OpenCloudOS-Kernel/arch/x86/pci/vmd.c

757 lines
20 KiB
C
Raw Normal View History

x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
/*
* Volume Management Device driver
* Copyright (c) 2015, Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*/
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/msi.h>
#include <linux/pci.h>
#include <linux/rculist.h>
#include <linux/rcupdate.h>
#include <asm/irqdomain.h>
#include <asm/device.h>
#include <asm/msi.h>
#include <asm/msidef.h>
#define VMD_CFGBAR 0
#define VMD_MEMBAR1 2
#define VMD_MEMBAR2 4
/*
* Lock for manipulating VMD IRQ lists.
*/
static DEFINE_RAW_SPINLOCK(list_lock);
/**
* struct vmd_irq - private data to map driver IRQ to the VMD shared vector
* @node: list item for parent traversal.
* @rcu: RCU callback item for freeing.
* @irq: back pointer to parent.
* @virq: the virtual IRQ value provided to the requesting driver.
*
* Every MSI/MSI-X IRQ requested for a device in a VMD domain will be mapped to
* a VMD IRQ using this structure.
*/
struct vmd_irq {
struct list_head node;
struct rcu_head rcu;
struct vmd_irq_list *irq;
unsigned int virq;
};
/**
* struct vmd_irq_list - list of driver requested IRQs mapping to a VMD vector
* @irq_list: the list of irq's the VMD one demuxes to.
* @vmd_vector: the h/w IRQ assigned to the VMD.
* @index: index into the VMD MSI-X table; used for message routing.
* @count: number of child IRQs assigned to this vector; used to track
* sharing.
*/
struct vmd_irq_list {
struct list_head irq_list;
struct vmd_dev *vmd;
unsigned int vmd_vector;
unsigned int index;
unsigned int count;
};
struct vmd_dev {
struct pci_dev *dev;
spinlock_t cfg_lock;
char __iomem *cfgbar;
int msix_count;
struct msix_entry *msix_entries;
struct vmd_irq_list *irqs;
struct pci_sysdata sysdata;
struct resource resources[3];
struct irq_domain *irq_domain;
struct pci_bus *bus;
#ifdef CONFIG_X86_DEV_DMA_OPS
struct dma_map_ops dma_ops;
struct dma_domain dma_domain;
#endif
};
static inline struct vmd_dev *vmd_from_bus(struct pci_bus *bus)
{
return container_of(bus->sysdata, struct vmd_dev, sysdata);
}
/*
* Drivers managing a device in a VMD domain allocate their own IRQs as before,
* but the MSI entry for the hardware it's driving will be programmed with a
* destination ID for the VMD MSI-X table. The VMD muxes interrupts in its
* domain into one of its own, and the VMD driver de-muxes these for the
* handlers sharing that VMD IRQ. The vmd irq_domain provides the operations
* and irq_chip to set this up.
*/
static void vmd_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
{
struct vmd_irq *vmdirq = data->chip_data;
struct vmd_irq_list *irq = vmdirq->irq;
msg->address_hi = MSI_ADDR_BASE_HI;
msg->address_lo = MSI_ADDR_BASE_LO | MSI_ADDR_DEST_ID(irq->index);
msg->data = 0;
}
/*
* We rely on MSI_FLAG_USE_DEF_CHIP_OPS to set the IRQ mask/unmask ops.
*/
static void vmd_irq_enable(struct irq_data *data)
{
struct vmd_irq *vmdirq = data->chip_data;
raw_spin_lock(&list_lock);
list_add_tail_rcu(&vmdirq->node, &vmdirq->irq->irq_list);
raw_spin_unlock(&list_lock);
data->chip->irq_unmask(data);
}
static void vmd_irq_disable(struct irq_data *data)
{
struct vmd_irq *vmdirq = data->chip_data;
data->chip->irq_mask(data);
raw_spin_lock(&list_lock);
list_del_rcu(&vmdirq->node);
raw_spin_unlock(&list_lock);
}
/*
* XXX: Stubbed until we develop acceptable way to not create conflicts with
* other devices sharing the same vector.
