2021-08-03 01:23:09 +08:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
/*
|
|
|
|
* datasheet: https://www.nxp.com/docs/en/data-sheet/K20P144M120SF3.pdf
|
|
|
|
*
|
|
|
|
* Copyright (C) 2018-2021 Collabora
|
|
|
|
* Copyright (C) 2018-2021 GE Healthcare
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <linux/delay.h>
|
|
|
|
#include <linux/firmware.h>
|
|
|
|
#include <linux/gpio/consumer.h>
|
|
|
|
#include <linux/kernel.h>
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/of.h>
|
|
|
|
#include <linux/spi/spi.h>
|
|
|
|
|
|
|
|
#define ACHC_MAX_FREQ_HZ 300000
|
|
|
|
#define ACHC_FAST_READ_FREQ_HZ 1000000
|
|
|
|
|
|
|
|
struct achc_data {
|
|
|
|
struct spi_device *main;
|
|
|
|
struct spi_device *ezport;
|
|
|
|
struct gpio_desc *reset;
|
|
|
|
|
|
|
|
struct mutex device_lock; /* avoid concurrent device access */
|
|
|
|
};
|
|
|
|
|
|
|
|
#define EZPORT_RESET_DELAY_MS 100
|
|
|
|
#define EZPORT_STARTUP_DELAY_MS 200
|
|
|
|
#define EZPORT_WRITE_WAIT_MS 10
|
|
|
|
#define EZPORT_TRANSFER_SIZE 2048
|
|
|
|
|
|
|
|
#define EZPORT_CMD_SP 0x02 /* flash section program */
|
|
|
|
#define EZPORT_CMD_RDSR 0x05 /* read status register */
|
|
|
|
#define EZPORT_CMD_WREN 0x06 /* write enable */
|
|
|
|
#define EZPORT_CMD_FAST_READ 0x0b /* flash read data at high speed */
|
|
|
|
#define EZPORT_CMD_RESET 0xb9 /* reset chip */
|
|
|
|
#define EZPORT_CMD_BE 0xc7 /* bulk erase */
|
|
|
|
#define EZPORT_CMD_SE 0xd8 /* sector erase */
|
|
|
|
|
|
|
|
#define EZPORT_SECTOR_SIZE 4096
|
|
|
|
#define EZPORT_SECTOR_MASK (EZPORT_SECTOR_SIZE - 1)
|
|
|
|
|
|
|
|
#define EZPORT_STATUS_WIP BIT(0) /* write in progress */
|
|
|
|
#define EZPORT_STATUS_WEN BIT(1) /* write enable */
|
|
|
|
#define EZPORT_STATUS_BEDIS BIT(2) /* bulk erase disable */
|
|
|
|
#define EZPORT_STATUS_FLEXRAM BIT(3) /* FlexRAM mode */
|
|
|
|
#define EZPORT_STATUS_WEF BIT(6) /* write error flag */
|
|
|
|
#define EZPORT_STATUS_FS BIT(7) /* flash security */
|
|
|
|
|
|
|
|
static void ezport_reset(struct gpio_desc *reset)
|
|
|
|
{
|
|
|
|
gpiod_set_value(reset, 1);
|
|
|
|
msleep(EZPORT_RESET_DELAY_MS);
|
|
|
|
gpiod_set_value(reset, 0);
|
|
|
|
msleep(EZPORT_STARTUP_DELAY_MS);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_start_programming(struct spi_device *spi, struct gpio_desc *reset)
|
|
|
|
{
|
|
|
|
struct spi_message msg;
|
|
|
|
struct spi_transfer assert_cs = {
|
|
|
|
.cs_change = 1,
|
|
|
|
};
|
|
|
|
struct spi_transfer release_cs = { };
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
spi_bus_lock(spi->master);
|
|
|
|
|
|
|
|
/* assert chip select */
|
|
|
|
spi_message_init(&msg);
|
|
|
|
spi_message_add_tail(&assert_cs, &msg);
|
|
|
|
ret = spi_sync_locked(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
msleep(EZPORT_STARTUP_DELAY_MS);
|
|
|
|
|
|
|
|
/* reset with asserted chip select to switch into programming mode */
|
|
|
|
ezport_reset(reset);
|
|
|
|
|
|
|
|
/* release chip select */
|
|
|
|
spi_message_init(&msg);
|
|
|
|
spi_message_add_tail(&release_cs, &msg);
|
|
|
|
ret = spi_sync_locked(spi, &msg);
|
|
|
|
|
|
|
|
fail:
|
|
|
|
spi_bus_unlock(spi->master);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static void ezport_stop_programming(struct spi_device *spi, struct gpio_desc *reset)
|
|
|
|
{
|
|
|
|
/* reset without asserted chip select to return into normal mode */
|
|
|
|
spi_bus_lock(spi->master);
|
|
|
|
ezport_reset(reset);
|
|
|
|
