OpenCloudOS-Kernel/drivers/net/wireless/ath/ath5k/debug.c

541 lines
15 KiB
C
Raw Normal View History

/*
* Copyright (c) 2007-2008 Bruno Randolf <bruno@thinktube.com>
*
* This file is free software: you may copy, redistribute and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation, either version 2 of the License, or (at your
* option) any later version.
*
* This file is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*
* This file incorporates work covered by the following copyright and
* permission notice:
*
* Copyright (c) 2002-2005 Sam Leffler, Errno Consulting
* Copyright (c) 2004-2005 Atheros Communications, Inc.
* Copyright (c) 2006 Devicescape Software, Inc.
* Copyright (c) 2007 Jiri Slaby <jirislaby@gmail.com>
* Copyright (c) 2007 Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
*
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
* redistribution must be conditioned upon including a substantially
* similar Disclaimer requirement for further binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
* AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
* THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
* OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
* IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGES.
*/
#include "base.h"
#include "debug.h"
static unsigned int ath5k_debug;
module_param_named(debug, ath5k_debug, uint, 0);
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
#ifdef CONFIG_ATH5K_DEBUG
#include <linux/seq_file.h>
#include "reg.h"
static struct dentry *ath5k_global_debugfs;
static int ath5k_debugfs_open(struct inode *inode, struct file *file)
{
file->private_data = inode->i_private;
return 0;
}
/* debugfs: registers */
struct reg {
const char *name;
int addr;
};
#define REG_STRUCT_INIT(r) { #r, r }
/* just a few random registers, might want to add more */
static const struct reg regs[] = {
REG_STRUCT_INIT(AR5K_CR),
REG_STRUCT_INIT(AR5K_RXDP),
REG_STRUCT_INIT(AR5K_CFG),
REG_STRUCT_INIT(AR5K_IER),
REG_STRUCT_INIT(AR5K_BCR),
REG_STRUCT_INIT(AR5K_RTSD0),
REG_STRUCT_INIT(AR5K_RTSD1),
REG_STRUCT_INIT(AR5K_TXCFG),
REG_STRUCT_INIT(AR5K_RXCFG),
REG_STRUCT_INIT(AR5K_RXJLA),
REG_STRUCT_INIT(AR5K_MIBC),
REG_STRUCT_INIT(AR5K_TOPS),
REG_STRUCT_INIT(AR5K_RXNOFRM),
REG_STRUCT_INIT(AR5K_TXNOFRM),
REG_STRUCT_INIT(AR5K_RPGTO),
REG_STRUCT_INIT(AR5K_RFCNT),
REG_STRUCT_INIT(AR5K_MISC),
REG_STRUCT_INIT(AR5K_QCUDCU_CLKGT),
REG_STRUCT_INIT(AR5K_ISR),
REG_STRUCT_INIT(AR5K_PISR),
REG_STRUCT_INIT(AR5K_SISR0),
REG_STRUCT_INIT(AR5K_SISR1),
REG_STRUCT_INIT(AR5K_SISR2),
REG_STRUCT_INIT(AR5K_SISR3),
REG_STRUCT_INIT(AR5K_SISR4),
REG_STRUCT_INIT(AR5K_IMR),
REG_STRUCT_INIT(AR5K_PIMR),
REG_STRUCT_INIT(AR5K_SIMR0),
REG_STRUCT_INIT(AR5K_SIMR1),
REG_STRUCT_INIT(AR5K_SIMR2),
REG_STRUCT_INIT(AR5K_SIMR3),
REG_STRUCT_INIT(AR5K_SIMR4),
REG_STRUCT_INIT(AR5K_DCM_ADDR),
REG_STRUCT_INIT(AR5K_DCCFG),
REG_STRUCT_INIT(AR5K_CCFG),
REG_STRUCT_INIT(AR5K_CPC0),
REG_STRUCT_INIT(AR5K_CPC1),
REG_STRUCT_INIT(AR5K_CPC2),
REG_STRUCT_INIT(AR5K_CPC3),
REG_STRUCT_INIT(AR5K_CPCOVF),
REG_STRUCT_INIT(AR5K_RESET_CTL),
