OpenCloudOS-Kernel/drivers/gpio/gpio-pl061.c

442 lines
11 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2008, 2009 Provigent Ltd.
*
* Author: Baruch Siach <baruch@tkos.co.il>
*
* Driver for the ARM PrimeCell(tm) General Purpose Input/Output (PL061)
*
* Data sheet: ARM DDI 0190B, September 2000
*/
#include <linux/amba/bus.h>
#include <linux/bitops.h>
#include <linux/device.h>
#include <linux/errno.h>
#include <linux/gpio/driver.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/irq.h>
#include <linux/irqchip/chained_irq.h>
#include <linux/module.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pm.h>
#include <linux/seq_file.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#define GPIODIR 0x400
#define GPIOIS 0x404
#define GPIOIBE 0x408
#define GPIOIEV 0x40C
#define GPIOIE 0x410
#define GPIORIS 0x414
#define GPIOMIS 0x418
#define GPIOIC 0x41C
#define PL061_GPIO_NR 8
#ifdef CONFIG_PM
struct pl061_context_save_regs {
u8 gpio_data;
u8 gpio_dir;
u8 gpio_is;
u8 gpio_ibe;
u8 gpio_iev;
u8 gpio_ie;
};
#endif
struct pl061 {
raw_spinlock_t lock;
void __iomem *base;
struct gpio_chip gc;
int parent_irq;
#ifdef CONFIG_PM
struct pl061_context_save_regs csave_regs;
#endif
};
static int pl061_get_direction(struct gpio_chip *gc, unsigned offset)
{
struct pl061 *pl061 = gpiochip_get_data(gc);
if (readb(pl061->base + GPIODIR) & BIT(offset))
return GPIO_LINE_DIRECTION_OUT;
return GPIO_LINE_DIRECTION_IN;
}
static int pl061_direction_input(struct gpio_chip *gc, unsigned offset)
{
struct pl061 *pl061 = gpiochip_get_data(gc);
unsigned long flags;
unsigned char gpiodir;
raw_spin_lock_irqsave(&pl061->lock, flags);
gpiodir = readb(pl061->base + GPIODIR);
gpiodir &= ~(BIT(offset));
writeb(gpiodir, pl061->base + GPIODIR);
raw_spin_unlock_irqrestore(&pl061->lock, flags);
return 0;
}
static int pl061_direction_output(struct gpio_chip *gc, unsigned offset,
int value)
{
struct pl061 *pl061 = gpiochip_get_data(gc);
unsigned long flags;
unsigned char gpiodir;
raw_spin_lock_irqsave(&pl061->lock, flags);
writeb(!!value << offset, pl061->base + (BIT(offset + 2)));
gpiodir = readb(pl061->base + GPIODIR);
gpiodir |= BIT(offset);
writeb(gpiodir, pl061->base + GPIODIR);
/*
* gpio value is set again, because pl061 doesn't allow to set value of
* a gpio pin before configuring it in OUT mode.
*/
writeb(!!value << offset, pl061->base + (BIT(offset + 2)));
raw_spin_unlock_irqrestore(&pl061->lock, flags);
return 0;
}
static int pl061_get_value(struct gpio_chip *gc, unsigned offset)
{
struct pl061 *pl061 = gpiochip_get_data(gc);
return !!readb(pl061->base + (BIT(offset + 2)));
}
static void pl061_set_value(struct gpio_chip *gc, unsigned offset, int value)
{
struct pl061 *pl061 = gpiochip_get_data(gc);
writeb(!!value << offset, pl061->base + (BIT(offset + 2)));
}
static int pl061_irq_type(struct irq_data *d, unsigned trigger)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061 *pl061 = gpiochip_get_data(gc);
int offset = irqd_to_hwirq(d);
unsigned long flags;
u8 gpiois, gpioibe, gpioiev;
u8 bit = BIT(offset);
if (offset < 0 || offset >= PL061_GPIO_NR)
return -EINVAL;
if ((trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) &&
(trigger & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)))
{
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 16:56:26 +08:00
dev_err(gc->parent,
"trying to configure line %d for both level and edge "
"detection, choose one!\n",
offset);
return -EINVAL;
