OpenCloudOS-Kernel/drivers/clocksource/timer-ti-dm.c

1043 lines
25 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0+
/*
* linux/arch/arm/plat-omap/dmtimer.c
*
* OMAP Dual-Mode Timers
*
* Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
* Tarun Kanti DebBarma <tarun.kanti@ti.com>
* Thara Gopinath <thara@ti.com>
*
* dmtimer adaptation to platform_driver.
*
* Copyright (C) 2005 Nokia Corporation
* OMAP2 support by Juha Yrjola
* API improvements and OMAP2 clock framework support by Timo Teras
*
* Copyright (C) 2009 Texas Instruments
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
*/
ARM: OMAP: Remove __omap_dm_timer_set_source function The __omap_dm_timer_set_source() function is only used by the system timer (clock-events and clock-source) code for OMAP2+ devices. Therefore, we can remove this code from the dmtimer driver and move it to the system timer code for OMAP2+ devices. The current __omap_dm_timer_set_source() function calls clk_disable() before calling clk_set_parent() and clk_enable() afterwards. We can avoid these calls to clk_disable/enable by moving the calls to omap_hwmod_setup_one() and omap_hwmod_enable() to after the call to clk_set_parent() in omap_dm_timer_init_one(). The function omap_hwmod_setup_one() will enable the timers functional clock and therefore increment the use-count of the functional clock to 1. clk_set_parent() will fail if the use-count is not 0 when called. Hence, if omap_hwmod_setup_one() is called before clk_set_parent(), we will need to call clk_disable() before calling clk_set_parent() to decrement the use-count. Hence, avoid these extra calls to disable and enable the functional clock by moving the calls to omap_hwmod_setup_one() and omap_hwmod_enable() to after clk_set_parent(). We can also remove the delay from the __omap_dm_timer_set_source() function because enabling the clock will now be handled via the HWMOD framework by calling omap_hwmod_setup_one(). Therefore, by moving the calls to omap_hwmod_setup_one() and omap_hwmod_enable() to after the call to clk_set_parent(), we can simply replace __omap_dm_timer_set_source() with clk_set_parent(). It should be safe to move these hwmod calls to later in the omap_dm_timer_init_one() because other calls to the hwmod layer that occur before are just requesting resource information. Testing includes boot testing on OMAP2420 H4, OMAP3430 SDP and OMAP4430 Blaze with the following configurations: 1. CONFIG_OMAP_32K_TIMER=y 2. CONFIG_OMAP_32K_TIMER=y and boot parameter "clocksource=gp_timer" 3. CONFIG_OMAP_32K_TIMER not set 4. CONFIG_OMAP_32K_TIMER not set and boot parameter "clocksource=gp_timer" Signed-off-by: Jon Hunter <jon-hunter@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
2012-09-29 00:43:30 +08:00
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/cpu_pm.h>
ARM: OMAP: dmtimer: Include linux/module.h Include linux/module.h to fix below build error: CC arch/arm/plat-omap/dmtimer.o arch/arm/plat-omap/dmtimer.c:184: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:184: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:184: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:215: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:215: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:215: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:228: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:228: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:228: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:234: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:234: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:234: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:240: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:240: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:240: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:248: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:248: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:248: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:294: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:294: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:294: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:302: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:302: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:302: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:316: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:316: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:316: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:344: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:344: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:344: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:361: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:361: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:361: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:380: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:380: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:380: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:406: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:406: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:406: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:443: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:443: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:443: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:468: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:468: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:468: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:494: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:494: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:494: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:517: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:517: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:517: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:534: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:534: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:534: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:549: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:549: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:549: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:561: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:561: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:561: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:572: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:572: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:572: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:587: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:587: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:587: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:604: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:604: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' arch/arm/plat-omap/dmtimer.c:604: