf_get)(struct ath_hw *ah,
struct ath_hw_antcomb_conf *antconf);
void (*antdiv_comb_conf_set)(struct ath_hw *ah,
struct ath_hw_antcomb_conf *antconf);
void (*antctrl_shared_chain_lnadiv)(struct ath_hw *hw, bool enable);
void (*spectral_scan_config)(struct ath_hw *ah,
struct ath_spec_scan *param);
void (*spectral_scan_trigger)(struct ath_hw *ah);
void (*spectral_scan_wait)(struct ath_hw *ah);
};
struct ath_nf_limits {
s16 max;
s16 min;
s16 nominal;
};
enum ath_cal_list {
TX_IQ_CAL = BIT(0),
TX_IQ_ON_AGC_CAL = BIT(1),
TX_CL_CAL = BIT(2),
};
/* ah_flags */
#define AH_USE_EEPROM 0x1
#define AH_UNPLUGGED 0x2 /* The card has been physically removed. */
#define AH_FASTCC 0x4
struct ath_hw {
struct ath_ops reg_ops;
struct device *dev;
struct ieee80211_hw *hw;
struct ath_common common;
struct ath9k_hw_version hw_version;
struct ath9k_ops_config config;
struct ath9k_hw_capabilities caps;
struct ath9k_channel channels[ATH9K_NUM_CHANNELS];
struct ath9k_channel *curchan;
union {
struct ar5416_eeprom_def def;
struct ar5416_eeprom_4k map4k;
struct ar9287_eeprom map9287;
struct ar9300_eeprom ar9300_eep;
} eeprom;
const struct eeprom_ops *eep_ops;
bool sw_mgmt_crypto;
bool is_pciexpress;
bool aspm_enabled;
bool is_monitoring;
bool need_an_top2_fixup;
bool shared_chain_lnadiv;
u16 tx_trig_level;
u32 nf_regs[6];
struct ath_nf_limits nf_2g;
struct ath_nf_limits nf_5g;
u16 rfsilent;
u32 rfkill_gpio;
u32 rfkill_polarity;
u32 ah_flags;
bool reset_power_on;
bool htc_reset_init;
enum nl80211_iftype opmode;
enum ath9k_power_mode power_mode;
s8 noise;
struct ath9k_hw_cal_data *caldata;
struct ath9k_pacal_info pacal_info;
struct ar5416Stats stats;
struct ath9k_tx_queue_info txq[ATH9K_NUM_TX_QUEUES];
enum ath9k_int imask;
u32 imrs2_reg;
u32 txok_interrupt_mask;
u32 txerr_interrupt_mask;
u32 txdesc_interrupt_mask;
u32 txeol_interrupt_mask;
u32 txurn_interrupt_mask;
atomic_t intr_ref_cnt;
bool chip_fullsleep;
u32 atim_window;
u32 modes_index;
/* Calibration */
u32 supp_cals;
struct ath9k_cal_list iq_caldata;
struct ath9k_cal_list adcgain_caldata;
struct ath9k_cal_list adcdc_caldata;
struct ath9k_cal_list *cal_list;
struct ath9k_cal_list *cal_list_last;
struct ath9k_cal_list *cal_list_curr;
#define totalPowerMeasI meas0.unsign
#define totalPowerMeasQ meas1.unsign
#define totalIqCorrMeas meas2.sign
#define totalAdcIOddPhase meas0.unsign
#define totalAdcIEvenPhase meas1.unsign
#define totalAdcQOddPhase meas2.unsign
#define totalAdcQEvenPhase meas3.unsign
#define totalAdcDcOffsetIOddPhase meas0.sign
#define totalAdcDcOffsetIEvenPhase meas1.sign
#define totalAdcDcOffsetQOddPhase meas2.sign
#define totalAdcDcOffsetQEvenPhase meas3.sign
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas0;
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas1;
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas2;
union {
u32 unsign[AR5416_MAX_CHAINS];
int32_t sign[AR5416_MAX_CHAINS];
} meas3;
u16 cal_samples;
u8 enabled_cals;
u32 sta_id1_defaults;
u32 misc_mode;
/* Private to hardware code */
struct ath_hw_private_ops private_ops;
/* Accessed by the lower level driver */
struct ath_hw_ops ops;
/* Used to program the radio on non single-chip devices */
u32 *analogBank6Data;
int coverage_class;
u32 slottime;