REG_STRUCT_INIT(AR5K_SLEEP_CTL),
REG_STRUCT_INIT(AR5K_INTPEND),
REG_STRUCT_INIT(AR5K_SFR),
REG_STRUCT_INIT(AR5K_PCICFG),
REG_STRUCT_INIT(AR5K_GPIOCR),
REG_STRUCT_INIT(AR5K_GPIODO),
REG_STRUCT_INIT(AR5K_SREV),
};
static void *reg_start(struct seq_file *seq, loff_t *pos)
{
return *pos < ARRAY_SIZE(regs) ? (void *)&regs[*pos] : NULL;
}
static void reg_stop(struct seq_file *seq, void *p)
{
/* nothing to do */
}
static void *reg_next(struct seq_file *seq, void *p, loff_t *pos)
{
++*pos;
return *pos < ARRAY_SIZE(regs) ? (void *)&regs[*pos] : NULL;
}
static int reg_show(struct seq_file *seq, void *p)
{
struct ath5k_softc *sc = seq->private;
struct reg *r = p;
seq_printf(seq, "%-25s0x%08x\n", r->name,
ath5k_hw_reg_read(sc->ah, r->addr));
return 0;
}
static const struct seq_operations register_seq_ops = {
.start = reg_start,
.next = reg_next,
.stop = reg_stop,
.show = reg_show
};
static int open_file_registers(struct inode *inode, struct file *file)
{
struct seq_file *s;
int res;
res = seq_open(file, &register_seq_ops);
if (res == 0) {
s = file->private_data;
s->private = inode->i_private;
}
return res;
}
static const struct file_operations fops_registers = {
.open = open_file_registers,
.read = seq_read,
.llseek = seq_lseek,
.release = seq_release,
.owner = THIS_MODULE,
};
/* debugfs: beacons */
static ssize_t read_file_beacon(struct file *file, char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath5k_softc *sc = file->private_data;
struct ath5k_hw *ah = sc->ah;
char buf[500];
unsigned int len = 0;
unsigned int v;
u64 tsf;
v = ath5k_hw_reg_read(sc->ah, AR5K_BEACON);
len += snprintf(buf+len, sizeof(buf)-len,
"%-24s0x%08x\tintval: %d\tTIM: 0x%x\n",
"AR5K_BEACON", v, v & AR5K_BEACON_PERIOD,
(v & AR5K_BEACON_TIM) >> AR5K_BEACON_TIM_S);
len += snprintf(buf+len, sizeof(buf)-len, "%-24s0x%08x\n",
"AR5K_LAST_TSTP", ath5k_hw_reg_read(sc->ah, AR5K_LAST_TSTP));
len += snprintf(buf+len, sizeof(buf)-len, "%-24s0x%08x\n\n",
"AR5K_BEACON_CNT", ath5k_hw_reg_read(sc->ah, AR5K_BEACON_CNT));
v = ath5k_hw_reg_read(sc->ah, AR5K_TIMER0);
len += snprintf(buf+len, sizeof(buf)-len, "%-24s0x%08x\tTU: %08x\n",
"AR5K_TIMER0 (TBTT)", v, v);
v = ath5k_hw_reg_read(sc->ah, AR5K_TIMER1);
len += snprintf(buf+len, sizeof(buf)-len, "%-24s0x%08x\tTU: %08x\n",
"AR5K_TIMER1 (DMA)", v, v >> 3);
v = ath5k_hw_reg_read(sc->ah, AR5K_TIMER2);
len += snprintf(buf+len, sizeof(buf)-len, "%-24s0x%08x\tTU: %08x\n",
"AR5K_TIMER2 (SWBA)", v, v >> 3);
v = ath5k_hw_reg_read(sc->ah, AR5K_TIMER3);
len += snprintf(buf+len, sizeof(buf)-len, "%-24s0x%08x\tTU: %08x\n",
"AR5K_TIMER3 (ATIM)", v, v);
tsf = ath5k_hw_get_tsf64(sc->ah);
len += snprintf(buf+len, sizeof(buf)-len,
