UbiquitousOS
/
OpenCloudOS-Kernel
mirror of https://gitee.com/OpenCloudOS/OpenCloudOS-Kernel.git
11
0
Fork 0
Code Issues Projects Releases Wiki Activity
OpenCloudOS-Kernel/drivers/clk/clk-versaclock5.c

978 lines
26 KiB
C
Raw Normal View History

clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
/*
* Driver for IDT Versaclock 5
*
* Copyright (C) 2017 Marek Vasut <marek.vasut@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
/*
* Possible optimizations:
* - Use spread spectrum
* - Use integer divider in FOD if applicable
*/
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/rational.h>
#include <linux/regmap.h>
#include <linux/slab.h>
/* VersaClock5 registers */
#define VC5_OTP_CONTROL 0x00
/* Factory-reserved register block */
#define VC5_RSVD_DEVICE_ID 0x01
#define VC5_RSVD_ADC_GAIN_7_0 0x02
#define VC5_RSVD_ADC_GAIN_15_8 0x03
#define VC5_RSVD_ADC_OFFSET_7_0 0x04
#define VC5_RSVD_ADC_OFFSET_15_8 0x05
#define VC5_RSVD_TEMPY 0x06
#define VC5_RSVD_OFFSET_TBIN 0x07
#define VC5_RSVD_GAIN 0x08
#define VC5_RSVD_TEST_NP 0x09
#define VC5_RSVD_UNUSED 0x0a
#define VC5_RSVD_BANDGAP_TRIM_UP 0x0b
#define VC5_RSVD_BANDGAP_TRIM_DN 0x0c
#define VC5_RSVD_CLK_R_12_CLK_AMP_4 0x0d
#define VC5_RSVD_CLK_R_34_CLK_AMP_4 0x0e
#define VC5_RSVD_CLK_AMP_123 0x0f
/* Configuration register block */
#define VC5_PRIM_SRC_SHDN 0x10
#define VC5_PRIM_SRC_SHDN_EN_XTAL BIT(7)
#define VC5_PRIM_SRC_SHDN_EN_CLKIN BIT(6)
clk: vc5: Add support for the input frequency doubler The VersaClock 6 has an input frequency doubler between the input clock mux and the predivider. Add new capability flag and support for this frequency doubler block into the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:12 +08:00
#define VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ BIT(3)
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
#define VC5_PRIM_SRC_SHDN_SP BIT(1)
#define VC5_PRIM_SRC_SHDN_EN_GBL_SHDN BIT(0)
#define VC5_VCO_BAND 0x11
#define VC5_XTAL_X1_LOAD_CAP 0x12
#define VC5_XTAL_X2_LOAD_CAP 0x13
#define VC5_REF_DIVIDER 0x15
#define VC5_REF_DIVIDER_SEL_PREDIV2 BIT(7)
#define VC5_REF_DIVIDER_REF_DIV(n) ((n) & 0x3f)
#define VC5_VCO_CTRL_AND_PREDIV 0x16
#define VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV BIT(7)
#define VC5_FEEDBACK_INT_DIV 0x17
#define VC5_FEEDBACK_INT_DIV_BITS 0x18
#define VC5_FEEDBACK_FRAC_DIV(n) (0x19 + (n))
#define VC5_RC_CONTROL0 0x1e
#define VC5_RC_CONTROL1 0x1f
/* Register 0x20 is factory reserved */
/* Output divider control for divider 1,2,3,4 */
#define VC5_OUT_DIV_CONTROL(idx) (0x21 + ((idx) * 0x10))
#define VC5_OUT_DIV_CONTROL_RESET BIT(7)
#define VC5_OUT_DIV_CONTROL_SELB_NORM BIT(3)
#define VC5_OUT_DIV_CONTROL_SEL_EXT BIT(2)
#define VC5_OUT_DIV_CONTROL_INT_MODE BIT(1)
#define VC5_OUT_DIV_CONTROL_EN_FOD BIT(0)
#define VC5_OUT_DIV_FRAC(idx, n) (0x22 + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_FRAC4_OD_SCEE BIT(1)
#define VC5_OUT_DIV_STEP_SPREAD(idx, n) (0x26 + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_SPREAD_MOD(idx, n) (0x29 + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_SKEW_INT(idx, n) (0x2b + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_INT(idx, n) (0x2d + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_SKEW_FRAC(idx) (0x2f + ((idx) * 0x10))
/* Registers 0x30, 0x40, 0x50 are factory reserved */
/* Clock control register for clock 1,2 */
#define VC5_CLK_OUTPUT_CFG(idx, n) (0x60 + ((idx) * 0x2) + (n))
#define VC5_CLK_OUTPUT_CFG1_EN_CLKBUF BIT(0)
#define VC5_CLK_OE_SHDN 0x68
#define VC5_CLK_OS_SHDN 0x69
#define VC5_GLOBAL_REGISTER 0x76
#define VC5_GLOBAL_REGISTER_GLOBAL_RESET BIT(5)
/* PLL/VCO runs between 2.5 GHz and 3.0 GHz */
#define VC5_PLL_VCO_MIN 2500000000UL
#define VC5_PLL_VCO_MAX 3000000000UL
/* VC5 Input mux settings */
#define VC5_MUX_IN_XIN BIT(0)
#define VC5_MUX_IN_CLKIN BIT(1)
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
/* Maximum number of clk_out supported by this driver */
clk: vc5: Add support for IDT VersaClock 5P49V5935 Update IDT VersaClock 5 driver to support 5P49V5935. This chip has two clock inputs (internal XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Current driver supports up to 2 FODs and up to 3 clock outputs. This patch sets max number of supported FODs to 4 and max number of supported clock outputs to 5. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:24 +08:00
#define VC5_MAX_CLK_OUT_NUM 5
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
/* Maximum number of FODs supported by this driver */
clk: vc5: Add support for IDT VersaClock 5P49V5935 Update IDT VersaClock 5 driver to support 5P49V5935. This chip has two clock inputs (internal XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Current driver supports up to 2 FODs and up to 3 clock outputs. This patch sets max number of supported FODs to 4 and max number of supported clock outputs to 5. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:24 +08:00
