OpenCloudOS-Kernel/arch/x86/xen/setup.c

867 lines
24 KiB
C
Raw Normal View History

xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
/*
* Machine specific setup for xen
*
* Jeremy Fitzhardinge <jeremy@xensource.com>, XenSource Inc, 2007
*/
#include <linux/module.h>
#include <linux/sched.h>
#include <linux/mm.h>
#include <linux/pm.h>
#include <linux/memblock.h>
#include <linux/cpuidle.h>
#include <linux/cpufreq.h>
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
#include <asm/elf.h>
#include <asm/vdso.h>
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
#include <asm/e820.h>
#include <asm/setup.h>
#include <asm/acpi.h>
xen/boot: Disable NUMA for PV guests. The hypervisor is in charge of allocating the proper "NUMA" memory and dealing with the CPU scheduler to keep them bound to the proper NUMA node. The PV guests (and PVHVM) have no inkling of where they run and do not need to know that right now. In the future we will need to inject NUMA configuration data (if a guest spans two or more NUMA nodes) so that the kernel can make the right choices. But those patches are not yet present. In the meantime, disable the NUMA capability in the PV guest, which also fixes a bootup issue. Andre says: "we see Dom0 crashes due to the kernel detecting the NUMA topology not by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA). This will detect the actual NUMA config of the physical machine, but will crash about the mismatch with Dom0's virtual memory. Variation of the theme: Dom0 sees what it's not supposed to see. This happens with the said config option enabled and on a machine where this scanning is still enabled (K8 and Fam10h, not Bulldozer class) We have this dump then: NUMA: Warning: node ids are out of bound, from=-1 to=-1 distance=10 Scanning NUMA topology in Northbridge 24 Number of physical nodes 4 Node 0 MemBase 0000000000000000 Limit 0000000040000000 Node 1 MemBase 0000000040000000 Limit 0000000138000000 Node 2 MemBase 0000000138000000 Limit 00000001f8000000 Node 3 MemBase 00000001f8000000 Limit 0000000238000000 Initmem setup node 0 0000000000000000-0000000040000000 NODE_DATA [000000003ffd9000 - 000000003fffffff] Initmem setup node 1 0000000040000000-0000000138000000 NODE_DATA [0000000137fd9000 - 0000000137ffffff] Initmem setup node 2 0000000138000000-00000001f8000000 NODE_DATA [00000001f095e000 - 00000001f0984fff] Initmem setup node 3 00000001f8000000-0000000238000000 Cannot find 159744 bytes in node 3 BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96 Pid: 0, comm: swapper Not tainted 3.3.6 #1 AMD Dinar/Dinar RIP: e030:[<ffffffff81d220e6>] [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96 .. snip.. [<ffffffff81d23024>] sparse_early_usemaps_alloc_node+0x64/0x178 [<ffffffff81d23348>] sparse_init+0xe4/0x25a [<ffffffff81d16840>] paging_init+0x13/0x22 [<ffffffff81d07fbb>] setup_arch+0x9c6/0xa9b [<ffffffff81683954>] ? printk+0x3c/0x3e [<ffffffff81d01a38>] start_kernel+0xe5/0x468 [<ffffffff81d012cf>] x86_64_start_reservations+0xba/0xc1 [<ffffffff81007153>] ? xen_setup_runstate_info+0x2c/0x36 [<ffffffff81d050ee>] xen_start_kernel+0x565/0x56c " so we just disable NUMA scanning by setting numa_off=1. CC: stable@vger.kernel.org Reported-and-Tested-by: Andre Przywara <andre.przywara@amd.com> Acked-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-08-17 22:22:37 +08:00
#include <asm/numa.h>
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
#include <asm/xen/hypervisor.h>
#include <asm/xen/hypercall.h>
#include <xen/xen.h>
#include <xen/page.h>
#include <xen/interface/callback.h>
#include <xen/interface/memory.h>
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
#include <xen/interface/physdev.h>
#include <xen/features.h>
#include "xen-ops.h"
#include "vdso.h"
#include "p2m.h"
#include "mmu.h"
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
/* These are code, but not functions. Defined in entry.S */
extern const char xen_hypervisor_callback[];
extern const char xen_failsafe_callback[];
xen: Support 64-bit PV guest receiving NMIs This is based on a patch that Zhenzhong Duan had sent - which was missing some of the remaining pieces. The kernel has the logic to handle Xen-type-exceptions using the paravirt interface in the assembler code (see PARAVIRT_ADJUST_EXCEPTION_FRAME - pv_irq_ops.adjust_exception_frame and and INTERRUPT_RETURN - pv_cpu_ops.iret). That means the nmi handler (and other exception handlers) use the hypervisor iret. The other changes that would be neccessary for this would be to translate the NMI_VECTOR to one of the entries on the ipi_vector and make xen_send_IPI_mask_allbutself use different events. Fortunately for us commit 1db01b4903639fcfaec213701a494fe3fb2c490b (xen: Clean up apic ipi interface) implemented this and we piggyback on the cleanup such that the apic IPI interface will pass the right vector value for NMI. With this patch we can trigger NMIs within a PV guest (only tested x86_64). For this to work with normal PV guests (not initial domain) we need the domain to be able to use the APIC ops - they are already implemented to use the Xen event channels. For that to be turned on in a PV domU we need to remove the masking of X86_FEATURE_APIC. Incidentally that means kgdb will also now work within a PV guest without using the 'nokgdbroundup' workaround. Note that the 32-bit version is different and this patch does not enable that. CC: Lisa Nguyen <lisa@xenapiadmin.com> CC: Ben Guthro <benjamin.guthro@citrix.com> CC: Zhenzhong Duan <zhenzhong.duan@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [v1: Fixed up per David Vrabel comments] Reviewed-by: Ben Guthro <benjamin.guthro@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
2013-07-19 23:51:31 +08:00
#ifdef CONFIG_X86_64
extern asmlinkage void nmi(void);
xen: Support 64-bit PV guest receiving NMIs This is based on a patch that Zhenzhong Duan had sent - which was missing some of the remaining pieces. The kernel has the logic to handle Xen-type-exceptions using the paravirt interface in the assembler code (see PARAVIRT_ADJUST_EXCEPTION_FRAME - pv_irq_ops.adjust_exception_frame and and INTERRUPT_RETURN - pv_cpu_ops.iret). That means the nmi handler (and other exception handlers) use the hypervisor iret. The other changes that would be neccessary for this would be to translate the NMI_VECTOR to one of the entries on the ipi_vector and make xen_send_IPI_mask_allbutself use different events. Fortunately for us commit 1db01b4903639fcfaec213701a494fe3fb2c490b (xen: Clean up apic ipi interface) implemented this and we piggyback on the cleanup such that the apic IPI interface will pass the right vector value for NMI. With this patch we can trigger NMIs within a PV guest (only tested x86_64). For this to work with normal PV guests (not initial domain) we need the domain to be able to use the APIC ops - they are already implemented to use the Xen event channels. For that to be turned on in a PV domU we need to remove the masking of X86_FEATURE_APIC. Incidentally that means kgdb will also now work within a PV guest without using the 'nokgdbroundup' workaround. Note that the 32-bit version is different and this patch does not enable that. CC: Lisa Nguyen <lisa@xenapiadmin.com> CC: Ben Guthro <benjamin.guthro@citrix.com> CC: Zhenzhong Duan <zhenzhong.duan@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [v1: Fixed up per David Vrabel comments] Reviewed-by: Ben Guthro <benjamin.guthro@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
2013-07-19 23:51:31 +08:00
#endif
extern void xen_sysenter_target(void);
extern void xen_syscall_target(void);
extern void xen_syscall32_target(void);
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
/* Amount of extra memory space we add to the e820 ranges */
struct xen_memory_region xen_extra_mem[XEN_EXTRA_MEM_MAX_REGIONS] __initdata;
/* Number of pages released from the initial allocation. */
unsigned long xen_released_pages;
/*
* Buffer used to remap identity mapped pages. We only need the virtual space.