}
raw_spin_lock_irqsave(&pl061->lock, flags);
gpioiev = readb(pl061->base + GPIOIEV);
gpiois = readb(pl061->base + GPIOIS);
gpioibe = readb(pl061->base + GPIOIBE);
if (trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
bool polarity = trigger & IRQ_TYPE_LEVEL_HIGH;
/* Disable edge detection */
gpioibe &= ~bit;
/* Enable level detection */
gpiois |= bit;
/* Select polarity */
if (polarity)
gpioiev |= bit;
else
gpioiev &= ~bit;
irq_set_handler_locked(d, handle_level_irq);
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 16:56:26 +08:00
dev_dbg(gc->parent, "line %d: IRQ on %s level\n",
offset,
polarity ? "HIGH" : "LOW");
} else if ((trigger & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH) {
/* Disable level detection */
gpiois &= ~bit;
/* Select both edges, setting this makes GPIOEV be ignored */
gpioibe |= bit;
irq_set_handler_locked(d, handle_edge_irq);
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 16:56:26 +08:00
dev_dbg(gc->parent, "line %d: IRQ on both edges\n", offset);
} else if ((trigger & IRQ_TYPE_EDGE_RISING) ||
(trigger & IRQ_TYPE_EDGE_FALLING)) {
bool rising = trigger & IRQ_TYPE_EDGE_RISING;
/* Disable level detection */
gpiois &= ~bit;
/* Clear detection on both edges */
gpioibe &= ~bit;
/* Select edge */
if (rising)
gpioiev |= bit;
else
gpioiev &= ~bit;
irq_set_handler_locked(d, handle_edge_irq);
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 16:56:26 +08:00
dev_dbg(gc->parent, "line %d: IRQ on %s edge\n",
offset,
rising ? "RISING" : "FALLING");
} else {
/* No trigger: disable everything */
gpiois &= ~bit;
gpioibe &= ~bit;
gpioiev &= ~bit;
irq_set_handler_locked(d, handle_bad_irq);
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 16:56:26 +08:00
dev_warn(gc->parent, "no trigger selected for line %d\n",
offset);
}
writeb(gpiois, pl061->base + GPIOIS);
writeb(gpioibe, pl061->base + GPIOIBE);
writeb(gpioiev, pl061->base + GPIOIEV);
raw_spin_unlock_irqrestore(&pl061->lock, flags);
return 0;
}
static void pl061_irq_handler(struct irq_desc *desc)
{
unsigned long pending;
int offset;
struct gpio_chip *gc = irq_desc_get_handler_data(desc);
struct pl061 *pl061 = gpiochip_get_data(gc);
struct irq_chip *irqchip = irq_desc_get_chip(desc);
chained_irq_enter(irqchip, desc);
pending = readb(pl061->base + GPIOMIS);
if (pending) {
for_each_set_bit(offset, &pending, PL061_GPIO_NR)
generic_handle_domain_irq(gc->irq.domain,
offset);
}
chained_irq_exit(irqchip, desc);
}
static void pl061_irq_mask(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061 *pl061 = gpiochip_get_data(gc);
u8 mask = BIT(irqd_to_hwirq(d) % PL061_GPIO_NR);
u8 gpioie;
raw_spin_lock(&pl061->lock);
gpioie = readb(pl061->base + GPIOIE) & ~mask;
writeb(gpioie, pl061->base + GPIOIE);
raw_spin_unlock(&pl061->lock);
gpiochip_disable_irq(gc, d->hwirq);
}
static void pl061_irq_unmask(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061 *pl061 = gpiochip_get_data(gc);
u8 mask = BIT(irqd_to_hwirq(d) % PL061_GPIO_NR);
u8 gpioie;
gpiochip_enable_irq(gc, d->hwirq);
raw_spin_lock(&pl061->lock);
gpioie = readb(pl061->base + GPIOIE) | mask;
writeb(gpioie, pl061->base + GPIOIE);
raw_spin_unlock(&pl061->lock);
}
/**
* pl061_irq_ack() - ACK an edge IRQ
* @d: IRQ data for this IRQ
*
* This gets called from the edge IRQ handler to ACK the edge IRQ
* in the GPIOIC (interrupt-clear) register. For level IRQs this is
* not needed: these go away when the level signal goes away.