#define VC5_MAX_FOD_NUM 4
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
/* flags to describe chip features */
/* chip has built-in oscilator */
#define VC5_HAS_INTERNAL_XTAL BIT(0)
clk: vc5: Add support for the input frequency doubler The VersaClock 6 has an input frequency doubler between the input clock mux and the predivider. Add new capability flag and support for this frequency doubler block into the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:12 +08:00
/* chip has PFD requency doubler */
#define VC5_HAS_PFD_FREQ_DBL BIT(1)
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
/* Supported IDT VC5 models. */
enum vc5_model {
IDT_VC5_5P49V5923,
clk: vc5: Add support for IDT VersaClock 5P49V5925 Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only external clock input, four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-10 01:39:57 +08:00
IDT_VC5_5P49V5925,
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
IDT_VC5_5P49V5933,
clk: vc5: Add support for IDT VersaClock 5P49V5935 Update IDT VersaClock 5 driver to support 5P49V5935. This chip has two clock inputs (internal XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Current driver supports up to 2 FODs and up to 3 clock outputs. This patch sets max number of supported FODs to 4 and max number of supported clock outputs to 5. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:24 +08:00
IDT_VC5_5P49V5935,
clk: vc5: Add support for IDT VersaClock 5P49V6901 Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901. This chip has two clock inputs (external XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:14 +08:00
IDT_VC6_5P49V6901,
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
};
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
/* Structure to describe features of a particular VC5 model */
struct vc5_chip_info {
const enum vc5_model model;
const unsigned int clk_fod_cnt;
const unsigned int clk_out_cnt;
const u32 flags;
};
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
struct vc5_driver_data;
struct vc5_hw_data {
struct clk_hw hw;
struct vc5_driver_data *vc5;
u32 div_int;
u32 div_frc;
unsigned int num;
};
struct vc5_driver_data {
struct i2c_client *client;
struct regmap *regmap;
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
const struct vc5_chip_info *chip_info;
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
struct clk *pin_xin;
struct clk *pin_clkin;
unsigned char clk_mux_ins;
struct clk_hw clk_mux;
clk: vc5: Add support for the input frequency doubler The VersaClock 6 has an input frequency doubler between the input clock mux and the predivider. Add new capability flag and support for this frequency doubler block into the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:12 +08:00
struct clk_hw clk_mul;
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
struct clk_hw clk_pfd;
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
struct vc5_hw_data clk_pll;
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
struct vc5_hw_data clk_fod[VC5_MAX_FOD_NUM];
struct vc5_hw_data clk_out[VC5_MAX_CLK_OUT_NUM];
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
};
static const char * const vc5_mux_names[] = {
"mux"
};
clk: vc5: Add support for the input frequency doubler The VersaClock 6 has an input frequency doubler between the input clock mux and the predivider. Add new capability flag and support for this frequency doubler block into the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:12 +08:00
static const char * const vc5_dbl_names[] = {
"dbl"
};
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
static const char * const vc5_pfd_names[] = {
"pfd"
};
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
static const char * const vc5_pll_names[] = {
"pll"
};
static const char * const vc5_fod_names[] = {
"fod0", "fod1", "fod2", "fod3",
};
static const char * const vc5_clk_out_names[] = {
"out0_sel_i2cb", "out1", "out2", "out3", "out4",
};
/*
* VersaClock5 i2c regmap
*/
static bool vc5_regmap_is_writeable(struct device *dev, unsigned int reg)
{
/* Factory reserved regs, make them read-only */
if (reg <= 0xf)
return false;
/* Factory reserved regs, make them read-only */
if (reg == 0x14 || reg == 0x1c || reg == 0x1d)
return false;
return true;
}
static const struct regmap_config vc5_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.cache_type = REGCACHE_RBTREE,
.max_register = 0x76,
.writeable_reg = vc5_regmap_is_writeable,
};
/*
* VersaClock5 input multiplexer between XTAL and CLKIN divider
*/
static unsigned char vc5_mux_get_parent(struct clk_hw *hw)
{
struct vc5_driver_data *vc5 =
container_of(hw, struct vc5_driver_data, clk_mux);
const u8 mask = VC5_PRIM_SRC_SHDN_EN_XTAL | VC5_PRIM_SRC_SHDN_EN_CLKIN;