*/
static int vmd_irq_set_affinity(struct irq_data *data,
const struct cpumask *dest, bool force)
{
return -EINVAL;
}
static struct irq_chip vmd_msi_controller = {
.name = "VMD-MSI",
.irq_enable = vmd_irq_enable,
.irq_disable = vmd_irq_disable,
.irq_compose_msi_msg = vmd_compose_msi_msg,
.irq_set_affinity = vmd_irq_set_affinity,
};
static irq_hw_number_t vmd_get_hwirq(struct msi_domain_info *info,
msi_alloc_info_t *arg)
{
return 0;
}
/*
* XXX: We can be even smarter selecting the best IRQ once we solve the
* affinity problem.
*/
static struct vmd_irq_list *vmd_next_irq(struct vmd_dev *vmd)
{
int i, best = 0;
raw_spin_lock(&list_lock);
for (i = 1; i < vmd->msix_count; i++)
if (vmd->irqs[i].count < vmd->irqs[best].count)
best = i;
vmd->irqs[best].count++;
raw_spin_unlock(&list_lock);
return &vmd->irqs[best];
}
static int vmd_msi_init(struct irq_domain *domain, struct msi_domain_info *info,
unsigned int virq, irq_hw_number_t hwirq,
msi_alloc_info_t *arg)
{
struct vmd_dev *vmd = vmd_from_bus(msi_desc_to_pci_dev(arg->desc)->bus);
struct vmd_irq *vmdirq = kzalloc(sizeof(*vmdirq), GFP_KERNEL);
if (!vmdirq)
return -ENOMEM;
INIT_LIST_HEAD(&vmdirq->node);
vmdirq->irq = vmd_next_irq(vmd);
vmdirq->virq = virq;
irq_domain_set_info(domain, virq, vmdirq->irq->vmd_vector, info->chip,
vmdirq, handle_simple_irq, vmd, NULL);
return 0;
}
static void vmd_msi_free(struct irq_domain *domain,
struct msi_domain_info *info, unsigned int virq)
{
struct vmd_irq *vmdirq = irq_get_chip_data(virq);
/* XXX: Potential optimization to rebalance */
raw_spin_lock(&list_lock);
vmdirq->irq->count--;
raw_spin_unlock(&list_lock);
kfree_rcu(vmdirq, rcu);
}
static int vmd_msi_prepare(struct irq_domain *domain, struct device *dev,
int nvec, msi_alloc_info_t *arg)
{
struct pci_dev *pdev = to_pci_dev(dev);
struct vmd_dev *vmd = vmd_from_bus(pdev->bus);
if (nvec > vmd->msix_count)
return vmd->msix_count;
memset(arg, 0, sizeof(*arg));
return 0;
}
static void vmd_set_desc(msi_alloc_info_t *arg, struct msi_desc *desc)
{
arg->desc = desc;
}
static struct msi_domain_ops vmd_msi_domain_ops = {
.get_hwirq = vmd_get_hwirq,
.msi_init = vmd_msi_init,
.msi_free = vmd_msi_free,
.msi_prepare = vmd_msi_prepare,
.set_desc = vmd_set_desc,
};
static struct msi_domain_info vmd_msi_domain_info = {
.flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
MSI_FLAG_PCI_MSIX,
.ops = &vmd_msi_domain_ops,
.chip = &vmd_msi_controller,
};
#ifdef CONFIG_X86_DEV_DMA_OPS
/*
* VMD replaces the requester ID with its own. DMA mappings for devices in a
* VMD domain need to be mapped for the VMD, not the device requiring
* the mapping.