spi_bus_unlock(spi->master);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_get_status_register(struct spi_device *spi)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = spi_w8r8(spi, EZPORT_CMD_RDSR);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
if (ret == 0xff) {
|
|
|
|
dev_err(&spi->dev, "Invalid EzPort status, EzPort is not functional!\n");
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_soft_reset(struct spi_device *spi)
|
|
|
|
{
|
|
|
|
u8 cmd = EZPORT_CMD_RESET;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = spi_write(spi, &cmd, 1);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
msleep(EZPORT_STARTUP_DELAY_MS);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_send_simple(struct spi_device *spi, u8 cmd)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = spi_write(spi, &cmd, 1);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return ezport_get_status_register(spi);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_wait_write(struct spi_device *spi, u32 retries)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
u32 i;
|
|
|
|
|
|
|
|
for (i = 0; i < retries; i++) {
|
|
|
|
ret = ezport_get_status_register(spi);
|
|
|
|
if (ret >= 0 && !(ret & EZPORT_STATUS_WIP))
|
|
|
|
break;
|
|
|
|
msleep(EZPORT_WRITE_WAIT_MS);
|
|
|
|
}
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_write_enable(struct spi_device *spi)
|
|
|
|
{
|
|
|
|
int ret = 0, retries = 3;
|
|
|
|
|
|
|
|
for (retries = 0; retries < 3; retries++) {
|
|
|
|
ret = ezport_send_simple(spi, EZPORT_CMD_WREN);
|
|
|
|
if (ret > 0 && ret & EZPORT_STATUS_WEN)
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (!(ret & EZPORT_STATUS_WEN)) {
|
|
|
|
dev_err(&spi->dev, "EzPort write enable timed out\n");
|
|
|
|
return -ETIMEDOUT;
|
|
|
|
}
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_bulk_erase(struct spi_device *spi)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
static const u8 cmd = EZPORT_CMD_BE;
|
|
|
|
|
|
|
|
dev_dbg(&spi->dev, "EzPort bulk erase...\n");
|
|
|
|
|
|
|
|
ret = ezport_write_enable(spi);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
ret = spi_write(spi, &cmd, 1);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
ret = ezport_wait_write(spi, 1000);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_section_erase(struct spi_device *spi, u32 address)
|
|
|
|
{
|
|
|
|
u8 query[] = {EZPORT_CMD_SE, (address >> 16) & 0xff, (address >> 8) & 0xff, address & 0xff};
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
dev_dbg(&spi->dev, "Ezport section erase @ 0x%06x...\n", address);
|
|
|
|
|
|
|
|
if (address & EZPORT_SECTOR_MASK)
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
ret = ezport_write_enable(spi);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
ret = spi_write(spi, query, sizeof(query));
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return ezport_wait_write(spi, 200);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_flash_transfer(struct spi_device *spi, u32 address,
|
|
|
|
const u8 *payload, size_t payload_size)
|
|
|
|
{
|
|
|
|
struct spi_transfer xfers[2] = {};
|
|
|
|
u8 *command;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
dev_dbg(&spi->dev, "EzPort write %zu bytes @ 0x%06x...\n", payload_size, address);
|
|
|
|
|
|
|
|
ret = ezport_write_enable(spi);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
command = kmalloc(4, GFP_KERNEL | GFP_DMA);
|
|
|
|
if (!command)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
