OpenCloudOS-Kernel/drivers/net/r8169.c

2950 lines
74 KiB
C
Raw Normal View History

/*
=========================================================================
r8169.c: A RealTek RTL-8169 Gigabit Ethernet driver for Linux kernel 2.4.x.
--------------------------------------------------------------------
History:
Feb 4 2002 - created initially by ShuChen <shuchen@realtek.com.tw>.
May 20 2002 - Add link status force-mode and TBI mode support.
2004 - Massive updates. See kernel SCM system for details.
=========================================================================
1. [DEPRECATED: use ethtool instead] The media can be forced in 5 modes.
Command: 'insmod r8169 media = SET_MEDIA'
Ex: 'insmod r8169 media = 0x04' will force PHY to operate in 100Mpbs Half-duplex.
SET_MEDIA can be:
_10_Half = 0x01
_10_Full = 0x02
_100_Half = 0x04
_100_Full = 0x08
_1000_Full = 0x10
2. Support TBI mode.
=========================================================================
VERSION 1.1 <2002/10/4>
The bit4:0 of MII register 4 is called "selector field", and have to be
00001b to indicate support of IEEE std 802.3 during NWay process of
exchanging Link Code Word (FLP).
VERSION 1.2 <2002/11/30>
- Large style cleanup
- Use ether_crc in stock kernel (linux/crc32.h)
- Copy mc_filter setup code from 8139cp
(includes an optimization, and avoids set_bit use)
VERSION 1.6LK <2004/04/14>
- Merge of Realtek's version 1.6
- Conversion to DMA API
- Suspend/resume
- Endianness
- Misc Rx/Tx bugs
VERSION 2.2LK <2005/01/25>
- RX csum, TX csum/SG, TSO
- VLAN
- baby (< 7200) Jumbo frames support
- Merge of Realtek's version 2.2 (new phy)
*/
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/pci.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/delay.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
#include <linux/if_vlan.h>
#include <linux/crc32.h>
#include <linux/in.h>
#include <linux/ip.h>
#include <linux/tcp.h>
#include <linux/init.h>
#include <linux/dma-mapping.h>
#include <asm/io.h>
#include <asm/irq.h>
#ifdef CONFIG_R8169_NAPI
#define NAPI_SUFFIX "-NAPI"
#else
#define NAPI_SUFFIX ""
#endif
#define RTL8169_VERSION "2.2LK" NAPI_SUFFIX
#define MODULENAME "r8169"
#define PFX MODULENAME ": "
#ifdef RTL8169_DEBUG
#define assert(expr) \
if (!(expr)) { \
printk( "Assertion failed! %s,%s,%s,line=%d\n", \
#expr,__FILE__,__FUNCTION__,__LINE__); \
}
#define dprintk(fmt, args...) do { printk(PFX fmt, ## args); } while (0)
#else
#define assert(expr) do {} while (0)
#define dprintk(fmt, args...) do {} while (0)
#endif /* RTL8169_DEBUG */
#define R8169_MSG_DEFAULT \
(NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN)
#define TX_BUFFS_AVAIL(tp) \
(tp->dirty_tx + NUM_TX_DESC - tp->cur_tx - 1)
#ifdef CONFIG_R8169_NAPI
#define rtl8169_rx_skb netif_receive_skb
#define rtl8169_rx_hwaccel_skb vlan_hwaccel_receive_skb
#define rtl8169_rx_quota(count, quota) min(count, quota)
#else
#define rtl8169_rx_skb netif_rx
#define rtl8169_rx_hwaccel_skb vlan_hwaccel_rx
#define rtl8169_rx_quota(count, quota) count
#endif
/* media options */
#define MAX_UNITS 8
static int media[MAX_UNITS] = { -1, -1, -1, -1, -1, -1, -1, -1 };
static int num_media = 0;
/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
2006-03-04 10:33:57 +08:00
static const int max_interrupt_work = 20;
/* Maximum number of multicast addresses to filter (vs. Rx-all-multicast).
The RTL chips use a 64 element hash table based on the Ethernet CRC. */
2006-03-04 10:33:57 +08:00
static const int multicast_filter_limit = 32;
/* MAC address length */
#define MAC_ADDR_LEN 6
#define RX_FIFO_THRESH 7 /* 7 means NO threshold, Rx buffer level before first PCI xfer. */
#define RX_DMA_BURST 6 /* Maximum PCI burst, '6' is 1024 */
#define TX_DMA_BURST 6 /* Maximum PCI burst, '6' is 1024 */
#define EarlyTxThld 0x3F /* 0x3F means NO early transmit */
#define RxPacketMaxSize 0x3FE8 /* 16K - 1 - ETH_HLEN - VLAN - CRC... */
#define SafeMtu 0x1c20 /* ... actually life sucks beyond ~7k */
#define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */
#define R8169_REGS_SIZE 256
#define R8169_NAPI_WEIGHT 64
#define NUM_TX_DESC 64 /* Number of Tx descriptor registers */
#define NUM_RX_DESC 256 /* Number of Rx descriptor registers */
#define RX_BUF_SIZE 1536 /* Rx Buffer size */
#define R8169_TX_RING_BYTES (NUM_TX_DESC * sizeof(struct TxDesc))
#define R8169_RX_RING_BYTES (NUM_RX_DESC * sizeof(struct RxDesc))
#define RTL8169_TX_TIMEOUT (6*HZ)
#define RTL8169_PHY_TIMEOUT (10*HZ)
/* write/read MMIO register */
#define RTL_W8(reg, val8) writeb ((val8), ioaddr + (reg))
#define RTL_W16(reg, val16) writew ((val16), ioaddr + (reg))
#define RTL_W32(reg, val32) writel ((val32), ioaddr + (reg))
#define RTL_R8(reg) readb (ioaddr + (reg))
#define RTL_R16(reg) readw (ioaddr + (reg))
#define RTL_R32(reg) ((unsigned long) readl (ioaddr + (reg)))
enum mac_version {
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
RTL_GIGA_MAC_VER_01 = 0x00,
RTL_GIGA_MAC_VER_02 = 0x01,
RTL_GIGA_MAC_VER_03 = 0x02,
RTL_GIGA_MAC_VER_04 = 0x03,
RTL_GIGA_MAC_VER_05 = 0x04,
RTL_GIGA_MAC_VER_11 = 0x0b,
RTL_GIGA_MAC_VER_12 = 0x0c,
RTL_GIGA_MAC_VER_13 = 0x0d,
RTL_GIGA_MAC_VER_14 = 0x0e,
RTL_GIGA_MAC_VER_15 = 0x0f
};
enum phy_version {
RTL_GIGA_PHY_VER_C = 0x03, /* PHY Reg 0x03 bit0-3 == 0x0000 */
RTL_GIGA_PHY_VER_D = 0x04, /* PHY Reg 0x03 bit0-3 == 0x0000 */
RTL_GIGA_PHY_VER_E = 0x05, /* PHY Reg 0x03 bit0-3 == 0x0000 */
RTL_GIGA_PHY_VER_F = 0x06, /* PHY Reg 0x03 bit0-3 == 0x0001 */
RTL_GIGA_PHY_VER_G = 0x07, /* PHY Reg 0x03 bit0-3 == 0x0002 */
RTL_GIGA_PHY_VER_H = 0x08, /* PHY Reg 0x03 bit0-3 == 0x0003 */
};
#define _R(NAME,MAC,MASK) \
{ .name = NAME, .mac_version = MAC, .RxConfigMask = MASK }
static const struct {
const char *name;
u8 mac_version;
u32 RxConfigMask; /* Clears the bits supported by this chip */
} rtl_chip_info[] = {
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
_R("RTL8169", RTL_GIGA_MAC_VER_01, 0xff7e1880),
_R("RTL8169s/8110s", RTL_GIGA_MAC_VER_02, 0xff7e1880),
_R("RTL8169s/8110s", RTL_GIGA_MAC_VER_03, 0xff7e1880),
_R("RTL8169sb/8110sb", RTL_GIGA_MAC_VER_04, 0xff7e1880),
_R("RTL8169sc/8110sc", RTL_GIGA_MAC_VER_05, 0xff7e1880),
_R("RTL8168b/8111b", RTL_GIGA_MAC_VER_11, 0xff7e1880), // PCI-E
_R("RTL8168b/8111b", RTL_GIGA_MAC_VER_12, 0xff7e1880), // PCI-E
_R("RTL8101e", RTL_GIGA_MAC_VER_13, 0xff7e1880), // PCI-E 8139
_R("RTL8100e", RTL_GIGA_MAC_VER_14, 0xff7e1880), // PCI-E 8139
_R("RTL8100e", RTL_GIGA_MAC_VER_15, 0xff7e1880) // PCI-E 8139
};
#undef _R
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
enum cfg_version {
RTL_CFG_0 = 0x00,
RTL_CFG_1,
RTL_CFG_2
};
static const struct {
unsigned int region;
unsigned int align;
} rtl_cfg_info[] = {
[RTL_CFG_0] = { 1, NET_IP_ALIGN },
[RTL_CFG_1] = { 2, NET_IP_ALIGN },
[RTL_CFG_2] = { 2, 8 }
};
static struct pci_device_id rtl8169_pci_tbl[] = {
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8129), 0, 0, RTL_CFG_0 },
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8136), 0, 0, RTL_CFG_2 },
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8167), 0, 0, RTL_CFG_0 },
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8168), 0, 0, RTL_CFG_2 },
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8169), 0, 0, RTL_CFG_0 },
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4300), 0, 0, RTL_CFG_0 },
{ PCI_DEVICE(0x1259, 0xc107), 0, 0, RTL_CFG_0 },
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
{ PCI_DEVICE(0x16ec, 0x0116), 0, 0, RTL_CFG_0 },
{ PCI_VENDOR_ID_LINKSYS, 0x1032,
PCI_ANY_ID, 0x0024, 0, 0, RTL_CFG_0 },
{0,},
};
MODULE_DEVICE_TABLE(pci, rtl8169_pci_tbl);
static int rx_copybreak = 200;
static int use_dac;
static int ignore_parity_err;
static struct {
u32 msg_enable;
} debug = { -1 };
enum RTL8169_registers {
MAC0 = 0, /* Ethernet hardware address. */
MAR0 = 8, /* Multicast filter. */
CounterAddrLow = 0x10,
CounterAddrHigh = 0x14,
TxDescStartAddrLow = 0x20,
TxDescStartAddrHigh = 0x24,
TxHDescStartAddrLow = 0x28,
TxHDescStartAddrHigh = 0x2c,
FLASH = 0x30,
ERSR = 0x36,
ChipCmd = 0x37,
TxPoll = 0x38,
IntrMask = 0x3C,
IntrStatus = 0x3E,
TxConfig = 0x40,
RxConfig = 0x44,
RxMissed = 0x4C,
Cfg9346 = 0x50,
Config0 = 0x51,
Config1 = 0x52,
Config2 = 0x53,
Config3 = 0x54,
Config4 = 0x55,
Config5 = 0x56,
MultiIntr = 0x5C,
PHYAR = 0x60,
TBICSR = 0x64,
TBI_ANAR = 0x68,
TBI_LPAR = 0x6A,
PHYstatus = 0x6C,
RxMaxSize = 0xDA,
CPlusCmd = 0xE0,
IntrMitigate = 0xE2,
RxDescAddrLow = 0xE4,
RxDescAddrHigh = 0xE8,
EarlyTxThres = 0xEC,
FuncEvent = 0xF0,
FuncEventMask = 0xF4,
FuncPresetState = 0xF8,
FuncForceEvent = 0xFC,
};
enum RTL8169_register_content {
/* InterruptStatusBits */
SYSErr = 0x8000,
PCSTimeout = 0x4000,
SWInt = 0x0100,
TxDescUnavail = 0x80,
RxFIFOOver = 0x40,
LinkChg = 0x20,
RxOverflow = 0x10,
TxErr = 0x08,
TxOK = 0x04,
RxErr = 0x02,
RxOK = 0x01,
/* RxStatusDesc */
RxFOVF = (1 << 23),
RxRWT = (1 << 22),
RxRES = (1 << 21),