* The physical page behind this address is remapped as needed to different
* buffer pages.
*/
#define REMAP_SIZE (P2M_PER_PAGE - 3)
static struct {
unsigned long next_area_mfn;
unsigned long target_pfn;
unsigned long size;
unsigned long mfns[REMAP_SIZE];
} xen_remap_buf __initdata __aligned(PAGE_SIZE);
static unsigned long xen_remap_mfn __initdata = INVALID_P2M_ENTRY;
/*
* The maximum amount of extra memory compared to the base size. The
* main scaling factor is the size of struct page. At extreme ratios
* of base:extra, all the base memory can be filled with page
* structures for the extra memory, leaving no space for anything
* else.
*
* 10x seems like a reasonable balance between scaling flexibility and
* leaving a practically usable system.
*/
#define EXTRA_MEM_RATIO (10)
static void __init xen_add_extra_mem(u64 start, u64 size)
{
int i;
for (i = 0; i < XEN_EXTRA_MEM_MAX_REGIONS; i++) {
/* Add new region. */
if (xen_extra_mem[i].size == 0) {
xen_extra_mem[i].start = start;
xen_extra_mem[i].size = size;
break;
}
/* Append to existing region. */
if (xen_extra_mem[i].start + xen_extra_mem[i].size == start) {
xen_extra_mem[i].size += size;
break;
}
}
if (i == XEN_EXTRA_MEM_MAX_REGIONS)
printk(KERN_WARNING "Warning: not enough extra memory regions\n");
memblock_reserve(start, size);
}
static void __init xen_del_extra_mem(u64 start, u64 size)
{
int i;
u64 start_r, size_r;
for (i = 0; i < XEN_EXTRA_MEM_MAX_REGIONS; i++) {
start_r = xen_extra_mem[i].start;
size_r = xen_extra_mem[i].size;
/* Start of region. */
if (start_r == start) {
BUG_ON(size > size_r);
xen_extra_mem[i].start += size;
xen_extra_mem[i].size -= size;
break;
}
/* End of region. */
if (start_r + size_r == start + size) {
BUG_ON(size > size_r);
xen_extra_mem[i].size -= size;
break;
}
/* Mid of region. */
if (start > start_r && start < start_r + size_r) {
BUG_ON(start + size > start_r + size_r);
xen_extra_mem[i].size = start - start_r;
/* Calling memblock_reserve() again is okay. */
xen_add_extra_mem(start + size, start_r + size_r -
(start + size));
break;
}
}
memblock_free(start, size);
}
/*
* Called during boot before the p2m list can take entries beyond the
* hypervisor supplied p2m list. Entries in extra mem are to be regarded as
* invalid.
*/
unsigned long __ref xen_chk_extra_mem(unsigned long pfn)
{
int i;
unsigned long addr = PFN_PHYS(pfn);
for (i = 0; i < XEN_EXTRA_MEM_MAX_REGIONS; i++) {
if (addr >= xen_extra_mem[i].start &&
addr < xen_extra_mem[i].start + xen_extra_mem[i].size)
return INVALID_P2M_ENTRY;
}
return IDENTITY_FRAME(pfn);
}
/*
* Mark all pfns of extra mem as invalid in p2m list.
*/
void __init xen_inv_extra_mem(void)
{
unsigned long pfn, pfn_s, pfn_e;
int i;
for (i = 0; i < XEN_EXTRA_MEM_MAX_REGIONS; i++) {
pfn_s = PFN_DOWN(xen_extra_mem[i].start);
pfn_e = PFN_UP(xen_extra_mem[i].start + xen_extra_mem[i].size);
for (pfn = pfn_s; pfn < pfn_e; pfn++)
set_phys_to_machine(pfn, INVALID_P2M_ENTRY);
}
}
/*
* Finds the next RAM pfn available in the E820 map after min_pfn.
* This function updates min_pfn with the pfn found and returns
* the size of that range or zero if not found.
*/
static unsigned long __init xen_find_pfn_range(
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
const struct e820entry *list, size_t map_size,
unsigned long *min_pfn)
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
{
const struct e820entry *entry;
unsigned int i;
unsigned long done = 0;
for (i = 0, entry = list; i < map_size; i++, entry++) {
unsigned long s_pfn;
unsigned long e_pfn;
if (entry->type != E820_RAM)
continue;
xen: populate correct number of pages when across mem boundary (v2) When populate pages across a mem boundary at bootup, the page count populated isn't correct. This is due to mem populated to non-mem region and ignored. Pfn range is also wrongly aligned when mem boundary isn't page aligned. For a dom0 booted with dom_mem=3368952K(0xcd9ff000-4k) dmesg diff is: [ 0.000000] Freeing 9e-100 pfn range: 98 pages freed [ 0.000000] 1-1 mapping on 9e->100 [ 0.000000] 1-1 mapping on cd9ff->100000 [ 0.000000] Released 98 pages of unused memory [ 0.000000] Set 206435 page(s) to 1-1 mapping -[ 0.000000] Populating cd9fe-cda00 pfn range: 1 pages added +[ 0.000000] Populating cd9fe-cd9ff pfn range: 1 pages added +[ 0.000000] Populating 100000-100061 pfn range: 97 pages added [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 000000000009e000 (usable) [ 0.000000] Xen: 00000000000a0000 - 0000000000100000 (reserved) [ 0.000000] Xen: 0000000000100000 - 00000000cd9ff000 (usable) [ 0.000000] Xen: 00000000cd9ffc00 - 00000000cda53c00 (ACPI NVS) ... [ 0.000000] Xen: 0000000100000000 - 0000000100061000 (usable) [ 0.000000] Xen: 0000000100061000 - 000000012c000000 (unusable) ... [ 0.000000] MEMBLOCK configuration: ... -[ 0.000000] reserved[0x4] [0x000000cd9ff000-0x000000cd9ffbff], 0xc00 bytes -[ 0.000000] reserved[0x5] [0x00000100000000-0x00000100060fff], 0x61000 bytes Related xen memory layout: (XEN) Xen-e820 RAM map: (XEN) 0000000000000000 - 000000000009ec00 (usable) (XEN) 00000000000f0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 00000000cd9ffc00 (usable) Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com> [v2: If xen_do_chunk fail(populate), abort this chunk and any others] Suggested by David, thanks. Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-07-18 13:06:39 +08:00
e_pfn = PFN_DOWN(entry->addr + entry->size);
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
/* We only care about E820 after this */
if (e_pfn < *min_pfn)
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
continue;
xen: populate correct number of pages when across mem boundary (v2) When populate pages across a mem boundary at bootup, the page count populated isn't correct. This is due to mem populated to non-mem region and ignored. Pfn range is also wrongly aligned when mem boundary isn't page aligned. For a dom0 booted with dom_mem=3368952K(0xcd9ff000-4k) dmesg diff is: [ 0.000000] Freeing 9e-100 pfn range: 98 pages freed [ 0.000000] 1-1 mapping on 9e->100 [ 0.000000] 1-1 mapping on cd9ff->100000 [ 0.000000] Released 98 pages of unused memory [ 0.000000] Set 206435 page(s) to 1-1 mapping -[ 0.000000] Populating cd9fe-cda00 pfn range: 1 pages added +[ 0.000000] Populating cd9fe-cd9ff pfn range: 1 pages added +[ 0.000000] Populating 100000-100061 pfn range: 97 pages added [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 000000000009e000 (usable) [ 0.000000] Xen: 00000000000a0000 - 0000000000100000 (reserved) [ 0.000000] Xen: 0000000000100000 - 00000000cd9ff000 (usable) [ 0.000000] Xen: 00000000cd9ffc00 - 00000000cda53c00 (ACPI NVS) ... [ 0.000000] Xen: 0000000100000000 - 0000000100061000 (usable) [ 0.000000] Xen: 0000000100061000 - 000000012c000000 (unusable) ... [ 0.000000] MEMBLOCK configuration: ... -[ 0.000000] reserved[0x4] [0x000000cd9ff000-0x000000cd9ffbff], 0xc00 bytes -[ 0.000000] reserved[0x5] [0x00000100000000-0x00000100060fff], 0x61000 bytes Related xen memory layout: (XEN) Xen-e820 RAM map: (XEN) 0000000000000000 - 000000000009ec00 (usable) (XEN) 00000000000f0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 00000000cd9ffc00 (usable) Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com> [v2: If xen_do_chunk fail(populate), abort this chunk and any others] Suggested by David, thanks. Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-07-18 13:06:39 +08:00
s_pfn = PFN_UP(entry->addr);
/* If min_pfn falls within the E820 entry, we want to start
* at the min_pfn PFN.