*/
static struct device *to_vmd_dev(struct device *dev)
{
struct pci_dev *pdev = to_pci_dev(dev);
struct vmd_dev *vmd = vmd_from_bus(pdev->bus);
return &vmd->dev->dev;
}
static struct dma_map_ops *vmd_dma_ops(struct device *dev)
{
return to_vmd_dev(dev)->archdata.dma_ops;
}
static void *vmd_alloc(struct device *dev, size_t size, dma_addr_t *addr,
gfp_t flag, struct dma_attrs *attrs)
{
return vmd_dma_ops(dev)->alloc(to_vmd_dev(dev), size, addr, flag,
attrs);
}
static void vmd_free(struct device *dev, size_t size, void *vaddr,
dma_addr_t addr, struct dma_attrs *attrs)
{
return vmd_dma_ops(dev)->free(to_vmd_dev(dev), size, vaddr, addr,
attrs);
}
static int vmd_mmap(struct device *dev, struct vm_area_struct *vma,
void *cpu_addr, dma_addr_t addr, size_t size,
struct dma_attrs *attrs)
{
return vmd_dma_ops(dev)->mmap(to_vmd_dev(dev), vma, cpu_addr, addr,
size, attrs);
}
static int vmd_get_sgtable(struct device *dev, struct sg_table *sgt,
void *cpu_addr, dma_addr_t addr, size_t size,
struct dma_attrs *attrs)
{
return vmd_dma_ops(dev)->get_sgtable(to_vmd_dev(dev), sgt, cpu_addr,
addr, size, attrs);
}
static dma_addr_t vmd_map_page(struct device *dev, struct page *page,
unsigned long offset, size_t size,
enum dma_data_direction dir,
struct dma_attrs *attrs)
{
return vmd_dma_ops(dev)->map_page(to_vmd_dev(dev), page, offset, size,
dir, attrs);
}
static void vmd_unmap_page(struct device *dev, dma_addr_t addr, size_t size,
enum dma_data_direction dir, struct dma_attrs *attrs)
{
vmd_dma_ops(dev)->unmap_page(to_vmd_dev(dev), addr, size, dir, attrs);
}
static int vmd_map_sg(struct device *dev, struct scatterlist *sg, int nents,
enum dma_data_direction dir, struct dma_attrs *attrs)
{
return vmd_dma_ops(dev)->map_sg(to_vmd_dev(dev), sg, nents, dir, attrs);
}
static void vmd_unmap_sg(struct device *dev, struct scatterlist *sg, int nents,
enum dma_data_direction dir, struct dma_attrs *attrs)
{
vmd_dma_ops(dev)->unmap_sg(to_vmd_dev(dev), sg, nents, dir, attrs);
}
static void vmd_sync_single_for_cpu(struct device *dev, dma_addr_t addr,
size_t size, enum dma_data_direction dir)
{
vmd_dma_ops(dev)->sync_single_for_cpu(to_vmd_dev(dev), addr, size, dir);
}
static void vmd_sync_single_for_device(struct device *dev, dma_addr_t addr,
size_t size, enum dma_data_direction dir)
{
vmd_dma_ops(dev)->sync_single_for_device(to_vmd_dev(dev), addr, size,
dir);
}
static void vmd_sync_sg_for_cpu(struct device *dev, struct scatterlist *sg,
int nents, enum dma_data_direction dir)
{
vmd_dma_ops(dev)->sync_sg_for_cpu(to_vmd_dev(dev), sg, nents, dir);
}
static void vmd_sync_sg_for_device(struct device *dev, struct scatterlist *sg,
int nents, enum dma_data_direction dir)
{
vmd_dma_ops(dev)->sync_sg_for_device(to_vmd_dev(dev), sg, nents, dir);
}
static int vmd_mapping_error(struct device *dev, dma_addr_t addr)
{
return vmd_dma_ops(dev)->mapping_error(to_vmd_dev(dev), addr);
}
static int vmd_dma_supported(struct device *dev, u64 mask)
{
return vmd_dma_ops(dev)->dma_supported(to_vmd_dev(dev), mask);
}
#ifdef ARCH_HAS_DMA_GET_REQUIRED_MASK
static u64 vmd_get_required_mask(struct device *dev)
{
return vmd_dma_ops(dev)->get_required_mask(to_vmd_dev(dev));
}
#endif
static void vmd_teardown_dma_ops(struct vmd_dev *vmd)
{
struct dma_domain *domain = &vmd->dma_domain;
if (vmd->dev->dev.archdata.dma_ops)
del_dma_domain(domain);
}
#define ASSIGN_VMD_DMA_OPS(source, dest, fn) \
do { \
if (source->fn) \
dest->fn = vmd_##fn; \
} while (0)
static void vmd_setup_dma_ops(struct vmd_dev *vmd)
