OpenCloudOS-Kernel/drivers/net/phy/Kconfig

499 lines
14 KiB
Plaintext
Raw Normal View History

# SPDX-License-Identifier: GPL-2.0-only
#
# PHY Layer Configuration
#
menuconfig MDIO_DEVICE
tristate "MDIO bus device drivers"
help
MDIO devices and driver infrastructure code.
if MDIO_DEVICE
config MDIO_BUS
tristate
default m if PHYLIB=m
default MDIO_DEVICE
help
This internal symbol is used for link time dependencies and it
reflects whether the mdio_bus/mdio_device code is built as a
loadable module or built-in.
if MDIO_BUS
config MDIO_ASPEED
tristate "ASPEED MDIO bus controller"
depends on ARCH_ASPEED || COMPILE_TEST
depends on OF_MDIO && HAS_IOMEM
help
This module provides a driver for the independent MDIO bus
controllers found in the ASPEED AST2600 SoC. This is a driver for the
third revision of the ASPEED MDIO register interface - the first two
revisions are the "old" and "new" interfaces found in the AST2400 and
AST2500, embedded in the MAC. For legacy reasons, FTGMAC100 driver
continues to drive the embedded MDIO controller for the AST2400 and
AST2500 SoCs, so say N if AST2600 support is not required.
config MDIO_BCM_IPROC
tristate "Broadcom iProc MDIO bus controller"
depends on ARCH_BCM_IPROC || COMPILE_TEST
depends on HAS_IOMEM && OF_MDIO
help
This module provides a driver for the MDIO busses found in the
Broadcom iProc SoC's.
config MDIO_BCM_UNIMAC
tristate "Broadcom UniMAC MDIO bus controller"
depends on HAS_IOMEM
help
This module provides a driver for the Broadcom UniMAC MDIO busses.
This hardware can be found in the Broadcom GENET Ethernet MAC
controllers as well as some Broadcom Ethernet switches such as the
Starfighter 2 switches.
config MDIO_BITBANG
tristate "Bitbanged MDIO buses"
help
This module implements the MDIO bus protocol in software,
for use by low level drivers that export the ability to
drive the relevant pins.
If in doubt, say N.
config MDIO_BUS_MUX
tristate
depends on OF_MDIO
help
This module provides a driver framework for MDIO bus
multiplexers which connect one of several child MDIO busses
to a parent bus. Switching between child busses is done by
device specific drivers.
config MDIO_BUS_MUX_BCM_IPROC
tristate "Broadcom iProc based MDIO bus multiplexers"
depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
select MDIO_BUS_MUX
default ARCH_BCM_IPROC
help
This module provides a driver for MDIO bus multiplexers found in
iProc based Broadcom SoCs. This multiplexer connects one of several
child MDIO bus to a parent bus. Buses could be internal as well as
external and selection logic lies inside the same multiplexer.
config MDIO_BUS_MUX_GPIO
tristate "GPIO controlled MDIO bus multiplexers"
depends on OF_GPIO && OF_MDIO
select MDIO_BUS_MUX
help
This module provides a driver for MDIO bus multiplexers that
are controlled via GPIO lines. The multiplexer connects one of
several child MDIO busses to a parent bus. Child bus
selection is under the control of GPIO lines.
config MDIO_BUS_MUX_MESON_G12A
tristate "Amlogic G12a based MDIO bus multiplexer"
depends on ARCH_MESON || COMPILE_TEST
depends on OF_MDIO && HAS_IOMEM && COMMON_CLK
select MDIO_BUS_MUX
default m if ARCH_MESON
help
This module provides a driver for the MDIO multiplexer/glue of
the amlogic g12a SoC. The multiplexers connects either the external
or the internal MDIO bus to the parent bus.
config MDIO_BUS_MUX_MMIOREG
tristate "MMIO device-controlled MDIO bus multiplexers"
depends on OF_MDIO && HAS_IOMEM
select MDIO_BUS_MUX
help
This module provides a driver for MDIO bus multiplexers that
are controlled via a simple memory-mapped device, like an FPGA.
The multiplexer connects one of several child MDIO busses to a
parent bus. Child bus selection is under the control of one of
the FPGA's registers.
Currently, only 8/16/32 bits registers are supported.
config MDIO_BUS_MUX_MULTIPLEXER
tristate "MDIO bus multiplexer using kernel multiplexer subsystem"
depends on OF_MDIO
select MULTIPLEXER
select MDIO_BUS_MUX
help
This module provides a driver for MDIO bus multiplexer
that is controlled via the kernel multiplexer subsystem. The
bus multiplexer connects one of several child MDIO busses to
a parent bus. Child bus selection is under the control of
the kernel multiplexer subsystem.
config MDIO_CAVIUM
tristate
config MDIO_GPIO
tristate "GPIO lib-based bitbanged MDIO buses"
depends on MDIO_BITBANG
depends on GPIOLIB || COMPILE_TEST
---help---
Supports GPIO lib-based MDIO busses.