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
*/
if (s_pfn <= *min_pfn) {
done = e_pfn - *min_pfn;
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
} else {
done = e_pfn - s_pfn;
*min_pfn = s_pfn;
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
}
break;
}
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
return done;
}
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
static int __init xen_free_mfn(unsigned long mfn)
{
struct xen_memory_reservation reservation = {
.address_bits = 0,
.extent_order = 0,
.domid = DOMID_SELF
};
set_xen_guest_handle(reservation.extent_start, &mfn);
reservation.nr_extents = 1;
return HYPERVISOR_memory_op(XENMEM_decrease_reservation, &reservation);
}
/*
* This releases a chunk of memory and then does the identity map. It's used
* as a fallback if the remapping fails.
*/
static void __init xen_set_identity_and_release_chunk(unsigned long start_pfn,
unsigned long end_pfn, unsigned long nr_pages, unsigned long *released)
{
unsigned long pfn, end;
int ret;
WARN_ON(start_pfn > end_pfn);
/* Release pages first. */
end = min(end_pfn, nr_pages);
for (pfn = start_pfn; pfn < end; pfn++) {
unsigned long mfn = pfn_to_mfn(pfn);
/* Make sure pfn exists to start with */
if (mfn == INVALID_P2M_ENTRY || mfn_to_pfn(mfn) != pfn)
continue;
ret = xen_free_mfn(mfn);
WARN(ret != 1, "Failed to release pfn %lx err=%d\n", pfn, ret);
if (ret == 1) {
(*released)++;
if (!__set_phys_to_machine(pfn, INVALID_P2M_ENTRY))
break;
} else
break;
}
set_phys_range_identity(start_pfn, end_pfn);
}
/*
* Helper function to update the p2m and m2p tables and kernel mapping.
*/
static void __init xen_update_mem_tables(unsigned long pfn, unsigned long mfn)
{
struct mmu_update update = {
.ptr = ((unsigned long long)mfn << PAGE_SHIFT) | MMU_MACHPHYS_UPDATE,
.val = pfn
};
/* Update p2m */
if (!set_phys_to_machine(pfn, mfn)) {
WARN(1, "Failed to set p2m mapping for pfn=%ld mfn=%ld\n",
pfn, mfn);
BUG();
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
}
/* Update m2p */
if (HYPERVISOR_mmu_update(&update, 1, NULL, DOMID_SELF) < 0) {
WARN(1, "Failed to set m2p mapping for mfn=%ld pfn=%ld\n",
mfn, pfn);
BUG();
}
/* Update kernel mapping, but not for highmem. */
if ((pfn << PAGE_SHIFT) >= __pa(high_memory))
return;
if (HYPERVISOR_update_va_mapping((unsigned long)__va(pfn << PAGE_SHIFT),
mfn_pte(mfn, PAGE_KERNEL), 0)) {
WARN(1, "Failed to update kernel mapping for mfn=%ld pfn=%ld\n",
mfn, pfn);
BUG();
}
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
}
/*
* This function updates the p2m and m2p tables with an identity map from
* start_pfn to start_pfn+size and prepares remapping the underlying RAM of the
* original allocation at remap_pfn. The information needed for remapping is
* saved in the memory itself to avoid the need for allocating buffers. The
* complete remap information is contained in a list of MFNs each containing
* up to REMAP_SIZE MFNs and the start target PFN for doing the remap.
* This enables us to preserve the original mfn sequence while doing the
* remapping at a time when the memory management is capable of allocating
* virtual and physical memory in arbitrary amounts, see 'xen_remap_memory' and
* its callers.
*/
static void __init xen_do_set_identity_and_remap_chunk(
unsigned long start_pfn, unsigned long size, unsigned long remap_pfn)
{
unsigned long buf = (unsigned long)&xen_remap_buf;
unsigned long mfn_save, mfn;
unsigned long ident_pfn_iter, remap_pfn_iter;
unsigned long ident_end_pfn = start_pfn + size;
unsigned long left = size;
unsigned int i, chunk;
WARN_ON(size == 0);
BUG_ON(xen_feature(XENFEAT_auto_translated_physmap));
mfn_save = virt_to_mfn(buf);
for (ident_pfn_iter = start_pfn, remap_pfn_iter = remap_pfn;
ident_pfn_iter < ident_end_pfn;
ident_pfn_iter += REMAP_SIZE, remap_pfn_iter += REMAP_SIZE) {
chunk = (left < REMAP_SIZE) ? left : REMAP_SIZE;
/* Map first pfn to xen_remap_buf */
mfn = pfn_to_mfn(ident_pfn_iter);
set_pte_mfn(buf, mfn, PAGE_KERNEL);
/* Save mapping information in page */
xen_remap_buf.next_area_mfn = xen_remap_mfn;
xen_remap_buf.target_pfn = remap_pfn_iter;
xen_remap_buf.size = chunk;
for (i = 0; i < chunk; i++)
xen_remap_buf.mfns[i] = pfn_to_mfn(ident_pfn_iter + i);
/* Put remap buf into list. */
xen_remap_mfn = mfn;
/* Set identity map */
set_phys_range_identity(ident_pfn_iter, ident_pfn_iter + chunk);
left -= chunk;
}
/* Restore old xen_remap_buf mapping */
set_pte_mfn(buf, mfn_save, PAGE_KERNEL);
}
/*
* This function takes a contiguous pfn range that needs to be identity mapped
* and:
*
* 1) Finds a new range of pfns to use to remap based on E820 and remap_pfn.