unsigned int src;
regmap_read(vc5->regmap, VC5_PRIM_SRC_SHDN, &src);
src &= mask;
if (src == VC5_PRIM_SRC_SHDN_EN_XTAL)
return 0;
if (src == VC5_PRIM_SRC_SHDN_EN_CLKIN)
return 1;
dev_warn(&vc5->client->dev,
"Invalid clock input configuration (%02x)\n", src);
return 0;
}
static int vc5_mux_set_parent(struct clk_hw *hw, u8 index)
{
struct vc5_driver_data *vc5 =
container_of(hw, struct vc5_driver_data, clk_mux);
const u8 mask = VC5_PRIM_SRC_SHDN_EN_XTAL | VC5_PRIM_SRC_SHDN_EN_CLKIN;
u8 src;
if ((index > 1) || !vc5->clk_mux_ins)
return -EINVAL;
if (vc5->clk_mux_ins == (VC5_MUX_IN_CLKIN | VC5_MUX_IN_XIN)) {
if (index == 0)
src = VC5_PRIM_SRC_SHDN_EN_XTAL;
if (index == 1)
src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
} else {
if (index != 0)
return -EINVAL;
if (vc5->clk_mux_ins == VC5_MUX_IN_XIN)
src = VC5_PRIM_SRC_SHDN_EN_XTAL;
if (vc5->clk_mux_ins == VC5_MUX_IN_CLKIN)
src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
}
return regmap_update_bits(vc5->regmap, VC5_PRIM_SRC_SHDN, mask, src);
}
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
static const struct clk_ops vc5_mux_ops = {
.set_parent = vc5_mux_set_parent,
.get_parent = vc5_mux_get_parent,
};
clk: vc5: Add support for the input frequency doubler The VersaClock 6 has an input frequency doubler between the input clock mux and the predivider. Add new capability flag and support for this frequency doubler block into the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:12 +08:00
static unsigned long vc5_dbl_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
struct vc5_driver_data *vc5 =
container_of(hw, struct vc5_driver_data, clk_mul);
unsigned int premul;
regmap_read(vc5->regmap, VC5_PRIM_SRC_SHDN, &premul);
if (premul & VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ)
parent_rate *= 2;
return parent_rate;
}
static long vc5_dbl_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long *parent_rate)
{
if ((*parent_rate == rate) || ((*parent_rate * 2) == rate))
return rate;
else
return -EINVAL;
}
static int vc5_dbl_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate)
{
struct vc5_driver_data *vc5 =
container_of(hw, struct vc5_driver_data, clk_mul);
u32 mask;
if ((parent_rate * 2) == rate)
mask = VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ;
else
mask = 0;
regmap_update_bits(vc5->regmap, VC5_PRIM_SRC_SHDN,
VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ,
mask);
return 0;
}
static const struct clk_ops vc5_dbl_ops = {
.recalc_rate = vc5_dbl_recalc_rate,
.round_rate = vc5_dbl_round_rate,
.set_rate = vc5_dbl_set_rate,
};
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
static unsigned long vc5_pfd_recalc_rate(struct clk_hw *hw,
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
unsigned long parent_rate)
{
struct vc5_driver_data *vc5 =
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
container_of(hw, struct vc5_driver_data, clk_pfd);
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
unsigned int prediv, div;
regmap_read(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV, &prediv);
/* The bypass_prediv is set, PLL fed from Ref_in directly. */
if (prediv & VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV)
return parent_rate;
regmap_read(vc5->regmap, VC5_REF_DIVIDER, &div);
/* The Sel_prediv2 is set, PLL fed from prediv2 (Ref_in / 2) */
if (div & VC5_REF_DIVIDER_SEL_PREDIV2)
return parent_rate / 2;
else
return parent_rate / VC5_REF_DIVIDER_REF_DIV(div);
}
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
static long vc5_pfd_round_rate(struct clk_hw *hw, unsigned long rate,
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
unsigned long *parent_rate)
{
unsigned long idiv;
/* PLL cannot operate with input clock above 50 MHz. */
if (rate > 50000000)
return -EINVAL;
/* CLKIN within range of PLL input, feed directly to PLL. */
if (*parent_rate <= 50000000)
return *parent_rate;
idiv = DIV_ROUND_UP(*parent_rate, rate);
if (idiv > 127)
return -EINVAL;
return *parent_rate / idiv;
}
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
static int vc5_pfd_set_rate(struct clk_hw *hw, unsigned long rate,
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
unsigned long parent_rate)
{
struct vc5_driver_data *vc5 =
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
container_of(hw, struct vc5_driver_data, clk_pfd);
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
unsigned long idiv;
u8 div;
/* CLKIN within range of PLL input, feed directly to PLL. */
if (parent_rate <= 50000000) {
regmap_update_bits(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV,
VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV,
VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV);
regmap_update_bits(vc5->regmap, VC5_REF_DIVIDER, 0xff, 0x00);
return 0;
}