*/
static void pl061_irq_ack(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061 *pl061 = gpiochip_get_data(gc);
u8 mask = BIT(irqd_to_hwirq(d) % PL061_GPIO_NR);
raw_spin_lock(&pl061->lock);
writeb(mask, pl061->base + GPIOIC);
raw_spin_unlock(&pl061->lock);
}
static int pl061_irq_set_wake(struct irq_data *d, unsigned int state)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061 *pl061 = gpiochip_get_data(gc);
return irq_set_irq_wake(pl061->parent_irq, state);
}
static void pl061_irq_print_chip(struct irq_data *data, struct seq_file *p)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
seq_printf(p, dev_name(gc->parent));
}
static const struct irq_chip pl061_irq_chip = {
.irq_ack = pl061_irq_ack,
.irq_mask = pl061_irq_mask,
.irq_unmask = pl061_irq_unmask,
.irq_set_type = pl061_irq_type,
.irq_set_wake = pl061_irq_set_wake,
.irq_print_chip = pl061_irq_print_chip,
.flags = IRQCHIP_IMMUTABLE,
GPIOCHIP_IRQ_RESOURCE_HELPERS,
};
static int pl061_probe(struct amba_device *adev, const struct amba_id *id)
{
struct device *dev = &adev->dev;
struct pl061 *pl061;
struct gpio_irq_chip *girq;
int ret, irq;
pl061 = devm_kzalloc(dev, sizeof(*pl061), GFP_KERNEL);
if (pl061 == NULL)
return -ENOMEM;
pl061->base = devm_ioremap_resource(dev, &adev->res);
if (IS_ERR(pl061->base))
return PTR_ERR(pl061->base);
raw_spin_lock_init(&pl061->lock);
pl061->gc.request = gpiochip_generic_request;
pl061->gc.free = gpiochip_generic_free;
pl061->gc.base = -1;
pl061->gc.get_direction = pl061_get_direction;
pl061->gc.direction_input = pl061_direction_input;
pl061->gc.direction_output = pl061_direction_output;
pl061->gc.get = pl061_get_value;
pl061->gc.set = pl061_set_value;
pl061->gc.ngpio = PL061_GPIO_NR;
pl061->gc.label = dev_name(dev);
pl061->gc.parent = dev;
pl061->gc.owner = THIS_MODULE;
/*
* irq_chip support
*/
writeb(0, pl061->base + GPIOIE); /* disable irqs */
irq = adev->irq[0];
if (!irq)
dev_warn(&adev->dev, "IRQ support disabled\n");
pl061->parent_irq = irq;
girq = &pl061->gc.irq;
gpio_irq_chip_set_chip(girq, &pl061_irq_chip);
girq->parent_handler = pl061_irq_handler;
girq->num_parents = 1;
girq->parents = devm_kcalloc(dev, 1, sizeof(*girq->parents),
GFP_KERNEL);
if (!girq->parents)
return -ENOMEM;
girq->parents[0] = irq;
girq->default_type = IRQ_TYPE_NONE;
girq->handler = handle_bad_irq;
ret = devm_gpiochip_add_data(dev, &pl061->gc, pl061);
if (ret)
return ret;
gpio: pl061: move irqdomain initialization The PL061 driver had the irqdomain initialization in an unfortunate place: when used with device tree (and thus passing the base IRQ 0) the driver would work, as this registers an irqdomain and waits for mappings to be done dynamically as the devices request their IRQs, whereas when booting using platform data the irqdomain core would attempt to allocate IRQ descriptors dynamically (which works fine) but also to associate the irq_domain_associate_many() on all IRQs, which in turn will call the mapping function which at this point will try to set the type of the IRQ and then tries to acquire a non-initialized spinlock yielding a backtrace like this: CPU: 0 PID: 1 Comm: swapper Not tainted 3.13.0-rc1+ #652 Backtrace: [<c0016f0c>] (dump_backtrace) from [<c00172ac>] (show_stack+0x18/0x1c) r6:c798ace0 r5:00000000 r4:c78257e0 r3:00200140 [<c0017294>] (show_stack) from [<c0329ea0>] (dump_stack+0x20/0x28) [<c0329e80>] (dump_stack) from [<c004fa80>] (__lock_acquire+0x1c0/0x1b80) [<c004f8c0>] (__lock_acquire) from [<c0051970>] (lock_acquire+0x6c/0x80) r10:00000000 r9:c0455234 r8:00000060 r7:c047d798 r6:600000d3 r5:00000000 r4:c782c000 [<c0051904>] (lock_acquire) from [<c032e484>] (_raw_spin_lock_irqsave+0x60/0x74) r6:c01a1100 r5:800000d3 