warning: parameter names (without types) in function declaration arch/arm/plat-omap/dmtimer.c:746: error: expected declaration specifiers or '...' before string constant arch/arm/plat-omap/dmtimer.c:746: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:746: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION' arch/arm/plat-omap/dmtimer.c:746: warning: function declaration isn't a prototype arch/arm/plat-omap/dmtimer.c:747: error: expected declaration specifiers or '...' before string constant arch/arm/plat-omap/dmtimer.c:747: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:747: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE' arch/arm/plat-omap/dmtimer.c:747: warning: function declaration isn't a prototype arch/arm/plat-omap/dmtimer.c:748: error: expected declaration specifiers or '...' before string constant arch/arm/plat-omap/dmtimer.c:748: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:748: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS' arch/arm/plat-omap/dmtimer.c:748: warning: function declaration isn't a prototype arch/arm/plat-omap/dmtimer.c:749: error: expected declaration specifiers or '...' before string constant arch/arm/plat-omap/dmtimer.c:749: warning: data definition has no type or storage class arch/arm/plat-omap/dmtimer.c:749: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR' arch/arm/plat-omap/dmtimer.c:749: warning: function declaration isn't a prototype make[1]: *** [arch/arm/plat-omap/dmtimer.o] Error 1 make: *** [arch/arm/plat-omap] Error 2 Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-11-02 09:49:46 +08:00
#include <linux/module.h>
#include <linux/io.h>
#include <linux/device.h>
#include <linux/err.h>
#include <linux/pm_runtime.h>
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/platform_data/dmtimer-omap.h>
#include <clocksource/timer-ti-dm.h>
ARM: OMAP2+: Add dmtimer platform function to reserve systimers During early boot, one or two dmtimers are reserved by the kernel as system timers (for clocksource and clockevents). These timers are marked as reserved and the dmtimer driver is notified which timers have been reserved via the platform data information. For OMAP2+ devices the timers reserved may vary depending on device and compile flags. Therefore, it is not easy to assume which timers we be reserved for the system timers. In order to migrate the dmtimer driver to support device-tree we need a way to pass the timers reserved for system timers to the dmtimer driver. Using the platform data structure will not work in the same way as it is currently used because the platform data structure will be stored statically in the dmtimer itself and the platform data will be selected via the device-tree match device function (of_match_device). There are a couple ways to workaround this. One option is to store the system timers reserved for the kernel in the device-tree and query them on boot. The downside of this approach is that it adds some delay to parse the DT blob to search for the system timers. Secondly, for OMAP3 devices we have a dependency on compile time flags and the device-tree would not be aware of that kernel compile flags and so we would need to address that. The second option is to add a function to the dmtimer code to reserved the system timers during boot and so the dmtimer knows exactly which timers are being used for system timers. This also allows us to remove the "reserved" member from the timer platform data. This seemed like the simpler approach and so was implemented here. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-06-06 01:34:51 +08:00
static u32 omap_reserved_systimers;
static LIST_HEAD(omap_timer_list);
static DEFINE_SPINLOCK(dm_timer_lock);
enum {
REQUEST_ANY = 0,
REQUEST_BY_ID,
REQUEST_BY_CAP,
REQUEST_BY_NODE,
};
static inline u32 __omap_dm_timer_read(struct omap_dm_timer *timer, u32 reg,
int posted)
{
if (posted)
while (readl_relaxed(timer->pend) & (reg >> WPSHIFT))
cpu_relax();
return readl_relaxed(timer->func_base + (reg & 0xff));
}
static inline void __omap_dm_timer_write(struct omap_dm_timer *timer,
u32 reg, u32 val, int posted)
{
if (posted)
while (readl_relaxed(timer->pend) & (reg >> WPSHIFT))
cpu_relax();
writel_relaxed(val, timer->func_base + (reg & 0xff));
}
static inline void __omap_dm_timer_init_regs(struct omap_dm_timer *timer)
{
u32 tidr;
/* Assume v1 ip if bits [31:16] are zero */
tidr = readl_relaxed(timer->io_base);
if (!(tidr >> 16)) {
timer->revision = 1;
timer->irq_stat = timer->io_base + OMAP_TIMER_V1_STAT_OFFSET;
timer->irq_ena = timer->io_base + OMAP_TIMER_V1_INT_EN_OFFSET;
timer->irq_dis = timer->io_base + OMAP_TIMER_V1_INT_EN_OFFSET;
timer->pend = timer->io_base + _OMAP_TIMER_WRITE_PEND_OFFSET;
timer->func_base = timer->io_base;
} else {
timer->revision = 2;
timer->irq_stat = timer->io_base + OMAP_TIMER_V2_IRQSTATUS;
timer->irq_ena = timer->io_base + OMAP_TIMER_V2_IRQENABLE_SET;
timer->irq_dis = timer->io_base + OMAP_TIMER_V2_IRQENABLE_CLR;
timer->pend = timer->io_base +
_OMAP_TIMER_WRITE_PEND_OFFSET +
OMAP_TIMER_V2_FUNC_OFFSET;
timer->func_base = timer->io_base + OMAP_TIMER_V2_FUNC_OFFSET;
}
}
/*
* __omap_dm_timer_enable_posted - enables write posted mode
* @timer: pointer to timer instance handle
*
* Enables the write posted mode for the timer. When posted mode is enabled
* writes to certain timer registers are immediately acknowledged by the
* internal bus and hence prevents stalling the CPU waiting for the write to
* complete. Enabling this feature can improve performance for writing to the
* timer registers.