idiv = DIV_ROUND_UP(parent_rate, rate);
/* We have dedicated div-2 predivider. */
if (idiv == 2)
div = VC5_REF_DIVIDER_SEL_PREDIV2;
else
div = VC5_REF_DIVIDER_REF_DIV(idiv);
regmap_update_bits(vc5->regmap, VC5_REF_DIVIDER, 0xff, div);
regmap_update_bits(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV,
VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV, 0);
return 0;
}
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
static const struct clk_ops vc5_pfd_ops = {
.recalc_rate = vc5_pfd_recalc_rate,
.round_rate = vc5_pfd_round_rate,
.set_rate = vc5_pfd_set_rate,
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
};
/*
* VersaClock5 PLL/VCO
*/
static unsigned long vc5_pll_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
u32 div_int, div_frc;
u8 fb[5];
regmap_bulk_read(vc5->regmap, VC5_FEEDBACK_INT_DIV, fb, 5);
div_int = (fb[0] << 4) | (fb[1] >> 4);
div_frc = (fb[2] << 16) | (fb[3] << 8) | fb[4];
/* The PLL divider has 12 integer bits and 24 fractional bits */
return (parent_rate * div_int) + ((parent_rate * div_frc) >> 24);
}
static long vc5_pll_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long *parent_rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
u32 div_int;
u64 div_frc;
if (rate < VC5_PLL_VCO_MIN)
rate = VC5_PLL_VCO_MIN;
if (rate > VC5_PLL_VCO_MAX)
rate = VC5_PLL_VCO_MAX;
/* Determine integer part, which is 12 bit wide */
div_int = rate / *parent_rate;
if (div_int > 0xfff)
rate = *parent_rate * 0xfff;
/* Determine best fractional part, which is 24 bit wide */
div_frc = rate % *parent_rate;
div_frc *= BIT(24) - 1;
do_div(div_frc, *parent_rate);
hwdata->div_int = div_int;
hwdata->div_frc = (u32)div_frc;
return (*parent_rate * div_int) + ((*parent_rate * div_frc) >> 24);
}
static int vc5_pll_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
u8 fb[5];
fb[0] = hwdata->div_int >> 4;
fb[1] = hwdata->div_int << 4;
fb[2] = hwdata->div_frc >> 16;
fb[3] = hwdata->div_frc >> 8;
fb[4] = hwdata->div_frc;
return regmap_bulk_write(vc5->regmap, VC5_FEEDBACK_INT_DIV, fb, 5);
}
static const struct clk_ops vc5_pll_ops = {
.recalc_rate = vc5_pll_recalc_rate,
.round_rate = vc5_pll_round_rate,
.set_rate = vc5_pll_set_rate,
};
static unsigned long vc5_fod_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
/* VCO frequency is divided by two before entering FOD */
u32 f_in = parent_rate / 2;
u32 div_int, div_frc;
u8 od_int[2];
u8 od_frc[4];
regmap_bulk_read(vc5->regmap, VC5_OUT_DIV_INT(hwdata->num, 0),
od_int, 2);
regmap_bulk_read(vc5->regmap, VC5_OUT_DIV_FRAC(hwdata->num, 0),
od_frc, 4);
div_int = (od_int[0] << 4) | (od_int[1] >> 4);
div_frc = (od_frc[0] << 22) | (od_frc[1] << 14) |
(od_frc[2] << 6) | (od_frc[3] >> 2);
clk: vc5: Prevent division by zero on unconfigured outputs In case the initial values of the FOD registers are not configured in the OTP or by the bootloader, it is possible that the FOD registers will contain zeroes. The code in vc5_fod_recalc_rate() immediately feeds the FOD divider value obtained from the FOD registers into the div64_u64() and if the FOD divider value is zero, triggers division by zero exception. Check if the FOD divider value is zero and return the frequency of the FOD output as 0 Hz if it is so. This prevents the division by zero exception. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:07 +08:00
/* Avoid division by zero if the output is not configured. */
if (div_int == 0 && div_frc == 0)
return 0;
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
/* The PLL divider has 12 integer bits and 30 fractional bits */
return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
}
static long vc5_fod_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long *parent_rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
/* VCO frequency is divided by two before entering FOD */
u32 f_in = *parent_rate / 2;
u32 div_int;
u64 div_frc;
/* Determine integer part, which is 12 bit wide */
div_int = f_in / rate;
/*
* WARNING: The clock chip does not output signal if the integer part
* of the divider is 0xfff and fractional part is non-zero.
* Clamp the divider at 0xffe to keep the code simple.
*/
if (div_int > 0xffe) {
div_int = 0xffe;
rate = f_in / div_int;
}
/* Determine best fractional part, which is 30 bit wide */
div_frc = f_in % rate;
div_frc <<= 24;
do_div(div_frc, rate);
hwdata->div_int = div_int;
hwdata->div_frc = (u32)div_frc;
return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
}
static int vc5_fod_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
u8 data[14] = {
hwdata->div_frc >> 22, hwdata->div_frc >> 14,
hwdata->div_frc >> 6, hwdata->div_frc << 2,
0, 0, 0, 0, 0,
0, 0,
hwdata->div_int >> 4, hwdata->div_int << 4,
0
};
regmap_bulk_write(vc5->regmap, VC5_OUT_DIV_FRAC(hwdata->num, 0),
data, 14);
/*
* Toggle magic bit in undocumented register for unknown reason.