RxRUNT = (1 << 20),
RxCRC = (1 << 19),
/* ChipCmdBits */
CmdReset = 0x10,
CmdRxEnb = 0x08,
CmdTxEnb = 0x04,
RxBufEmpty = 0x01,
/* Cfg9346Bits */
Cfg9346_Lock = 0x00,
Cfg9346_Unlock = 0xC0,
/* rx_mode_bits */
AcceptErr = 0x20,
AcceptRunt = 0x10,
AcceptBroadcast = 0x08,
AcceptMulticast = 0x04,
AcceptMyPhys = 0x02,
AcceptAllPhys = 0x01,
/* RxConfigBits */
RxCfgFIFOShift = 13,
RxCfgDMAShift = 8,
/* TxConfigBits */
TxInterFrameGapShift = 24,
TxDMAShift = 8, /* DMA burst value (0-7) is shift this many bits */
/* Config1 register p.24 */
PMEnable = (1 << 0), /* Power Management Enable */
/* Config3 register p.25 */
MagicPacket = (1 << 5), /* Wake up when receives a Magic Packet */
LinkUp = (1 << 4), /* Wake up when the cable connection is re-established */
/* Config5 register p.27 */
BWF = (1 << 6), /* Accept Broadcast wakeup frame */
MWF = (1 << 5), /* Accept Multicast wakeup frame */
UWF = (1 << 4), /* Accept Unicast wakeup frame */
LanWake = (1 << 1), /* LanWake enable/disable */
PMEStatus = (1 << 0), /* PME status can be reset by PCI RST# */
/* TBICSR p.28 */
TBIReset = 0x80000000,
TBILoopback = 0x40000000,
TBINwEnable = 0x20000000,
TBINwRestart = 0x10000000,
TBILinkOk = 0x02000000,
TBINwComplete = 0x01000000,
/* CPlusCmd p.31 */
RxVlan = (1 << 6),
RxChkSum = (1 << 5),
PCIDAC = (1 << 4),
PCIMulRW = (1 << 3),
/* rtl8169_PHYstatus */
TBI_Enable = 0x80,
TxFlowCtrl = 0x40,
RxFlowCtrl = 0x20,
_1000bpsF = 0x10,
_100bps = 0x08,
_10bps = 0x04,
LinkStatus = 0x02,
FullDup = 0x01,
/* _MediaType */
_10_Half = 0x01,
_10_Full = 0x02,
_100_Half = 0x04,
_100_Full = 0x08,
_1000_Full = 0x10,
/* _TBICSRBit */
TBILinkOK = 0x02000000,
/* DumpCounterCommand */
CounterDump = 0x8,
};
enum _DescStatusBit {
DescOwn = (1 << 31), /* Descriptor is owned by NIC */
RingEnd = (1 << 30), /* End of descriptor ring */
FirstFrag = (1 << 29), /* First segment of a packet */
LastFrag = (1 << 28), /* Final segment of a packet */
/* Tx private */
LargeSend = (1 << 27), /* TCP Large Send Offload (TSO) */
MSSShift = 16, /* MSS value position */
MSSMask = 0xfff, /* MSS value + LargeSend bit: 12 bits */
IPCS = (1 << 18), /* Calculate IP checksum */
UDPCS = (1 << 17), /* Calculate UDP/IP checksum */
TCPCS = (1 << 16), /* Calculate TCP/IP checksum */
TxVlanTag = (1 << 17), /* Add VLAN tag */
/* Rx private */
PID1 = (1 << 18), /* Protocol ID bit 1/2 */
PID0 = (1 << 17), /* Protocol ID bit 2/2 */
#define RxProtoUDP (PID1)
#define RxProtoTCP (PID0)
#define RxProtoIP (PID1 | PID0)
#define RxProtoMask RxProtoIP
IPFail = (1 << 16), /* IP checksum failed */
UDPFail = (1 << 15), /* UDP/IP checksum failed */
TCPFail = (1 << 14), /* TCP/IP checksum failed */
RxVlanTag = (1 << 16), /* VLAN tag available */
};
#define RsvdMask 0x3fffc000
struct TxDesc {
u32 opts1;
u32 opts2;
u64 addr;
};
struct RxDesc {
u32 opts1;
u32 opts2;
u64 addr;
};
struct ring_info {
struct sk_buff *skb;
u32 len;
u8 __pad[sizeof(void *) - sizeof(u32)];
};
struct rtl8169_private {
void __iomem *mmio_addr; /* memory map physical address */
struct pci_dev *pci_dev; /* Index of PCI device */
struct net_device *dev;
struct net_device_stats stats; /* statistics of net device */
spinlock_t lock; /* spin lock flag */
u32 msg_enable;
int chipset;
int mac_version;
int phy_version;
u32 cur_rx; /* Index into the Rx descriptor buffer of next Rx pkt. */
u32 cur_tx; /* Index into the Tx descriptor buffer of next Rx pkt. */
u32 dirty_rx;
u32 dirty_tx;
struct TxDesc *TxDescArray; /* 256-aligned Tx descriptor ring */
struct RxDesc *RxDescArray; /* 256-aligned Rx descriptor ring */
dma_addr_t TxPhyAddr;
dma_addr_t RxPhyAddr;
struct sk_buff *Rx_skbuff[NUM_RX_DESC]; /* Rx data buffers */
struct ring_info tx_skb[NUM_TX_DESC]; /* Tx data buffers */
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
unsigned align;
unsigned rx_buf_sz;
struct timer_list timer;
u16 cp_cmd;
u16 intr_mask;
int phy_auto_nego_reg;
int phy_1000_ctrl_reg;
#ifdef CONFIG_R8169_VLAN
struct vlan_group *vlgrp;
#endif
int (*set_speed)(struct net_device *, u8 autoneg, u16 speed, u8 duplex);
void (*get_settings)(struct net_device *, struct ethtool_cmd *);
void (*phy_reset_enable)(void __iomem *);
unsigned int (*phy_reset_pending)(void __iomem *);
unsigned int (*link_ok)(void __iomem *);
struct delayed_work task;
unsigned wol_enabled : 1;
};
MODULE_AUTHOR("Realtek and the Linux r8169 crew <netdev@vger.kernel.org>");
MODULE_DESCRIPTION("RealTek RTL-8169 Gigabit Ethernet driver");
module_param_array(media, int, &num_media, 0);
MODULE_PARM_DESC(media, "force phy operation. Deprecated by ethtool (8).");
module_param(rx_copybreak, int, 0);
MODULE_PARM_DESC(rx_copybreak, "Copy breakpoint for copy-only-tiny-frames");
module_param(use_dac, int, 0);
MODULE_PARM_DESC(use_dac, "Enable PCI DAC. Unsafe on 32 bit PCI slot.");
module_param_named(debug, debug.msg_enable, int, 0);
MODULE_PARM_DESC(debug, "Debug verbosity level (0=none, ..., 16=all)");
module_param_named(ignore_parity_err, ignore_parity_err, bool, 0);
MODULE_PARM_DESC(ignore_parity_err, "Ignore PCI parity error as target. Default: false");
MODULE_LICENSE("GPL");
MODULE_VERSION(RTL8169_VERSION);
static int rtl8169_open(struct net_device *dev);
static int rtl8169_start_xmit(struct sk_buff *skb, struct net_device *dev);
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 21:55:46 +08:00
static irqreturn_t rtl8169_interrupt(int irq, void *dev_instance);
static int rtl8169_init_ring(struct net_device *dev);
static void rtl8169_hw_start(struct net_device *dev);
static int rtl8169_close(struct net_device *dev);
static void rtl8169_set_rx_mode(struct net_device *dev);
static void rtl8169_tx_timeout(struct net_device *dev);
static struct net_device_stats *rtl8169_get_stats(struct net_device *dev);
static int rtl8169_rx_interrupt(struct net_device *, struct rtl8169_private *,
void __iomem *);
static int rtl8169_change_mtu(struct net_device *dev, int new_mtu);
static void rtl8169_down(struct net_device *dev);
#ifdef CONFIG_R8169_NAPI
static int rtl8169_poll(struct net_device *dev, int *budget);
#endif
static const u16 rtl8169_intr_mask =
SYSErr | LinkChg | RxOverflow | RxFIFOOver | TxErr | TxOK | RxErr | RxOK;
static const u16 rtl8169_napi_event =
RxOK | RxOverflow | RxFIFOOver | TxOK | TxErr;
static const unsigned int rtl8169_rx_config =
(RX_FIFO_THRESH << RxCfgFIFOShift) | (RX_DMA_BURST << RxCfgDMAShift);
static void mdio_write(void __iomem *ioaddr, int RegAddr, int value)
{
int i;
RTL_W32(PHYAR, 0x80000000 | (RegAddr & 0xFF) << 16 | value);
for (i = 20; i > 0; i--) {
/* Check if the RTL8169 has completed writing to the specified MII register */
if (!(RTL_R32(PHYAR) & 0x80000000))
break;
udelay(25);
}
}
static int mdio_read(void __iomem *ioaddr, int RegAddr)
{
int i, value = -1;
RTL_W32(PHYAR, 0x0 | (RegAddr & 0xFF) << 16);
for (i = 20; i > 0; i--) {
/* Check if the RTL8169 has completed retrieving data from the specified MII register */
if (RTL_R32(PHYAR) & 0x80000000) {
value = (int) (RTL_R32(PHYAR) & 0xFFFF);
break;
}
udelay(25);
}
return value;
}
static void rtl8169_irq_mask_and_ack(void __iomem *ioaddr)
{
RTL_W16(IntrMask, 0x0000);
RTL_W16(IntrStatus, 0xffff);
}
static void rtl8169_asic_down(void __iomem *ioaddr)
{
RTL_W8(ChipCmd, 0x00);
rtl8169_irq_mask_and_ack(ioaddr);
RTL_R16(CPlusCmd);
}
static unsigned int rtl8169_tbi_reset_pending(void __iomem *ioaddr)
{
return RTL_R32(TBICSR) & TBIReset;
}
static unsigned int rtl8169_xmii_reset_pending(void __iomem *ioaddr)
{
return mdio_read(ioaddr, MII_BMCR) & BMCR_RESET;
}
static unsigned int rtl8169_tbi_link_ok(void __iomem *ioaddr)
{
return RTL_R32(TBICSR) & TBILinkOk;
}
static unsigned int rtl8169_xmii_link_ok(void __iomem *ioaddr)
{
return RTL_R8(PHYstatus) & LinkStatus;
}
static void rtl8169_tbi_reset_enable(void __iomem *ioaddr)
{
RTL_W32(TBICSR, RTL_R32(TBICSR) | TBIReset);
}
static void rtl8169_xmii_reset_enable(void __iomem *ioaddr)
{
unsigned int val;
mdio_write(ioaddr, MII_BMCR, BMCR_RESET);
val = mdio_read(ioaddr, MII_BMCR);
}
static void rtl8169_check_link_status(struct net_device *dev,
struct rtl8169_private *tp, void __iomem *ioaddr)
{
unsigned long flags;
spin_lock_irqsave(&tp->lock, flags);
if (tp->link_ok(ioaddr)) {
netif_carrier_on(dev);
if (netif_msg_ifup(tp))
printk(KERN_INFO PFX "%s: link up\n", dev->name);
} else {
if (netif_msg_ifdown(tp))
printk(KERN_INFO PFX "%s: link down\n", dev->name);
netif_carrier_off(dev);
}
spin_unlock_irqrestore(&tp->lock, flags);
}
static void rtl8169_link_option(int idx, u8 *autoneg, u16 *speed, u8 *duplex)
{
struct {
u16 speed;
u8 duplex;
u8 autoneg;
u8 media;
} link_settings[] = {
{ SPEED_10, DUPLEX_HALF, AUTONEG_DISABLE, _10_Half },
{ SPEED_10, DUPLEX_FULL, AUTONEG_DISABLE, _10_Full },
{ SPEED_100, DUPLEX_HALF, AUTONEG_DISABLE, _100_Half },
{ SPEED_100, DUPLEX_FULL, AUTONEG_DISABLE, _100_Full },
{ SPEED_1000, DUPLEX_FULL, AUTONEG_DISABLE, _1000_Full },
/* Make TBI happy */