u32 globaltxtimeout;
/* ANI */
u32 aniperiod;
enum ath9k_ani_cmd ani_function;
u32 ani_skip_count;
struct ar5416AniState ani;
#ifdef CONFIG_ATH9K_BTCOEX_SUPPORT
struct ath_btcoex_hw btcoex_hw;
#endif
u32 intr_txqs;
u8 txchainmask;
u8 rxchainmask;
struct ath_hw_radar_conf radar_conf;
u32 originalGain[22];
int initPDADC;
int PDADCdelta;
int led_pin;
u32 gpio_mask;
u32 gpio_val;
struct ar5416IniArray iniModes;
struct ar5416IniArray iniCommon;
struct ar5416IniArray iniBB_RfGain;
struct ar5416IniArray iniBank6;
struct ar5416IniArray iniAddac;
struct ar5416IniArray iniPcieSerdes;
struct ar5416IniArray iniPcieSerdesLowPower;
struct ar5416IniArray iniModesFastClock;
struct ar5416IniArray iniAdditional;
struct ar5416IniArray iniModesRxGain;
struct ar5416IniArray ini_modes_rx_gain_bounds;
struct ar5416IniArray iniModesTxGain;
struct ar5416IniArray iniCckfirNormal;
struct ar5416IniArray iniCckfirJapan2484;
struct ar5416IniArray iniModes_9271_ANI_reg;
struct ar5416IniArray ini_radio_post_sys2ant;
struct ar5416IniArray ini_modes_rxgain_5g_xlna;
struct ar5416IniArray iniMac[ATH_INI_NUM_SPLIT];
struct ar5416IniArray iniBB[ATH_INI_NUM_SPLIT];
struct ar5416IniArray iniRadio[ATH_INI_NUM_SPLIT];
struct ar5416IniArray iniSOC[ATH_INI_NUM_SPLIT];
u32 intr_gen_timer_trigger;
u32 intr_gen_timer_thresh;
struct ath_gen_timer_table hw_gen_timers;
struct ar9003_txs *ts_ring;
u32 ts_paddr_start;
u32 ts_paddr_end;
u16 ts_tail;
u16 ts_size;
u32 bb_watchdog_last_status;
u32 bb_watchdog_timeout_ms; /* in ms, 0 to disable */
u8 bb_hang_rx_ofdm; /* true if bb hang due to rx_ofdm */
unsigned int paprd_target_power;
unsigned int paprd_training_power;
unsigned int paprd_ratemask;
unsigned int paprd_ratemask_ht40;
bool paprd_table_write_done;
u32 paprd_gain_table_entries[PAPRD_GAIN_TABLE_ENTRIES];
u8 paprd_gain_table_index[PAPRD_GAIN_TABLE_ENTRIES];
/*
* Store the permanent value of Reg 0x4004in WARegVal
* so we dont have to R/M/W. We should not be reading
* this register when in sleep states.
*/
u32 WARegVal;
/* Enterprise mode cap */
u32 ent_mode;
#ifdef CONFIG_PM_SLEEP
u32 wow_event_mask;
#endif
bool is_clk_25mhz;
int (*get_mac_revision)(void);
int (*external_reset)(void);
const struct firmware *eeprom_blob;
};
struct ath_bus_ops {
enum ath_bus_type ath_bus_type;
void (*read_cachesize)(struct ath_common *common, int *csz);
bool (*eeprom_read)(struct ath_common *common, u32 off, u16 *data);
void (*bt_coex_prep)(struct ath_common *common);
void (*aspm_init)(struct ath_common *common);
};
static inline struct ath_common *ath9k_hw_common(struct ath_hw *ah)
{
return &ah->common;
}
static inline struct ath_regulatory *ath9k_hw_regulatory(struct ath_hw *ah)
{
return &(ath9k_hw_common(ah)->regulatory);
}
static inline struct ath_hw_private_ops *ath9k_hw_private_ops(struct ath_hw *ah)
{
return &ah->private_ops;
}
static inline struct ath_hw_ops *ath9k_hw_ops(struct ath_hw *ah)
{
return &ah->ops;
}
static inline u8 get_streams(int mask)
{
return !!(mask & BIT(0)) + !!(mask & BIT(1)) + !!(mask & BIT(2));
}
/* Initialization, Detach, Reset */
void ath9k_hw_deinit(struct ath_hw *ah);
int ath9k_hw_init(struct ath_hw *ah);
int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,
struct ath9k_hw_cal_data *caldata, bool fastcc);