* This is what the IDT timing commander tool does and the chip
* datasheet somewhat implies this is needed, but the register
* and the bit is not documented.
*/
regmap_update_bits(vc5->regmap, VC5_GLOBAL_REGISTER,
VC5_GLOBAL_REGISTER_GLOBAL_RESET, 0);
regmap_update_bits(vc5->regmap, VC5_GLOBAL_REGISTER,
VC5_GLOBAL_REGISTER_GLOBAL_RESET,
VC5_GLOBAL_REGISTER_GLOBAL_RESET);
return 0;
}
static const struct clk_ops vc5_fod_ops = {
.recalc_rate = vc5_fod_recalc_rate,
.round_rate = vc5_fod_round_rate,
.set_rate = vc5_fod_set_rate,
};
static int vc5_clk_out_prepare(struct clk_hw *hw)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
clk: vc5: Configure the output buffer input mux on prepare The output buffer input mux can be configured in either of three states -- disabled, input from FOD, input from previous output. Once the .prepare() callback of the output buffer is called, the output buffer input mux must be set to either input from FOD or input from previous output, it cannot be set to Disabled anymore or the output won't work. Default to the input from FOD if the output buffer input mux was Disabled and the .prepare() was called on it. Note that we do not set the output buffer input mux back to Disabled in the .unprepare() callback as there is no obvious benefit of doing so. We disable the entire output buffer in the .unprepare() callback already. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:10 +08:00
const u8 mask = VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT |
VC5_OUT_DIV_CONTROL_EN_FOD;
unsigned int src;
int ret;
/*
* If the input mux is disabled, enable it first and
* select source from matching FOD.
*/
regmap_read(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num), &src);
if ((src & mask) == 0) {
src = VC5_OUT_DIV_CONTROL_RESET | VC5_OUT_DIV_CONTROL_EN_FOD;
ret = regmap_update_bits(vc5->regmap,
VC5_OUT_DIV_CONTROL(hwdata->num),
mask | VC5_OUT_DIV_CONTROL_RESET, src);
if (ret)
return ret;
}
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
/* Enable the clock buffer */
regmap_update_bits(vc5->regmap, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
VC5_CLK_OUTPUT_CFG1_EN_CLKBUF,
VC5_CLK_OUTPUT_CFG1_EN_CLKBUF);
return 0;
}
static void vc5_clk_out_unprepare(struct clk_hw *hw)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
clk: vc5: Fix trivial typo Fix trivial typo in vc5_clk_out_unprepare() , s/Enable/Disable/ . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:08 +08:00
/* Disable the clock buffer */
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
regmap_update_bits(vc5->regmap, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
VC5_CLK_OUTPUT_CFG1_EN_CLKBUF, 0);
}
static unsigned char vc5_clk_out_get_parent(struct clk_hw *hw)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
const u8 mask = VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT |
VC5_OUT_DIV_CONTROL_EN_FOD;
const u8 fodclkmask = VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_EN_FOD;
const u8 extclk = VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT;
unsigned int src;
regmap_read(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num), &src);
src &= mask;
clk: vc5: Do not warn about disabled output buffer input muxes The output buffer input mux can be configured in either of three states -- disabled, input from FOD, input from previous output. If the output buffer input mux is set to disabled, the code in vc5_clk_out_get_parent() would consider this an invalid setting and warn about it, which is not necessarily the case. In case the output buffer input mux is disabled, default to input from FOD to have some parent and don't print the warning. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:09 +08:00
if (src == 0) /* Input mux set to DISABLED */
return 0;
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
if ((src & fodclkmask) == VC5_OUT_DIV_CONTROL_EN_FOD)
return 0;
if (src == extclk)
return 1;
dev_warn(&vc5->client->dev,
"Invalid clock output configuration (%02x)\n", src);
return 0;
}
static int vc5_clk_out_set_parent(struct clk_hw *hw, u8 index)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
const u8 mask = VC5_OUT_DIV_CONTROL_RESET |
VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT |
VC5_OUT_DIV_CONTROL_EN_FOD;
const u8 extclk = VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT;
u8 src = VC5_OUT_DIV_CONTROL_RESET;
if (index == 0)
src |= VC5_OUT_DIV_CONTROL_EN_FOD;
else
src |= extclk;
return regmap_update_bits(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num),
mask, src);
}
static const struct clk_ops vc5_clk_out_ops = {
.prepare = vc5_clk_out_prepare,
.unprepare = vc5_clk_out_unprepare,
.set_parent = vc5_clk_out_set_parent,
.get_parent = vc5_clk_out_get_parent,
};
static struct clk_hw *vc5_of_clk_get(struct of_phandle_args *clkspec,
void *data)
{
struct vc5_driver_data *vc5 = data;
unsigned int idx = clkspec->args[0];
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
if (idx >= vc5->chip_info->clk_out_cnt)