{
const struct dma_map_ops *source = vmd->dev->dev.archdata.dma_ops;
struct dma_map_ops *dest = &vmd->dma_ops;
struct dma_domain *domain = &vmd->dma_domain;
domain->domain_nr = vmd->sysdata.domain;
domain->dma_ops = dest;
if (!source)
return;
ASSIGN_VMD_DMA_OPS(source, dest, alloc);
ASSIGN_VMD_DMA_OPS(source, dest, free);
ASSIGN_VMD_DMA_OPS(source, dest, mmap);
ASSIGN_VMD_DMA_OPS(source, dest, get_sgtable);
ASSIGN_VMD_DMA_OPS(source, dest, map_page);
ASSIGN_VMD_DMA_OPS(source, dest, unmap_page);
ASSIGN_VMD_DMA_OPS(source, dest, map_sg);
ASSIGN_VMD_DMA_OPS(source, dest, unmap_sg);
ASSIGN_VMD_DMA_OPS(source, dest, sync_single_for_cpu);
ASSIGN_VMD_DMA_OPS(source, dest, sync_single_for_device);
ASSIGN_VMD_DMA_OPS(source, dest, sync_sg_for_cpu);
ASSIGN_VMD_DMA_OPS(source, dest, sync_sg_for_device);
ASSIGN_VMD_DMA_OPS(source, dest, mapping_error);
ASSIGN_VMD_DMA_OPS(source, dest, dma_supported);
#ifdef ARCH_HAS_DMA_GET_REQUIRED_MASK
ASSIGN_VMD_DMA_OPS(source, dest, get_required_mask);
#endif
add_dma_domain(domain);
}
#undef ASSIGN_VMD_DMA_OPS
#else
static void vmd_teardown_dma_ops(struct vmd_dev *vmd) {}
static void vmd_setup_dma_ops(struct vmd_dev *vmd) {}
#endif
static char __iomem *vmd_cfg_addr(struct vmd_dev *vmd, struct pci_bus *bus,
unsigned int devfn, int reg, int len)
{
char __iomem *addr = vmd->cfgbar +
(bus->number << 20) + (devfn << 12) + reg;
if ((addr - vmd->cfgbar) + len >=
resource_size(&vmd->dev->resource[VMD_CFGBAR]))
return NULL;
return addr;
}
/*
* CPU may deadlock if config space is not serialized on some versions of this
* hardware, so all config space access is done under a spinlock.
*/
static int vmd_pci_read(struct pci_bus *bus, unsigned int devfn, int reg,
int len, u32 *value)
{
struct vmd_dev *vmd = vmd_from_bus(bus);
char __iomem *addr = vmd_cfg_addr(vmd, bus, devfn, reg, len);
unsigned long flags;
int ret = 0;
if (!addr)
return -EFAULT;
spin_lock_irqsave(&vmd->cfg_lock, flags);
switch (len) {
case 1:
*value = readb(addr);
break;
case 2:
*value = readw(addr);
break;
case 4:
*value = readl(addr);
break;
default:
ret = -EINVAL;
break;
}
spin_unlock_irqrestore(&vmd->cfg_lock, flags);
return ret;
}
/*
* VMD h/w converts non-posted config writes to posted memory writes. The
* read-back in this function forces the completion so it returns only after
* the config space was written, as expected.
*/
static int vmd_pci_write(struct pci_bus *bus, unsigned int devfn, int reg,
int len, u32 value)
{
struct vmd_dev *vmd = vmd_from_bus(bus);
char __iomem *addr = vmd_cfg_addr(vmd, bus, devfn, reg, len);
unsigned long flags;
int ret = 0;
if (!addr)
return -EFAULT;
spin_lock_irqsave(&vmd->cfg_lock, flags);
switch (len) {
case 1:
writeb(value, addr);
readb(addr);
break;
case 2:
writew(value, addr);
readw(addr);
break;
case 4:
writel(value, addr);
readl(addr);
break;
default:
ret = -EINVAL;
break;
}
spin_unlock_irqrestore(&vmd->cfg_lock, flags);
return ret;
}
static struct pci_ops vmd_ops = {
.read = vmd_pci_read,
.write = vmd_pci_write,
};
static void vmd_attach_resources(struct vmd_dev *vmd)
{
vmd->dev->resource[VMD_MEMBAR1].child = &vmd->resources[1];
vmd->dev->resource[VMD_MEMBAR2].child = &vmd->resources[2];
}
static void vmd_detach_resources(struct vmd_dev *vmd)
{
vmd->dev->resource[VMD_MEMBAR1].child = NULL;
vmd->dev->resource[VMD_MEMBAR2].child = NULL;
}
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
/*
* VMD domains start at 0x1000 to not clash with ACPI _SEG domains.
