License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
|
|
|
# SPDX-License-Identifier: GPL-2.0
|
2011-10-20 22:52:46 +08:00
|
|
|
#
|
|
|
|
|
# Generic framework for controlling remote processors
|
|
|
|
|
#
|
|
|
|
|
|
|
|
|
|
obj-$(CONFIG_REMOTEPROC) += remoteproc.o
|
|
|
|
|
remoteproc-y := remoteproc_core.o
|
2020-07-17 06:20:31 +08:00
|
|
|
remoteproc-y += remoteproc_coredump.o
|
2011-10-20 23:24:15 +08:00
|
|
|
remoteproc-y += remoteproc_debugfs.o
|
2016-10-19 20:05:47 +08:00
|
|
|
remoteproc-y += remoteproc_sysfs.o
|
2012-02-13 10:03:31 +08:00
|
|
|
remoteproc-y += remoteproc_virtio.o
|
2012-07-15 16:25:27 +08:00
|
|
|
remoteproc-y += remoteproc_elf_loader.o
|
2020-07-30 01:40:00 +08:00
|
|
|
obj-$(CONFIG_REMOTEPROC_CDEV) += remoteproc_cdev.o
|
2017-08-17 15:15:26 +08:00
|
|
|
obj-$(CONFIG_IMX_REMOTEPROC) += imx_rproc.o
|
2020-05-15 18:43:39 +08:00
|
|
|
obj-$(CONFIG_INGENIC_VPU_RPROC) += ingenic_rproc.o
|
2019-11-12 19:03:25 +08:00
|
|
|
obj-$(CONFIG_MTK_SCP) += mtk_scp.o mtk_scp_ipi.o
|
2011-10-21 00:53:35 +08:00
|
|
|
obj-$(CONFIG_OMAP_REMOTEPROC) += omap_remoteproc.o
|
2015-05-23 04:45:30 +08:00
|
|
|
obj-$(CONFIG_WKUP_M3_RPROC) += wkup_m3_rproc.o
|
2013-04-10 05:20:21 +08:00
|
|
|
obj-$(CONFIG_DA8XX_REMOTEPROC) += da8xx_remoteproc.o
|
remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs
The Texas Instrument's Keystone 2 family of SoCs has 1 or more
TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
that can be configured and partitioned as either RAM and/or Cache,
and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC)
with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).
A new remoteproc module is added to perform the device management of
these DSP devices. The driver expects the firmware names to be of the
form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
uses the standard remoteproc core ELF loader. The support is limited
to images only using the DSP internal memories at the moment. This
remoteproc driver is also designed to work with virtio, and uses the
IPC Generation registers for performing the virtio signalling and
getting notified of exceptions.
The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2017-06-14 07:45:12 +08:00
|
|
|
obj-$(CONFIG_KEYSTONE_REMOTEPROC) += keystone_remoteproc.o
|
2020-12-08 22:09:58 +08:00
|
|
|
obj-$(CONFIG_PRU_REMOTEPROC) += pru_rproc.o
|
2020-06-23 03:19:39 +08:00
|
|
|
obj-$(CONFIG_QCOM_PIL_INFO) += qcom_pil_info.o
|
2017-01-27 18:28:32 +08:00
|
|
|
obj-$(CONFIG_QCOM_RPROC_COMMON) += qcom_common.o
|
2018-06-05 04:30:36 +08:00
|
|
|
obj-$(CONFIG_QCOM_Q6V5_COMMON) += qcom_q6v5.o
|
2018-09-24 19:07:50 +08:00
|
|
|
obj-$(CONFIG_QCOM_Q6V5_ADSP) += qcom_q6v5_adsp.o
|
2018-09-25 07:45:26 +08:00
|
|
|
obj-$(CONFIG_QCOM_Q6V5_MSS) += qcom_q6v5_mss.o
|
2018-09-25 07:45:25 +08:00
|
|
|
obj-$(CONFIG_QCOM_Q6V5_PAS) += qcom_q6v5_pas.o
|
2018-06-08 01:27:11 +08:00
|
|
|
obj-$(CONFIG_QCOM_Q6V5_WCSS) += qcom_q6v5_wcss.o
|
2017-08-28 12:51:38 +08:00
|
|
|
obj-$(CONFIG_QCOM_SYSMON) += qcom_sysmon.o
|
2016-11-04 10:37:25 +08:00
|
|
|
obj-$(CONFIG_QCOM_WCNSS_PIL) += qcom_wcnss_pil.o
|
|
|
|
|
qcom_wcnss_pil-y += qcom_wcnss.o
|
|
|
|
|
qcom_wcnss_pil-y += qcom_wcnss_iris.o
|
2016-01-12 20:46:18 +08:00
|
|
|
obj-$(CONFIG_ST_REMOTEPROC) += st_remoteproc.o
|
2016-10-18 17:39:06 +08:00
|
|
|
obj-$(CONFIG_ST_SLIM_REMOTEPROC) += st_slim_rproc.o
|
2019-05-14 16:26:58 +08:00
|
|
|
obj-$(CONFIG_STM32_RPROC) += stm32_rproc.o
|
remoteproc: k3-dsp: Add a remoteproc driver of K3 C66x DSPs
The Texas Instrument's K3 J721E SoCs have two C66x DSP Subsystems in MAIN
voltage domain that are based on the TI's standard TMS320C66x DSP CorePac
module. Each subsystem has a Fixed/Floating-Point DSP CPU, with 32 KB each
of L1P & L1D SRAMs that can be configured and partitioned as either RAM
and/or Cache, and 288 KB of L2 SRAM with 256 KB of memory configurable as
either RAM and/or Cache. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC) with a
Region Address Translator (RAT) unit for 32-bit to 48-bit address
extension/translations, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).