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
return ERR_PTR(-EINVAL);
return &vc5->clk_out[idx].hw;
}
static int vc5_map_index_to_output(const enum vc5_model model,
const unsigned int n)
{
switch (model) {
case IDT_VC5_5P49V5933:
return (n == 0) ? 0 : 3;
case IDT_VC5_5P49V5923:
clk: vc5: Add support for IDT VersaClock 5P49V5925 Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only external clock input, four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-10 01:39:57 +08:00
case IDT_VC5_5P49V5925:
clk: vc5: Add support for IDT VersaClock 5P49V5935 Update IDT VersaClock 5 driver to support 5P49V5935. This chip has two clock inputs (internal XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Current driver supports up to 2 FODs and up to 3 clock outputs. This patch sets max number of supported FODs to 4 and max number of supported clock outputs to 5. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:24 +08:00
case IDT_VC5_5P49V5935:
clk: vc5: Add support for IDT VersaClock 5P49V6901 Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901. This chip has two clock inputs (external XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:14 +08:00
case IDT_VC6_5P49V6901:
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
default:
return n;
}
}
static const struct of_device_id clk_vc5_of_match[];
static int vc5_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct vc5_driver_data *vc5;
struct clk_init_data init;
const char *parent_names[2];
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
unsigned int n, idx = 0;
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
int ret;
vc5 = devm_kzalloc(&client->dev, sizeof(*vc5), GFP_KERNEL);
if (vc5 == NULL)
return -ENOMEM;
i2c_set_clientdata(client, vc5);
vc5->client = client;
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
vc5->chip_info = of_device_get_match_data(&client->dev);
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
vc5->pin_xin = devm_clk_get(&client->dev, "xin");
if (PTR_ERR(vc5->pin_xin) == -EPROBE_DEFER)
return -EPROBE_DEFER;
vc5->pin_clkin = devm_clk_get(&client->dev, "clkin");
if (PTR_ERR(vc5->pin_clkin) == -EPROBE_DEFER)
return -EPROBE_DEFER;
vc5->regmap = devm_regmap_init_i2c(client, &vc5_regmap_config);
if (IS_ERR(vc5->regmap)) {
dev_err(&client->dev, "failed to allocate register map\n");
return PTR_ERR(vc5->regmap);
}
/* Register clock input mux */
memset(&init, 0, sizeof(init));
if (!IS_ERR(vc5->pin_xin)) {
vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
} else if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL) {
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
vc5->pin_xin = clk_register_fixed_rate(&client->dev,
"internal-xtal", NULL,
0, 25000000);
if (IS_ERR(vc5->pin_xin))
return PTR_ERR(vc5->pin_xin);
vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
}
if (!IS_ERR(vc5->pin_clkin)) {
vc5->clk_mux_ins |= VC5_MUX_IN_CLKIN;
parent_names[init.num_parents++] =
__clk_get_name(vc5->pin_clkin);
}
if (!init.num_parents) {
dev_err(&client->dev, "no input clock specified!\n");
return -EINVAL;
}
init.name = vc5_mux_names[0];
init.ops = &vc5_mux_ops;
init.flags = 0;
init.parent_names = parent_names;
vc5->clk_mux.init = &init;
ret = devm_clk_hw_register(&client->dev, &vc5->clk_mux);
if (ret) {
dev_err(&client->dev, "unable to register %s\n", init.name);
goto err_clk;
}
clk: vc5: Add support for the input frequency doubler The VersaClock 6 has an input frequency doubler between the input clock mux and the predivider. Add new capability flag and support for this frequency doubler block into the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:12 +08:00
if (vc5->chip_info->flags & VC5_HAS_PFD_FREQ_DBL) {
/* Register frequency doubler */
memset(&init, 0, sizeof(init));
init.name = vc5_dbl_names[0];
init.ops = &vc5_dbl_ops;
init.flags = CLK_SET_RATE_PARENT;
init.parent_names = vc5_mux_names;
init.num_parents = 1;
vc5->clk_mul.init = &init;
ret = devm_clk_hw_register(&client->dev, &vc5->clk_mul);
if (ret) {
dev_err(&client->dev, "unable to register %s\n",
init.name);
goto err_clk;
}
}
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
/* Register PFD */
memset(&init, 0, sizeof(init));
init.name = vc5_pfd_names[0];
init.ops = &vc5_pfd_ops;
init.flags = CLK_SET_RATE_PARENT;
clk: vc5: Add support for the input frequency doubler The VersaClock 6 has an input frequency doubler between the input clock mux and the predivider. Add new capability flag and support for this frequency doubler block into the driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:12 +08:00
if (vc5->chip_info->flags & VC5_HAS_PFD_FREQ_DBL)
init.parent_names = vc5_dbl_names;
else
init.parent_names = vc5_mux_names;
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
init.num_parents = 1;
vc5->clk_pfd.init = &init;
ret = devm_clk_hw_register(&client->dev, &vc5->clk_pfd);
if (ret) {
dev_err(&client->dev, "unable to register %s\n", init.name);
goto err_clk;
}
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
/* Register PLL */
memset(&init, 0, sizeof(init));