command[0] = EZPORT_CMD_SP;
|
|
|
|
command[1] = address >> 16;
|
|
|
|
command[2] = address >> 8;
|
|
|
|
command[3] = address >> 0;
|
|
|
|
|
|
|
|
xfers[0].tx_buf = command;
|
|
|
|
xfers[0].len = 4;
|
|
|
|
|
|
|
|
xfers[1].tx_buf = payload;
|
|
|
|
xfers[1].len = payload_size;
|
|
|
|
|
|
|
|
ret = spi_sync_transfer(spi, xfers, 2);
|
|
|
|
kfree(command);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return ezport_wait_write(spi, 40);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_flash_compare(struct spi_device *spi, u32 address,
|
|
|
|
const u8 *payload, size_t payload_size)
|
|
|
|
{
|
|
|
|
struct spi_transfer xfers[2] = {};
|
|
|
|
u8 *buffer;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
buffer = kmalloc(payload_size + 5, GFP_KERNEL | GFP_DMA);
|
|
|
|
if (!buffer)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
buffer[0] = EZPORT_CMD_FAST_READ;
|
|
|
|
buffer[1] = address >> 16;
|
|
|
|
buffer[2] = address >> 8;
|
|
|
|
buffer[3] = address >> 0;
|
|
|
|
|
|
|
|
xfers[0].tx_buf = buffer;
|
|
|
|
xfers[0].len = 4;
|
|
|
|
xfers[0].speed_hz = ACHC_FAST_READ_FREQ_HZ;
|
|
|
|
|
|
|
|
xfers[1].rx_buf = buffer + 4;
|
|
|
|
xfers[1].len = payload_size + 1;
|
|
|
|
xfers[1].speed_hz = ACHC_FAST_READ_FREQ_HZ;
|
|
|
|
|
|
|
|
ret = spi_sync_transfer(spi, xfers, 2);
|
|
|
|
if (ret)
|
|
|
|
goto err;
|
|
|
|
|
|
|
|
/* FAST_READ receives one dummy byte before the real data */
|
|
|
|
ret = memcmp(payload, buffer + 4 + 1, payload_size);
|
|
|
|
if (ret) {
|
|
|
|
ret = -EBADMSG;
|
2021-08-16 05:42:06 +08:00
|
|
|
dev_dbg(&spi->dev, "Verification failure @ %06x", address);
|
2021-08-03 01:23:09 +08:00
|
|
|
print_hex_dump_bytes("fw: ", DUMP_PREFIX_OFFSET, payload, payload_size);
|
|
|
|
print_hex_dump_bytes("dev: ", DUMP_PREFIX_OFFSET, buffer + 4, payload_size);
|
|
|
|
}
|
|
|
|
|
|
|
|
err:
|
|
|
|
kfree(buffer);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_firmware_compare_data(struct spi_device *spi,
|
|
|
|
const u8 *data, size_t size)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
size_t address = 0;
|
|
|
|
size_t transfer_size;
|
|
|
|
|
|
|
|
dev_dbg(&spi->dev, "EzPort compare data with %zu bytes...\n", size);
|
|
|
|
|
|
|
|
ret = ezport_get_status_register(spi);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
if (ret & EZPORT_STATUS_FS) {
|
|
|
|
dev_info(&spi->dev, "Device is in secure mode (status=0x%02x)!\n", ret);
|
|
|
|
dev_info(&spi->dev, "FW verification is not possible\n");
|
|
|
|
return -EACCES;
|
|
|
|
}
|
|
|
|
|
|
|
|
while (size - address > 0) {
|
|
|
|
transfer_size = min((size_t) EZPORT_TRANSFER_SIZE, size - address);
|
|
|
|
|
|
|
|
ret = ezport_flash_compare(spi, address, data+address, transfer_size);
|
|
|
|
if (ret)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
address += transfer_size;
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_firmware_flash_data(struct spi_device *spi,
|
|
|
|
const u8 *data, size_t size)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
size_t address = 0;
|
|
|
|
size_t transfer_size;
|
|
|
|
|
|
|
|
dev_dbg(&spi->dev, "EzPort flash data with %zu bytes...\n", size);
|
|
|
|
|
|
|
|
ret = ezport_get_status_register(spi);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
if (ret & EZPORT_STATUS_FS) {
|
|
|
|
ret = ezport_bulk_erase(spi);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
if (ret & EZPORT_STATUS_FS)
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