* 2) Calls the do_ function to actually do the mapping/remapping work.
*
* The goal is to not allocate additional memory but to remap the existing
* pages. In the case of an error the underlying memory is simply released back
* to Xen and not remapped.
*/
static unsigned long __init xen_set_identity_and_remap_chunk(
const struct e820entry *list, size_t map_size, unsigned long start_pfn,
unsigned long end_pfn, unsigned long nr_pages, unsigned long remap_pfn,
unsigned long *released)
{
unsigned long pfn;
unsigned long i = 0;
unsigned long n = end_pfn - start_pfn;
while (i < n) {
unsigned long cur_pfn = start_pfn + i;
unsigned long left = n - i;
unsigned long size = left;
unsigned long remap_range_size;
/* Do not remap pages beyond the current allocation */
if (cur_pfn >= nr_pages) {
/* Identity map remaining pages */
set_phys_range_identity(cur_pfn, cur_pfn + size);
break;
}
if (cur_pfn + size > nr_pages)
size = nr_pages - cur_pfn;
remap_range_size = xen_find_pfn_range(list, map_size,
&remap_pfn);
if (!remap_range_size) {
pr_warning("Unable to find available pfn range, not remapping identity pages\n");
xen_set_identity_and_release_chunk(cur_pfn,
cur_pfn + left, nr_pages, released);
break;
}
/* Adjust size to fit in current e820 RAM region */
if (size > remap_range_size)
size = remap_range_size;
xen_do_set_identity_and_remap_chunk(cur_pfn, size, remap_pfn);
/* Update variables to reflect new mappings. */
i += size;
remap_pfn += size;
}
/*
* If the PFNs are currently mapped, the VA mapping also needs
* to be updated to be 1:1.
*/
for (pfn = start_pfn; pfn <= max_pfn_mapped && pfn < end_pfn; pfn++)
(void)HYPERVISOR_update_va_mapping(
(unsigned long)__va(pfn << PAGE_SHIFT),
mfn_pte(pfn, PAGE_KERNEL_IO), 0);
return remap_pfn;
}
static void __init xen_set_identity_and_remap(
const struct e820entry *list, size_t map_size, unsigned long nr_pages,
unsigned long *released)
{
phys_addr_t start = 0;
unsigned long last_pfn = nr_pages;
const struct e820entry *entry;
unsigned long num_released = 0;
int i;
/*
* Combine non-RAM regions and gaps until a RAM region (or the
* end of the map) is reached, then set the 1:1 map and
* remap the memory in those non-RAM regions.
*
* The combined non-RAM regions are rounded to a whole number
* of pages so any partial pages are accessible via the 1:1
* mapping. This is needed for some BIOSes that put (for
* example) the DMI tables in a reserved region that begins on
* a non-page boundary.
*/
for (i = 0, entry = list; i < map_size; i++, entry++) {
phys_addr_t end = entry->addr + entry->size;
if (entry->type == E820_RAM || i == map_size - 1) {
unsigned long start_pfn = PFN_DOWN(start);
unsigned long end_pfn = PFN_UP(end);
if (entry->type == E820_RAM)
end_pfn = PFN_UP(entry->addr);
if (start_pfn < end_pfn)
last_pfn = xen_set_identity_and_remap_chunk(
list, map_size, start_pfn,
end_pfn, nr_pages, last_pfn,
&num_released);
start = end;
}
}
*released = num_released;
pr_info("Released %ld page(s)\n", num_released);
}
/*
* Remap the memory prepared in xen_do_set_identity_and_remap_chunk().
* The remap information (which mfn remap to which pfn) is contained in the
* to be remapped memory itself in a linked list anchored at xen_remap_mfn.
* This scheme allows to remap the different chunks in arbitrary order while
* the resulting mapping will be independant from the order.
*/
void __init xen_remap_memory(void)
{
unsigned long buf = (unsigned long)&xen_remap_buf;
unsigned long mfn_save, mfn, pfn;
unsigned long remapped = 0;
unsigned int i;
unsigned long pfn_s = ~0UL;
unsigned long len = 0;
mfn_save = virt_to_mfn(buf);
while (xen_remap_mfn != INVALID_P2M_ENTRY) {
/* Map the remap information */
set_pte_mfn(buf, xen_remap_mfn, PAGE_KERNEL);
BUG_ON(xen_remap_mfn != xen_remap_buf.mfns[0]);
pfn = xen_remap_buf.target_pfn;
for (i = 0; i < xen_remap_buf.size; i++) {
mfn = xen_remap_buf.mfns[i];
xen_update_mem_tables(pfn, mfn);
remapped++;
pfn++;
}
if (pfn_s == ~0UL || pfn == pfn_s) {
pfn_s = xen_remap_buf.target_pfn;
len += xen_remap_buf.size;
} else if (pfn_s + len == xen_remap_buf.target_pfn) {
len += xen_remap_buf.size;
} else {
xen_del_extra_mem(PFN_PHYS(pfn_s), PFN_PHYS(len));
pfn_s = xen_remap_buf.target_pfn;
len = xen_remap_buf.size;
}
mfn = xen_remap_mfn;
xen_remap_mfn = xen_remap_buf.next_area_mfn;
}
if (pfn_s != ~0UL && len)
xen_del_extra_mem(PFN_PHYS(pfn_s), PFN_PHYS(len));
set_pte_mfn(buf, mfn_save, PAGE_KERNEL);
pr_info("Remapped %ld page(s)\n", remapped);
}
static unsigned long __init xen_get_max_pages(void)
{
unsigned long max_pages = MAX_DOMAIN_PAGES;
domid_t domid = DOMID_SELF;
int ret;
xen: only limit memory map to maximum reservation for domain 0. d312ae878b6a "xen: use maximum reservation to limit amount of usable RAM" clamped the total amount of RAM to the current maximum reservation. This is correct for dom0 but is not correct for guest domains. In order to boot a guest "pre-ballooned" (e.g. with memory=1G but maxmem=2G) in order to allow for future memory expansion the guest must derive max_pfn from the e820 provided by the toolstack and not the current maximum reservation (which can reflect only the current maximum, not the guest lifetime max). The existing algorithm already behaves this correctly if we do not artificially limit the maximum number of pages for the guest case. For a guest booted with maxmem=512, memory=128 this results in: [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 00000000000a0000 (usable) [ 0.000000] Xen: 00000000000a0000 - 0000000000100000 (reserved) -[ 0.000000] Xen: 0000000000100000 - 0000000008100000 (usable) -[ 0.000000] Xen: 0000000008100000 - 0000000020800000 (unusable) +[ 0.000000] Xen: 0000000000100000 - 0000000020800000 (usable) ... [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI not present or invalid. [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) -[ 0.000000] last_pfn = 0x8100 max_arch_pfn = 0x1000000 +[ 0.000000] last_pfn = 0x20800 max_arch_pfn = 0x1000000 [ 0.000000] initial memory mapped : 0 - 027ff000 [ 0.000000] Base memory trampoline at [c009f000] 9f000 size 4096 -[ 0.000000] init_memory_mapping: 0000000000000000-0000000008100000 -[ 0.000000] 0000000000 - 0008100000 page 4k -[ 0.000000] kernel direct mapping tables up to 8100000 @ 27bb000-27ff000 +[ 0.000000] init_memory_mapping: 0000000000000000-0000000020800000 +[ 0.000000] 0000000000 - 0020800000 page 4k +[ 0.000000] kernel direct mapping tables up to 20800000 @ 26f8000-27ff000 [ 0.000000] xen: setting RW the range 27e8000 - 27ff000 [ 0.000000] 0MB HIGHMEM available. -[ 0.000000] 129MB LOWMEM available. -[ 0.000000] mapped low ram: 0 - 08100000 -[ 0.000000] low ram: 0 - 08100000 +[ 0.000000] 520MB LOWMEM available. +[ 0.000000] mapped low ram: 0 - 20800000 +[ 0.000000] low ram: 0 - 20800000 With this change "xl mem-set <domain> 512M" will successfully increase the guest RAM (by reducing the balloon). There is no change for dom0. Reported-and-Tested-by: George Shuklin <george.shuklin@gmail.com> Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: stable@kernel.org Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2011-12-14 20:16:08 +08:00
/*
* For the initial domain we use the maximum reservation as
* the maximum page.