wireless: correct warnings from using '%llx' for type 'u64' drivers/net/wireless/ath5k/debug.c: In function 'read_file_tsf': drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c:203: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c: In function 'read_file_beacon': drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/ath5k/debug.c:274: warning: format '%016llx' expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_tx_status_reply_compressed_ba': drivers/net/wireless/iwlwifi/iwl-4965.c:3907: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64' drivers/net/wireless/iwlwifi/iwl-4965.c: In function 'iwl4965_rx_reply_compressed_ba': drivers/net/wireless/iwlwifi/iwl-4965.c:4039: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type '__le64' drivers/net/wireless/iwlwifi/iwl-4965.c:4046: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64' drivers/net/wireless/iwlwifi/iwl4965-base.c: In function 'iwl4965_tx_status_reply_tx': drivers/net/wireless/iwlwifi/iwl4965-base.c:3661: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64' Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-03-08 05:38:43 +08:00
"TSF\t\t0x%016llx\tTU: %08x\n",
(unsigned long long)tsf, TSF_TO_TU(tsf));
return simple_read_from_buffer(user_buf, count, ppos, buf, len);
}
static ssize_t write_file_beacon(struct file *file,
const char __user *userbuf,
size_t count, loff_t *ppos)
{
struct ath5k_softc *sc = file->private_data;
struct ath5k_hw *ah = sc->ah;
char buf[20];
if (copy_from_user(buf, userbuf, min(count, sizeof(buf))))
return -EFAULT;
if (strncmp(buf, "disable", 7) == 0) {
AR5K_REG_DISABLE_BITS(ah, AR5K_BEACON, AR5K_BEACON_ENABLE);
printk(KERN_INFO "debugfs disable beacons\n");
} else if (strncmp(buf, "enable", 6) == 0) {
AR5K_REG_ENABLE_BITS(ah, AR5K_BEACON, AR5K_BEACON_ENABLE);
printk(KERN_INFO "debugfs enable beacons\n");
}
return count;
}
static const struct file_operations fops_beacon = {
.read = read_file_beacon,
.write = write_file_beacon,
.open = ath5k_debugfs_open,
.owner = THIS_MODULE,
};
/* debugfs: reset */
static ssize_t write_file_reset(struct file *file,
const char __user *userbuf,
size_t count, loff_t *ppos)
{
struct ath5k_softc *sc = file->private_data;
tasklet_schedule(&sc->restq);
return count;
}
static const struct file_operations fops_reset = {
.write = write_file_reset,
.open = ath5k_debugfs_open,
.owner = THIS_MODULE,
};
/* debugfs: debug level */
static const struct {
enum ath5k_debug_level level;
const char *name;
const char *desc;
} dbg_info[] = {
{ ATH5K_DEBUG_RESET, "reset", "reset and initialization" },
{ ATH5K_DEBUG_INTR, "intr", "interrupt handling" },
{ ATH5K_DEBUG_MODE, "mode", "mode init/setup" },
{ ATH5K_DEBUG_XMIT, "xmit", "basic xmit operation" },
{ ATH5K_DEBUG_BEACON, "beacon", "beacon handling" },
{ ATH5K_DEBUG_CALIBRATE, "calib", "periodic calibration" },
{ ATH5K_DEBUG_TXPOWER, "txpower", "transmit power setting" },
{ ATH5K_DEBUG_LED, "led", "LED management" },
{ ATH5K_DEBUG_DUMP_RX, "dumprx", "print received skb content" },
{ ATH5K_DEBUG_DUMP_TX, "dumptx", "print transmit skb content" },
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
{ ATH5K_DEBUG_DUMPBANDS, "dumpbands", "dump bands" },
{ ATH5K_DEBUG_TRACE, "trace", "trace function calls" },
{ ATH5K_DEBUG_ANY, "all", "show all debug levels" },
};
static ssize_t read_file_debug(struct file *file, char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath5k_softc *sc = file->private_data;
char buf[700];
unsigned int len = 0;