{ SPEED_1000, DUPLEX_FULL, AUTONEG_ENABLE, 0xff }
}, *p;
unsigned char option;
option = ((idx < MAX_UNITS) && (idx >= 0)) ? media[idx] : 0xff;
if ((option != 0xff) && !idx && netif_msg_drv(&debug))
printk(KERN_WARNING PFX "media option is deprecated.\n");
for (p = link_settings; p->media != 0xff; p++) {
if (p->media == option)
break;
}
*autoneg = p->autoneg;
*speed = p->speed;
*duplex = p->duplex;
}
static void rtl8169_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
u8 options;
wol->wolopts = 0;
#define WAKE_ANY (WAKE_PHY | WAKE_MAGIC | WAKE_UCAST | WAKE_BCAST | WAKE_MCAST)
wol->supported = WAKE_ANY;
spin_lock_irq(&tp->lock);
options = RTL_R8(Config1);
if (!(options & PMEnable))
goto out_unlock;
options = RTL_R8(Config3);
if (options & LinkUp)
wol->wolopts |= WAKE_PHY;
if (options & MagicPacket)
wol->wolopts |= WAKE_MAGIC;
options = RTL_R8(Config5);
if (options & UWF)
wol->wolopts |= WAKE_UCAST;
if (options & BWF)
wol->wolopts |= WAKE_BCAST;
if (options & MWF)
wol->wolopts |= WAKE_MCAST;
out_unlock:
spin_unlock_irq(&tp->lock);
}
static int rtl8169_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
int i;
static struct {
u32 opt;
u16 reg;
u8 mask;
} cfg[] = {
{ WAKE_ANY, Config1, PMEnable },
{ WAKE_PHY, Config3, LinkUp },
{ WAKE_MAGIC, Config3, MagicPacket },
{ WAKE_UCAST, Config5, UWF },
{ WAKE_BCAST, Config5, BWF },
{ WAKE_MCAST, Config5, MWF },
{ WAKE_ANY, Config5, LanWake }
};
spin_lock_irq(&tp->lock);
RTL_W8(Cfg9346, Cfg9346_Unlock);
for (i = 0; i < ARRAY_SIZE(cfg); i++) {
u8 options = RTL_R8(cfg[i].reg) & ~cfg[i].mask;
if (wol->wolopts & cfg[i].opt)
options |= cfg[i].mask;
RTL_W8(cfg[i].reg, options);
}
RTL_W8(Cfg9346, Cfg9346_Lock);
tp->wol_enabled = (wol->wolopts) ? 1 : 0;
spin_unlock_irq(&tp->lock);
return 0;
}
static void rtl8169_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
struct rtl8169_private *tp = netdev_priv(dev);
strcpy(info->driver, MODULENAME);
strcpy(info->version, RTL8169_VERSION);
strcpy(info->bus_info, pci_name(tp->pci_dev));
}
static int rtl8169_get_regs_len(struct net_device *dev)
{
return R8169_REGS_SIZE;
}
static int rtl8169_set_speed_tbi(struct net_device *dev,
u8 autoneg, u16 speed, u8 duplex)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
int ret = 0;
u32 reg;
reg = RTL_R32(TBICSR);
if ((autoneg == AUTONEG_DISABLE) && (speed == SPEED_1000) &&
(duplex == DUPLEX_FULL)) {
RTL_W32(TBICSR, reg & ~(TBINwEnable | TBINwRestart));
} else if (autoneg == AUTONEG_ENABLE)
RTL_W32(TBICSR, reg | TBINwEnable | TBINwRestart);
else {
if (netif_msg_link(tp)) {
printk(KERN_WARNING "%s: "
"incorrect speed setting refused in TBI mode\n",
dev->name);
}
ret = -EOPNOTSUPP;
}
return ret;
}
static int rtl8169_set_speed_xmii(struct net_device *dev,
u8 autoneg, u16 speed, u8 duplex)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
int auto_nego, giga_ctrl;
auto_nego = mdio_read(ioaddr, MII_ADVERTISE);
auto_nego &= ~(ADVERTISE_10HALF | ADVERTISE_10FULL |
ADVERTISE_100HALF | ADVERTISE_100FULL);
giga_ctrl = mdio_read(ioaddr, MII_CTRL1000);
giga_ctrl &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
if (autoneg == AUTONEG_ENABLE) {
auto_nego |= (ADVERTISE_10HALF | ADVERTISE_10FULL |
ADVERTISE_100HALF | ADVERTISE_100FULL);
giga_ctrl |= ADVERTISE_1000FULL | ADVERTISE_1000HALF;
} else {
if (speed == SPEED_10)
auto_nego |= ADVERTISE_10HALF | ADVERTISE_10FULL;
else if (speed == SPEED_100)
auto_nego |= ADVERTISE_100HALF | ADVERTISE_100FULL;
else if (speed == SPEED_1000)
giga_ctrl |= ADVERTISE_1000FULL | ADVERTISE_1000HALF;
if (duplex == DUPLEX_HALF)
auto_nego &= ~(ADVERTISE_10FULL | ADVERTISE_100FULL);
if (duplex == DUPLEX_FULL)
auto_nego &= ~(ADVERTISE_10HALF | ADVERTISE_100HALF);
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
/* This tweak comes straight from Realtek's driver. */
if ((speed == SPEED_100) && (duplex == DUPLEX_HALF) &&
(tp->mac_version == RTL_GIGA_MAC_VER_13)) {
auto_nego = ADVERTISE_100HALF | ADVERTISE_CSMA;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
}
}
/* The 8100e/8101e do Fast Ethernet only. */
if ((tp->mac_version == RTL_GIGA_MAC_VER_13) ||
(tp->mac_version == RTL_GIGA_MAC_VER_14) ||
(tp->mac_version == RTL_GIGA_MAC_VER_15)) {
if ((giga_ctrl & (ADVERTISE_1000FULL | ADVERTISE_1000HALF)) &&
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
netif_msg_link(tp)) {
printk(KERN_INFO "%s: PHY does not support 1000Mbps.\n",
dev->name);
}
giga_ctrl &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
}
auto_nego |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM;
tp->phy_auto_nego_reg = auto_nego;
tp->phy_1000_ctrl_reg = giga_ctrl;
mdio_write(ioaddr, MII_ADVERTISE, auto_nego);
mdio_write(ioaddr, MII_CTRL1000, giga_ctrl);
mdio_write(ioaddr, MII_BMCR, BMCR_ANENABLE | BMCR_ANRESTART);
return 0;
}
static int rtl8169_set_speed(struct net_device *dev,
u8 autoneg, u16 speed, u8 duplex)
{
struct rtl8169_private *tp = netdev_priv(dev);
int ret;
ret = tp->set_speed(dev, autoneg, speed, duplex);
if (netif_running(dev) && (tp->phy_1000_ctrl_reg & ADVERTISE_1000FULL))
mod_timer(&tp->timer, jiffies + RTL8169_PHY_TIMEOUT);
return ret;
}
static int rtl8169_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct rtl8169_private *tp = netdev_priv(dev);
unsigned long flags;
int ret;
spin_lock_irqsave(&tp->lock, flags);
ret = rtl8169_set_speed(dev, cmd->autoneg, cmd->speed, cmd->duplex);
spin_unlock_irqrestore(&tp->lock, flags);
return ret;
}
static u32 rtl8169_get_rx_csum(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
return tp->cp_cmd & RxChkSum;
}
static int rtl8169_set_rx_csum(struct net_device *dev, u32 data)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
unsigned long flags;
spin_lock_irqsave(&tp->lock, flags);
if (data)
tp->cp_cmd |= RxChkSum;
else
tp->cp_cmd &= ~RxChkSum;
RTL_W16(CPlusCmd, tp->cp_cmd);
RTL_R16(CPlusCmd);
spin_unlock_irqrestore(&tp->lock, flags);
return 0;
}
#ifdef CONFIG_R8169_VLAN
static inline u32 rtl8169_tx_vlan_tag(struct rtl8169_private *tp,
struct sk_buff *skb)
{
return (tp->vlgrp && vlan_tx_tag_present(skb)) ?
TxVlanTag | swab16(vlan_tx_tag_get(skb)) : 0x00;
}
static void rtl8169_vlan_rx_register(struct net_device *dev,
struct vlan_group *grp)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
unsigned long flags;
spin_lock_irqsave(&tp->lock, flags);
tp->vlgrp = grp;
if (tp->vlgrp)
tp->cp_cmd |= RxVlan;
else
tp->cp_cmd &= ~RxVlan;
RTL_W16(CPlusCmd, tp->cp_cmd);
RTL_R16(CPlusCmd);
spin_unlock_irqrestore(&tp->lock, flags);
}
static void rtl8169_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
{
struct rtl8169_private *tp = netdev_priv(dev);
unsigned long flags;
spin_lock_irqsave(&tp->lock, flags);
if (tp->vlgrp)
tp->vlgrp->vlan_devices[vid] = NULL;
spin_unlock_irqrestore(&tp->lock, flags);
}
static int rtl8169_rx_vlan_skb(struct rtl8169_private *tp, struct RxDesc *desc,
struct sk_buff *skb)
{
u32 opts2 = le32_to_cpu(desc->opts2);
int ret;
if (tp->vlgrp && (opts2 & RxVlanTag)) {
rtl8169_rx_hwaccel_skb(skb, tp->vlgrp,
swab16(opts2 & 0xffff));
ret = 0;
} else
ret = -1;
desc->opts2 = 0;
return ret;
}
#else /* !CONFIG_R8169_VLAN */
static inline u32 rtl8169_tx_vlan_tag(struct rtl8169_private *tp,
struct sk_buff *skb)
{
return 0;
}
static int rtl8169_rx_vlan_skb(struct rtl8169_private *tp, struct RxDesc *desc,
struct sk_buff *skb)
{
return -1;
}
#endif
static void rtl8169_gset_tbi(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
u32 status;
cmd->supported =
SUPPORTED_1000baseT_Full | SUPPORTED_Autoneg | SUPPORTED_FIBRE;
cmd->port = PORT_FIBRE;
cmd->transceiver = XCVR_INTERNAL;
status = RTL_R32(TBICSR);
cmd->advertising = (status & TBINwEnable) ? ADVERTISED_Autoneg : 0;
cmd->autoneg = !!(status & TBINwEnable);
cmd->speed = SPEED_1000;
cmd->duplex = DUPLEX_FULL; /* Always set */
}
static void rtl8169_gset_xmii(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
u8 status;
cmd->supported = SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Full |
SUPPORTED_Autoneg |
SUPPORTED_TP;
cmd->autoneg = 1;
cmd->advertising = ADVERTISED_TP | ADVERTISED_Autoneg;
if (tp->phy_auto_nego_reg & ADVERTISE_10HALF)
cmd->advertising |= ADVERTISED_10baseT_Half;
if (tp->phy_auto_nego_reg & ADVERTISE_10FULL)
cmd->advertising |= ADVERTISED_10baseT_Full;
if (tp->phy_auto_nego_reg & ADVERTISE_100HALF)
cmd->advertising |= ADVERTISED_100baseT_Half;
if (tp->phy_auto_nego_reg & ADVERTISE_100FULL)
cmd->advertising |= ADVERTISED_100baseT_Full;
if (tp->phy_1000_ctrl_reg & ADVERTISE_1000FULL)
cmd->advertising |= ADVERTISED_1000baseT_Full;
status = RTL_R8(PHYstatus);
if (status & _1000bpsF)
cmd->speed = SPEED_1000;
else if (status & _100bps)
cmd->speed = SPEED_100;
else if (status & _10bps)
cmd->speed = SPEED_10;
if (status & TxFlowCtrl)
cmd->advertising |= ADVERTISED_Asym_Pause;
if (status & RxFlowCtrl)
cmd->advertising |= ADVERTISED_Pause;
cmd->duplex = ((status & _1000bpsF) || (status & FullDup)) ?