*
* For guest domains the current maximum reservation reflects
* the current maximum rather than the static maximum. In this
* case the e820 map provided to us will cover the static
* maximum region.
*/
if (xen_initial_domain()) {
ret = HYPERVISOR_memory_op(XENMEM_maximum_reservation, &domid);
if (ret > 0)
max_pages = ret;
}
return min(max_pages, MAX_DOMAIN_PAGES);
}
static void xen_align_and_add_e820_region(u64 start, u64 size, int type)
{
u64 end = start + size;
/* Align RAM regions to page boundaries. */
if (type == E820_RAM) {
start = PAGE_ALIGN(start);
end &= ~((u64)PAGE_SIZE - 1);
}
e820_add_region(start, end - start, type);
}
x86/xen: do not identity map UNUSABLE regions in the machine E820 If there are UNUSABLE regions in the machine memory map, dom0 will attempt to map them 1:1 which is not permitted by Xen and the kernel will crash. There isn't anything interesting in the UNUSABLE region that the dom0 kernel needs access to so we can avoid making the 1:1 mapping and treat it as RAM. We only do this for dom0, as that is where tboot case shows up. A PV domU could have an UNUSABLE region in its pseudo-physical map and would need to be handled in another patch. This fixes a boot failure on hosts with tboot. tboot marks a region in the e820 map as unusable and the dom0 kernel would attempt to map this region and Xen does not permit unusable regions to be mapped by guests. (XEN) 0000000000000000 - 0000000000060000 (usable) (XEN) 0000000000060000 - 0000000000068000 (reserved) (XEN) 0000000000068000 - 000000000009e000 (usable) (XEN) 0000000000100000 - 0000000000800000 (usable) (XEN) 0000000000800000 - 0000000000972000 (unusable) tboot marked this region as unusable. (XEN) 0000000000972000 - 00000000cf200000 (usable) (XEN) 00000000cf200000 - 00000000cf38f000 (reserved) (XEN) 00000000cf38f000 - 00000000cf3ce000 (ACPI data) (XEN) 00000000cf3ce000 - 00000000d0000000 (reserved) (XEN) 00000000e0000000 - 00000000f0000000 (reserved) (XEN) 00000000fe000000 - 0000000100000000 (reserved) (XEN) 0000000100000000 - 0000000630000000 (usable) Signed-off-by: David Vrabel <david.vrabel@citrix.com> [v1: Altered the patch and description with domU's with UNUSABLE regions] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2013-08-16 22:42:55 +08:00
void xen_ignore_unusable(struct e820entry *list, size_t map_size)
{
struct e820entry *entry;
unsigned int i;
for (i = 0, entry = list; i < map_size; i++, entry++) {
if (entry->type == E820_UNUSABLE)
entry->type = E820_RAM;
}
}
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
/**
* machine_specific_memory_setup - Hook for machine specific memory setup.
**/
char * __init xen_memory_setup(void)
{
static struct e820entry map[E820MAX] __initdata;
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
unsigned long max_pfn = xen_start_info->nr_pages;
unsigned long long mem_end;
int rc;
struct xen_memory_map memmap;
unsigned long max_pages;
unsigned long extra_pages = 0;
int i;
int op;
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
max_pfn = min(MAX_DOMAIN_PAGES, max_pfn);
mem_end = PFN_PHYS(max_pfn);
memmap.nr_entries = E820MAX;
set_xen_guest_handle(memmap.buffer, map);
op = xen_initial_domain() ?
XENMEM_machine_memory_map :
XENMEM_memory_map;
rc = HYPERVISOR_memory_op(op, &memmap);
if (rc == -ENOSYS) {
BUG_ON(xen_initial_domain());
memmap.nr_entries = 1;
map[0].addr = 0ULL;
map[0].size = mem_end;
/* 8MB slack (to balance backend allocations). */
map[0].size += 8ULL << 20;
map[0].type = E820_RAM;
rc = 0;
}
BUG_ON(rc);
BUG_ON(memmap.nr_entries == 0);
x86/xen: do not identity map UNUSABLE regions in the machine E820 If there are UNUSABLE regions in the machine memory map, dom0 will attempt to map them 1:1 which is not permitted by Xen and the kernel will crash. There isn't anything interesting in the UNUSABLE region that the dom0 kernel needs access to so we can avoid making the 1:1 mapping and treat it as RAM. We only do this for dom0, as that is where tboot case shows up. A PV domU could have an UNUSABLE region in its pseudo-physical map and would need to be handled in another patch. This fixes a boot failure on hosts with tboot. tboot marks a region in the e820 map as unusable and the dom0 kernel would attempt to map this region and Xen does not permit unusable regions to be mapped by guests. (XEN) 0000000000000000 - 0000000000060000 (usable) (XEN) 0000000000060000 - 0000000000068000 (reserved) (XEN) 0000000000068000 - 000000000009e000 (usable) (XEN) 0000000000100000 - 0000000000800000 (usable) (XEN) 0000000000800000 - 0000000000972000 (unusable) tboot marked this region as unusable. (XEN) 0000000000972000 - 00000000cf200000 (usable) (XEN) 00000000cf200000 - 00000000cf38f000 (reserved) (XEN) 00000000cf38f000 - 00000000cf3ce000 (ACPI data) (XEN) 00000000cf3ce000 - 00000000d0000000 (reserved) (XEN) 00000000e0000000 - 00000000f0000000 (reserved) (XEN) 00000000fe000000 - 0000000100000000 (reserved) (XEN) 0000000100000000 - 0000000630000000 (usable) Signed-off-by: David Vrabel <david.vrabel@citrix.com> [v1: Altered the patch and description with domU's with UNUSABLE regions] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2013-08-16 22:42:55 +08:00
/*
* Xen won't allow a 1:1 mapping to be created to UNUSABLE
* regions, so if we're using the machine memory map leave the
* region as RAM as it is in the pseudo-physical map.