To compile this driver as a module, choose M here: the module
will be called mdio-gpio.
config MDIO_HISI_FEMAC
tristate "Hisilicon FEMAC MDIO bus controller"
depends on HAS_IOMEM && OF_MDIO
help
This module provides a driver for the MDIO busses found in the
Hisilicon SoC that have an Fast Ethernet MAC.
config MDIO_I2C
tristate
depends on I2C
help
Support I2C based PHYs. This provides a MDIO bus bridged
to I2C to allow PHYs connected in I2C mode to be accessed
using the existing infrastructure.
This is library mode.
config MDIO_MOXART
tristate "MOXA ART MDIO interface support"
depends on ARCH_MOXART || COMPILE_TEST
help
This driver supports the MDIO interface found in the network
interface units of the MOXA ART SoC
config MDIO_MSCC_MIIM
tristate "Microsemi MIIM interface support"
depends on HAS_IOMEM
help
This driver supports the MIIM (MDIO) interface found in the network
switches of the Microsemi SoCs
config MDIO_OCTEON
tristate "Octeon and some ThunderX SOCs MDIO buses"
net: mdio-octeon: Fix Kconfig warnings and build errors After commit 171a9bae68c7 ("staging/octeon: Allow test build on !MIPS"), the following combination of configs cause a few Kconfig warnings and build errors (distilled from arm allyesconfig and Randy's randconfig builds): CONFIG_NETDEVICES=y CONFIG_STAGING=y CONFIG_COMPILE_TEST=y and CONFIG_OCTEON_ETHERNET as either a module or built-in. WARNING: unmet direct dependencies detected for MDIO_OCTEON Depends on [n]: NETDEVICES [=y] && MDIO_DEVICE [=y] && MDIO_BUS [=y] && 64BIT [=n] && HAS_IOMEM [=y] && OF_MDIO [=n] Selected by [y]: - OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC || COMPILE_TEST [=y]) && NETDEVICES [=y] In file included from ../drivers/net/phy/mdio-octeon.c:14: ../drivers/net/phy/mdio-cavium.h:111:36: error: implicit declaration of function ‘writeq’; did you mean ‘writel’? [-Werror=implicit-function-declaration] 111 | #define oct_mdio_writeq(val, addr) writeq(val, (void *)addr) | ^~~~~~ CONFIG_64BIT is not strictly necessary if the proper readq/writeq definitions are included from io-64-nonatomic-lo-hi.h. CONFIG_OF_MDIO is not needed when CONFIG_COMPILE_TEST is enabled because of commit f9dc9ac51610 ("of/mdio: Add dummy functions in of_mdio.h."). Fixes: 171a9bae68c7 ("staging/octeon: Allow test build on !MIPS") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Mark Brown <broonie@kernel.org> Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-03 14:01:56 +08:00
depends on (64BIT && OF_MDIO) || COMPILE_TEST
depends on HAS_IOMEM
select MDIO_CAVIUM
help
This module provides a driver for the Octeon and ThunderX MDIO
buses. It is required by the Octeon and ThunderX ethernet device
drivers on some systems.
config MDIO_SUN4I
tristate "Allwinner sun4i MDIO interface support"
depends on ARCH_SUNXI || COMPILE_TEST
help
This driver supports the MDIO interface found in the network
interface units of the Allwinner SoC that have an EMAC (A10,
A12, A10s, etc.)
config MDIO_THUNDER
tristate "ThunderX SOCs MDIO buses"
depends on 64BIT
depends on PCI
select MDIO_CAVIUM
help
This driver supports the MDIO interfaces found on Cavium
ThunderX SoCs when the MDIO bus device appears as a PCI
device.
config MDIO_XGENE
tristate "APM X-Gene SoC MDIO bus controller"
depends on ARCH_XGENE || COMPILE_TEST
help
This module provides a driver for the MDIO busses found in the
APM X-Gene SoC's.