DUPLEX_FULL : DUPLEX_HALF;
}
static int rtl8169_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct rtl8169_private *tp = netdev_priv(dev);
unsigned long flags;
spin_lock_irqsave(&tp->lock, flags);
tp->get_settings(dev, cmd);
spin_unlock_irqrestore(&tp->lock, flags);
return 0;
}
static void rtl8169_get_regs(struct net_device *dev, struct ethtool_regs *regs,
void *p)
{
struct rtl8169_private *tp = netdev_priv(dev);
unsigned long flags;
if (regs->len > R8169_REGS_SIZE)
regs->len = R8169_REGS_SIZE;
spin_lock_irqsave(&tp->lock, flags);
memcpy_fromio(p, tp->mmio_addr, regs->len);
spin_unlock_irqrestore(&tp->lock, flags);
}
static u32 rtl8169_get_msglevel(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
return tp->msg_enable;
}
static void rtl8169_set_msglevel(struct net_device *dev, u32 value)
{
struct rtl8169_private *tp = netdev_priv(dev);
tp->msg_enable = value;
}
static const char rtl8169_gstrings[][ETH_GSTRING_LEN] = {
"tx_packets",
"rx_packets",
"tx_errors",
"rx_errors",
"rx_missed",
"align_errors",
"tx_single_collisions",
"tx_multi_collisions",
"unicast",
"broadcast",
"multicast",
"tx_aborted",
"tx_underrun",
};
struct rtl8169_counters {
u64 tx_packets;
u64 rx_packets;
u64 tx_errors;
u32 rx_errors;
u16 rx_missed;
u16 align_errors;
u32 tx_one_collision;
u32 tx_multi_collision;
u64 rx_unicast;
u64 rx_broadcast;
u32 rx_multicast;
u16 tx_aborted;
u16 tx_underun;
};
static int rtl8169_get_stats_count(struct net_device *dev)
{
return ARRAY_SIZE(rtl8169_gstrings);
}
static void rtl8169_get_ethtool_stats(struct net_device *dev,
struct ethtool_stats *stats, u64 *data)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
struct rtl8169_counters *counters;
dma_addr_t paddr;
u32 cmd;
ASSERT_RTNL();
counters = pci_alloc_consistent(tp->pci_dev, sizeof(*counters), &paddr);
if (!counters)
return;
RTL_W32(CounterAddrHigh, (u64)paddr >> 32);
cmd = (u64)paddr & DMA_32BIT_MASK;
RTL_W32(CounterAddrLow, cmd);
RTL_W32(CounterAddrLow, cmd | CounterDump);
while (RTL_R32(CounterAddrLow) & CounterDump) {
if (msleep_interruptible(1))
break;
}
RTL_W32(CounterAddrLow, 0);
RTL_W32(CounterAddrHigh, 0);
data[0] = le64_to_cpu(counters->tx_packets);
data[1] = le64_to_cpu(counters->rx_packets);
data[2] = le64_to_cpu(counters->tx_errors);
data[3] = le32_to_cpu(counters->rx_errors);
data[4] = le16_to_cpu(counters->rx_missed);
data[5] = le16_to_cpu(counters->align_errors);
data[6] = le32_to_cpu(counters->tx_one_collision);
data[7] = le32_to_cpu(counters->tx_multi_collision);
data[8] = le64_to_cpu(counters->rx_unicast);
data[9] = le64_to_cpu(counters->rx_broadcast);
data[10] = le32_to_cpu(counters->rx_multicast);
data[11] = le16_to_cpu(counters->tx_aborted);
data[12] = le16_to_cpu(counters->tx_underun);
pci_free_consistent(tp->pci_dev, sizeof(*counters), counters, paddr);
}
static void rtl8169_get_strings(struct net_device *dev, u32 stringset, u8 *data)
{
switch(stringset) {
case ETH_SS_STATS:
memcpy(data, *rtl8169_gstrings, sizeof(rtl8169_gstrings));
break;
}
}
static const struct ethtool_ops rtl8169_ethtool_ops = {
.get_drvinfo = rtl8169_get_drvinfo,
.get_regs_len = rtl8169_get_regs_len,
.get_link = ethtool_op_get_link,
.get_settings = rtl8169_get_settings,
.set_settings = rtl8169_set_settings,
.get_msglevel = rtl8169_get_msglevel,
.set_msglevel = rtl8169_set_msglevel,
.get_rx_csum = rtl8169_get_rx_csum,
.set_rx_csum = rtl8169_set_rx_csum,
.get_tx_csum = ethtool_op_get_tx_csum,
.set_tx_csum = ethtool_op_set_tx_csum,
.get_sg = ethtool_op_get_sg,
.set_sg = ethtool_op_set_sg,
.get_tso = ethtool_op_get_tso,
.set_tso = ethtool_op_set_tso,
.get_regs = rtl8169_get_regs,
.get_wol = rtl8169_get_wol,
.set_wol = rtl8169_set_wol,
.get_strings = rtl8169_get_strings,
.get_stats_count = rtl8169_get_stats_count,
.get_ethtool_stats = rtl8169_get_ethtool_stats,
.get_perm_addr = ethtool_op_get_perm_addr,
};
static void rtl8169_write_gmii_reg_bit(void __iomem *ioaddr, int reg, int bitnum,
int bitval)
{
int val;
val = mdio_read(ioaddr, reg);
val = (bitval == 1) ?
val | (bitval << bitnum) : val & ~(0x0001 << bitnum);
mdio_write(ioaddr, reg, val & 0xffff);
}
static void rtl8169_get_mac_version(struct rtl8169_private *tp, void __iomem *ioaddr)
{
const struct {
u32 mask;
int mac_version;
} mac_info[] = {
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
{ 0x38800000, RTL_GIGA_MAC_VER_15 },
{ 0x38000000, RTL_GIGA_MAC_VER_12 },
{ 0x34000000, RTL_GIGA_MAC_VER_13 },
{ 0x30800000, RTL_GIGA_MAC_VER_14 },
{ 0x30000000, RTL_GIGA_MAC_VER_11 },
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
{ 0x18000000, RTL_GIGA_MAC_VER_05 },
{ 0x10000000, RTL_GIGA_MAC_VER_04 },
{ 0x04000000, RTL_GIGA_MAC_VER_03 },
{ 0x00800000, RTL_GIGA_MAC_VER_02 },
{ 0x00000000, RTL_GIGA_MAC_VER_01 } /* Catch-all */
}, *p = mac_info;
u32 reg;
reg = RTL_R32(TxConfig) & 0x7c800000;
while ((reg & p->mask) != p->mask)
p++;
tp->mac_version = p->mac_version;
}
static void rtl8169_print_mac_version(struct rtl8169_private *tp)
{
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
dprintk("mac_version = 0x%02x\n", tp->mac_version);
}
static void rtl8169_get_phy_version(struct rtl8169_private *tp, void __iomem *ioaddr)
{
const struct {
u16 mask;
u16 set;
int phy_version;
} phy_info[] = {
{ 0x000f, 0x0002, RTL_GIGA_PHY_VER_G },
{ 0x000f, 0x0001, RTL_GIGA_PHY_VER_F },
{ 0x000f, 0x0000, RTL_GIGA_PHY_VER_E },
{ 0x0000, 0x0000, RTL_GIGA_PHY_VER_D } /* Catch-all */
}, *p = phy_info;
u16 reg;
reg = mdio_read(ioaddr, MII_PHYSID2) & 0xffff;
while ((reg & p->mask) != p->set)
p++;
tp->phy_version = p->phy_version;
}
static void rtl8169_print_phy_version(struct rtl8169_private *tp)
{
struct {
int version;
char *msg;
u32 reg;
} phy_print[] = {
{ RTL_GIGA_PHY_VER_G, "RTL_GIGA_PHY_VER_G", 0x0002 },
{ RTL_GIGA_PHY_VER_F, "RTL_GIGA_PHY_VER_F", 0x0001 },
{ RTL_GIGA_PHY_VER_E, "RTL_GIGA_PHY_VER_E", 0x0000 },
{ RTL_GIGA_PHY_VER_D, "RTL_GIGA_PHY_VER_D", 0x0000 },
{ 0, NULL, 0x0000 }
}, *p;
for (p = phy_print; p->msg; p++) {
if (tp->phy_version == p->version) {
dprintk("phy_version == %s (%04x)\n", p->msg, p->reg);
return;
}
}
dprintk("phy_version == Unknown\n");
}
static void rtl8169_hw_phy_config(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
struct {
u16 regs[5]; /* Beware of bit-sign propagation */
} phy_magic[5] = { {
{ 0x0000, //w 4 15 12 0
0x00a1, //w 3 15 0 00a1
0x0008, //w 2 15 0 0008
0x1020, //w 1 15 0 1020
0x1000 } },{ //w 0 15 0 1000
{ 0x7000, //w 4 15 12 7
0xff41, //w 3 15 0 ff41
0xde60, //w 2 15 0 de60
0x0140, //w 1 15 0 0140
0x0077 } },{ //w 0 15 0 0077
{ 0xa000, //w 4 15 12 a
0xdf01, //w 3 15 0 df01
0xdf20, //w 2 15 0 df20
0xff95, //w 1 15 0 ff95
0xfa00 } },{ //w 0 15 0 fa00
{ 0xb000, //w 4 15 12 b
0xff41, //w 3 15 0 ff41
0xde20, //w 2 15 0 de20
0x0140, //w 1 15 0 0140
0x00bb } },{ //w 0 15 0 00bb
{ 0xf000, //w 4 15 12 f
0xdf01, //w 3 15 0 df01
0xdf20, //w 2 15 0 df20
0xff95, //w 1 15 0 ff95
0xbf00 } //w 0 15 0 bf00
}
}, *p = phy_magic;
int i;
rtl8169_print_mac_version(tp);
rtl8169_print_phy_version(tp);
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if (tp->mac_version <= RTL_GIGA_MAC_VER_01)
return;
if (tp->phy_version >= RTL_GIGA_PHY_VER_H)
return;
dprintk("MAC version != 0 && PHY version == 0 or 1\n");
dprintk("Do final_reg2.cfg\n");
/* Shazam ! */
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if (tp->mac_version == RTL_GIGA_MAC_VER_04) {
mdio_write(ioaddr, 31, 0x0002);
mdio_write(ioaddr, 1, 0x90d0);
mdio_write(ioaddr, 31, 0x0000);
return;
}
/* phy config for RTL8169s mac_version C chip */
mdio_write(ioaddr, 31, 0x0001); //w 31 2 0 1
mdio_write(ioaddr, 21, 0x1000); //w 21 15 0 1000
mdio_write(ioaddr, 24, 0x65c7); //w 24 15 0 65c7
rtl8169_write_gmii_reg_bit(ioaddr, 4, 11, 0); //w 4 11 11 0
for (i = 0; i < ARRAY_SIZE(phy_magic); i++, p++) {
int val, pos = 4;
val = (mdio_read(ioaddr, pos) & 0x0fff) | (p->regs[0] & 0xffff);
mdio_write(ioaddr, pos, val);
while (--pos >= 0)
mdio_write(ioaddr, pos, p->regs[4 - pos] & 0xffff);
rtl8169_write_gmii_reg_bit(ioaddr, 4, 11, 1); //w 4 11 11 1
rtl8169_write_gmii_reg_bit(ioaddr, 4, 11, 0); //w 4 11 11 0
}
mdio_write(ioaddr, 31, 0x0000); //w 31 2 0 0
}
static void rtl8169_phy_timer(unsigned long __opaque)
{
struct net_device *dev = (struct net_device *)__opaque;
struct rtl8169_private *tp = netdev_priv(dev);
struct timer_list *timer = &tp->timer;
void __iomem *ioaddr = tp->mmio_addr;
unsigned long timeout = RTL8169_PHY_TIMEOUT;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
assert(tp->mac_version > RTL_GIGA_MAC_VER_01);
assert(tp->phy_version < RTL_GIGA_PHY_VER_H);
if (!(tp->phy_1000_ctrl_reg & ADVERTISE_1000FULL))
return;
spin_lock_irq(&tp->lock);
if (tp->phy_reset_pending(ioaddr)) {
/*
* A busy loop could burn quite a few cycles on nowadays CPU.
* Let's delay the execution of the timer for a few ticks.
*/
timeout = HZ/10;
goto out_mod_timer;
}
if (tp->link_ok(ioaddr))
goto out_unlock;
if (netif_msg_link(tp))
printk(KERN_WARNING "%s: PHY reset until link up\n", dev->name);
tp->phy_reset_enable(ioaddr);
out_mod_timer:
mod_timer(timer, jiffies + timeout);
out_unlock:
spin_unlock_irq(&tp->lock);
}
static inline void rtl8169_delete_timer(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
struct timer_list *timer = &tp->timer;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if ((tp->mac_version <= RTL_GIGA_MAC_VER_01) ||
(tp->phy_version >= RTL_GIGA_PHY_VER_H))
return;
del_timer_sync(timer);
}
static inline void rtl8169_request_timer(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
struct timer_list *timer = &tp->timer;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if ((tp->mac_version <= RTL_GIGA_MAC_VER_01) ||
(tp->phy_version >= RTL_GIGA_PHY_VER_H))
return;
init_timer(timer);
timer->expires = jiffies + RTL8169_PHY_TIMEOUT;
timer->data = (unsigned long)(dev);
timer->function = rtl8169_phy_timer;
add_timer(timer);
}
#ifdef CONFIG_NET_POLL_CONTROLLER
/*
* Polling 'interrupt' - used by things like netconsole to send skbs
* without having to re-enable interrupts. It's not called while
* the interrupt routine is executing.