*
* UNUSABLE regions in domUs are not handled and will need
* a patch in the future.
*/
if (xen_initial_domain())
xen_ignore_unusable(map, memmap.nr_entries);
/* Make sure the Xen-supplied memory map is well-ordered. */
sanitize_e820_map(map, memmap.nr_entries, &memmap.nr_entries);
max_pages = xen_get_max_pages();
if (max_pages > max_pfn)
extra_pages += max_pages - max_pfn;
/*
* Set identity map on non-RAM pages and prepare remapping the
* underlying RAM.
*/
xen_set_identity_and_remap(map, memmap.nr_entries, max_pfn,
&xen_released_pages);
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
extra_pages += xen_released_pages;
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM When the Xen hypervisor boots a PV kernel it hands it two pieces of information: nr_pages and a made up E820 entry. The nr_pages value defines the range from zero to nr_pages of PFNs which have a valid Machine Frame Number (MFN) underneath it. The E820 mirrors that (with the VGA hole): BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000000a0000 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000080800000 (usable) The fun comes when a PV guest that is run with a machine E820 - that can either be the initial domain or a PCI PV guest, where the E820 looks like the normal thing: BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009e000 (usable) Xen: 000000000009ec00 - 0000000000100000 (reserved) Xen: 0000000000100000 - 0000000020000000 (usable) Xen: 0000000020000000 - 0000000020200000 (reserved) Xen: 0000000020200000 - 0000000040000000 (usable) Xen: 0000000040000000 - 0000000040200000 (reserved) Xen: 0000000040200000 - 00000000bad80000 (usable) Xen: 00000000bad80000 - 00000000badc9000 (ACPI NVS) .. With that overlaying the nr_pages directly on the E820 does not work as there are gaps and non-RAM regions that won't be used by the memory allocator. The 'xen_release_chunk' helps with that by punching holes in the P2M (PFN to MFN lookup tree) for those regions and tells us that: Freeing 20000-20200 pfn range: 512 pages freed Freeing 40000-40200 pfn range: 512 pages freed Freeing bad80-badf4 pfn range: 116 pages freed Freeing badf6-bae7f pfn range: 137 pages freed Freeing bb000-100000 pfn range: 282624 pages freed Released 283999 pages of unused memory Those 283999 pages are subtracted from the nr_pages and are returned to the hypervisor. The end result is that the initial domain boots with 1GB less memory as the nr_pages has been subtracted by the amount of pages residing within the PCI hole. It can balloon up to that if desired using 'xl mem-set 0 8092', but the balloon driver is not always compiled in for the initial domain. This patch, implements the populate hypercall (XENMEM_populate_physmap) which increases the the domain with the same amount of pages that were released. The other solution (that did not work) was to transplant the MFN in the P2M tree - the ones that were going to be freed were put in the E820_RAM regions past the nr_pages. But the modifications to the M2P array (the other side of creating PTEs) were not carried away. As the hypervisor is the only one capable of modifying that and the only two hypercalls that would do this are: the update_va_mapping (which won't work, as during initial bootup only PFNs up to nr_pages are mapped in the guest) or via the populate hypercall. The end result is that the kernel can now boot with the nr_pages without having to subtract the 283999 pages. On a 8GB machine, with various dom0_mem= parameters this is what we get: no dom0_mem -Memory: 6485264k/9435136k available (5817k kernel code, 1136060k absent, 1813812k reserved, 2899k data, 696k init) +Memory: 7619036k/9435136k available (5817k kernel code, 1136060k absent, 680040k reserved, 2899k data, 696k init) dom0_mem=3G -Memory: 2616536k/9435136k available (5817k kernel code, 1136060k absent, 5682540k reserved, 2899k data, 696k init) +Memory: 2703776k/9435136k available (5817k kernel code, 1136060k absent, 5595300k reserved, 2899k data, 696k init) dom0_mem=max:3G -Memory: 2696732k/4281724k available (5817k kernel code, 1136060k absent, 448932k reserved, 2899k data, 696k init) +Memory: 2702204k/4281724k available (5817k kernel code, 1136060k absent, 443460k reserved, 2899k data, 696k init) And the 'xm list' or 'xl list' now reflect what the dom0_mem= argument is. Acked-by: David Vrabel <david.vrabel@citrix.com> [v2: Use populate hypercall] [v3: Remove debug printks] [v4: Simplify code] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-04-06 22:07:11 +08:00
/*
* Clamp the amount of extra memory to a EXTRA_MEM_RATIO
* factor the base size. On non-highmem systems, the base
* size is the full initial memory allocation; on highmem it
* is limited to the max size of lowmem, so that it doesn't
* get completely filled.
*
* In principle there could be a problem in lowmem systems if
* the initial memory is also very large with respect to
* lowmem, but we won't try to deal with that here.
*/
extra_pages = min(EXTRA_MEM_RATIO * min(max_pfn, PFN_DOWN(MAXMEM)),
extra_pages);
i = 0;
while (i < memmap.nr_entries) {
u64 addr = map[i].addr;
u64 size = map[i].size;
u32 type = map[i].type;
if (type == E820_RAM) {
if (addr < mem_end) {
size = min(size, mem_end - addr);
} else if (extra_pages) {
size = min(size, (u64)extra_pages * PAGE_SIZE);
extra_pages -= size / PAGE_SIZE;
xen_add_extra_mem(addr, size);
xen_max_p2m_pfn = PFN_DOWN(addr + size);
} else
type = E820_UNUSABLE;
}
xen_align_and_add_e820_region(addr, size, type);
map[i].addr += size;
map[i].size -= size;
if (map[i].size == 0)
i++;
}
/*
* Set the rest as identity mapped, in case PCI BARs are
* located here.
*
* PFNs above MAX_P2M_PFN are considered identity mapped as
* well.
*/
set_phys_range_identity(map[i-1].addr / PAGE_SIZE, ~0ul);
/*
* In domU, the ISA region is normal, usable memory, but we
* reserve ISA memory anyway because too many things poke
* about in there.
*/
e820_add_region(ISA_START_ADDRESS, ISA_END_ADDRESS - ISA_START_ADDRESS,
E820_RESERVED);
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
/*
* Reserve Xen bits:
* - mfn_list
* - xen_start_info
* See comment above "struct start_info" in <xen/interface/xen.h>
* We tried to make the the memblock_reserve more selective so
* that it would be clear what region is reserved. Sadly we ran
* in the problem wherein on a 64-bit hypervisor with a 32-bit
* initial domain, the pt_base has the cr3 value which is not
* neccessarily where the pagetable starts! As Jan put it: "
* Actually, the adjustment turns out to be correct: The page
* tables for a 32-on-64 dom0 get allocated in the order "first L1",
* "first L2", "first L3", so the offset to the page table base is
* indeed 2. When reading xen/include/public/xen.h's comment
* very strictly, this is not a violation (since there nothing is said
* that the first thing in the page table space is pointed to by
* pt_base; I admit that this seems to be implied though, namely
* do I think that it is implied that the page table space is the
* range [pt_base, pt_base + nt_pt_frames), whereas that
* range here indeed is [pt_base - 2, pt_base - 2 + nt_pt_frames),
* which - without a priori knowledge - the kernel would have
* difficulty to figure out)." - so lets just fall back to the
* easy way and reserve the whole region.