endif
endif
phylink: add phylink infrastructure The link between the ethernet MAC and its PHY has become more complex as the interface evolves. This is especially true with serdes links, where the part of the PHY is effectively integrated into the MAC. Serdes links can be connected to a variety of devices, including SFF modules soldered down onto the board with the MAC, a SFP cage with a hotpluggable SFP module which may contain a PHY or directly modulate the serdes signals onto optical media with or without a PHY, or even a classical PHY connection. Moreover, the negotiation information on serdes links comes in two varieties - SGMII mode, where the PHY provides its speed/duplex/flow control information to the MAC, and 1000base-X mode where both ends exchange their abilities and each resolve the link capabilities. This means we need a more flexible means to support these arrangements, particularly with the hotpluggable nature of SFP, where the PHY can be attached or detached after the network device has been brought up. Ethtool information can come from multiple sources: - we may have a PHY operating in either SGMII or 1000base-X mode, in which case we take ethtool/mii data directly from the PHY. - we may have a optical SFP module without a PHY, with the MAC operating in 1000base-X mode - the ethtool/mii data needs to come from the MAC. - we may have a copper SFP module with a PHY whic can't be accessed, which means we need to take ethtool/mii data from the MAC. Phylink aims to solve this by providing an intermediary between the MAC and PHY, providing a safe way for PHYs to be hotplugged, and allowing a SFP driver to reconfigure the serdes connection. Phylink also takes over support of fixed link connections, where the speed/duplex/flow control are fixed, but link status may be controlled by a GPIO signal. By avoiding the fixed-phy implementation, phylink can provide a faster response to link events: fixed-phy has to wait for phylib to operate its state machine, which can take several seconds. In comparison, phylink takes milliseconds. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> - remove sync status - rework supported and advertisment handling - add 1000base-x speed for fixed links - use functionality exported from phy-core, reworking __phylink_ethtool_ksettings_set for it Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-25 22:03:13 +08:00
config PHYLINK
tristate
depends on NETDEVICES
select PHYLIB
select SWPHY
help
PHYlink models the link between the PHY and MAC, allowing fixed
configuration links, PHYs, and Serdes links with MAC level
autonegotiation modes.
menuconfig PHYLIB
tristate "PHY Device support and infrastructure"
depends on NETDEVICES
select MDIO_DEVICE
help
Ethernet controllers are usually attached to PHY
devices. This option provides infrastructure for
managing PHY devices.
if PHYLIB
config SWPHY
bool
config LED_TRIGGER_PHY
bool "Support LED triggers for tracking link state"
depends on LEDS_TRIGGERS
---help---
Adds support for a set of LED trigger events per-PHY. Link
state change will trigger the events, for consumption by an
LED class driver. There are triggers for each link speed currently
supported by the PHY and also a one common "link" trigger as a
logical-or of all the link speed ones.
All these triggers are named according to the following pattern:
<mii bus id>:<phy>:<speed>
Where speed is in the form:
<Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link
for any speed known to the PHY.
comment "MII PHY device drivers"
config SFP
tristate "SFP cage support"
depends on I2C && PHYLINK
depends on HWMON || HWMON=n
select MDIO_I2C
config ADIN_PHY
tristate "Analog Devices Industrial Ethernet PHYs"
help
Adds support for the Analog Devices Industrial Ethernet PHYs.
Currently supports the:
- ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY
- ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
config AMD_PHY
tristate "AMD PHYs"
---help---
Currently supports the am79c874
config AQUANTIA_PHY
tristate "Aquantia PHYs"
---help---
Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405
config AX88796B_PHY
tristate "Asix PHYs"
help
Currently supports the Asix Electronics PHY found in the X-Surf 100
AX88796B package.
config AT803X_PHY
tristate "AT803X PHYs"
---help---
Currently supports the AT8030 and AT8035 model
config BCM63XX_PHY
tristate "Broadcom 63xx SOCs internal PHY"
depends on BCM63XX || COMPILE_TEST
select BCM_NET_PHYLIB
---help---
Currently supports the 6348 and 6358 PHYs.
config BCM7XXX_PHY
tristate "Broadcom 7xxx SOCs internal PHYs"
select BCM_NET_PHYLIB
---help---
Currently supports the BCM7366, BCM7439, BCM7445, and
40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
config BCM87XX_PHY
tristate "Broadcom BCM8706 and BCM8727 PHYs"
help
Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
config BCM_CYGNUS_PHY
tristate "Broadcom Cygnus/Omega SoC internal PHY"
depends on ARCH_BCM_IPROC || COMPILE_TEST
depends on MDIO_BCM_IPROC
select BCM_NET_PHYLIB
---help---
This PHY driver is for the 1G internal PHYs of the Broadcom
Cygnus and Omega Family SoC.
