OpenCloudOS-Kernel/drivers/net/ethernet/marvell/mvneta.c

2849 lines
75 KiB
C
Raw Normal View History

net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
/*
* Driver for Marvell NETA network card for Armada XP and Armada 370 SoCs.
*
* Copyright (C) 2012 Marvell
*
* Rami Rosen <rosenr@marvell.com>
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/version.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/platform_device.h>
#include <linux/skbuff.h>
#include <linux/inetdevice.h>
#include <linux/mbus.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <net/ip.h>
#include <net/ipv6.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include <linux/of_address.h>
#include <linux/phy.h>
#include <linux/clk.h>
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
/* Registers */
#define MVNETA_RXQ_CONFIG_REG(q) (0x1400 + ((q) << 2))
#define MVNETA_RXQ_HW_BUF_ALLOC BIT(1)
#define MVNETA_RXQ_PKT_OFFSET_ALL_MASK (0xf << 8)
#define MVNETA_RXQ_PKT_OFFSET_MASK(offs) ((offs) << 8)
#define MVNETA_RXQ_THRESHOLD_REG(q) (0x14c0 + ((q) << 2))
#define MVNETA_RXQ_NON_OCCUPIED(v) ((v) << 16)
#define MVNETA_RXQ_BASE_ADDR_REG(q) (0x1480 + ((q) << 2))
#define MVNETA_RXQ_SIZE_REG(q) (0x14a0 + ((q) << 2))
#define MVNETA_RXQ_BUF_SIZE_SHIFT 19
#define MVNETA_RXQ_BUF_SIZE_MASK (0x1fff << 19)
#define MVNETA_RXQ_STATUS_REG(q) (0x14e0 + ((q) << 2))
#define MVNETA_RXQ_OCCUPIED_ALL_MASK 0x3fff
#define MVNETA_RXQ_STATUS_UPDATE_REG(q) (0x1500 + ((q) << 2))
#define MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT 16
#define MVNETA_RXQ_ADD_NON_OCCUPIED_MAX 255
#define MVNETA_PORT_RX_RESET 0x1cc0
#define MVNETA_PORT_RX_DMA_RESET BIT(0)
#define MVNETA_PHY_ADDR 0x2000
#define MVNETA_PHY_ADDR_MASK 0x1f
#define MVNETA_MBUS_RETRY 0x2010
#define MVNETA_UNIT_INTR_CAUSE 0x2080
#define MVNETA_UNIT_CONTROL 0x20B0
#define MVNETA_PHY_POLLING_ENABLE BIT(1)
#define MVNETA_WIN_BASE(w) (0x2200 + ((w) << 3))
#define MVNETA_WIN_SIZE(w) (0x2204 + ((w) << 3))
#define MVNETA_WIN_REMAP(w) (0x2280 + ((w) << 2))
#define MVNETA_BASE_ADDR_ENABLE 0x2290
#define MVNETA_PORT_CONFIG 0x2400
#define MVNETA_UNI_PROMISC_MODE BIT(0)
#define MVNETA_DEF_RXQ(q) ((q) << 1)
#define MVNETA_DEF_RXQ_ARP(q) ((q) << 4)
#define MVNETA_TX_UNSET_ERR_SUM BIT(12)
#define MVNETA_DEF_RXQ_TCP(q) ((q) << 16)
#define MVNETA_DEF_RXQ_UDP(q) ((q) << 19)
#define MVNETA_DEF_RXQ_BPDU(q) ((q) << 22)
#define MVNETA_RX_CSUM_WITH_PSEUDO_HDR BIT(25)
#define MVNETA_PORT_CONFIG_DEFL_VALUE(q) (MVNETA_DEF_RXQ(q) | \
MVNETA_DEF_RXQ_ARP(q) | \
MVNETA_DEF_RXQ_TCP(q) | \
MVNETA_DEF_RXQ_UDP(q) | \
MVNETA_DEF_RXQ_BPDU(q) | \
MVNETA_TX_UNSET_ERR_SUM | \
MVNETA_RX_CSUM_WITH_PSEUDO_HDR)