int ath9k_hw_fill_cap_info(struct ath_hw *ah);
u32 ath9k_regd_get_ctl(struct ath_regulatory *reg, struct ath9k_channel *chan);
/* GPIO / RFKILL / Antennae */
void ath9k_hw_cfg_gpio_input(struct ath_hw *ah, u32 gpio);
u32 ath9k_hw_gpio_get(struct ath_hw *ah, u32 gpio);
void ath9k_hw_cfg_output(struct ath_hw *ah, u32 gpio,
u32 ah_signal_type);
void ath9k_hw_set_gpio(struct ath_hw *ah, u32 gpio, u32 val);
void ath9k_hw_setantenna(struct ath_hw *ah, u32 antenna);
/* General Operation */
void ath9k_hw_synth_delay(struct ath_hw *ah, struct ath9k_channel *chan,
int hw_delay);
bool ath9k_hw_wait(struct ath_hw *ah, u32 reg, u32 mask, u32 val, u32 timeout);
void ath9k_hw_write_array(struct ath_hw *ah, const struct ar5416IniArray *array,
int column, unsigned int *writecnt);
u32 ath9k_hw_reverse_bits(u32 val, u32 n);
u16 ath9k_hw_computetxtime(struct ath_hw *ah,
u8 phy, int kbps,
u32 frameLen, u16 rateix, bool shortPreamble);
void ath9k_hw_get_channel_centers(struct ath_hw *ah,
struct ath9k_channel *chan,
struct chan_centers *centers);
u32 ath9k_hw_getrxfilter(struct ath_hw *ah);
void ath9k_hw_setrxfilter(struct ath_hw *ah, u32 bits);
bool ath9k_hw_phy_disable(struct ath_hw *ah);
bool ath9k_hw_disable(struct ath_hw *ah);
void ath9k_hw_set_txpowerlimit(struct ath_hw *ah, u32 limit, bool test);
void ath9k_hw_setopmode(struct ath_hw *ah);
void ath9k_hw_setmcastfilter(struct ath_hw *ah, u32 filter0, u32 filter1);
void ath9k_hw_write_associd(struct ath_hw *ah);
u32 ath9k_hw_gettsf32(struct ath_hw *ah);
u64 ath9k_hw_gettsf64(struct ath_hw *ah);
void ath9k_hw_settsf64(struct ath_hw *ah, u64 tsf64);
void ath9k_hw_reset_tsf(struct ath_hw *ah);
void ath9k_hw_set_tsfadjust(struct ath_hw *ah, bool set);
void ath9k_hw_init_global_settings(struct ath_hw *ah);
u32 ar9003_get_pll_sqsum_dvc(struct ath_hw *ah);
void ath9k_hw_set11nmac2040(struct ath_hw *ah);
void ath9k_hw_beaconinit(struct ath_hw *ah, u32 next_beacon, u32 beacon_period);
void ath9k_hw_set_sta_beacon_timers(struct ath_hw *ah,
const struct ath9k_beacon_state *bs);
bool ath9k_hw_check_alive(struct ath_hw *ah);
bool ath9k_hw_setpower(struct ath_hw *ah, enum ath9k_power_mode mode);
#ifdef CONFIG_ATH9K_DEBUGFS
void ath9k_debug_sync_cause(struct ath_common *common, u32 sync_cause);
#else
static inline void ath9k_debug_sync_cause(struct ath_common *common,
u32 sync_cause) {}
#endif
/* Generic hw timer primitives */
struct ath_gen_timer *ath_gen_timer_alloc(struct ath_hw *ah,
void (*trigger)(void *),
void (*overflow)(void *),
void *arg,
u8 timer_index);
void ath9k_hw_gen_timer_start(struct ath_hw *ah,
struct ath_gen_timer *timer,
u32 timer_next,
u32 timer_period);
void ath9k_hw_gen_timer_stop(struct ath_hw *ah, struct ath_gen_timer *timer);
void ath_gen_timer_free(struct ath_hw *ah, struct ath_gen_timer *timer);
void ath_gen_timer_isr(struct ath_hw *hw);
void ath9k_hw_name(struct ath_hw *ah, char *hw_name, size_t len);
/* PHY */
void ath9k_hw_get_delta_slope_vals(struct ath_hw *ah, u32 coef_scaled,
u32 *coef_mantissa, u32 *coef_exponent);
void ath9k_hw_apply_txpower(struct ath_hw *ah, struct ath9k_channel *chan,
bool test);
/*
* Code Specific to AR5008, AR9001 or AR9002,
* we stuff these here to avoid callbacks for AR9003.