*/
static inline void __omap_dm_timer_enable_posted(struct omap_dm_timer *timer)
{
if (timer->posted)
return;
if (timer->errata & OMAP_TIMER_ERRATA_I103_I767) {
timer->posted = OMAP_TIMER_NONPOSTED;
__omap_dm_timer_write(timer, OMAP_TIMER_IF_CTRL_REG, 0, 0);
return;
}
__omap_dm_timer_write(timer, OMAP_TIMER_IF_CTRL_REG,
OMAP_TIMER_CTRL_POSTED, 0);
timer->context.tsicr = OMAP_TIMER_CTRL_POSTED;
timer->posted = OMAP_TIMER_POSTED;
}
static inline void __omap_dm_timer_stop(struct omap_dm_timer *timer,
int posted, unsigned long rate)
{
u32 l;
l = __omap_dm_timer_read(timer, OMAP_TIMER_CTRL_REG, posted);
if (l & OMAP_TIMER_CTRL_ST) {
l &= ~0x1;
__omap_dm_timer_write(timer, OMAP_TIMER_CTRL_REG, l, posted);
#ifdef CONFIG_ARCH_OMAP2PLUS
/* Readback to make sure write has completed */
__omap_dm_timer_read(timer, OMAP_TIMER_CTRL_REG, posted);
/*
* Wait for functional clock period x 3.5 to make sure that
* timer is stopped
*/
udelay(3500000 / rate + 1);
#endif
}
/* Ack possibly pending interrupt */
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, timer->irq_stat);
}
static inline void __omap_dm_timer_int_enable(struct omap_dm_timer *timer,
unsigned int value)
{
writel_relaxed(value, timer->irq_ena);
__omap_dm_timer_write(timer, OMAP_TIMER_WAKEUP_EN_REG, value, 0);
}
static inline unsigned int
__omap_dm_timer_read_counter(struct omap_dm_timer *timer, int posted)
{
return __omap_dm_timer_read(timer, OMAP_TIMER_COUNTER_REG, posted);
}
static inline void __omap_dm_timer_write_status(struct omap_dm_timer *timer,
unsigned int value)
{
writel_relaxed(value, timer->irq_stat);
}
/**
* omap_dm_timer_read_reg - read timer registers in posted and non-posted mode
* @timer: timer pointer over which read operation to perform
* @reg: lowest byte holds the register offset
*
* The posted mode bit is encoded in reg. Note that in posted mode write
* pending bit must be checked. Otherwise a read of a non completed write
* will produce an error.
*/
static inline u32 omap_dm_timer_read_reg(struct omap_dm_timer *timer, u32 reg)
{
WARN_ON((reg & 0xff) < _OMAP_TIMER_WAKEUP_EN_OFFSET);
return __omap_dm_timer_read(timer, reg, timer->posted);
}
/**
* omap_dm_timer_write_reg - write timer registers in posted and non-posted mode
* @timer: timer pointer over which write operation is to perform
* @reg: lowest byte holds the register offset
* @value: data to write into the register
*
* The posted mode bit is encoded in reg. Note that in posted mode the write
* pending bit must be checked. Otherwise a write on a register which has a
* pending write will be lost.
*/
static void omap_dm_timer_write_reg(struct omap_dm_timer *timer, u32 reg,
u32 value)
{
WARN_ON((reg & 0xff) < _OMAP_TIMER_WAKEUP_EN_OFFSET);
__omap_dm_timer_write(timer, reg, value, timer->posted);
}
static void omap_timer_restore_context(struct omap_dm_timer *timer)
{
__omap_dm_timer_write(timer, OMAP_TIMER_OCP_CFG_OFFSET,
timer->context.ocp_cfg, 0);
omap_dm_timer_write_reg(timer, OMAP_TIMER_WAKEUP_EN_REG,
timer->context.twer);
omap_dm_timer_write_reg(timer, OMAP_TIMER_COUNTER_REG,
timer->context.tcrr);
omap_dm_timer_write_reg(timer, OMAP_TIMER_LOAD_REG,
timer->context.tldr);
omap_dm_timer_write_reg(timer, OMAP_TIMER_MATCH_REG,
timer->context.tmar);
omap_dm_timer_write_reg(timer, OMAP_TIMER_IF_CTRL_REG,
timer->context.tsicr);
writel_relaxed(timer->context.tier, timer->irq_ena);
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG,
timer->context.tclr);
}
static void omap_timer_save_context(struct omap_dm_timer *timer)
{
timer->context.ocp_cfg =
__omap_dm_timer_read(timer, OMAP_TIMER_OCP_CFG_OFFSET, 0);
timer->context.tclr =
omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
timer->context.twer =
omap_dm_timer_read_reg(timer, OMAP_TIMER_WAKEUP_EN_REG);
timer->context.tldr =
omap_dm_timer_read_reg(timer, OMAP_TIMER_LOAD_REG);
timer->context.tmar =
omap_dm_timer_read_reg(timer, OMAP_TIMER_MATCH_REG);
timer->context.tier = readl_relaxed(timer->irq_ena);
timer->context.tsicr =
omap_dm_timer_read_reg(timer, OMAP_TIMER_IF_CTRL_REG);
}
static int omap_timer_context_notifier(struct notifier_block *nb,
unsigned long cmd, void *v)
{
struct omap_dm_timer *timer;
timer = container_of(nb, struct omap_dm_timer, nb);
switch (cmd) {
case CPU_CLUSTER_PM_ENTER:
if ((timer->capability & OMAP_TIMER_ALWON) ||
!atomic_read(&timer->enabled))
break;
omap_timer_save_context(timer);
break;
case CPU_CLUSTER_PM_ENTER_FAILED: /* No need to restore context */
break;
case CPU_CLUSTER_PM_EXIT:
if ((timer->capability & OMAP_TIMER_ALWON) ||
!atomic_read(&timer->enabled))
break;
omap_timer_restore_context(timer);
break;
}
return NOTIFY_OK;
}
static int omap_dm_timer_reset(struct omap_dm_timer *timer)
{
u32 l, timeout = 100000;
if (timer->revision != 1)
return -EINVAL;
omap_dm_timer_write_reg(timer, OMAP_TIMER_IF_CTRL_REG, 0x06);
do {
l = __omap_dm_timer_read(timer,
OMAP_TIMER_V1_SYS_STAT_OFFSET, 0);
} while (!l && timeout--);
if (!timeout) {
dev_err(&timer->pdev->dev, "Timer failed to reset\n");
return -ETIMEDOUT;
}
/* Configure timer for smart-idle mode */