*/
static void rtl8169_netpoll(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
struct pci_dev *pdev = tp->pci_dev;
disable_irq(pdev->irq);
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 21:55:46 +08:00
rtl8169_interrupt(pdev->irq, dev);
enable_irq(pdev->irq);
}
#endif
static void rtl8169_release_board(struct pci_dev *pdev, struct net_device *dev,
void __iomem *ioaddr)
{
iounmap(ioaddr);
pci_release_regions(pdev);
pci_disable_device(pdev);
free_netdev(dev);
}
static void rtl8169_phy_reset(struct net_device *dev,
struct rtl8169_private *tp)
{
void __iomem *ioaddr = tp->mmio_addr;
int i;
tp->phy_reset_enable(ioaddr);
for (i = 0; i < 100; i++) {
if (!tp->phy_reset_pending(ioaddr))
return;
msleep(1);
}
if (netif_msg_link(tp))
printk(KERN_ERR "%s: PHY reset failed.\n", dev->name);
}
static void rtl8169_init_phy(struct net_device *dev, struct rtl8169_private *tp)
{
void __iomem *ioaddr = tp->mmio_addr;
static int board_idx = -1;
u8 autoneg, duplex;
u16 speed;
board_idx++;
rtl8169_hw_phy_config(dev);
dprintk("Set MAC Reg C+CR Offset 0x82h = 0x01h\n");
RTL_W8(0x82, 0x01);
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if (tp->mac_version < RTL_GIGA_MAC_VER_03) {
dprintk("Set PCI Latency=0x40\n");
pci_write_config_byte(tp->pci_dev, PCI_LATENCY_TIMER, 0x40);
}
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if (tp->mac_version == RTL_GIGA_MAC_VER_02) {
dprintk("Set MAC Reg C+CR Offset 0x82h = 0x01h\n");
RTL_W8(0x82, 0x01);
dprintk("Set PHY Reg 0x0bh = 0x00h\n");
mdio_write(ioaddr, 0x0b, 0x0000); //w 0x0b 15 0 0
}
rtl8169_link_option(board_idx, &autoneg, &speed, &duplex);
rtl8169_phy_reset(dev, tp);
rtl8169_set_speed(dev, autoneg, speed, duplex);
if ((RTL_R8(PHYstatus) & TBI_Enable) && netif_msg_link(tp))
printk(KERN_INFO PFX "%s: TBI auto-negotiating\n", dev->name);
}
static int rtl8169_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
{
struct rtl8169_private *tp = netdev_priv(dev);
struct mii_ioctl_data *data = if_mii(ifr);
if (!netif_running(dev))
return -ENODEV;
switch (cmd) {
case SIOCGMIIPHY:
data->phy_id = 32; /* Internal PHY */
return 0;
case SIOCGMIIREG:
data->val_out = mdio_read(tp->mmio_addr, data->reg_num & 0x1f);
return 0;
case SIOCSMIIREG:
if (!capable(CAP_NET_ADMIN))
return -EPERM;
mdio_write(tp->mmio_addr, data->reg_num & 0x1f, data->val_in);
return 0;
}
return -EOPNOTSUPP;
}
static int __devinit
rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
const unsigned int region = rtl_cfg_info[ent->driver_data].region;
struct rtl8169_private *tp;
struct net_device *dev;
void __iomem *ioaddr;
unsigned int pm_cap;
int i, rc;
if (netif_msg_drv(&debug)) {
printk(KERN_INFO "%s Gigabit Ethernet driver %s loaded\n",
MODULENAME, RTL8169_VERSION);
}
dev = alloc_etherdev(sizeof (*tp));
if (!dev) {
if (netif_msg_drv(&debug))
dev_err(&pdev->dev, "unable to alloc new ethernet\n");
rc = -ENOMEM;
goto out;
}
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
tp = netdev_priv(dev);
tp->dev = dev;
tp->msg_enable = netif_msg_init(debug.msg_enable, R8169_MSG_DEFAULT);
/* enable device (incl. PCI PM wakeup and hotplug setup) */
rc = pci_enable_device(pdev);
if (rc < 0) {
if (netif_msg_probe(tp))
dev_err(&pdev->dev, "enable failure\n");
goto err_out_free_dev_1;
}
rc = pci_set_mwi(pdev);
if (rc < 0)
goto err_out_disable_2;
/* save power state before pci_enable_device overwrites it */
pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
if (pm_cap) {
u16 pwr_command, acpi_idle_state;
pci_read_config_word(pdev, pm_cap + PCI_PM_CTRL, &pwr_command);
acpi_idle_state = pwr_command & PCI_PM_CTRL_STATE_MASK;
} else {
if (netif_msg_probe(tp)) {
dev_err(&pdev->dev,
"PowerManagement capability not found.\n");
}
}
/* make sure PCI base addr 1 is MMIO */
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if (!(pci_resource_flags(pdev, region) & IORESOURCE_MEM)) {
if (netif_msg_probe(tp)) {
dev_err(&pdev->dev,
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
"region #%d not an MMIO resource, aborting\n",
region);
}
rc = -ENODEV;
goto err_out_mwi_3;
}
/* check for weird/broken PCI region reporting */
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if (pci_resource_len(pdev, region) < R8169_REGS_SIZE) {
if (netif_msg_probe(tp)) {
dev_err(&pdev->dev,
"Invalid PCI region size(s), aborting\n");
}
rc = -ENODEV;
goto err_out_mwi_3;
}
rc = pci_request_regions(pdev, MODULENAME);
if (rc < 0) {
if (netif_msg_probe(tp))
dev_err(&pdev->dev, "could not request regions.\n");
goto err_out_mwi_3;
}
tp->cp_cmd = PCIMulRW | RxChkSum;
if ((sizeof(dma_addr_t) > 4) &&
!pci_set_dma_mask(pdev, DMA_64BIT_MASK) && use_dac) {
tp->cp_cmd |= PCIDAC;
dev->features |= NETIF_F_HIGHDMA;
} else {
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc < 0) {
if (netif_msg_probe(tp)) {
dev_err(&pdev->dev,
"DMA configuration failed.\n");
}
goto err_out_free_res_4;
}
}
pci_set_master(pdev);
/* ioremap MMIO region */
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
ioaddr = ioremap(pci_resource_start(pdev, region), R8169_REGS_SIZE);
if (!ioaddr) {
if (netif_msg_probe(tp))
dev_err(&pdev->dev, "cannot remap MMIO, aborting\n");
rc = -EIO;
goto err_out_free_res_4;
}
/* Unneeded ? Don't mess with Mrs. Murphy. */
rtl8169_irq_mask_and_ack(ioaddr);
/* Soft reset the chip. */
RTL_W8(ChipCmd, CmdReset);
/* Check that the chip has finished the reset. */
for (i = 100; i > 0; i--) {
if ((RTL_R8(ChipCmd) & CmdReset) == 0)
break;
msleep_interruptible(1);
}
/* Identify chip attached to board */
rtl8169_get_mac_version(tp, ioaddr);
rtl8169_get_phy_version(tp, ioaddr);
rtl8169_print_mac_version(tp);
rtl8169_print_phy_version(tp);
for (i = ARRAY_SIZE(rtl_chip_info) - 1; i >= 0; i--) {
if (tp->mac_version == rtl_chip_info[i].mac_version)
break;
}
if (i < 0) {
/* Unknown chip: assume array element #0, original RTL-8169 */
if (netif_msg_probe(tp)) {
dev_printk(KERN_DEBUG, &pdev->dev,
"unknown chip version, assuming %s\n",
rtl_chip_info[0].name);
}
i++;
}
tp->chipset = i;
RTL_W8(Cfg9346, Cfg9346_Unlock);
RTL_W8(Config1, RTL_R8(Config1) | PMEnable);
RTL_W8(Config5, RTL_R8(Config5) & PMEStatus);
RTL_W8(Cfg9346, Cfg9346_Lock);
if (RTL_R8(PHYstatus) & TBI_Enable) {
tp->set_speed = rtl8169_set_speed_tbi;
tp->get_settings = rtl8169_gset_tbi;
tp->phy_reset_enable = rtl8169_tbi_reset_enable;
tp->phy_reset_pending = rtl8169_tbi_reset_pending;
tp->link_ok = rtl8169_tbi_link_ok;
tp->phy_1000_ctrl_reg = ADVERTISE_1000FULL; /* Implied by TBI */
} else {
tp->set_speed = rtl8169_set_speed_xmii;
tp->get_settings = rtl8169_gset_xmii;
tp->phy_reset_enable = rtl8169_xmii_reset_enable;
tp->phy_reset_pending = rtl8169_xmii_reset_pending;
tp->link_ok = rtl8169_xmii_link_ok;
dev->do_ioctl = rtl8169_ioctl;
}
/* Get MAC address. FIXME: read EEPROM */
for (i = 0; i < MAC_ADDR_LEN; i++)
dev->dev_addr[i] = RTL_R8(MAC0 + i);
memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
dev->open = rtl8169_open;
dev->hard_start_xmit = rtl8169_start_xmit;
dev->get_stats = rtl8169_get_stats;
SET_ETHTOOL_OPS(dev, &rtl8169_ethtool_ops);
dev->stop = rtl8169_close;
dev->tx_timeout = rtl8169_tx_timeout;
dev->set_multicast_list = rtl8169_set_rx_mode;
dev->watchdog_timeo = RTL8169_TX_TIMEOUT;
dev->irq = pdev->irq;
dev->base_addr = (unsigned long) ioaddr;
dev->change_mtu = rtl8169_change_mtu;
#ifdef CONFIG_R8169_NAPI
dev->poll = rtl8169_poll;
dev->weight = R8169_NAPI_WEIGHT;
#endif
#ifdef CONFIG_R8169_VLAN
dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
dev->vlan_rx_register = rtl8169_vlan_rx_register;
dev->vlan_rx_kill_vid = rtl8169_vlan_rx_kill_vid;
#endif
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = rtl8169_netpoll;
#endif
tp->intr_mask = 0xffff;
tp->pci_dev = pdev;
tp->mmio_addr = ioaddr;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
tp->align = rtl_cfg_info[ent->driver_data].align;
spin_lock_init(&tp->lock);
rc = register_netdev(dev);
if (rc < 0)
goto err_out_unmap_5;
pci_set_drvdata(pdev, dev);
if (netif_msg_probe(tp)) {
printk(KERN_INFO "%s: %s at 0x%lx, "
"%2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x, "
"IRQ %d\n",
dev->name,
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
rtl_chip_info[tp->chipset].name,
dev->base_addr,
dev->dev_addr[0], dev->dev_addr[1],
dev->dev_addr[2], dev->dev_addr[3],
dev->dev_addr[4], dev->dev_addr[5], dev->irq);
}
rtl8169_init_phy(dev, tp);
out:
return rc;
err_out_unmap_5:
iounmap(ioaddr);
err_out_free_res_4:
pci_release_regions(pdev);
err_out_mwi_3:
pci_clear_mwi(pdev);
err_out_disable_2:
pci_disable_device(pdev);
err_out_free_dev_1:
free_netdev(dev);
goto out;
}
static void __devexit
rtl8169_remove_one(struct pci_dev *pdev)
{
struct net_device *dev = pci_get_drvdata(pdev);
struct rtl8169_private *tp = netdev_priv(dev);
assert(dev != NULL);
assert(tp != NULL);
unregister_netdev(dev);
rtl8169_release_board(pdev, dev, tp->mmio_addr);
pci_set_drvdata(pdev, NULL);
}
static void rtl8169_set_rxbufsize(struct rtl8169_private *tp,
struct net_device *dev)
{
unsigned int mtu = dev->mtu;
tp->rx_buf_sz = (mtu > RX_BUF_SIZE) ? mtu + ETH_HLEN + 8 : RX_BUF_SIZE;
}
static int rtl8169_open(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
struct pci_dev *pdev = tp->pci_dev;
int retval;
rtl8169_set_rxbufsize(tp, dev);
retval =
request_irq(dev->irq, rtl8169_interrupt, IRQF_SHARED, dev->name, dev);
if (retval < 0)
goto out;
retval = -ENOMEM;
/*
* Rx and Tx desscriptors needs 256 bytes alignment.
* pci_alloc_consistent provides more.