*/
int ar9002_hw_rf_claim(struct ath_hw *ah);
void ar9002_hw_enable_async_fifo(struct ath_hw *ah);
/*
* Code specific to AR9003, we stuff these here to avoid callbacks
* for older families
*/
void ar9003_hw_bb_watchdog_config(struct ath_hw *ah);
void ar9003_hw_bb_watchdog_read(struct ath_hw *ah);
void ar9003_hw_bb_watchdog_dbg_info(struct ath_hw *ah);
void ar9003_hw_disable_phy_restart(struct ath_hw *ah);
void ar9003_paprd_enable(struct ath_hw *ah, bool val);
void ar9003_paprd_populate_single_table(struct ath_hw *ah,
struct ath9k_hw_cal_data *caldata,
int chain);
int ar9003_paprd_create_curve(struct ath_hw *ah,
struct ath9k_hw_cal_data *caldata, int chain);
void ar9003_paprd_setup_gain_table(struct ath_hw *ah, int chain);
int ar9003_paprd_init_table(struct ath_hw *ah);
bool ar9003_paprd_is_done(struct ath_hw *ah);
bool ar9003_is_paprd_enabled(struct ath_hw *ah);
void ar9003_hw_set_chain_masks(struct ath_hw *ah, u8 rx, u8 tx);
/* Hardware family op attach helpers */
int ar5008_hw_attach_phy_ops(struct ath_hw *ah);
void ar9002_hw_attach_phy_ops(struct ath_hw *ah);
void ar9003_hw_attach_phy_ops(struct ath_hw *ah);
void ar9002_hw_attach_calib_ops(struct ath_hw *ah);
void ar9003_hw_attach_calib_ops(struct ath_hw *ah);
int ar9002_hw_attach_ops(struct ath_hw *ah);
void ar9003_hw_attach_ops(struct ath_hw *ah);
void ar9002_hw_load_ani_reg(struct ath_hw *ah, struct ath9k_channel *chan);
void ath9k_ani_reset(struct ath_hw *ah, bool is_scanning);
void ath9k_hw_ani_monitor(struct ath_hw *ah, struct ath9k_channel *chan);
#ifdef CONFIG_ATH9K_BTCOEX_SUPPORT
static inline bool ath9k_hw_btcoex_is_enabled(struct ath_hw *ah)
{
return ah->btcoex_hw.enabled;
}
static inline bool ath9k_hw_mci_is_enabled(struct ath_hw *ah)
{
return ah->common.btcoex_enabled &&
(ah->caps.hw_caps & ATH9K_HW_CAP_MCI);
}
void ath9k_hw_btcoex_enable(struct ath_hw *ah);
static inline enum ath_btcoex_scheme
ath9k_hw_get_btcoex_scheme(struct ath_hw *ah)
{
return ah->btcoex_hw.scheme;
}
#else
static inline bool ath9k_hw_btcoex_is_enabled(struct ath_hw *ah)
{
return false;
}
static inline bool ath9k_hw_mci_is_enabled(struct ath_hw *ah)
{
return false;
}
static inline void ath9k_hw_btcoex_enable(struct ath_hw *ah)
{
}
static inline enum ath_btcoex_scheme
ath9k_hw_get_btcoex_scheme(struct ath_hw *ah)
{
return ATH_BTCOEX_CFG_NONE;
}
#endif /* CONFIG_ATH9K_BTCOEX_SUPPORT */
#ifdef CONFIG_PM_SLEEP
const char *ath9k_hw_wow_event_to_string(u32 wow_event);
void ath9k_hw_wow_apply_pattern(struct ath_hw *ah, u8 *user_pattern,
u8 *user_mask, int pattern_count,
int pattern_len);
u32 ath9k_hw_wow_wakeup(struct ath_hw *ah);
void ath9k_hw_wow_enable(struct ath_hw *ah, u32 pattern_enable);
#else
static inline const char *ath9k_hw_wow_event_to_string(u32 wow_event)
{
return NULL;
}
static inline void ath9k_hw_wow_apply_pattern(struct ath_hw *ah,
u8 *user_pattern,
u8 *user_mask,
int pattern_count,
int pattern_len)
{
}
static inline u32 ath9k_hw_wow_wakeup(struct ath_hw *ah)
{
return 0;
}
static inline void ath9k_hw_wow_enable(struct ath_hw *ah, u32 pattern_enable)
{
}
#endif
#define ATH9K_CLOCK_RATE_CCK 22
#define ATH9K_CLOCK_RATE_5GHZ_OFDM 40
#define ATH9K_CLOCK_RATE_2GHZ_OFDM 44
#define ATH9K_CLOCK_FAST_RATE_5GHZ_OFDM 44
#endif