l = __omap_dm_timer_read(timer, OMAP_TIMER_OCP_CFG_OFFSET, 0);
l |= 0x2 << 0x3;
__omap_dm_timer_write(timer, OMAP_TIMER_OCP_CFG_OFFSET, l, 0);
timer->posted = 0;
return 0;
}
static int omap_dm_timer_set_source(struct omap_dm_timer *timer, int source)
{
int ret;
const char *parent_name;
struct clk *parent;
struct dmtimer_platform_data *pdata;
if (unlikely(!timer) || IS_ERR(timer->fclk))
return -EINVAL;
switch (source) {
case OMAP_TIMER_SRC_SYS_CLK:
parent_name = "timer_sys_ck";
break;
case OMAP_TIMER_SRC_32_KHZ:
parent_name = "timer_32k_ck";
break;
case OMAP_TIMER_SRC_EXT_CLK:
parent_name = "timer_ext_ck";
break;
default:
return -EINVAL;
}
pdata = timer->pdev->dev.platform_data;
/*
* FIXME: Used for OMAP1 devices only because they do not currently
* use the clock framework to set the parent clock. To be removed
* once OMAP1 migrated to using clock framework for dmtimers
*/
if (pdata && pdata->set_timer_src)
return pdata->set_timer_src(timer->pdev, source);
#if defined(CONFIG_COMMON_CLK)
/* Check if the clock has configurable parents */
if (clk_hw_get_num_parents(__clk_get_hw(timer->fclk)) < 2)
return 0;
#endif
parent = clk_get(&timer->pdev->dev, parent_name);
if (IS_ERR(parent)) {
pr_err("%s: %s not found\n", __func__, parent_name);
return -EINVAL;
}
ret = clk_set_parent(timer->fclk, parent);
if (ret < 0)
pr_err("%s: failed to set %s as parent\n", __func__,
parent_name);
clk_put(parent);
return ret;
}
static void omap_dm_timer_enable(struct omap_dm_timer *timer)
{
pm_runtime_get_sync(&timer->pdev->dev);
}
static void omap_dm_timer_disable(struct omap_dm_timer *timer)
{
pm_runtime_put_sync(&timer->pdev->dev);
}
static int omap_dm_timer_prepare(struct omap_dm_timer *timer)
{
int rc;
/*
* FIXME: OMAP1 devices do not use the clock framework for dmtimers so
* do not call clk_get() for these devices.
*/
if (!(timer->capability & OMAP_TIMER_NEEDS_RESET)) {
timer->fclk = clk_get(&timer->pdev->dev, "fck");
if (WARN_ON_ONCE(IS_ERR(timer->fclk))) {
dev_err(&timer->pdev->dev, ": No fclk handle.\n");
return -EINVAL;
}
}
omap_dm_timer_enable(timer);
if (timer->capability & OMAP_TIMER_NEEDS_RESET) {
rc = omap_dm_timer_reset(timer);
if (rc) {
omap_dm_timer_disable(timer);
return rc;
}
}
__omap_dm_timer_enable_posted(timer);
omap_dm_timer_disable(timer);
return 0;
}
ARM: OMAP2+: Add dmtimer platform function to reserve systimers During early boot, one or two dmtimers are reserved by the kernel as system timers (for clocksource and clockevents). These timers are marked as reserved and the dmtimer driver is notified which timers have been reserved via the platform data information. For OMAP2+ devices the timers reserved may vary depending on device and compile flags. Therefore, it is not easy to assume which timers we be reserved for the system timers. In order to migrate the dmtimer driver to support device-tree we need a way to pass the timers reserved for system timers to the dmtimer driver. Using the platform data structure will not work in the same way as it is currently used because the platform data structure will be stored statically in the dmtimer itself and the platform data will be selected via the device-tree match device function (of_match_device). There are a couple ways to workaround this. One option is to store the system timers reserved for the kernel in the device-tree and query them on boot. The downside of this approach is that it adds some delay to parse the DT blob to search for the system timers. Secondly, for OMAP3 devices we have a dependency on compile time flags and the device-tree would not be aware of that kernel compile flags and so we would need to address that. The second option is to add a function to the dmtimer code to reserved the system timers during boot and so the dmtimer knows exactly which timers are being used for system timers. This also allows us to remove the "reserved" member from the timer platform data. This seemed like the simpler approach and so was implemented here. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-06-06 01:34:51 +08:00
static inline u32 omap_dm_timer_reserved_systimer(int id)
{
return (omap_reserved_systimers & (1 << (id - 1))) ? 1 : 0;
}
static struct omap_dm_timer *_omap_dm_timer_request(int req_type, void *data)
{
struct omap_dm_timer *timer = NULL, *t;
struct device_node *np = NULL;
unsigned long flags;
u32 cap = 0;
int id = 0;
switch (req_type) {
case REQUEST_BY_ID:
id = *(int *)data;
break;
case REQUEST_BY_CAP:
cap = *(u32 *)data;
break;
case REQUEST_BY_NODE:
np = (struct device_node *)data;
break;
default:
/* REQUEST_ANY */
break;
}
spin_lock_irqsave(&dm_timer_lock, flags);
list_for_each_entry(t, &omap_timer_list, node) {
if (t->reserved)
continue;
switch (req_type) {
case REQUEST_BY_ID:
if (id == t->pdev->id) {
timer = t;
timer->reserved = 1;
goto found;
}
break;
case REQUEST_BY_CAP:
if (cap == (t->capability & cap)) {
/*
* If timer is not NULL, we have already found
* one timer. But it was not an exact match
* because it had more capabilities than what
* was required. Therefore, unreserve the last
* timer found and see if this one is a better
* match.