*/
tp->TxDescArray = pci_alloc_consistent(pdev, R8169_TX_RING_BYTES,
&tp->TxPhyAddr);
if (!tp->TxDescArray)
goto err_free_irq;
tp->RxDescArray = pci_alloc_consistent(pdev, R8169_RX_RING_BYTES,
&tp->RxPhyAddr);
if (!tp->RxDescArray)
goto err_free_tx;
retval = rtl8169_init_ring(dev);
if (retval < 0)
goto err_free_rx;
INIT_DELAYED_WORK(&tp->task, NULL);
rtl8169_hw_start(dev);
rtl8169_request_timer(dev);
rtl8169_check_link_status(dev, tp, tp->mmio_addr);
out:
return retval;
err_free_rx:
pci_free_consistent(pdev, R8169_RX_RING_BYTES, tp->RxDescArray,
tp->RxPhyAddr);
err_free_tx:
pci_free_consistent(pdev, R8169_TX_RING_BYTES, tp->TxDescArray,
tp->TxPhyAddr);
err_free_irq:
free_irq(dev->irq, dev);
goto out;
}
static void rtl8169_hw_reset(void __iomem *ioaddr)
{
/* Disable interrupts */
rtl8169_irq_mask_and_ack(ioaddr);
/* Reset the chipset */
RTL_W8(ChipCmd, CmdReset);
/* PCI commit */
RTL_R8(ChipCmd);
}
static void rtl8169_set_rx_tx_config_registers(struct rtl8169_private *tp)
{
void __iomem *ioaddr = tp->mmio_addr;
u32 cfg = rtl8169_rx_config;
cfg |= (RTL_R32(RxConfig) & rtl_chip_info[tp->chipset].RxConfigMask);
RTL_W32(RxConfig, cfg);
/* Set DMA burst size and Interframe Gap Time */
RTL_W32(TxConfig, (TX_DMA_BURST << TxDMAShift) |
(InterFrameGap << TxInterFrameGapShift));
}
static void rtl8169_hw_start(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
struct pci_dev *pdev = tp->pci_dev;
u16 cmd;
u32 i;
/* Soft reset the chip. */
RTL_W8(ChipCmd, CmdReset);
/* Check that the chip has finished the reset. */
for (i = 100; i > 0; i--) {
if ((RTL_R8(ChipCmd) & CmdReset) == 0)
break;
msleep_interruptible(1);
}
if (tp->mac_version == RTL_GIGA_MAC_VER_05) {
RTL_W16(CPlusCmd, RTL_R16(CPlusCmd) | PCIMulRW);
pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x08);
}
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if (tp->mac_version == RTL_GIGA_MAC_VER_13) {
pci_write_config_word(pdev, 0x68, 0x00);
pci_write_config_word(pdev, 0x69, 0x08);
}
/* Undocumented stuff. */
if (tp->mac_version == RTL_GIGA_MAC_VER_05) {
/* Realtek's r1000_n.c driver uses '&& 0x01' here. Well... */
if ((RTL_R8(Config2) & 0x07) & 0x01)
RTL_W32(0x7c, 0x0007ffff);
RTL_W32(0x7c, 0x0007ff00);
pci_read_config_word(pdev, PCI_COMMAND, &cmd);
cmd = cmd & 0xef;
pci_write_config_word(pdev, PCI_COMMAND, cmd);
}
RTL_W8(Cfg9346, Cfg9346_Unlock);
if ((tp->mac_version == RTL_GIGA_MAC_VER_01) ||
(tp->mac_version == RTL_GIGA_MAC_VER_02) ||
(tp->mac_version == RTL_GIGA_MAC_VER_03) ||
(tp->mac_version == RTL_GIGA_MAC_VER_04))
RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
RTL_W8(EarlyTxThres, EarlyTxThld);
/* Low hurts. Let's disable the filtering. */
RTL_W16(RxMaxSize, 16383);
if ((tp->mac_version == RTL_GIGA_MAC_VER_01) ||
(tp->mac_version == RTL_GIGA_MAC_VER_02) ||
(tp->mac_version == RTL_GIGA_MAC_VER_03) ||
(tp->mac_version == RTL_GIGA_MAC_VER_04))
RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
rtl8169_set_rx_tx_config_registers(tp);
cmd = RTL_R16(CPlusCmd);
RTL_W16(CPlusCmd, cmd);
tp->cp_cmd |= cmd | PCIMulRW;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if ((tp->mac_version == RTL_GIGA_MAC_VER_02) ||
(tp->mac_version == RTL_GIGA_MAC_VER_03)) {
dprintk(KERN_INFO PFX "Set MAC Reg C+CR Offset 0xE0. "
"Bit-3 and bit-14 MUST be 1\n");
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
tp->cp_cmd |= (1 << 14);
}
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
RTL_W16(CPlusCmd, tp->cp_cmd);
/*
* Undocumented corner. Supposedly:
* (TxTimer << 12) | (TxPackets << 8) | (RxTimer << 4) | RxPackets
*/
RTL_W16(IntrMitigate, 0x0000);
/*
* Magic spell: some iop3xx ARM board needs the TxDescAddrHigh
* register to be written before TxDescAddrLow to work.
* Switching from MMIO to I/O access fixes the issue as well.
*/
RTL_W32(TxDescStartAddrHigh, ((u64) tp->TxPhyAddr >> 32));
RTL_W32(TxDescStartAddrLow, ((u64) tp->TxPhyAddr & DMA_32BIT_MASK));
RTL_W32(RxDescAddrHigh, ((u64) tp->RxPhyAddr >> 32));
RTL_W32(RxDescAddrLow, ((u64) tp->RxPhyAddr & DMA_32BIT_MASK));
if ((tp->mac_version != RTL_GIGA_MAC_VER_01) &&
(tp->mac_version != RTL_GIGA_MAC_VER_02) &&
(tp->mac_version != RTL_GIGA_MAC_VER_03) &&
(tp->mac_version != RTL_GIGA_MAC_VER_04)) {
RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
rtl8169_set_rx_tx_config_registers(tp);
}
RTL_W8(Cfg9346, Cfg9346_Lock);
/* Initially a 10 us delay. Turned it into a PCI commit. - FR */
RTL_R8(IntrMask);
RTL_W32(RxMissed, 0);
rtl8169_set_rx_mode(dev);
/* no early-rx interrupts */
RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xF000);
/* Enable all known interrupts by setting the interrupt mask. */
RTL_W16(IntrMask, rtl8169_intr_mask);
netif_start_queue(dev);
}
static int rtl8169_change_mtu(struct net_device *dev, int new_mtu)
{
struct rtl8169_private *tp = netdev_priv(dev);
int ret = 0;
if (new_mtu < ETH_ZLEN || new_mtu > SafeMtu)
return -EINVAL;
dev->mtu = new_mtu;
if (!netif_running(dev))
goto out;
rtl8169_down(dev);
rtl8169_set_rxbufsize(tp, dev);
ret = rtl8169_init_ring(dev);
if (ret < 0)
goto out;
netif_poll_enable(dev);
rtl8169_hw_start(dev);
rtl8169_request_timer(dev);
out:
return ret;
}
static inline void rtl8169_make_unusable_by_asic(struct RxDesc *desc)
{
desc->addr = 0x0badbadbadbadbadull;
desc->opts1 &= ~cpu_to_le32(DescOwn | RsvdMask);
}
static void rtl8169_free_rx_skb(struct rtl8169_private *tp,
struct sk_buff **sk_buff, struct RxDesc *desc)
{
struct pci_dev *pdev = tp->pci_dev;
pci_unmap_single(pdev, le64_to_cpu(desc->addr), tp->rx_buf_sz,
PCI_DMA_FROMDEVICE);
dev_kfree_skb(*sk_buff);
*sk_buff = NULL;
rtl8169_make_unusable_by_asic(desc);
}
static inline void rtl8169_mark_to_asic(struct RxDesc *desc, u32 rx_buf_sz)
{
u32 eor = le32_to_cpu(desc->opts1) & RingEnd;
desc->opts1 = cpu_to_le32(DescOwn | eor | rx_buf_sz);
}
static inline void rtl8169_map_to_asic(struct RxDesc *desc, dma_addr_t mapping,
u32 rx_buf_sz)
{
desc->addr = cpu_to_le64(mapping);
wmb();
rtl8169_mark_to_asic(desc, rx_buf_sz);
}
static int rtl8169_alloc_rx_skb(struct pci_dev *pdev, struct sk_buff **sk_buff,
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
struct RxDesc *desc, int rx_buf_sz,
unsigned int align)
{
struct sk_buff *skb;
dma_addr_t mapping;
int ret = 0;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
skb = dev_alloc_skb(rx_buf_sz + align);
if (!skb)
goto err_out;
skb_reserve(skb, (align - 1) & (u32)skb->data);
*sk_buff = skb;
mapping = pci_map_single(pdev, skb->data, rx_buf_sz,
PCI_DMA_FROMDEVICE);
rtl8169_map_to_asic(desc, mapping, rx_buf_sz);
out:
return ret;
err_out:
ret = -ENOMEM;
rtl8169_make_unusable_by_asic(desc);
goto out;
}
static void rtl8169_rx_clear(struct rtl8169_private *tp)
{
int i;
for (i = 0; i < NUM_RX_DESC; i++) {
if (tp->Rx_skbuff[i]) {
rtl8169_free_rx_skb(tp, tp->Rx_skbuff + i,
tp->RxDescArray + i);
}
}
}
static u32 rtl8169_rx_fill(struct rtl8169_private *tp, struct net_device *dev,
u32 start, u32 end)
{
u32 cur;
for (cur = start; end - cur > 0; cur++) {
int ret, i = cur % NUM_RX_DESC;
if (tp->Rx_skbuff[i])
continue;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
ret = rtl8169_alloc_rx_skb(tp->pci_dev, tp->Rx_skbuff + i,
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
tp->RxDescArray + i, tp->rx_buf_sz, tp->align);
if (ret < 0)
break;
}
return cur - start;
}
static inline void rtl8169_mark_as_last_descriptor(struct RxDesc *desc)
{
desc->opts1 |= cpu_to_le32(RingEnd);
}
static void rtl8169_init_ring_indexes(struct rtl8169_private *tp)
{
tp->dirty_tx = tp->dirty_rx = tp->cur_tx = tp->cur_rx = 0;
}
static int rtl8169_init_ring(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
rtl8169_init_ring_indexes(tp);
memset(tp->tx_skb, 0x0, NUM_TX_DESC * sizeof(struct ring_info));
memset(tp->Rx_skbuff, 0x0, NUM_RX_DESC * sizeof(struct sk_buff *));
if (rtl8169_rx_fill(tp, dev, 0, NUM_RX_DESC) != NUM_RX_DESC)
goto err_out;
rtl8169_mark_as_last_descriptor(tp->RxDescArray + NUM_RX_DESC - 1);
return 0;
err_out:
rtl8169_rx_clear(tp);
return -ENOMEM;
}
static void rtl8169_unmap_tx_skb(struct pci_dev *pdev, struct ring_info *tx_skb,
struct TxDesc *desc)
{
unsigned int len = tx_skb->len;
pci_unmap_single(pdev, le64_to_cpu(desc->addr), len, PCI_DMA_TODEVICE);
desc->opts1 = 0x00;
desc->opts2 = 0x00;
desc->addr = 0x00;
tx_skb->len = 0;
}
static void rtl8169_tx_clear(struct rtl8169_private *tp)
{
unsigned int i;
for (i = tp->dirty_tx; i < tp->dirty_tx + NUM_TX_DESC; i++) {
unsigned int entry = i % NUM_TX_DESC;
struct ring_info *tx_skb = tp->tx_skb + entry;
unsigned int len = tx_skb->len;
if (len) {
struct sk_buff *skb = tx_skb->skb;
rtl8169_unmap_tx_skb(tp->pci_dev, tx_skb,
tp->TxDescArray + entry);
if (skb) {
dev_kfree_skb(skb);
tx_skb->skb = NULL;
}
tp->stats.tx_dropped++;
}
}
tp->cur_tx = tp->dirty_tx = 0;
}
static void rtl8169_schedule_work(struct net_device *dev, work_func_t task)
{
struct rtl8169_private *tp = netdev_priv(dev);
PREPARE_DELAYED_WORK(&tp->task, task);
schedule_delayed_work(&tp->task, 4);
}
static void rtl8169_wait_for_quiescence(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
synchronize_irq(dev->irq);
/* Wait for any pending NAPI task to complete */
netif_poll_disable(dev);
rtl8169_irq_mask_and_ack(ioaddr);
netif_poll_enable(dev);
}
static void rtl8169_reinit_task(struct work_struct *work)
{
struct rtl8169_private *tp =
container_of(work, struct rtl8169_private, task.work);
struct net_device *dev = tp->dev;
int ret;
if (netif_running(dev)) {
rtl8169_wait_for_quiescence(dev);
rtl8169_close(dev);
}
ret = rtl8169_open(dev);
if (unlikely(ret < 0)) {
if (net_ratelimit()) {
struct rtl8169_private *tp = netdev_priv(dev);
if (netif_msg_drv(tp)) {
printk(PFX KERN_ERR
"%s: reinit failure (status = %d)."