A new remoteproc module is added to perform the device management of
these DSP devices. The support is limited to images using only external
DDR memory at the moment, the loading support to internal memories and
any on-chip RAM memories will be added in a subsequent patch. RAT support
is also left for a future patch, and as such the reserved memory carveout
regions are all expected to be using memory regions within the first 2 GB.
Error Recovery and Power Management features are not currently supported.
The C66x remote processors do not have an MMU, and so require fixed memory
carveout regions matching the firmware image addresses. Support for this
is provided by mandating multiple memory regions to be attached to the
remoteproc device. The first memory region will be used to serve as the
DMA pool for all dynamic allocations like the vrings and vring buffers.
The remaining memory regions are mapped into the kernel at device probe
time, and are used to provide address translations for firmware image
segments without the need for any RSC_CARVEOUT entries. Any firmware
image using memory outside of the supplied reserved memory carveout
regions will be errored out.
The driver uses various TI-SCI interfaces to talk to the System Controller
(DMSC) for managing configuration, power and reset management of these
cores. IPC between the A72 cores and the DSP cores is supported through
the virtio rpmsg stack using shared memory and OMAP Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-6-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-07-22 06:36:16 +08:00
|
|
|
obj-$(CONFIG_TI_K3_DSP_REMOTEPROC) += ti_k3_dsp_remoteproc.o
|
remoteproc: k3-r5: Add a remoteproc driver for R5F subsystem
The TI K3 family of SoCs typically have one or more dual-core Arm Cortex
R5F processor clusters/subsystems (R5FSS). This R5F subsystem/cluster
can be configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. This subsystem
has 64 KB each Tightly-Coupled Memory (TCM) internal memories for each
core split between two banks - TCMA and TCMB (further interleaved into
two banks). The subsystem does not have an MMU, but has a Region Address
Translater (RAT) module that is accessible only from the R5Fs for providing
translations between 32-bit CPU addresses into larger system bus addresses.
Add a remoteproc driver to support this subsystem to be able to load and
boot the R5F cores primarily in LockStep mode. The code also includes the
base support for Split mode. Error Recovery and Power Management features
are not currently supported. Loading support includes the internal TCMs
and DDR. RAT support is left for a future patch, and as such the reserved
memory carveout regions are all expected to be using memory regions within
the first 2 GB.
The R5F remote processors do not have an MMU, and so require fixed memory
carveout regions matching the firmware image addresses. Support for this
is provided by mandating multiple memory regions to be attached to the
remoteproc device. The first memory region will be used to serve as the
DMA pool for all dynamic allocations like the vrings and vring buffers.
The remaining memory regions are mapped into the kernel at device probe
time, and are used to provide address translations for firmware image
segments without the need for any RSC_CARVEOUT entries. Any firmware
image using memory outside of the supplied reserved memory carveout
regions will be errored out.
The R5F processors on TI K3 SoCs require a specific sequence for booting
and shutting down the processors. This sequence is also dependent on the
mode (LockStep or Split) the R5F cluster is configured for. The R5F cores
have a Memory Protection Unit (MPU) that has a default configuration that
does not allow the cores to run out of DDR out of reset. This is resolved
by using the TCMs for boot-strapping code that applies the appropriate
executable permissions on desired DDR memory. The loading into the TCMs
requires that the resets be released first with the cores in halted state.
The Power Sleep Controller (PSC) module on K3 SoCs requires that the cores
be in WFI/WFE states with no active bus transactions before the cores can
be put back into reset. Support for this is provided by using the newly
introduced .prepare() and .unprepare() ops in the remoteproc core. The
.prepare() ops is invoked before any loading, and the .unprepare() ops
is invoked after the remoteproc resource cleanup. The R5F core resets
are deasserted in .prepare() and asserted in .unprepare(), and the cores
themselves are started and halted in .start() and .stop() ops. This
ensures symmetric usage and allows the R5F cores state machine to be
maintained properly between using the sysfs 'state' variable, bind/unbind
and regular module load/unload flows.
The subsystem is represented as a single remoteproc in LockStep mode, and
as two remoteprocs in Split mode. The driver uses various TI-SCI interfaces
to talk to the System Controller (DMSC) for managing configuration, power
and reset management of these cores. IPC between the A53 cores and the R5
cores is supported through the virtio rpmsg stack using shared memory and
OMAP Mailboxes.
The AM65x SoCs typically have a single R5FSS in the MCU voltage domain. The
J721E SoCs uses a slightly revised IP and typically have three R5FSSs, with
one cluster present within the MCU voltage domain (MCU_R5FSS0), and the
remaining two clusters present in the MAIN voltage domain (MAIN_R5FSS0 and
MAIN_R5FSS1). The integration of these clusters on J721E SoC is also
slightly different in that these IPs do support an actual local reset line,
while they are a no-op on AM65x SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-10-03 07:42:32 +08:00
|
|
|
obj-$(CONFIG_TI_K3_R5_REMOTEPROC) += ti_k3_r5_remoteproc.o
|