*/
if (timer)
timer->reserved = 0;
timer = t;
timer->reserved = 1;
/* Exit loop early if we find an exact match */
if (t->capability == cap)
goto found;
}
break;
case REQUEST_BY_NODE:
if (np == t->pdev->dev.of_node) {
timer = t;
timer->reserved = 1;
goto found;
}
break;
default:
/* REQUEST_ANY */
timer = t;
timer->reserved = 1;
goto found;
}
}
found:
spin_unlock_irqrestore(&dm_timer_lock, flags);
if (timer && omap_dm_timer_prepare(timer)) {
timer->reserved = 0;
timer = NULL;
}
if (!timer)
pr_debug("%s: timer request failed!\n", __func__);
return timer;
}
static struct omap_dm_timer *omap_dm_timer_request(void)
{
return _omap_dm_timer_request(REQUEST_ANY, NULL);
}
static struct omap_dm_timer *omap_dm_timer_request_specific(int id)
{
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
/* Requesting timer by ID is not supported when device tree is used */
if (of_have_populated_dt()) {
pr_warn("%s: Please use omap_dm_timer_request_by_node()\n",
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
__func__);
return NULL;
}
return _omap_dm_timer_request(REQUEST_BY_ID, &id);
}
/**
* omap_dm_timer_request_by_node - Request a timer by device-tree node
* @np: Pointer to device-tree timer node
*
* Request a timer based upon a device node pointer. Returns pointer to
* timer handle on success and a NULL pointer on failure.
*/
static struct omap_dm_timer *omap_dm_timer_request_by_node(struct device_node *np)
{
if (!np)
return NULL;
return _omap_dm_timer_request(REQUEST_BY_NODE, np);
}
static int omap_dm_timer_free(struct omap_dm_timer *timer)
{
if (unlikely(!timer))
return -EINVAL;
clk_put(timer->fclk);
WARN_ON(!timer->reserved);
timer->reserved = 0;
return 0;
}
int omap_dm_timer_get_irq(struct omap_dm_timer *timer)
{
if (timer)
return timer->irq;
return -EINVAL;
}
#if defined(CONFIG_ARCH_OMAP1)
#include <linux/soc/ti/omap1-io.h>
static struct clk *omap_dm_timer_get_fclk(struct omap_dm_timer *timer)
{
return NULL;
}
/**
* omap_dm_timer_modify_idlect_mask - Check if any running timers use ARMXOR
* @inputmask: current value of idlect mask
*/
__u32 omap_dm_timer_modify_idlect_mask(__u32 inputmask)
{
int i = 0;
struct omap_dm_timer *timer = NULL;
unsigned long flags;
/* If ARMXOR cannot be idled this function call is unnecessary */
if (!(inputmask & (1 << 1)))
return inputmask;
/* If any active timer is using ARMXOR return modified mask */
spin_lock_irqsave(&dm_timer_lock, flags);
list_for_each_entry(timer, &omap_timer_list, node) {
u32 l;
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
if (l & OMAP_TIMER_CTRL_ST) {
if (((omap_readl(MOD_CONF_CTRL_1) >> (i * 2)) & 0x03) == 0)
inputmask &= ~(1 << 1);
else
inputmask &= ~(1 << 2);
}
i++;
}
spin_unlock_irqrestore(&dm_timer_lock, flags);
return inputmask;
}
#else
static struct clk *omap_dm_timer_get_fclk(struct omap_dm_timer *timer)
{
if (timer && !IS_ERR(timer->fclk))
return timer->fclk;
return NULL;
}
__u32 omap_dm_timer_modify_idlect_mask(__u32 inputmask)
{
BUG();
return 0;
}
#endif
static int omap_dm_timer_start(struct omap_dm_timer *timer)