*/
static int vmd_find_free_domain(void)
{
int domain = 0xffff;
struct pci_bus *bus = NULL;
while ((bus = pci_find_next_bus(bus)) != NULL)
domain = max_t(int, domain, pci_domain_nr(bus));
return domain + 1;
}
static int vmd_enable_domain(struct vmd_dev *vmd)
{
struct pci_sysdata *sd = &vmd->sysdata;
struct resource *res;
u32 upper_bits;
unsigned long flags;
LIST_HEAD(resources);
res = &vmd->dev->resource[VMD_CFGBAR];
vmd->resources[0] = (struct resource) {
.name = "VMD CFGBAR",
.start = 0,
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
.end = (resource_size(res) >> 20) - 1,
.flags = IORESOURCE_BUS | IORESOURCE_PCI_FIXED,
};
/*
* If the window is below 4GB, clear IORESOURCE_MEM_64 so we can
* put 32-bit resources in the window.
*
* There's no hardware reason why a 64-bit window *couldn't*
* contain a 32-bit resource, but pbus_size_mem() computes the
* bridge window size assuming a 64-bit window will contain no
* 32-bit resources. __pci_assign_resource() enforces that
* artificial restriction to make sure everything will fit.
*
* The only way we could use a 64-bit non-prefechable MEMBAR is
* if its address is <4GB so that we can convert it to a 32-bit
* resource. To be visible to the host OS, all VMD endpoints must
* be initially configured by platform BIOS, which includes setting
* up these resources. We can assume the device is configured
* according to the platform needs.
*/
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
res = &vmd->dev->resource[VMD_MEMBAR1];
upper_bits = upper_32_bits(res->end);
flags = res->flags & ~IORESOURCE_SIZEALIGN;
if (!upper_bits)
flags &= ~IORESOURCE_MEM_64;
vmd->resources[1] = (struct resource) {
.name = "VMD MEMBAR1",
.start = res->start,
.end = res->end,
.flags = flags,
.parent = res,
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
};
res = &vmd->dev->resource[VMD_MEMBAR2];
upper_bits = upper_32_bits(res->end);
flags = res->flags & ~IORESOURCE_SIZEALIGN;
if (!upper_bits)
flags &= ~IORESOURCE_MEM_64;
vmd->resources[2] = (struct resource) {
.name = "VMD MEMBAR2",
.start = res->start + 0x2000,
.end = res->end,
.flags = flags,
.parent = res,
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
};
sd->domain = vmd_find_free_domain();
if (sd->domain < 0)
return sd->domain;
sd->node = pcibus_to_node(vmd->dev->bus);
vmd->irq_domain = pci_msi_create_irq_domain(NULL, &vmd_msi_domain_info,
NULL);
if (!vmd->irq_domain)
return -ENODEV;
pci_add_resource(&resources, &vmd->resources[0]);
pci_add_resource(&resources, &vmd->resources[1]);
pci_add_resource(&resources, &vmd->resources[2]);
vmd->bus = pci_create_root_bus(&vmd->dev->dev, 0, &vmd_ops, sd,
&resources);
if (!vmd->bus) {
pci_free_resource_list(&resources);
irq_domain_remove(vmd->irq_domain);
return -ENODEV;
}
vmd_attach_resources(vmd);
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
vmd_setup_dma_ops(vmd);
dev_set_msi_domain(&vmd->bus->dev, vmd->irq_domain);
pci_rescan_bus(vmd->bus);
WARN(sysfs_create_link(&vmd->dev->dev.kobj, &vmd->bus->dev.kobj,
"domain"), "Can't create symlink to domain\n");