#define MVNETA_PORT_CONFIG_EXTEND 0x2404
#define MVNETA_MAC_ADDR_LOW 0x2414
#define MVNETA_MAC_ADDR_HIGH 0x2418
#define MVNETA_SDMA_CONFIG 0x241c
#define MVNETA_SDMA_BRST_SIZE_16 4
#define MVNETA_NO_DESC_SWAP 0x0
#define MVNETA_RX_BRST_SZ_MASK(burst) ((burst) << 1)
#define MVNETA_RX_NO_DATA_SWAP BIT(4)
#define MVNETA_TX_NO_DATA_SWAP BIT(5)
#define MVNETA_TX_BRST_SZ_MASK(burst) ((burst) << 22)
#define MVNETA_PORT_STATUS 0x2444
#define MVNETA_TX_IN_PRGRS BIT(1)
#define MVNETA_TX_FIFO_EMPTY BIT(8)
#define MVNETA_RX_MIN_FRAME_SIZE 0x247c
#define MVNETA_TYPE_PRIO 0x24bc
#define MVNETA_FORCE_UNI BIT(21)
#define MVNETA_TXQ_CMD_1 0x24e4
#define MVNETA_TXQ_CMD 0x2448
#define MVNETA_TXQ_DISABLE_SHIFT 8
#define MVNETA_TXQ_ENABLE_MASK 0x000000ff
#define MVNETA_ACC_MODE 0x2500
#define MVNETA_CPU_MAP(cpu) (0x2540 + ((cpu) << 2))
#define MVNETA_CPU_RXQ_ACCESS_ALL_MASK 0x000000ff
#define MVNETA_CPU_TXQ_ACCESS_ALL_MASK 0x0000ff00
#define MVNETA_RXQ_TIME_COAL_REG(q) (0x2580 + ((q) << 2))
#define MVNETA_INTR_NEW_CAUSE 0x25a0
#define MVNETA_RX_INTR_MASK(nr_rxqs) (((1 << nr_rxqs) - 1) << 8)
#define MVNETA_INTR_NEW_MASK 0x25a4
#define MVNETA_INTR_OLD_CAUSE 0x25a8
#define MVNETA_INTR_OLD_MASK 0x25ac
#define MVNETA_INTR_MISC_CAUSE 0x25b0
#define MVNETA_INTR_MISC_MASK 0x25b4
#define MVNETA_INTR_ENABLE 0x25b8
#define MVNETA_TXQ_INTR_ENABLE_ALL_MASK 0x0000ff00
#define MVNETA_RXQ_INTR_ENABLE_ALL_MASK 0xff000000
#define MVNETA_RXQ_CMD 0x2680
#define MVNETA_RXQ_DISABLE_SHIFT 8
#define MVNETA_RXQ_ENABLE_MASK 0x000000ff
#define MVETH_TXQ_TOKEN_COUNT_REG(q) (0x2700 + ((q) << 4))
#define MVETH_TXQ_TOKEN_CFG_REG(q) (0x2704 + ((q) << 4))
#define MVNETA_GMAC_CTRL_0 0x2c00
#define MVNETA_GMAC_MAX_RX_SIZE_SHIFT 2
#define MVNETA_GMAC_MAX_RX_SIZE_MASK 0x7ffc
#define MVNETA_GMAC0_PORT_ENABLE BIT(0)
#define MVNETA_GMAC_CTRL_2 0x2c08
#define MVNETA_GMAC2_PSC_ENABLE BIT(3)
#define MVNETA_GMAC2_PORT_RGMII BIT(4)
#define MVNETA_GMAC2_PORT_RESET BIT(6)
#define MVNETA_GMAC_STATUS 0x2c10
#define MVNETA_GMAC_LINK_UP BIT(0)
#define MVNETA_GMAC_SPEED_1000 BIT(1)
#define MVNETA_GMAC_SPEED_100 BIT(2)
#define MVNETA_GMAC_FULL_DUPLEX BIT(3)
#define MVNETA_GMAC_RX_FLOW_CTRL_ENABLE BIT(4)
#define MVNETA_GMAC_TX_FLOW_CTRL_ENABLE BIT(5)
#define MVNETA_GMAC_RX_FLOW_CTRL_ACTIVE BIT(6)
#define MVNETA_GMAC_TX_FLOW_CTRL_ACTIVE BIT(7)
#define MVNETA_GMAC_AUTONEG_CONFIG 0x2c0c
#define MVNETA_GMAC_FORCE_LINK_DOWN BIT(0)
#define MVNETA_GMAC_FORCE_LINK_PASS BIT(1)
#define MVNETA_GMAC_CONFIG_MII_SPEED BIT(5)
#define MVNETA_GMAC_CONFIG_GMII_SPEED BIT(6)
#define MVNETA_GMAC_CONFIG_FULL_DUPLEX BIT(12)
#define MVNETA_MIB_COUNTERS_BASE 0x3080