{
u32 l;
if (unlikely(!timer))
return -EINVAL;
omap_dm_timer_enable(timer);
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
if (!(l & OMAP_TIMER_CTRL_ST)) {
l |= OMAP_TIMER_CTRL_ST;
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
}
return 0;
}
static int omap_dm_timer_stop(struct omap_dm_timer *timer)
{
unsigned long rate = 0;
if (unlikely(!timer))
return -EINVAL;
if (!(timer->capability & OMAP_TIMER_NEEDS_RESET))
rate = clk_get_rate(timer->fclk);
__omap_dm_timer_stop(timer, timer->posted, rate);
omap_dm_timer_disable(timer);
return 0;
}
static int omap_dm_timer_set_load(struct omap_dm_timer *timer,
unsigned int load)
{
if (unlikely(!timer))
return -EINVAL;
omap_dm_timer_enable(timer);
omap_dm_timer_write_reg(timer, OMAP_TIMER_LOAD_REG, load);
omap_dm_timer_disable(timer);
return 0;
}
static int omap_dm_timer_set_match(struct omap_dm_timer *timer, int enable,
unsigned int match)
{
u32 l;
if (unlikely(!timer))
return -EINVAL;
omap_dm_timer_enable(timer);
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
if (enable)
l |= OMAP_TIMER_CTRL_CE;
else
l &= ~OMAP_TIMER_CTRL_CE;
omap_dm_timer_write_reg(timer, OMAP_TIMER_MATCH_REG, match);
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
omap_dm_timer_disable(timer);
return 0;
}
static int omap_dm_timer_set_pwm(struct omap_dm_timer *timer, int def_on,
int toggle, int trigger, int autoreload)
{
u32 l;
if (unlikely(!timer))
return -EINVAL;
omap_dm_timer_enable(timer);
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
l &= ~(OMAP_TIMER_CTRL_GPOCFG | OMAP_TIMER_CTRL_SCPWM |
OMAP_TIMER_CTRL_PT | (0x03 << 10) | OMAP_TIMER_CTRL_AR);
if (def_on)
l |= OMAP_TIMER_CTRL_SCPWM;
if (toggle)
l |= OMAP_TIMER_CTRL_PT;
l |= trigger << 10;
if (autoreload)
l |= OMAP_TIMER_CTRL_AR;
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
omap_dm_timer_disable(timer);
return 0;
}
static int omap_dm_timer_get_pwm_status(struct omap_dm_timer *timer)
{
u32 l;
if (unlikely(!timer))
return -EINVAL;
omap_dm_timer_enable(timer);
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
omap_dm_timer_disable(timer);
return l;
}
static int omap_dm_timer_set_prescaler(struct omap_dm_timer *timer,
int prescaler)
{
u32 l;
if (unlikely(!timer) || prescaler < -1 || prescaler > 7)
return -EINVAL;
omap_dm_timer_enable(timer);
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
l &= ~(OMAP_TIMER_CTRL_PRE | (0x07 << 2));
if (prescaler >= 0) {
l |= OMAP_TIMER_CTRL_PRE;
l |= prescaler << 2;
}
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
omap_dm_timer_disable(timer);
return 0;
}
static int omap_dm_timer_set_int_enable(struct omap_dm_timer *timer,
unsigned int value)
{
if (unlikely(!timer))
return -EINVAL;
omap_dm_timer_enable(timer);
__omap_dm_timer_int_enable(timer, value);
omap_dm_timer_disable(timer);
return 0;
}
/**
* omap_dm_timer_set_int_disable - disable timer interrupts
* @timer: pointer to timer handle
* @mask: bit mask of interrupts to be disabled
*
* Disables the specified timer interrupts for a timer.