unsigned int i;
len += snprintf(buf+len, sizeof(buf)-len,
"DEBUG LEVEL: 0x%08x\n\n", sc->debug.level);
for (i = 0; i < ARRAY_SIZE(dbg_info) - 1; i++) {
len += snprintf(buf+len, sizeof(buf)-len,
"%10s %c 0x%08x - %s\n", dbg_info[i].name,
sc->debug.level & dbg_info[i].level ? '+' : ' ',
dbg_info[i].level, dbg_info[i].desc);
}
len += snprintf(buf+len, sizeof(buf)-len,
"%10s %c 0x%08x - %s\n", dbg_info[i].name,
sc->debug.level == dbg_info[i].level ? '+' : ' ',
dbg_info[i].level, dbg_info[i].desc);
return simple_read_from_buffer(user_buf, count, ppos, buf, len);
}
static ssize_t write_file_debug(struct file *file,
const char __user *userbuf,
size_t count, loff_t *ppos)
{
struct ath5k_softc *sc = file->private_data;
unsigned int i;
char buf[20];
if (copy_from_user(buf, userbuf, min(count, sizeof(buf))))
return -EFAULT;
for (i = 0; i < ARRAY_SIZE(dbg_info); i++) {
if (strncmp(buf, dbg_info[i].name,
strlen(dbg_info[i].name)) == 0) {
sc->debug.level ^= dbg_info[i].level; /* toggle bit */
break;
}
}
return count;
}
static const struct file_operations fops_debug = {
.read = read_file_debug,
.write = write_file_debug,
.open = ath5k_debugfs_open,
.owner = THIS_MODULE,
};
/* init */
void
ath5k_debug_init(void)
{
ath5k_global_debugfs = debugfs_create_dir("ath5k", NULL);
}
void
ath5k_debug_init_device(struct ath5k_softc *sc)
{
sc->debug.level = ath5k_debug;
sc->debug.debugfs_phydir = debugfs_create_dir(wiphy_name(sc->hw->wiphy),
ath5k_global_debugfs);
sc->debug.debugfs_debug = debugfs_create_file("debug",
S_IWUSR | S_IRUSR,
sc->debug.debugfs_phydir, sc, &fops_debug);
sc->debug.debugfs_registers = debugfs_create_file("registers", S_IRUSR,
sc->debug.debugfs_phydir, sc, &fops_registers);
sc->debug.debugfs_beacon = debugfs_create_file("beacon",
S_IWUSR | S_IRUSR,
sc->debug.debugfs_phydir, sc, &fops_beacon);
sc->debug.debugfs_reset = debugfs_create_file("reset", S_IWUSR,
sc->debug.debugfs_phydir, sc, &fops_reset);
}
void
ath5k_debug_finish(void)
{
debugfs_remove(ath5k_global_debugfs);
}
void
ath5k_debug_finish_device(struct ath5k_softc *sc)
{
debugfs_remove(sc->debug.debugfs_debug);
debugfs_remove(sc->debug.debugfs_registers);
debugfs_remove(sc->debug.debugfs_beacon);
debugfs_remove(sc->debug.debugfs_reset);
debugfs_remove(sc->debug.debugfs_phydir);
}
/* functions used in other places */
void
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
ath5k_debug_dump_bands(struct ath5k_softc *sc)
{
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
unsigned int b, i;
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
if (likely(!(sc->debug.level & ATH5K_DEBUG_DUMPBANDS)))
return;
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
BUG_ON(!sc->sbands);
for (b = 0; b < IEEE80211_NUM_BANDS; b++) {
struct ieee80211_supported_band *band = &sc->sbands[b];
char bname[6];
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
switch (band->band) {
case IEEE80211_BAND_2GHZ:
strcpy(bname, "2 GHz");
break;
case IEEE80211_BAND_5GHZ:
strcpy(bname, "5 GHz");
break;
default:
printk(KERN_DEBUG "Band not supported: %d\n",
band->band);
return;
}