init.name = vc5_pll_names[0];
init.ops = &vc5_pll_ops;
init.flags = CLK_SET_RATE_PARENT;
clk: vc5: Split clock input mux and predivider Split the VC5 clock input mux and the predivider to more accurately model the hardware and fix the previously incorrect assumption that both the OUT_SEL_I2CB and the PLL are fed from the predivider. It is in fact the clock input mux output which is directly feeding the clock into the OUT_SEL_I2CB output, while the clock input mux output first passes through the predivider before it is fed into the PLL. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:11 +08:00
init.parent_names = vc5_pfd_names;
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
init.num_parents = 1;
vc5->clk_pll.num = 0;
vc5->clk_pll.vc5 = vc5;
vc5->clk_pll.hw.init = &init;
ret = devm_clk_hw_register(&client->dev, &vc5->clk_pll.hw);
if (ret) {
dev_err(&client->dev, "unable to register %s\n", init.name);
goto err_clk;
}
/* Register FODs */
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
for (n = 0; n < vc5->chip_info->clk_fod_cnt; n++) {
idx = vc5_map_index_to_output(vc5->chip_info->model, n);
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
memset(&init, 0, sizeof(init));
init.name = vc5_fod_names[idx];
init.ops = &vc5_fod_ops;
init.flags = CLK_SET_RATE_PARENT;
init.parent_names = vc5_pll_names;
init.num_parents = 1;
vc5->clk_fod[n].num = idx;
vc5->clk_fod[n].vc5 = vc5;
vc5->clk_fod[n].hw.init = &init;
ret = devm_clk_hw_register(&client->dev, &vc5->clk_fod[n].hw);
if (ret) {
dev_err(&client->dev, "unable to register %s\n",
init.name);
goto err_clk;
}
}
/* Register MUX-connected OUT0_I2C_SELB output */
memset(&init, 0, sizeof(init));
init.name = vc5_clk_out_names[0];
init.ops = &vc5_clk_out_ops;
init.flags = CLK_SET_RATE_PARENT;
init.parent_names = vc5_mux_names;
init.num_parents = 1;
vc5->clk_out[0].num = idx;
vc5->clk_out[0].vc5 = vc5;
vc5->clk_out[0].hw.init = &init;
ret = devm_clk_hw_register(&client->dev, &vc5->clk_out[0].hw);
if (ret) {
dev_err(&client->dev, "unable to register %s\n",
init.name);
goto err_clk;
}
/* Register FOD-connected OUTx outputs */
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
for (n = 1; n < vc5->chip_info->clk_out_cnt; n++) {
idx = vc5_map_index_to_output(vc5->chip_info->model, n - 1);
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
parent_names[0] = vc5_fod_names[idx];
if (n == 1)
parent_names[1] = vc5_mux_names[0];
else
parent_names[1] = vc5_clk_out_names[n - 1];
memset(&init, 0, sizeof(init));
init.name = vc5_clk_out_names[idx + 1];
init.ops = &vc5_clk_out_ops;
init.flags = CLK_SET_RATE_PARENT;
init.parent_names = parent_names;
init.num_parents = 2;
vc5->clk_out[n].num = idx;
vc5->clk_out[n].vc5 = vc5;
vc5->clk_out[n].hw.init = &init;
ret = devm_clk_hw_register(&client->dev,
&vc5->clk_out[n].hw);
if (ret) {
dev_err(&client->dev, "unable to register %s\n",
init.name);
goto err_clk;
}
}
ret = of_clk_add_hw_provider(client->dev.of_node, vc5_of_clk_get, vc5);
if (ret) {
dev_err(&client->dev, "unable to add clk provider\n");
goto err_clk;
}
return 0;
err_clk:
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL)
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
clk_unregister_fixed_rate(vc5->pin_xin);
return ret;
}
static int vc5_remove(struct i2c_client *client)
{
struct vc5_driver_data *vc5 = i2c_get_clientdata(client);
of_clk_del_provider(client->dev.of_node);
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL)
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
clk_unregister_fixed_rate(vc5->pin_xin);
return 0;
}
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
static const struct vc5_chip_info idt_5p49v5923_info = {
.model = IDT_VC5_5P49V5923,
.clk_fod_cnt = 2,
.clk_out_cnt = 3,
.flags = 0,
};
clk: vc5: Add support for IDT VersaClock 5P49V5925 Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only external clock input, four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-10 01:39:57 +08:00
static const struct vc5_chip_info idt_5p49v5925_info = {
.model = IDT_VC5_5P49V5925,
.clk_fod_cnt = 4,
.clk_out_cnt = 5,
.flags = 0,
};
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
static const struct vc5_chip_info idt_5p49v5933_info = {
.model = IDT_VC5_5P49V5933,
.clk_fod_cnt = 2,
.clk_out_cnt = 3,
.flags = VC5_HAS_INTERNAL_XTAL,
};
clk: vc5: Add support for IDT VersaClock 5P49V5935 Update IDT VersaClock 5 driver to support 5P49V5935. This chip has two clock inputs (internal XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Current driver supports up to 2 FODs and up to 3 clock outputs. This patch sets max number of supported FODs to 4 and max number of supported clock outputs to 5. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:24 +08:00
static const struct vc5_chip_info idt_5p49v5935_info = {
.model = IDT_VC5_5P49V5935,
.clk_fod_cnt = 4,
.clk_out_cnt = 5,
.flags = VC5_HAS_INTERNAL_XTAL,
};
clk: vc5: Add support for IDT VersaClock 5P49V6901 Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901. This chip has two clock inputs (external XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:14 +08:00