return 0;
}
static irqreturn_t vmd_irq(int irq, void *data)
{
struct vmd_irq_list *irqs = data;
struct vmd_irq *vmdirq;
rcu_read_lock();
list_for_each_entry_rcu(vmdirq, &irqs->irq_list, node)
generic_handle_irq(vmdirq->virq);
rcu_read_unlock();
return IRQ_HANDLED;
}
static int vmd_probe(struct pci_dev *dev, const struct pci_device_id *id)
{
struct vmd_dev *vmd;
int i, err;
if (resource_size(&dev->resource[VMD_CFGBAR]) < (1 << 20))
return -ENOMEM;
vmd = devm_kzalloc(&dev->dev, sizeof(*vmd), GFP_KERNEL);
if (!vmd)
return -ENOMEM;
vmd->dev = dev;
err = pcim_enable_device(dev);
if (err < 0)
return err;
vmd->cfgbar = pcim_iomap(dev, VMD_CFGBAR, 0);
if (!vmd->cfgbar)
return -ENOMEM;
pci_set_master(dev);
if (dma_set_mask_and_coherent(&dev->dev, DMA_BIT_MASK(64)) &&
dma_set_mask_and_coherent(&dev->dev, DMA_BIT_MASK(32)))
return -ENODEV;
vmd->msix_count = pci_msix_vec_count(dev);
if (vmd->msix_count < 0)
return -ENODEV;
vmd->irqs = devm_kcalloc(&dev->dev, vmd->msix_count, sizeof(*vmd->irqs),
GFP_KERNEL);
if (!vmd->irqs)
return -ENOMEM;
vmd->msix_entries = devm_kcalloc(&dev->dev, vmd->msix_count,
sizeof(*vmd->msix_entries),
GFP_KERNEL);
if (!vmd->msix_entries)
return -ENOMEM;
for (i = 0; i < vmd->msix_count; i++)
vmd->msix_entries[i].entry = i;
vmd->msix_count = pci_enable_msix_range(vmd->dev, vmd->msix_entries, 1,
vmd->msix_count);
if (vmd->msix_count < 0)
return vmd->msix_count;
for (i = 0; i < vmd->msix_count; i++) {
INIT_LIST_HEAD(&vmd->irqs[i].irq_list);
vmd->irqs[i].vmd_vector = vmd->msix_entries[i].vector;
vmd->irqs[i].index = i;
err = devm_request_irq(&dev->dev, vmd->irqs[i].vmd_vector,
vmd_irq, 0, "vmd", &vmd->irqs[i]);
if (err)
return err;
}
spin_lock_init(&vmd->cfg_lock);
pci_set_drvdata(dev, vmd);
err = vmd_enable_domain(vmd);
if (err)
return err;
dev_info(&vmd->dev->dev, "Bound to PCI domain %04x\n",
vmd->sysdata.domain);
return 0;
}
static void vmd_remove(struct pci_dev *dev)
{
struct vmd_dev *vmd = pci_get_drvdata(dev);
vmd_detach_resources(vmd);
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-13 04:18:10 +08:00
pci_set_drvdata(dev, NULL);
sysfs_remove_link(&vmd->dev->dev.kobj, "domain");
pci_stop_root_bus(vmd->bus);
pci_remove_root_bus(vmd->bus);
vmd_teardown_dma_ops(vmd);
irq_domain_remove(vmd->irq_domain);
}
#ifdef CONFIG_PM
static int vmd_suspend(struct device *dev)
{
struct pci_dev *pdev = to_pci_dev(dev);
pci_save_state(pdev);
return 0;
}
static int vmd_resume(struct device *dev)
{
struct pci_dev *pdev = to_pci_dev(dev);
pci_restore_state(pdev);
return 0;
}
#endif
static SIMPLE_DEV_PM_OPS(vmd_dev_pm_ops, vmd_suspend, vmd_resume);
static const struct pci_device_id vmd_ids[] = {
{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x201d),},
{0,}
};
MODULE_DEVICE_TABLE(pci, vmd_ids);
static struct pci_driver vmd_drv = {
.name = "vmd",
.id_table = vmd_ids,
.probe = vmd_probe,
.remove = vmd_remove,
.driver = {
.pm = &vmd_dev_pm_ops,
},
};
module_pci_driver(vmd_drv);
MODULE_AUTHOR("Intel Corporation");
MODULE_LICENSE("GPL v2");
MODULE_VERSION("0.6");