*/
memblock_reserve(__pa(xen_start_info->mfn_list),
xen_start_info->pt_base - xen_start_info->mfn_list);
sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
return "Xen";
}
/*
* Machine specific memory setup for auto-translated guests.
*/
char * __init xen_auto_xlated_memory_setup(void)
{
static struct e820entry map[E820MAX] __initdata;
struct xen_memory_map memmap;
int i;
int rc;
memmap.nr_entries = E820MAX;
set_xen_guest_handle(memmap.buffer, map);
rc = HYPERVISOR_memory_op(XENMEM_memory_map, &memmap);
if (rc < 0)
panic("No memory map (%d)\n", rc);
sanitize_e820_map(map, ARRAY_SIZE(map), &memmap.nr_entries);
for (i = 0; i < memmap.nr_entries; i++)
e820_add_region(map[i].addr, map[i].size, map[i].type);
memblock_reserve(__pa(xen_start_info->mfn_list),
xen_start_info->pt_base - xen_start_info->mfn_list);
return "Xen";
}
/*
* Set the bit indicating "nosegneg" library variants should be used.
* We only need to bother in pure 32-bit mode; compat 32-bit processes
* can have un-truncated segments, so wrapping around is allowed.
*/
static void __init fiddle_vdso(void)
{
#ifdef CONFIG_X86_32
x86, vdso: Reimplement vdso.so preparation in build-time C Currently, vdso.so files are prepared and analyzed by a combination of objcopy, nm, some linker script tricks, and some simple ELF parsers in the kernel. Replace all of that with plain C code that runs at build time. All five vdso images now generate .c files that are compiled and linked in to the kernel image. This should cause only one userspace-visible change: the loaded vDSO images are stripped more heavily than they used to be. Everything outside the loadable segment is dropped. In particular, this causes the section table and section name strings to be missing. This should be fine: real dynamic loaders don't load or inspect these tables anyway. The result is roughly equivalent to eu-strip's --strip-sections option. The purpose of this change is to enable the vvar and hpet mappings to be moved to the page following the vDSO load segment. Currently, it is possible for the section table to extend into the page after the load segment, so, if we map it, it risks overlapping the vvar or hpet page. This happens whenever the load segment is just under a multiple of PAGE_SIZE. The only real subtlety here is that the old code had a C file with inline assembler that did 'call VDSO32_vsyscall' and a linker script that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most likely worked by accident: the linker script entry defines a symbol associated with an address as opposed to an alias for the real dynamic symbol __kernel_vsyscall. That caused ld to relocate the reference at link time instead of leaving an interposable dynamic relocation. Since the VDSO32_vsyscall hack is no longer needed, I now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it work. vdso2c will generate an error and abort the build if the resulting image contains any dynamic relocations, so we won't silently generate bad vdso images. (Dynamic relocations are a problem because nothing will even attempt to relocate the vdso.) Signed-off-by: Andy Lutomirski <luto@amacapital.net> Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-06 03:19:34 +08:00
/*
* This could be called before selected_vdso32 is initialized, so
* just fiddle with both possible images. vdso_image_32_syscall
* can't be selected, since it only exists on 64-bit systems.
*/
u32 *mask;
x86, vdso: Reimplement vdso.so preparation in build-time C Currently, vdso.so files are prepared and analyzed by a combination of objcopy, nm, some linker script tricks, and some simple ELF parsers in the kernel. Replace all of that with plain C code that runs at build time. All five vdso images now generate .c files that are compiled and linked in to the kernel image. This should cause only one userspace-visible change: the loaded vDSO images are stripped more heavily than they used to be. Everything outside the loadable segment is dropped. In particular, this causes the section table and section name strings to be missing. This should be fine: real dynamic loaders don't load or inspect these tables anyway. The result is roughly equivalent to eu-strip's --strip-sections option. The purpose of this change is to enable the vvar and hpet mappings to be moved to the page following the vDSO load segment. Currently, it is possible for the section table to extend into the page after the load segment, so, if we map it, it risks overlapping the vvar or hpet page. This happens whenever the load segment is just under a multiple of PAGE_SIZE. The only real subtlety here is that the old code had a C file with inline assembler that did 'call VDSO32_vsyscall' and a linker script that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most likely worked by accident: the linker script entry defines a symbol associated with an address as opposed to an alias for the real dynamic symbol __kernel_vsyscall. That caused ld to relocate the reference at link time instead of leaving an interposable dynamic relocation. Since the VDSO32_vsyscall hack is no longer needed, I now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it work. vdso2c will generate an error and abort the build if the resulting image contains any dynamic relocations, so we won't silently generate bad vdso images. (Dynamic relocations are a problem because nothing will even attempt to relocate the vdso.) Signed-off-by: Andy Lutomirski <luto@amacapital.net> Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-06 03:19:34 +08:00
mask = vdso_image_32_int80.data +
vdso_image_32_int80.sym_VDSO32_NOTE_MASK;
*mask |= 1 << VDSO_NOTE_NONEGSEG_BIT;
x86, vdso: Reimplement vdso.so preparation in build-time C Currently, vdso.so files are prepared and analyzed by a combination of objcopy, nm, some linker script tricks, and some simple ELF parsers in the kernel. Replace all of that with plain C code that runs at build time. All five vdso images now generate .c files that are compiled and linked in to the kernel image. This should cause only one userspace-visible change: the loaded vDSO images are stripped more heavily than they used to be. Everything outside the loadable segment is dropped. In particular, this causes the section table and section name strings to be missing. This should be fine: real dynamic loaders don't load or inspect these tables anyway. The result is roughly equivalent to eu-strip's --strip-sections option. The purpose of this change is to enable the vvar and hpet mappings to be moved to the page following the vDSO load segment. Currently, it is possible for the section table to extend into the page after the load segment, so, if we map it, it risks overlapping the vvar or hpet page. This happens whenever the load segment is just under a multiple of PAGE_SIZE. The only real subtlety here is that the old code had a C file with inline assembler that did 'call VDSO32_vsyscall' and a linker script that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most likely worked by accident: the linker script entry defines a symbol associated with an address as opposed to an alias for the real dynamic symbol __kernel_vsyscall. That caused ld to relocate the reference at link time instead of leaving an interposable dynamic relocation. Since the VDSO32_vsyscall hack is no longer needed, I now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it work. vdso2c will generate an error and abort the build if the resulting image contains any dynamic relocations, so we won't silently generate bad vdso images. (Dynamic relocations are a problem because nothing will even attempt to relocate the vdso.) Signed-off-by: Andy Lutomirski <luto@amacapital.net> Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-06 03:19:34 +08:00