*/
static int omap_dm_timer_set_int_disable(struct omap_dm_timer *timer, u32 mask)
{
u32 l = mask;
if (unlikely(!timer))
return -EINVAL;
omap_dm_timer_enable(timer);
if (timer->revision == 1)
l = readl_relaxed(timer->irq_ena) & ~mask;
writel_relaxed(l, timer->irq_dis);
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_WAKEUP_EN_REG) & ~mask;
omap_dm_timer_write_reg(timer, OMAP_TIMER_WAKEUP_EN_REG, l);
omap_dm_timer_disable(timer);
return 0;
}
static unsigned int omap_dm_timer_read_status(struct omap_dm_timer *timer)
{
unsigned int l;
if (unlikely(!timer || !atomic_read(&timer->enabled))) {
pr_err("%s: timer not available or enabled.\n", __func__);
return 0;
}
l = readl_relaxed(timer->irq_stat);
return l;
}
static int omap_dm_timer_write_status(struct omap_dm_timer *timer, unsigned int value)
{
if (unlikely(!timer || !atomic_read(&timer->enabled)))
return -EINVAL;
__omap_dm_timer_write_status(timer, value);
return 0;
}
static unsigned int omap_dm_timer_read_counter(struct omap_dm_timer *timer)
{
if (unlikely(!timer || !atomic_read(&timer->enabled))) {
pr_err("%s: timer not iavailable or enabled.\n", __func__);
return 0;
}
return __omap_dm_timer_read_counter(timer, timer->posted);
}
static int omap_dm_timer_write_counter(struct omap_dm_timer *timer, unsigned int value)
{
if (unlikely(!timer || !atomic_read(&timer->enabled))) {
pr_err("%s: timer not available or enabled.\n", __func__);
return -EINVAL;
}
omap_dm_timer_write_reg(timer, OMAP_TIMER_COUNTER_REG, value);
/* Save the context */
timer->context.tcrr = value;
return 0;
}
static int __maybe_unused omap_dm_timer_runtime_suspend(struct device *dev)
{
struct omap_dm_timer *timer = dev_get_drvdata(dev);
atomic_set(&timer->enabled, 0);
if (timer->capability & OMAP_TIMER_ALWON || !timer->func_base)
return 0;
omap_timer_save_context(timer);
return 0;
}
static int __maybe_unused omap_dm_timer_runtime_resume(struct device *dev)
{
struct omap_dm_timer *timer = dev_get_drvdata(dev);
if (!(timer->capability & OMAP_TIMER_ALWON) && timer->func_base)
omap_timer_restore_context(timer);
atomic_set(&timer->enabled, 1);
return 0;
}
static const struct dev_pm_ops omap_dm_timer_pm_ops = {
SET_RUNTIME_PM_OPS(omap_dm_timer_runtime_suspend,
omap_dm_timer_runtime_resume, NULL)
};
static const struct of_device_id omap_timer_match[];
/**
* omap_dm_timer_probe - probe function called for every registered device
* @pdev: pointer to current timer platform device
*
* Called by driver framework at the end of device registration for all
* timer devices.
*/
static int omap_dm_timer_probe(struct platform_device *pdev)
{
unsigned long flags;
struct omap_dm_timer *timer;
struct device *dev = &pdev->dev;
const struct dmtimer_platform_data *pdata;
int ret;
pdata = of_device_get_match_data(dev);
if (!pdata)
pdata = dev_get_platdata(dev);
else
dev->platform_data = (void *)pdata;
if (!pdata) {
dev_err(dev, "%s: no platform data.\n", __func__);
return -ENODEV;
}
timer = devm_kzalloc(dev, sizeof(*timer), GFP_KERNEL);
if (!timer)
return -ENOMEM;
timer->irq = platform_get_irq(pdev, 0);
if (timer->irq < 0)
return timer->irq;
timer->fclk = ERR_PTR(-ENODEV);
timer->io_base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(timer->io_base))
return PTR_ERR(timer->io_base);
platform_set_drvdata(pdev, timer);
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
if (dev->of_node) {
if (of_find_property(dev->of_node, "ti,timer-alwon", NULL))
timer->capability |= OMAP_TIMER_ALWON;
if (of_find_property(dev->of_node, "ti,timer-dsp", NULL))
timer->capability |= OMAP_TIMER_HAS_DSP_IRQ;
if (of_find_property(dev->of_node, "ti,timer-pwm", NULL))
timer->capability |= OMAP_TIMER_HAS_PWM;
if (of_find_property(dev->of_node, "ti,timer-secure", NULL))
timer->capability |= OMAP_TIMER_SECURE;
} else {
timer->id = pdev->id;
timer->capability = pdata->timer_capability;
timer->reserved = omap_dm_timer_reserved_systimer(timer->id);
}
if (!(timer->capability & OMAP_TIMER_ALWON)) {
timer->nb.notifier_call = omap_timer_context_notifier;
cpu_pm_register_notifier(&timer->nb);
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
}
timer->errata = pdata->timer_errata;
timer->pdev = pdev;
pm_runtime_enable(dev);
if (!timer->reserved) {
ret = pm_runtime_get_sync(dev);
if (ret < 0) {
dev_err(dev, "%s: pm_runtime_get_sync failed!\n",
__func__);
goto err_get_sync;
}
__omap_dm_timer_init_regs(timer);
pm_runtime_put(dev);
}
/* add the timer element to the list */
spin_lock_irqsave(&dm_timer_lock, flags);
list_add_tail(&timer->node, &omap_timer_list);
spin_unlock_irqrestore(&dm_timer_lock, flags);
dev_dbg(dev, "Device Probed.\n");
return 0;
err_get_sync:
pm_runtime_put_noidle(dev);
pm_runtime_disable(dev);
return ret;
}
/**
* omap_dm_timer_remove - cleanup a registered timer device
* @pdev: pointer to current timer platform device
*
* Called by driver framework whenever a timer device is unregistered.
* In addition to freeing platform resources it also deletes the timer
* entry from the local list.