r4:c798acd0 [<c032e424>] (_raw_spin_lock_irqsave) from [<c01a1100>] (pl061_irq_type+0x28/0x) r6:00000000 r5:00000000 r4:c798acd0 [<c01a10d8>] (pl061_irq_type) from [<c0059ef4>] (__irq_set_trigger+0x70/0x104) r6:00000000 r5:c01a10d8 r4:c046da1c r3:c01a10d8 [<c0059e84>] (__irq_set_trigger) from [<c005b348>] (irq_set_irq_type+0x40/0x60) r10:c043240c r8:00000060 r7:00000000 r6:c046da1c r5:00000060 r4:00000000 [<c005b308>] (irq_set_irq_type) from [<c01a1208>] (pl061_irq_map+0x40/0x54) r6:c79693c0 r5:c798acd0 r4:00000060 [<c01a11c8>] (pl061_irq_map) from [<c005d27c>] (irq_domain_associate+0xc0/0x190) r5:00000060 r4:c046da1c [<c005d1bc>] (irq_domain_associate) from [<c005d604>] (irq_domain_associate_man) r8:00000008 r7:00000000 r6:c79693c0 r5:00000060 r4:00000000 [<c005d5d0>] (irq_domain_associate_many) from [<c005d864>] (irq_domain_add_simp) r8:c046578c r7:c035b72c r6:c79693c0 r5:00000060 r4:00000008 r3:00000008 [<c005d814>] (irq_domain_add_simple) from [<c01a1380>] (pl061_probe+0xc4/0x22c) r6:00000060 r5:c0464380 r4:c798acd0 [<c01a12bc>] (pl061_probe) from [<c01c0450>] (amba_probe+0x74/0xe0) r10:c043240c r9:c0455234 r8:00000000 r7:c047d7f8 r6:c047d744 r5:00000000 r4:c0464380 This moves the irqdomain initialization to a point where the spinlock and GPIO chip are both fully propulated, so the callbacks can be used without crashes. I had some problem reproducing the crash, as the devm_kzalloc():ed zeroed memory would seemingly mask the spinlock as something OK, but by poisoning the lock like this: u32 *dum; dum = (u32 *) &chip->lock; *dum = 0xaaaaaaaaU; I could reproduce, fix and test the patch. Reported-by: Russell King <linux@arm.linux.org.uk> Cc: Rob Herring <robherring2@gmail.com> Cc: Haojian Zhuang <haojian.zhuang@linaro.org> Cc: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-27 15:47:02 +08:00
amba_set_drvdata(adev, pl061);
dev_info(dev, "PL061 GPIO chip registered\n");
return 0;
}
#ifdef CONFIG_PM
static int pl061_suspend(struct device *dev)
{
struct pl061 *pl061 = dev_get_drvdata(dev);
int offset;
pl061->csave_regs.gpio_data = 0;
pl061->csave_regs.gpio_dir = readb(pl061->base + GPIODIR);
pl061->csave_regs.gpio_is = readb(pl061->base + GPIOIS);
pl061->csave_regs.gpio_ibe = readb(pl061->base + GPIOIBE);
pl061->csave_regs.gpio_iev = readb(pl061->base + GPIOIEV);
pl061->csave_regs.gpio_ie = readb(pl061->base + GPIOIE);
for (offset = 0; offset < PL061_GPIO_NR; offset++) {
if (pl061->csave_regs.gpio_dir & (BIT(offset)))
pl061->csave_regs.gpio_data |=
pl061_get_value(&pl061->gc, offset) << offset;
}
return 0;
}
static int pl061_resume(struct device *dev)
{
struct pl061 *pl061 = dev_get_drvdata(dev);
int offset;
for (offset = 0; offset < PL061_GPIO_NR; offset++) {
if (pl061->csave_regs.gpio_dir & (BIT(offset)))
pl061_direction_output(&pl061->gc, offset,
pl061->csave_regs.gpio_data &
(BIT(offset)));
else
pl061_direction_input(&pl061->gc, offset);
}
writeb(pl061->csave_regs.gpio_is, pl061->base + GPIOIS);
writeb(pl061->csave_regs.gpio_ibe, pl061->base + GPIOIBE);
writeb(pl061->csave_regs.gpio_iev, pl061->base + GPIOIEV);
writeb(pl061->csave_regs.gpio_ie, pl061->base + GPIOIE);
return 0;
}
static const struct dev_pm_ops pl061_dev_pm_ops = {
.suspend = pl061_suspend,
.resume = pl061_resume,
.freeze = pl061_suspend,
.restore = pl061_resume,
};
#endif
static const struct amba_id pl061_ids[] = {
{
.id = 0x00041061,
.mask = 0x000fffff,
},
{ 0, 0 },
};
MODULE_DEVICE_TABLE(amba, pl061_ids);
static struct amba_driver pl061_gpio_driver = {
.drv = {
.name = "pl061_gpio",
#ifdef CONFIG_PM
.pm = &pl061_dev_pm_ops,
#endif
},
.id_table = pl061_ids,
.probe = pl061_probe,
};
module_amba_driver(pl061_gpio_driver);
MODULE_LICENSE("GPL v2");