static const struct vc5_chip_info idt_5p49v6901_info = {
.model = IDT_VC6_5P49V6901,
.clk_fod_cnt = 4,
.clk_out_cnt = 5,
.flags = VC5_HAS_PFD_FREQ_DBL,
};
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
static const struct i2c_device_id vc5_id[] = {
{ "5p49v5923", .driver_data = IDT_VC5_5P49V5923 },
clk: vc5: Add support for IDT VersaClock 5P49V5925 Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only external clock input, four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-10 01:39:57 +08:00
{ "5p49v5925", .driver_data = IDT_VC5_5P49V5925 },
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
{ "5p49v5933", .driver_data = IDT_VC5_5P49V5933 },
clk: vc5: Add support for IDT VersaClock 5P49V5935 Update IDT VersaClock 5 driver to support 5P49V5935. This chip has two clock inputs (internal XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Current driver supports up to 2 FODs and up to 3 clock outputs. This patch sets max number of supported FODs to 4 and max number of supported clock outputs to 5. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:24 +08:00
{ "5p49v5935", .driver_data = IDT_VC5_5P49V5935 },
clk: vc5: Add support for IDT VersaClock 5P49V6901 Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901. This chip has two clock inputs (external XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:14 +08:00
{ "5p49v6901", .driver_data = IDT_VC6_5P49V6901 },
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
{ }
};
MODULE_DEVICE_TABLE(i2c, vc5_id);
static const struct of_device_id clk_vc5_of_match[] = {
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
{ .compatible = "idt,5p49v5923", .data = &idt_5p49v5923_info },
clk: vc5: Add support for IDT VersaClock 5P49V5925 Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only external clock input, four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-10 01:39:57 +08:00
{ .compatible = "idt,5p49v5925", .data = &idt_5p49v5925_info },
clk: vc5: Add structure to describe particular chip features Introduce vc5_chip_info structure to describe features of a particular VC5 chip (id, number of FODs, number of outputs, flags). For now flags are only used to indicate if chip has internal XTAL. vc5_chip_info is set on probe from the matched of_device_id->data. Also add defines to specify maximum number of FODs and clock outputs supported by the driver. With these changes it should be easier to extend driver to support more VC5 models. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:22 +08:00
{ .compatible = "idt,5p49v5933", .data = &idt_5p49v5933_info },
clk: vc5: Add support for IDT VersaClock 5P49V5935 Update IDT VersaClock 5 driver to support 5P49V5935. This chip has two clock inputs (internal XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Current driver supports up to 2 FODs and up to 3 clock outputs. This patch sets max number of supported FODs to 4 and max number of supported clock outputs to 5. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-04-07 17:12:24 +08:00
{ .compatible = "idt,5p49v5935", .data = &idt_5p49v5935_info },
clk: vc5: Add support for IDT VersaClock 5P49V6901 Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901. This chip has two clock inputs (external XTAL or external CLKIN), four fractional dividers (FODs) and five clock outputs (four universal clock outputs and one reference clock output at OUT0_SELB_I2C). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> on Salvator-XS with the display LVDS output. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-07-09 21:28:14 +08:00
{ .compatible = "idt,5p49v6901", .data = &idt_5p49v6901_info },
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933 Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These chips have two clock inputs, XTAL or CLK, which are muxed into single PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip while the 5P49V5923 requires external XTAL. The PLL feeds two fractional dividers. Each fractional divider feeds output mux, which allows selecting between clock from the fractional divider itself or from output mux on output N-1. In case of output mux 0, the output N-1 is instead connected to the output from the mux feeding the PLL. The driver thus far supports only the 5P49V5923 and 5P49V5933, while it should be easily extensible to the whole 5P49V59xx family of chips as they are all pretty similar. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Michael Turquette <mturquette@baylibre.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2017-01-12 09:03:24 +08:00
{ },
};
MODULE_DEVICE_TABLE(of, clk_vc5_of_match);
static struct i2c_driver vc5_driver = {
.driver = {
.name = "vc5",
.of_match_table = clk_vc5_of_match,
},
.probe = vc5_probe,
.remove = vc5_remove,
.id_table = vc5_id,
};
module_i2c_driver(vc5_driver);
MODULE_AUTHOR("Marek Vasut <marek.vasut@gmail.com>");
MODULE_DESCRIPTION("IDT VersaClock 5 driver");
MODULE_LICENSE("GPL");