printk(KERN_DEBUG "Band %s: channels %d, rates %d\n", bname,
band->n_channels, band->n_bitrates);
printk(KERN_DEBUG " channels:\n");
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
for (i = 0; i < band->n_channels; i++)
printk(KERN_DEBUG " %3d %d %.4x %.4x\n",
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
ieee80211_frequency_to_channel(
band->channels[i].center_freq),
band->channels[i].center_freq,
band->channels[i].hw_value,
band->channels[i].flags);
printk(KERN_DEBUG " rates:\n");
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
for (i = 0; i < band->n_bitrates; i++)
printk(KERN_DEBUG " %4d %.4x %.4x %.4x\n",
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
band->bitrates[i].bitrate,
band->bitrates[i].hw_value,
band->bitrates[i].flags,
band->bitrates[i].hw_value_short);
}
}
static inline void
ath5k_debug_printrxbuf(struct ath5k_buf *bf, int done,
struct ath5k_rx_status *rs)
{
struct ath5k_desc *ds = bf->desc;
struct ath5k_hw_all_rx_desc *rd = &ds->ud.ds_rx;
printk(KERN_DEBUG "R (%p %llx) %08x %08x %08x %08x %08x %08x %c\n",
ds, (unsigned long long)bf->daddr,
ds->ds_link, ds->ds_data,
rd->rx_ctl.rx_control_0, rd->rx_ctl.rx_control_1,
rd->u.rx_stat.rx_status_0, rd->u.rx_stat.rx_status_0,
!done ? ' ' : (rs->rs_status == 0) ? '*' : '!');
}
void
ath5k_debug_printrxbuffs(struct ath5k_softc *sc, struct ath5k_hw *ah)
{
struct ath5k_desc *ds;
struct ath5k_buf *bf;
struct ath5k_rx_status rs = {};
int status;
if (likely(!(sc->debug.level & ATH5K_DEBUG_RESET)))
return;
printk(KERN_DEBUG "rx queue %x, link %p\n",
ath5k_hw_get_rxdp(ah), sc->rxlink);
spin_lock_bh(&sc->rxbuflock);
list_for_each_entry(bf, &sc->rxbuf, list) {
ds = bf->desc;
status = ah->ah_proc_rx_desc(ah, ds, &rs);
if (!status)
ath5k_debug_printrxbuf(bf, status == 0, &rs);
}
spin_unlock_bh(&sc->rxbuflock);
}
void
ath5k_debug_dump_skb(struct ath5k_softc *sc,
struct sk_buff *skb, const char *prefix, int tx)
{
char buf[16];
if (likely(!((tx && (sc->debug.level & ATH5K_DEBUG_DUMP_TX)) ||
(!tx && (sc->debug.level & ATH5K_DEBUG_DUMP_RX)))))
return;
snprintf(buf, sizeof(buf), "%s %s", wiphy_name(sc->hw->wiphy), prefix);
print_hex_dump_bytes(buf, DUMP_PREFIX_NONE, skb->data,
min(200U, skb->len));
printk(KERN_DEBUG "\n");
}
void
ath5k_debug_printtxbuf(struct ath5k_softc *sc, struct ath5k_buf *bf)
{
struct ath5k_desc *ds = bf->desc;
struct ath5k_hw_5212_tx_desc *td = &ds->ud.ds_tx5212;
struct ath5k_tx_status ts = {};
int done;
if (likely(!(sc->debug.level & ATH5K_DEBUG_RESET)))
return;
done = sc->ah->ah_proc_tx_desc(sc->ah, bf->desc, &ts);
printk(KERN_DEBUG "T (%p %llx) %08x %08x %08x %08x %08x %08x %08x "
"%08x %c\n", ds, (unsigned long long)bf->daddr, ds->ds_link,
ds->ds_data, td->tx_ctl.tx_control_0, td->tx_ctl.tx_control_1,
td->tx_ctl.tx_control_2, td->tx_ctl.tx_control_3,
td->tx_stat.tx_status_0, td->tx_stat.tx_status_1,
done ? ' ' : (ts.ts_status == 0) ? '*' : '!');
}
ath5k: Port debug.c over to the new band API and enable as build option This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-04 23:03:54 +08:00
#endif /* ifdef CONFIG_ATH5K_DEBUG */