" Rescheduling.\n", dev->name, ret);
}
}
rtl8169_schedule_work(dev, rtl8169_reinit_task);
}
}
static void rtl8169_reset_task(struct work_struct *work)
{
struct rtl8169_private *tp =
container_of(work, struct rtl8169_private, task.work);
struct net_device *dev = tp->dev;
if (!netif_running(dev))
return;
rtl8169_wait_for_quiescence(dev);
rtl8169_rx_interrupt(dev, tp, tp->mmio_addr);
rtl8169_tx_clear(tp);
if (tp->dirty_rx == tp->cur_rx) {
rtl8169_init_ring_indexes(tp);
rtl8169_hw_start(dev);
netif_wake_queue(dev);
} else {
if (net_ratelimit()) {
struct rtl8169_private *tp = netdev_priv(dev);
if (netif_msg_intr(tp)) {
printk(PFX KERN_EMERG
"%s: Rx buffers shortage\n", dev->name);
}
}
rtl8169_schedule_work(dev, rtl8169_reset_task);
}
}
static void rtl8169_tx_timeout(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
rtl8169_hw_reset(tp->mmio_addr);
/* Let's wait a bit while any (async) irq lands on */
rtl8169_schedule_work(dev, rtl8169_reset_task);
}
static int rtl8169_xmit_frags(struct rtl8169_private *tp, struct sk_buff *skb,
u32 opts1)
{
struct skb_shared_info *info = skb_shinfo(skb);
unsigned int cur_frag, entry;
struct TxDesc *txd;
entry = tp->cur_tx;
for (cur_frag = 0; cur_frag < info->nr_frags; cur_frag++) {
skb_frag_t *frag = info->frags + cur_frag;
dma_addr_t mapping;
u32 status, len;
void *addr;
entry = (entry + 1) % NUM_TX_DESC;
txd = tp->TxDescArray + entry;
len = frag->size;
addr = ((void *) page_address(frag->page)) + frag->page_offset;
mapping = pci_map_single(tp->pci_dev, addr, len, PCI_DMA_TODEVICE);
/* anti gcc 2.95.3 bugware (sic) */
status = opts1 | len | (RingEnd * !((entry + 1) % NUM_TX_DESC));
txd->opts1 = cpu_to_le32(status);
txd->addr = cpu_to_le64(mapping);
tp->tx_skb[entry].len = len;
}
if (cur_frag) {
tp->tx_skb[entry].skb = skb;
txd->opts1 |= cpu_to_le32(LastFrag);
}
return cur_frag;
}
static inline u32 rtl8169_tso_csum(struct sk_buff *skb, struct net_device *dev)
{
if (dev->features & NETIF_F_TSO) {
u32 mss = skb_shinfo(skb)->gso_size;
if (mss)
return LargeSend | ((mss & MSSMask) << MSSShift);
}
if (skb->ip_summed == CHECKSUM_PARTIAL) {
const struct iphdr *ip = skb->nh.iph;
if (ip->protocol == IPPROTO_TCP)
return IPCS | TCPCS;
else if (ip->protocol == IPPROTO_UDP)
return IPCS | UDPCS;
WARN_ON(1); /* we need a WARN() */
}
return 0;
}
static int rtl8169_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
unsigned int frags, entry = tp->cur_tx % NUM_TX_DESC;
struct TxDesc *txd = tp->TxDescArray + entry;
void __iomem *ioaddr = tp->mmio_addr;
dma_addr_t mapping;
u32 status, len;
u32 opts1;
int ret = NETDEV_TX_OK;
if (unlikely(TX_BUFFS_AVAIL(tp) < skb_shinfo(skb)->nr_frags)) {
if (netif_msg_drv(tp)) {
printk(KERN_ERR
"%s: BUG! Tx Ring full when queue awake!\n",
dev->name);
}
goto err_stop;
}
if (unlikely(le32_to_cpu(txd->opts1) & DescOwn))
goto err_stop;
opts1 = DescOwn | rtl8169_tso_csum(skb, dev);
frags = rtl8169_xmit_frags(tp, skb, opts1);
if (frags) {
len = skb_headlen(skb);
opts1 |= FirstFrag;
} else {
len = skb->len;
if (unlikely(len < ETH_ZLEN)) {
if (skb_padto(skb, ETH_ZLEN))
goto err_update_stats;
len = ETH_ZLEN;
}
opts1 |= FirstFrag | LastFrag;
tp->tx_skb[entry].skb = skb;
}
mapping = pci_map_single(tp->pci_dev, skb->data, len, PCI_DMA_TODEVICE);
tp->tx_skb[entry].len = len;
txd->addr = cpu_to_le64(mapping);
txd->opts2 = cpu_to_le32(rtl8169_tx_vlan_tag(tp, skb));
wmb();
/* anti gcc 2.95.3 bugware (sic) */
status = opts1 | len | (RingEnd * !((entry + 1) % NUM_TX_DESC));
txd->opts1 = cpu_to_le32(status);
dev->trans_start = jiffies;
tp->cur_tx += frags + 1;
smp_wmb();
RTL_W8(TxPoll, 0x40); /* set polling bit */
if (TX_BUFFS_AVAIL(tp) < MAX_SKB_FRAGS) {
netif_stop_queue(dev);
smp_rmb();
if (TX_BUFFS_AVAIL(tp) >= MAX_SKB_FRAGS)
netif_wake_queue(dev);
}
out:
return ret;
err_stop:
netif_stop_queue(dev);
ret = NETDEV_TX_BUSY;
err_update_stats:
tp->stats.tx_dropped++;
goto out;
}
static void rtl8169_pcierr_interrupt(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
struct pci_dev *pdev = tp->pci_dev;
void __iomem *ioaddr = tp->mmio_addr;
u16 pci_status, pci_cmd;
pci_read_config_word(pdev, PCI_COMMAND, &pci_cmd);
pci_read_config_word(pdev, PCI_STATUS, &pci_status);
if (netif_msg_intr(tp)) {
printk(KERN_ERR
"%s: PCI error (cmd = 0x%04x, status = 0x%04x).\n",
dev->name, pci_cmd, pci_status);
}
/*
* The recovery sequence below admits a very elaborated explanation:
* - it seems to work;
* - I did not see what else could be done;
* - it makes iop3xx happy.
*
* Feel free to adjust to your needs.
*/
if (ignore_parity_err)
pci_cmd &= ~PCI_COMMAND_PARITY;
else
pci_cmd |= PCI_COMMAND_SERR | PCI_COMMAND_PARITY;
pci_write_config_word(pdev, PCI_COMMAND, pci_cmd);
pci_write_config_word(pdev, PCI_STATUS,
pci_status & (PCI_STATUS_DETECTED_PARITY |
PCI_STATUS_SIG_SYSTEM_ERROR | PCI_STATUS_REC_MASTER_ABORT |
PCI_STATUS_REC_TARGET_ABORT | PCI_STATUS_SIG_TARGET_ABORT));
/* The infamous DAC f*ckup only happens at boot time */
if ((tp->cp_cmd & PCIDAC) && !tp->dirty_rx && !tp->cur_rx) {
if (netif_msg_intr(tp))
printk(KERN_INFO "%s: disabling PCI DAC.\n", dev->name);
tp->cp_cmd &= ~PCIDAC;
RTL_W16(CPlusCmd, tp->cp_cmd);
dev->features &= ~NETIF_F_HIGHDMA;
}
rtl8169_hw_reset(ioaddr);
rtl8169_schedule_work(dev, rtl8169_reinit_task);
}
static void
rtl8169_tx_interrupt(struct net_device *dev, struct rtl8169_private *tp,
void __iomem *ioaddr)
{
unsigned int dirty_tx, tx_left;
assert(dev != NULL);
assert(tp != NULL);
assert(ioaddr != NULL);
dirty_tx = tp->dirty_tx;
smp_rmb();
tx_left = tp->cur_tx - dirty_tx;
while (tx_left > 0) {
unsigned int entry = dirty_tx % NUM_TX_DESC;
struct ring_info *tx_skb = tp->tx_skb + entry;
u32 len = tx_skb->len;
u32 status;
rmb();
status = le32_to_cpu(tp->TxDescArray[entry].opts1);
if (status & DescOwn)
break;
tp->stats.tx_bytes += len;
tp->stats.tx_packets++;
rtl8169_unmap_tx_skb(tp->pci_dev, tx_skb, tp->TxDescArray + entry);
if (status & LastFrag) {
dev_kfree_skb_irq(tx_skb->skb);
tx_skb->skb = NULL;
}
dirty_tx++;
tx_left--;
}
if (tp->dirty_tx != dirty_tx) {
tp->dirty_tx = dirty_tx;
smp_wmb();
if (netif_queue_stopped(dev) &&
(TX_BUFFS_AVAIL(tp) >= MAX_SKB_FRAGS)) {
netif_wake_queue(dev);
}
}
}
static inline int rtl8169_fragmented_frame(u32 status)
{
return (status & (FirstFrag | LastFrag)) != (FirstFrag | LastFrag);
}
static inline void rtl8169_rx_csum(struct sk_buff *skb, struct RxDesc *desc)
{
u32 opts1 = le32_to_cpu(desc->opts1);
u32 status = opts1 & RxProtoMask;
if (((status == RxProtoTCP) && !(opts1 & TCPFail)) ||
((status == RxProtoUDP) && !(opts1 & UDPFail)) ||
((status == RxProtoIP) && !(opts1 & IPFail)))
skb->ip_summed = CHECKSUM_UNNECESSARY;
else
skb->ip_summed = CHECKSUM_NONE;
}
static inline int rtl8169_try_rx_copy(struct sk_buff **sk_buff, int pkt_size,
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
struct RxDesc *desc, int rx_buf_sz,
unsigned int align)
{
int ret = -1;
if (pkt_size < rx_copybreak) {
struct sk_buff *skb;
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
skb = dev_alloc_skb(pkt_size + align);
if (skb) {
skb_reserve(skb, (align - 1) & (u32)skb->data);
eth_copy_and_sum(skb, sk_buff[0]->data, pkt_size, 0);
*sk_buff = skb;
rtl8169_mark_to_asic(desc, rx_buf_sz);
ret = 0;
}
}
return ret;
}
static int
rtl8169_rx_interrupt(struct net_device *dev, struct rtl8169_private *tp,
void __iomem *ioaddr)
{
unsigned int cur_rx, rx_left;
unsigned int delta, count;
assert(dev != NULL);
assert(tp != NULL);
assert(ioaddr != NULL);
cur_rx = tp->cur_rx;
rx_left = NUM_RX_DESC + tp->dirty_rx - cur_rx;
rx_left = rtl8169_rx_quota(rx_left, (u32) dev->quota);
for (; rx_left > 0; rx_left--, cur_rx++) {
unsigned int entry = cur_rx % NUM_RX_DESC;
struct RxDesc *desc = tp->RxDescArray + entry;
u32 status;
rmb();
status = le32_to_cpu(desc->opts1);
if (status & DescOwn)
break;
if (unlikely(status & RxRES)) {
if (netif_msg_rx_err(tp)) {
printk(KERN_INFO
"%s: Rx ERROR. status = %08x\n",
dev->name, status);
}
tp->stats.rx_errors++;
if (status & (RxRWT | RxRUNT))
tp->stats.rx_length_errors++;
if (status & RxCRC)
tp->stats.rx_crc_errors++;
if (status & RxFOVF) {
rtl8169_schedule_work(dev, rtl8169_reset_task);
tp->stats.rx_fifo_errors++;
}
rtl8169_mark_to_asic(desc, tp->rx_buf_sz);
} else {
struct sk_buff *skb = tp->Rx_skbuff[entry];
int pkt_size = (status & 0x00001FFF) - 4;
void (*pci_action)(struct pci_dev *, dma_addr_t,
size_t, int) = pci_dma_sync_single_for_device;
/*
* The driver does not support incoming fragmented
* frames. They are seen as a symptom of over-mtu
* sized frames.