|
|
|
while (size - address > 0) {
|
|
|
|
if (!(address & EZPORT_SECTOR_MASK)) {
|
|
|
|
ret = ezport_section_erase(spi, address);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
if (ret & EZPORT_STATUS_WIP || ret & EZPORT_STATUS_WEF)
|
|
|
|
return -EIO;
|
|
|
|
}
|
|
|
|
|
|
|
|
transfer_size = min((size_t) EZPORT_TRANSFER_SIZE, size - address);
|
|
|
|
|
|
|
|
ret = ezport_flash_transfer(spi, address,
|
|
|
|
data+address, transfer_size);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
else if (ret & EZPORT_STATUS_WIP)
|
|
|
|
return -ETIMEDOUT;
|
|
|
|
else if (ret & EZPORT_STATUS_WEF)
|
|
|
|
return -EIO;
|
|
|
|
|
|
|
|
address += transfer_size;
|
|
|
|
}
|
|
|
|
|
|
|
|
dev_dbg(&spi->dev, "EzPort verify flashed data...\n");
|
|
|
|
ret = ezport_firmware_compare_data(spi, data, size);
|
|
|
|
|
|
|
|
/* allow missing FW verfication in secure mode */
|
|
|
|
if (ret == -EACCES)
|
|
|
|
ret = 0;
|
|
|
|
|
|
|
|
if (ret < 0)
|
|
|
|
dev_err(&spi->dev, "Failed to verify flashed data: %d\n", ret);
|
|
|
|
|
|
|
|
ret = ezport_soft_reset(spi);
|
|
|
|
if (ret < 0)
|
|
|
|
dev_warn(&spi->dev, "EzPort reset failed!\n");
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ezport_firmware_load(struct spi_device *spi, const char *fwname)
|
|
|
|
{
|
|
|
|
const struct firmware *fw;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = request_firmware(&fw, fwname, &spi->dev);
|
|
|
|
if (ret) {
|
|
|
|
dev_err(&spi->dev, "Could not get firmware: %d\n", ret);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
ret = ezport_firmware_flash_data(spi, fw->data, fw->size);
|
|
|
|
|
|
|
|
release_firmware(fw);
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* ezport_flash - flash device firmware
|
|
|
|
* @spi: SPI device for NXP EzPort interface
|
|
|
|
* @reset: the gpio connected to the device reset pin
|
|
|
|
* @fwname: filename of the firmware that should be flashed
|
|
|
|
*
|
|
|
|
* Context: can sleep
|
|
|
|
*
|
|
|
|
* Return: 0 on success; negative errno on failure
|
|
|
|
*/
|
|
|
|
static int ezport_flash(struct spi_device *spi, struct gpio_desc *reset, const char *fwname)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = ezport_start_programming(spi, reset);
|
|
|
|
if (ret)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
ret = ezport_firmware_load(spi, fwname);
|
|
|
|
|
|
|
|
ezport_stop_programming(spi, reset);
|
|
|
|
|
|
|
|
if (ret)
|
|
|
|
dev_err(&spi->dev, "Failed to flash firmware: %d\n", ret);
|
|
|
|
else
|
|
|
|
dev_dbg(&spi->dev, "Finished FW flashing!\n");
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static ssize_t update_firmware_store(struct device *dev, struct device_attribute *attr,
|
|
|
|
const char *buf, size_t count)
|
|
|
|
{
|
|
|
|
struct achc_data *achc = dev_get_drvdata(dev);
|
|
|
|
unsigned long value;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = kstrtoul(buf, 0, &value);
|
|
|
|
if (ret < 0 || value != 1)
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
mutex_lock(&achc->device_lock);
|
|
|
|
ret = ezport_flash(achc->ezport, achc->reset, "achc.bin");
|
|
|
|
mutex_unlock(&achc->device_lock);
|
|
|
|
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return count;
|
|
|
|
}
|
|
|
|
static DEVICE_ATTR_WO(update_firmware);
|
|
|
|
|
|
|
|
static ssize_t reset_show(struct device *dev, struct device_attribute *attr, char *buf)
|
|
|
|
{
|
|
|
|
struct achc_data *achc = dev_get_drvdata(dev);