*/
static int omap_dm_timer_remove(struct platform_device *pdev)
{
struct omap_dm_timer *timer;
unsigned long flags;
int ret = -EINVAL;
spin_lock_irqsave(&dm_timer_lock, flags);
list_for_each_entry(timer, &omap_timer_list, node)
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
if (!strcmp(dev_name(&timer->pdev->dev),
dev_name(&pdev->dev))) {
if (!(timer->capability & OMAP_TIMER_ALWON))
cpu_pm_unregister_notifier(&timer->nb);
list_del(&timer->node);
ret = 0;
break;
}
spin_unlock_irqrestore(&dm_timer_lock, flags);
pm_runtime_disable(&pdev->dev);
return ret;
}
static const struct omap_dm_timer_ops dmtimer_ops = {
.request_by_node = omap_dm_timer_request_by_node,
.request_specific = omap_dm_timer_request_specific,
.request = omap_dm_timer_request,
.set_source = omap_dm_timer_set_source,
.get_irq = omap_dm_timer_get_irq,
.set_int_enable = omap_dm_timer_set_int_enable,
.set_int_disable = omap_dm_timer_set_int_disable,
.free = omap_dm_timer_free,
.enable = omap_dm_timer_enable,
.disable = omap_dm_timer_disable,
.get_fclk = omap_dm_timer_get_fclk,
.start = omap_dm_timer_start,
.stop = omap_dm_timer_stop,
.set_load = omap_dm_timer_set_load,
.set_match = omap_dm_timer_set_match,
.set_pwm = omap_dm_timer_set_pwm,
.get_pwm_status = omap_dm_timer_get_pwm_status,
.set_prescaler = omap_dm_timer_set_prescaler,
.read_counter = omap_dm_timer_read_counter,
.write_counter = omap_dm_timer_write_counter,
.read_status = omap_dm_timer_read_status,
.write_status = omap_dm_timer_write_status,
};
static const struct dmtimer_platform_data omap3plus_pdata = {
.timer_errata = OMAP_TIMER_ERRATA_I103_I767,
.timer_ops = &dmtimer_ops,
};
static const struct dmtimer_platform_data am6_pdata = {
.timer_ops = &dmtimer_ops,
};
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
static const struct of_device_id omap_timer_match[] = {
{
.compatible = "ti,omap2420-timer",
},
{
.compatible = "ti,omap3430-timer",
.data = &omap3plus_pdata,
},
{
.compatible = "ti,omap4430-timer",
.data = &omap3plus_pdata,
},
{
.compatible = "ti,omap5430-timer",
.data = &omap3plus_pdata,
},
{
.compatible = "ti,am335x-timer",
.data = &omap3plus_pdata,
},
{
.compatible = "ti,am335x-timer-1ms",
.data = &omap3plus_pdata,
},
{
.compatible = "ti,dm816-timer",
.data = &omap3plus_pdata,
},
{
.compatible = "ti,am654-timer",
.data = &am6_pdata,
},
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
{},
};
MODULE_DEVICE_TABLE(of, omap_timer_match);
static struct platform_driver omap_dm_timer_driver = {
.probe = omap_dm_timer_probe,
.remove = omap_dm_timer_remove,
.driver = {
.name = "omap_timer",
ARM: OMAP: Add DT support for timer driver In order to add device-tree support to the timer driver the following changes were made ... 1. Allocate system timers (used for clock-events and clock-source) based upon timer properties rather than using an hard-coded timer instance ID. To allow this a new helper function called omap_dmtimer_find_by_property() has been added for finding a timer with the particular properties in the device-tree blob. Please note that this is an internal helper function for system timers only to find a timer in the device-tree blob. This cannot be used by device drivers, another API has been added for that (see below). Timers that are allocated for system timers are dynamically disabled at boot time by adding a status property with the value "disabled" to the timer's device-tree node. Please note that when allocating system timers we now pass a timer ID and timer property. The timer ID is only be used for allocating a timer when booting without device-tree. Once device-tree migration is complete, all the timer ID references will be removed. 2. System timer resources (memory and interrupts) are directly obtained from the device-tree timer node when booting with device-tree, so that system timers are no longer reliant upon the OMAP HWMOD framework to provide these resources. 3. If DT blob is present, then let device-tree create the timer devices dynamically. 4. When device-tree is present the "id" field in the platform_device structure (pdev->id) is initialised to -1 and hence cannot be used to identify a timer instance. Due to this the following changes were made ... a). The API omap_dm_timer_request_specific() is not supported when using device-tree, because it uses the device ID to request a specific timer. This function will return an error if called when device-tree is present. Users of this API should use omap_dm_timer_request_by_cap() instead. b). When removing the DMTIMER driver, the timer "id" was used to identify the timer instance. The remove function has been modified to use the device name instead of the "id". 5. When device-tree is present the platform_data structure will be NULL and so check for this. 6. The OMAP timer device tree binding has the following optional parameters ... a). ti,timer-alwon --> Timer is in an always-on power domain b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP c). ti,timer-pwm --> Timer can generate a PWM output d). ti,timer-secure --> Timer is reserved on a secure OMAP device Search for the above parameters and set the appropriate timer attribute flags. Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-14 23:41:37 +08:00
.of_match_table = of_match_ptr(omap_timer_match),
.pm = &omap_dm_timer_pm_ops,
},
};
module_platform_driver(omap_dm_timer_driver);
MODULE_DESCRIPTION("OMAP Dual-Mode Timer Driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Texas Instruments Inc");