*/
if (unlikely(rtl8169_fragmented_frame(status))) {
tp->stats.rx_dropped++;
tp->stats.rx_length_errors++;
rtl8169_mark_to_asic(desc, tp->rx_buf_sz);
continue;
}
rtl8169_rx_csum(skb, desc);
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
pci_dma_sync_single_for_cpu(tp->pci_dev,
le64_to_cpu(desc->addr), tp->rx_buf_sz,
PCI_DMA_FROMDEVICE);
if (rtl8169_try_rx_copy(&skb, pkt_size, desc,
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
tp->rx_buf_sz, tp->align)) {
pci_action = pci_unmap_single;
tp->Rx_skbuff[entry] = NULL;
}
pci_action(tp->pci_dev, le64_to_cpu(desc->addr),
tp->rx_buf_sz, PCI_DMA_FROMDEVICE);
skb->dev = dev;
skb_put(skb, pkt_size);
skb->protocol = eth_type_trans(skb, dev);
if (rtl8169_rx_vlan_skb(tp, desc, skb) < 0)
rtl8169_rx_skb(skb);
dev->last_rx = jiffies;
tp->stats.rx_bytes += pkt_size;
tp->stats.rx_packets++;
}
}
count = cur_rx - tp->cur_rx;
tp->cur_rx = cur_rx;
delta = rtl8169_rx_fill(tp, dev, tp->dirty_rx, tp->cur_rx);
if (!delta && count && netif_msg_intr(tp))
printk(KERN_INFO "%s: no Rx buffer allocated\n", dev->name);
tp->dirty_rx += delta;
/*
* FIXME: until there is periodic timer to try and refill the ring,
* a temporary shortage may definitely kill the Rx process.
* - disable the asic to try and avoid an overflow and kick it again
* after refill ?
* - how do others driver handle this condition (Uh oh...).
*/
if ((tp->dirty_rx + NUM_RX_DESC == tp->cur_rx) && netif_msg_intr(tp))
printk(KERN_EMERG "%s: Rx buffers exhausted\n", dev->name);
return count;
}
/* The interrupt handler does all of the Rx thread work and cleans up after the Tx thread. */
static irqreturn_t
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 21:55:46 +08:00
rtl8169_interrupt(int irq, void *dev_instance)
{
struct net_device *dev = (struct net_device *) dev_instance;
struct rtl8169_private *tp = netdev_priv(dev);
int boguscnt = max_interrupt_work;
void __iomem *ioaddr = tp->mmio_addr;
int status;
int handled = 0;
do {
status = RTL_R16(IntrStatus);
/* hotplug/major error/no more work/shared irq */
if ((status == 0xFFFF) || !status)
break;
handled = 1;
if (unlikely(!netif_running(dev))) {
rtl8169_asic_down(ioaddr);
goto out;
}
status &= tp->intr_mask;
RTL_W16(IntrStatus,
(status & RxFIFOOver) ? (status | RxOverflow) : status);
if (!(status & rtl8169_intr_mask))
break;
if (unlikely(status & SYSErr)) {
rtl8169_pcierr_interrupt(dev);
break;
}
if (status & LinkChg)
rtl8169_check_link_status(dev, tp, ioaddr);
#ifdef CONFIG_R8169_NAPI
RTL_W16(IntrMask, rtl8169_intr_mask & ~rtl8169_napi_event);
tp->intr_mask = ~rtl8169_napi_event;
if (likely(netif_rx_schedule_prep(dev)))
__netif_rx_schedule(dev);
else if (netif_msg_intr(tp)) {
printk(KERN_INFO "%s: interrupt %04x taken in poll\n",
dev->name, status);
}
break;
#else
/* Rx interrupt */
if (status & (RxOK | RxOverflow | RxFIFOOver)) {
rtl8169_rx_interrupt(dev, tp, ioaddr);
}
/* Tx interrupt */
if (status & (TxOK | TxErr))
rtl8169_tx_interrupt(dev, tp, ioaddr);
#endif
boguscnt--;
} while (boguscnt > 0);
if (boguscnt <= 0) {
if (netif_msg_intr(tp) && net_ratelimit() ) {
printk(KERN_WARNING
"%s: Too much work at interrupt!\n", dev->name);
}
/* Clear all interrupt sources. */
RTL_W16(IntrStatus, 0xffff);
}
out:
return IRQ_RETVAL(handled);
}
#ifdef CONFIG_R8169_NAPI
static int rtl8169_poll(struct net_device *dev, int *budget)
{
unsigned int work_done, work_to_do = min(*budget, dev->quota);
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
work_done = rtl8169_rx_interrupt(dev, tp, ioaddr);
rtl8169_tx_interrupt(dev, tp, ioaddr);
*budget -= work_done;
dev->quota -= work_done;
if (work_done < work_to_do) {
netif_rx_complete(dev);
tp->intr_mask = 0xffff;
/*
* 20040426: the barrier is not strictly required but the
* behavior of the irq handler could be less predictable
* without it. Btw, the lack of flush for the posted pci
* write is safe - FR
*/
smp_wmb();
RTL_W16(IntrMask, rtl8169_intr_mask);
}
return (work_done >= work_to_do);
}
#endif
static void rtl8169_down(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
unsigned int poll_locked = 0;
unsigned int intrmask;
rtl8169_delete_timer(dev);
netif_stop_queue(dev);
flush_scheduled_work();
core_down:
spin_lock_irq(&tp->lock);
rtl8169_asic_down(ioaddr);
/* Update the error counts. */
tp->stats.rx_missed_errors += RTL_R32(RxMissed);
RTL_W32(RxMissed, 0);
spin_unlock_irq(&tp->lock);
synchronize_irq(dev->irq);
if (!poll_locked) {
netif_poll_disable(dev);
poll_locked++;
}
/* Give a racing hard_start_xmit a few cycles to complete. */
synchronize_sched(); /* FIXME: should this be synchronize_irq()? */
/*
* And now for the 50k$ question: are IRQ disabled or not ?
*
* Two paths lead here:
* 1) dev->close
* -> netif_running() is available to sync the current code and the
* IRQ handler. See rtl8169_interrupt for details.
* 2) dev->change_mtu
* -> rtl8169_poll can not be issued again and re-enable the
* interruptions. Let's simply issue the IRQ down sequence again.
*
* No loop if hotpluged or major error (0xffff).
*/
intrmask = RTL_R16(IntrMask);
if (intrmask && (intrmask != 0xffff))
goto core_down;
rtl8169_tx_clear(tp);
rtl8169_rx_clear(tp);
}
static int rtl8169_close(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
struct pci_dev *pdev = tp->pci_dev;
rtl8169_down(dev);
free_irq(dev->irq, dev);
netif_poll_enable(dev);
pci_free_consistent(pdev, R8169_RX_RING_BYTES, tp->RxDescArray,
tp->RxPhyAddr);
pci_free_consistent(pdev, R8169_TX_RING_BYTES, tp->TxDescArray,
tp->TxPhyAddr);
tp->TxDescArray = NULL;
tp->RxDescArray = NULL;
return 0;
}
static void
rtl8169_set_rx_mode(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
unsigned long flags;
u32 mc_filter[2]; /* Multicast hash filter */
int i, rx_mode;
u32 tmp = 0;
if (dev->flags & IFF_PROMISC) {
/* Unconditionally log net taps. */
if (netif_msg_link(tp)) {
printk(KERN_NOTICE "%s: Promiscuous mode enabled.\n",
dev->name);
}
rx_mode =
AcceptBroadcast | AcceptMulticast | AcceptMyPhys |
AcceptAllPhys;
mc_filter[1] = mc_filter[0] = 0xffffffff;
} else if ((dev->mc_count > multicast_filter_limit)
|| (dev->flags & IFF_ALLMULTI)) {
/* Too many to filter perfectly -- accept all multicasts. */
rx_mode = AcceptBroadcast | AcceptMulticast | AcceptMyPhys;
mc_filter[1] = mc_filter[0] = 0xffffffff;
} else {
struct dev_mc_list *mclist;
rx_mode = AcceptBroadcast | AcceptMyPhys;
mc_filter[1] = mc_filter[0] = 0;
for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count;
i++, mclist = mclist->next) {
int bit_nr = ether_crc(ETH_ALEN, mclist->dmi_addr) >> 26;
mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31);
rx_mode |= AcceptMulticast;
}
}
spin_lock_irqsave(&tp->lock, flags);
tmp = rtl8169_rx_config | rx_mode |
(RTL_R32(RxConfig) & rtl_chip_info[tp->chipset].RxConfigMask);
r8169: sync with vendor's driver - add several PCI ID for the PCI-E adapters ; - new identification strings ; - the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the out-of-tree driver. It makes the comparison less hairy ; - various magic ; - the PCI region for the device with PCI ID 0x8136 is guessed. Explanation: the in-kernel Linux driver is written to allow MM register accesses and avoid the IO tax. The relevant BAR register was found at base address 1 for the plain-old PCI 8169. User reported lspci show that it is found at base address 2 for the new Gigabit PCI-E 816{8/9}. Typically: 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01) Subsystem: Unknown device 1631:e015 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 20 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at b800 [size=256] Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K] ^^^^^^^^ So far I have not received any lspci report for the 0x8136 and Realtek's driver do not help: be it under BSD or Linux, their r1000 driver include a USE_IO_SPACE #define but the bar address is always hardcoded to 1 in the MM case. :o/ - the 8168 has been reported to require an extra alignment for its receive buffers. The status of the 8167 and 8136 is not known in this regard. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
2006-07-27 05:14:13 +08:00
if ((tp->mac_version == RTL_GIGA_MAC_VER_11) ||
(tp->mac_version == RTL_GIGA_MAC_VER_12) ||
(tp->mac_version == RTL_GIGA_MAC_VER_13) ||
(tp->mac_version == RTL_GIGA_MAC_VER_14) ||
(tp->mac_version == RTL_GIGA_MAC_VER_15)) {
mc_filter[0] = 0xffffffff;
mc_filter[1] = 0xffffffff;
}
RTL_W32(RxConfig, tmp);
RTL_W32(MAR0 + 0, mc_filter[0]);
RTL_W32(MAR0 + 4, mc_filter[1]);
spin_unlock_irqrestore(&tp->lock, flags);
}
/**
* rtl8169_get_stats - Get rtl8169 read/write statistics
* @dev: The Ethernet Device to get statistics for
*
* Get TX/RX statistics for rtl8169
*/
static struct net_device_stats *rtl8169_get_stats(struct net_device *dev)
{
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
unsigned long flags;
if (netif_running(dev)) {
spin_lock_irqsave(&tp->lock, flags);
tp->stats.rx_missed_errors += RTL_R32(RxMissed);
RTL_W32(RxMissed, 0);
spin_unlock_irqrestore(&tp->lock, flags);
}
return &tp->stats;
}
#ifdef CONFIG_PM
static int rtl8169_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct net_device *dev = pci_get_drvdata(pdev);
struct rtl8169_private *tp = netdev_priv(dev);
void __iomem *ioaddr = tp->mmio_addr;
if (!netif_running(dev))
goto out;
netif_device_detach(dev);
netif_stop_queue(dev);
spin_lock_irq(&tp->lock);
rtl8169_asic_down(ioaddr);
tp->stats.rx_missed_errors += RTL_R32(RxMissed);
RTL_W32(RxMissed, 0);
spin_unlock_irq(&tp->lock);
pci_save_state(pdev);
pci_enable_wake(pdev, pci_choose_state(pdev, state), tp->wol_enabled);
pci_set_power_state(pdev, pci_choose_state(pdev, state));
out:
return 0;
}
static int rtl8169_resume(struct pci_dev *pdev)
{
struct net_device *dev = pci_get_drvdata(pdev);
if (!netif_running(dev))
goto out;
netif_device_attach(dev);
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
rtl8169_schedule_work(dev, rtl8169_reset_task);
out:
return 0;
}
#endif /* CONFIG_PM */
static struct pci_driver rtl8169_pci_driver = {
.name = MODULENAME,
.id_table = rtl8169_pci_tbl,
.probe = rtl8169_init_one,
.remove = __devexit_p(rtl8169_remove_one),
#ifdef CONFIG_PM
.suspend = rtl8169_suspend,
.resume = rtl8169_resume,
#endif
};
static int __init
rtl8169_init_module(void)
{
return pci_register_driver(&rtl8169_pci_driver);
}
static void __exit
rtl8169_cleanup_module(void)
{
pci_unregister_driver(&rtl8169_pci_driver);
}
module_init(rtl8169_init_module);
module_exit(rtl8169_cleanup_module);