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
mutex_lock(&achc->device_lock);
|
|
|
|
ret = gpiod_get_value(achc->reset);
|
|
|
|
mutex_unlock(&achc->device_lock);
|
|
|
|
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return sysfs_emit(buf, "%d\n", ret);
|
|
|
|
}
|
|
|
|
|
|
|
|
static ssize_t reset_store(struct device *dev, struct device_attribute *attr,
|
|
|
|
const char *buf, size_t count)
|
|
|
|
{
|
|
|
|
struct achc_data *achc = dev_get_drvdata(dev);
|
|
|
|
unsigned long value;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = kstrtoul(buf, 0, &value);
|
|
|
|
if (ret < 0 || value > 1)
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
mutex_lock(&achc->device_lock);
|
|
|
|
gpiod_set_value(achc->reset, value);
|
|
|
|
mutex_unlock(&achc->device_lock);
|
|
|
|
|
|
|
|
return count;
|
|
|
|
}
|
|
|
|
static DEVICE_ATTR_RW(reset);
|
|
|
|
|
|
|
|
static struct attribute *gehc_achc_attrs[] = {
|
|
|
|
&dev_attr_update_firmware.attr,
|
|
|
|
&dev_attr_reset.attr,
|
|
|
|
NULL,
|
|
|
|
};
|
|
|
|
ATTRIBUTE_GROUPS(gehc_achc);
|
|
|
|
|
|
|
|
static void unregister_ezport(void *data)
|
|
|
|
{
|
|
|
|
struct spi_device *ezport = data;
|
|
|
|
|
|
|
|
spi_unregister_device(ezport);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int gehc_achc_probe(struct spi_device *spi)
|
|
|
|
{
|
|
|
|
struct achc_data *achc;
|
|
|
|
int ezport_reg, ret;
|
|
|
|
|
|
|
|
spi->max_speed_hz = ACHC_MAX_FREQ_HZ;
|
|
|
|
spi->bits_per_word = 8;
|
|
|
|
spi->mode = SPI_MODE_0;
|
|
|
|
|
|
|
|
achc = devm_kzalloc(&spi->dev, sizeof(*achc), GFP_KERNEL);
|
|
|
|
if (!achc)
|
|
|
|
return -ENOMEM;
|
|
|
|
spi_set_drvdata(spi, achc);
|
|
|
|
achc->main = spi;
|
|
|
|
|
|
|
|
mutex_init(&achc->device_lock);
|
|
|
|
|
|
|
|
ret = of_property_read_u32_index(spi->dev.of_node, "reg", 1, &ezport_reg);
|
|
|
|
if (ret)
|
|
|
|
return dev_err_probe(&spi->dev, ret, "missing second reg entry!\n");
|
|
|
|
|
|
|
|
achc->ezport = spi_new_ancillary_device(spi, ezport_reg);
|
|
|
|
if (IS_ERR(achc->ezport))
|
|
|
|
return PTR_ERR(achc->ezport);
|
|
|
|
|
|
|
|
ret = devm_add_action_or_reset(&spi->dev, unregister_ezport, achc->ezport);
|
|
|
|
if (ret)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
achc->reset = devm_gpiod_get(&spi->dev, "reset", GPIOD_OUT_LOW);
|
|
|
|
if (IS_ERR(achc->reset))
|
|
|
|
return dev_err_probe(&spi->dev, PTR_ERR(achc->reset), "Could not get reset gpio\n");
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static const struct spi_device_id gehc_achc_id[] = {
|
|
|
|
{ "ge,achc", 0 },
|
2021-09-24 03:46:09 +08:00
|
|
|
{ "achc", 0 },
|
2021-08-03 01:23:09 +08:00
|
|
|
{ }
|
|
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(spi, gehc_achc_id);
|
|
|
|
|
|
|
|
static const struct of_device_id gehc_achc_of_match[] = {
|
|
|
|
{ .compatible = "ge,achc" },
|
|
|
|
{ /* sentinel */ }
|
|
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(of, gehc_achc_of_match);
|
|
|
|
|
|
|
|
static struct spi_driver gehc_achc_spi_driver = {
|
|
|
|
.driver = {
|
|
|
|
.name = "gehc-achc",
|
|
|
|
.of_match_table = gehc_achc_of_match,
|
|
|
|
.dev_groups = gehc_achc_groups,
|
|
|
|
},
|
|
|
|
.probe = gehc_achc_probe,
|
|
|
|
.id_table = gehc_achc_id,
|
|
|
|
};
|
|
|
|
module_spi_driver(gehc_achc_spi_driver);
|
|
|
|
|
|
|
|
MODULE_DESCRIPTION("GEHC ACHC driver");
|
|
|
|
MODULE_AUTHOR("Sebastian Reichel <sebastian.reichel@collabora.com>");
|
|
|
|
MODULE_LICENSE("GPL");
|