mask = vdso_image_32_sysenter.data +
vdso_image_32_sysenter.sym_VDSO32_NOTE_MASK;
*mask |= 1 << VDSO_NOTE_NONEGSEG_BIT;
#endif
}
x86: delete __cpuinit usage from all x86 files The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) are flagged as __cpuinit -- so if we remove the __cpuinit from arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. This removes all the arch/x86 uses of the __cpuinit macros from all C files. x86 only had the one __CPUINIT used in assembly files, and it wasn't paired off with a .previous or a __FINIT, so we can delete it directly w/o any corresponding additional change there. [1] https://lkml.org/lkml/2013/5/20/589 Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2013-06-19 06:23:59 +08:00
static int register_callback(unsigned type, const void *func)
{
struct callback_register callback = {
.type = type,
.address = XEN_CALLBACK(__KERNEL_CS, func),
.flags = CALLBACKF_mask_events,
};
return HYPERVISOR_callback_op(CALLBACKOP_register, &callback);
}
x86: delete __cpuinit usage from all x86 files The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) are flagged as __cpuinit -- so if we remove the __cpuinit from arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. This removes all the arch/x86 uses of the __cpuinit macros from all C files. x86 only had the one __CPUINIT used in assembly files, and it wasn't paired off with a .previous or a __FINIT, so we can delete it directly w/o any corresponding additional change there. [1] https://lkml.org/lkml/2013/5/20/589 Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2013-06-19 06:23:59 +08:00
void xen_enable_sysenter(void)
{
int ret;
unsigned sysenter_feature;
#ifdef CONFIG_X86_32
sysenter_feature = X86_FEATURE_SEP;
#else
sysenter_feature = X86_FEATURE_SYSENTER32;
#endif
if (!boot_cpu_has(sysenter_feature))
return;
ret = register_callback(CALLBACKTYPE_sysenter, xen_sysenter_target);
if(ret != 0)
setup_clear_cpu_cap(sysenter_feature);
}
x86: delete __cpuinit usage from all x86 files The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. Note that some harmless section mismatch warnings may result, since notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c) are flagged as __cpuinit -- so if we remove the __cpuinit from arch specific callers, we will also get section mismatch warnings. As an intermediate step, we intend to turn the linux/init.h cpuinit content into no-ops as early as possible, since that will get rid of these warnings. In any case, they are temporary and harmless. This removes all the arch/x86 uses of the __cpuinit macros from all C files. x86 only had the one __CPUINIT used in assembly files, and it wasn't paired off with a .previous or a __FINIT, so we can delete it directly w/o any corresponding additional change there. [1] https://lkml.org/lkml/2013/5/20/589 Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2013-06-19 06:23:59 +08:00
void xen_enable_syscall(void)
{
#ifdef CONFIG_X86_64
int ret;
ret = register_callback(CALLBACKTYPE_syscall, xen_syscall_target);
if (ret != 0) {
printk(KERN_ERR "Failed to set syscall callback: %d\n", ret);
/* Pretty fatal; 64-bit userspace has no other
mechanism for syscalls. */
}
if (boot_cpu_has(X86_FEATURE_SYSCALL32)) {
ret = register_callback(CALLBACKTYPE_syscall32,
xen_syscall32_target);
if (ret != 0)
setup_clear_cpu_cap(X86_FEATURE_SYSCALL32);
}
#endif /* CONFIG_X86_64 */
}
void __init xen_pvmmu_arch_setup(void)
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
{
HYPERVISOR_vm_assist(VMASST_CMD_enable, VMASST_TYPE_4gb_segments);
HYPERVISOR_vm_assist(VMASST_CMD_enable, VMASST_TYPE_writable_pagetables);
HYPERVISOR_vm_assist(VMASST_CMD_enable,
VMASST_TYPE_pae_extended_cr3);
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
if (register_callback(CALLBACKTYPE_event, xen_hypervisor_callback) ||
register_callback(CALLBACKTYPE_failsafe, xen_failsafe_callback))
BUG();
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
xen_enable_sysenter();
xen_enable_syscall();
}
/* This function is not called for HVM domains */
void __init xen_arch_setup(void)
{
xen_panic_handler_init();
if (!xen_feature(XENFEAT_auto_translated_physmap))
xen_pvmmu_arch_setup();
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
#ifdef CONFIG_ACPI
if (!(xen_start_info->flags & SIF_INITDOMAIN)) {
printk(KERN_INFO "ACPI in unprivileged domain disabled\n");
disable_acpi();
}
#endif
memcpy(boot_command_line, xen_start_info->cmd_line,
MAX_GUEST_CMDLINE > COMMAND_LINE_SIZE ?
COMMAND_LINE_SIZE : MAX_GUEST_CMDLINE);
/* Set up idle, making sure it calls safe_halt() pvop */
disable_cpuidle();
disable_cpufreq();
WARN_ON(xen_set_default_idle());
fiddle_vdso();
xen/boot: Disable NUMA for PV guests. The hypervisor is in charge of allocating the proper "NUMA" memory and dealing with the CPU scheduler to keep them bound to the proper NUMA node. The PV guests (and PVHVM) have no inkling of where they run and do not need to know that right now. In the future we will need to inject NUMA configuration data (if a guest spans two or more NUMA nodes) so that the kernel can make the right choices. But those patches are not yet present. In the meantime, disable the NUMA capability in the PV guest, which also fixes a bootup issue. Andre says: "we see Dom0 crashes due to the kernel detecting the NUMA topology not by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA). This will detect the actual NUMA config of the physical machine, but will crash about the mismatch with Dom0's virtual memory. Variation of the theme: Dom0 sees what it's not supposed to see. This happens with the said config option enabled and on a machine where this scanning is still enabled (K8 and Fam10h, not Bulldozer class) We have this dump then: NUMA: Warning: node ids are out of bound, from=-1 to=-1 distance=10 Scanning NUMA topology in Northbridge 24 Number of physical nodes 4 Node 0 MemBase 0000000000000000 Limit 0000000040000000 Node 1 MemBase 0000000040000000 Limit 0000000138000000 Node 2 MemBase 0000000138000000 Limit 00000001f8000000 Node 3 MemBase 00000001f8000000 Limit 0000000238000000 Initmem setup node 0 0000000000000000-0000000040000000 NODE_DATA [000000003ffd9000 - 000000003fffffff] Initmem setup node 1 0000000040000000-0000000138000000 NODE_DATA [0000000137fd9000 - 0000000137ffffff] Initmem setup node 2 0000000138000000-00000001f8000000 NODE_DATA [00000001f095e000 - 00000001f0984fff] Initmem setup node 3 00000001f8000000-0000000238000000 Cannot find 159744 bytes in node 3 BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96 Pid: 0, comm: swapper Not tainted 3.3.6 #1 AMD Dinar/Dinar RIP: e030:[<ffffffff81d220e6>] [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96 .. snip.. [<ffffffff81d23024>] sparse_early_usemaps_alloc_node+0x64/0x178 [<ffffffff81d23348>] sparse_init+0xe4/0x25a [<ffffffff81d16840>] paging_init+0x13/0x22 [<ffffffff81d07fbb>] setup_arch+0x9c6/0xa9b [<ffffffff81683954>] ? printk+0x3c/0x3e [<ffffffff81d01a38>] start_kernel+0xe5/0x468 [<ffffffff81d012cf>] x86_64_start_reservations+0xba/0xc1 [<ffffffff81007153>] ? xen_setup_runstate_info+0x2c/0x36 [<ffffffff81d050ee>] xen_start_kernel+0x565/0x56c " so we just disable NUMA scanning by setting numa_off=1. CC: stable@vger.kernel.org Reported-and-Tested-by: Andre Przywara <andre.przywara@amd.com> Acked-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-08-17 22:22:37 +08:00
#ifdef CONFIG_NUMA
numa_off = 1;
#endif
xen: Core Xen implementation This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 09:37:04 +08:00
}