Currently supports internal PHY's used in the BCM11300,
BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
BCM58303 & BCM58305 Broadcom Cygnus SoCs.
config BCM_NET_PHYLIB
tristate
config BROADCOM_PHY
tristate "Broadcom PHYs"
select BCM_NET_PHYLIB
---help---
Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
BCM5481, BCM54810 and BCM5482 PHYs.
config CICADA_PHY
tristate "Cicada PHYs"
---help---
Currently supports the cis8204
config CORTINA_PHY
tristate "Cortina EDC CDR 10G Ethernet PHY"
---help---
Currently supports the CS4340 phy.
config DAVICOM_PHY
tristate "Davicom PHYs"
---help---
Currently supports dm9161e and dm9131
config DP83822_PHY
tristate "Texas Instruments DP83822 PHY"
---help---
Supports the DP83822 PHY.
config DP83TC811_PHY
tristate "Texas Instruments DP83TC822 PHY"
---help---
Supports the DP83TC822 PHY.
config DP83848_PHY
tristate "Texas Instruments DP83848 PHY"
---help---
Supports the DP83848 PHY.
config DP83867_PHY
tristate "Texas Instruments DP83867 Gigabit PHY"
---help---
Currently supports the DP83867 PHY.
config FIXED_PHY
tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
depends on PHYLIB
select SWPHY
---help---
Adds the platform "fixed" MDIO Bus to cover the boards that use
PHYs that are not connected to the real MDIO bus.
Currently tested with mpc866ads and mpc8349e-mitx.
config ICPLUS_PHY
tristate "ICPlus PHYs"
---help---
Currently supports the IP175C and IP1001 PHYs.
config INTEL_XWAY_PHY
tristate "Intel XWAY PHYs"
---help---
Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
These PHYs are marked as standalone chips under the names
PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
config LSI_ET1011C_PHY
tristate "LSI ET1011C PHY"
---help---
Supports the LSI ET1011C PHY.
config LXT_PHY
tristate "Intel LXT PHYs"
---help---
Currently supports the lxt970, lxt971
config MARVELL_PHY
tristate "Marvell PHYs"
---help---
Currently has a driver for the 88E1011S
config MARVELL_10G_PHY
tristate "Marvell Alaska 10Gbit PHYs"
---help---
Support for the Marvell Alaska MV88X3310 and compatible PHYs.
config MESON_GXL_PHY
tristate "Amlogic Meson GXL Internal PHY"
depends on ARCH_MESON || COMPILE_TEST
---help---
Currently has a driver for the Amlogic Meson GXL Internal PHY
config MICREL_PHY
tristate "Micrel PHYs"
---help---
Supports the KSZ9021, VSC8201, KS8001 PHYs.
config MICROCHIP_PHY
tristate "Microchip PHYs"
help
Supports the LAN88XX PHYs.
config MICROCHIP_T1_PHY
tristate "Microchip T1 PHYs"
---help---
Supports the LAN87XX PHYs.
config MICROSEMI_PHY
tristate "Microsemi PHYs"
---help---
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 19:51:35 +08:00
Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
config NATIONAL_PHY
tristate "National Semiconductor PHYs"
---help---
Currently supports the DP83865 PHY.
config NXP_TJA11XX_PHY
tristate "NXP TJA11xx PHYs support"
depends on HWMON
---help---
Currently supports the NXP TJA1100 and TJA1101 PHY.
config QSEMI_PHY
tristate "Quality Semiconductor PHYs"
---help---
Currently supports the qs6612
config REALTEK_PHY
tristate "Realtek PHYs"
---help---
Supports the Realtek 821x PHY.
config RENESAS_PHY
tristate "Driver for Renesas PHYs"
---help---
Supports the Renesas PHYs uPD60620 and uPD60620A.
config ROCKCHIP_PHY
tristate "Driver for Rockchip Ethernet PHYs"
---help---
Currently supports the integrated Ethernet PHY.
config SMSC_PHY
tristate "SMSC PHYs"
---help---
Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
config STE10XP
tristate "STMicroelectronics STe10Xp PHYs"
---help---
This is the driver for the STe100p and STe101p PHYs.
config TERANETICS_PHY
tristate "Teranetics PHYs"
---help---
Currently supports the Teranetics TN2020
config VITESSE_PHY
tristate "Vitesse PHYs"
---help---
Currently supports the vsc8244
config XILINX_GMII2RGMII
tristate "Xilinx GMII2RGMII converter driver"
---help---
This driver support xilinx GMII to RGMII IP core it provides
the Reduced Gigabit Media Independent Interface(RGMII) between
Ethernet physical media devices and the Gigabit Ethernet controller.
endif # PHYLIB
config MICREL_KS8995MA
tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
depends on SPI