#define MVNETA_MIB_LATE_COLLISION 0x7c
#define MVNETA_DA_FILT_SPEC_MCAST 0x3400
#define MVNETA_DA_FILT_OTH_MCAST 0x3500
#define MVNETA_DA_FILT_UCAST_BASE 0x3600
#define MVNETA_TXQ_BASE_ADDR_REG(q) (0x3c00 + ((q) << 2))
#define MVNETA_TXQ_SIZE_REG(q) (0x3c20 + ((q) << 2))
#define MVNETA_TXQ_SENT_THRESH_ALL_MASK 0x3fff0000
#define MVNETA_TXQ_SENT_THRESH_MASK(coal) ((coal) << 16)
#define MVNETA_TXQ_UPDATE_REG(q) (0x3c60 + ((q) << 2))
#define MVNETA_TXQ_DEC_SENT_SHIFT 16
#define MVNETA_TXQ_STATUS_REG(q) (0x3c40 + ((q) << 2))
#define MVNETA_TXQ_SENT_DESC_SHIFT 16
#define MVNETA_TXQ_SENT_DESC_MASK 0x3fff0000
#define MVNETA_PORT_TX_RESET 0x3cf0
#define MVNETA_PORT_TX_DMA_RESET BIT(0)
#define MVNETA_TX_MTU 0x3e0c
#define MVNETA_TX_TOKEN_SIZE 0x3e14
#define MVNETA_TX_TOKEN_SIZE_MAX 0xffffffff
#define MVNETA_TXQ_TOKEN_SIZE_REG(q) (0x3e40 + ((q) << 2))
#define MVNETA_TXQ_TOKEN_SIZE_MAX 0x7fffffff
#define MVNETA_CAUSE_TXQ_SENT_DESC_ALL_MASK 0xff
/* Descriptor ring Macros */
#define MVNETA_QUEUE_NEXT_DESC(q, index) \
(((index) < (q)->last_desc) ? ((index) + 1) : 0)
/* Various constants */
/* Coalescing */
#define MVNETA_TXDONE_COAL_PKTS 16
#define MVNETA_RX_COAL_PKTS 32
#define MVNETA_RX_COAL_USEC 100
/* Timer */
#define MVNETA_TX_DONE_TIMER_PERIOD 10
/* Napi polling weight */
#define MVNETA_RX_POLL_WEIGHT 64
/* The two bytes Marvell header. Either contains a special value used
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* by Marvell switches when a specific hardware mode is enabled (not
* supported by this driver) or is filled automatically by zeroes on
* the RX side. Those two bytes being at the front of the Ethernet
* header, they allow to have the IP header aligned on a 4 bytes
* boundary automatically: the hardware skips those two bytes on its
* own.
*/
#define MVNETA_MH_SIZE 2
#define MVNETA_VLAN_TAG_LEN 4
#define MVNETA_CPU_D_CACHE_LINE_SIZE 32
#define MVNETA_TX_CSUM_MAX_SIZE 9800
#define MVNETA_ACC_MODE_EXT 1
/* Timeout constants */
#define MVNETA_TX_DISABLE_TIMEOUT_MSEC 1000
#define MVNETA_RX_DISABLE_TIMEOUT_MSEC 1000
#define MVNETA_TX_FIFO_EMPTY_TIMEOUT 10000
#define MVNETA_TX_MTU_MAX 0x3ffff
/* Max number of Rx descriptors */
#define MVNETA_MAX_RXD 128
/* Max number of Tx descriptors */
#define MVNETA_MAX_TXD 532
/* descriptor aligned size */
#define MVNETA_DESC_ALIGNED_SIZE 32
#define MVNETA_RX_PKT_SIZE(mtu) \
ALIGN((mtu) + MVNETA_MH_SIZE + MVNETA_VLAN_TAG_LEN + \
ETH_HLEN + ETH_FCS_LEN, \
MVNETA_CPU_D_CACHE_LINE_SIZE)
#define MVNETA_RX_BUF_SIZE(pkt_size) ((pkt_size) + NET_SKB_PAD)
struct mvneta_stats {
struct u64_stats_sync syncp;
u64 packets;
u64 bytes;
};
struct mvneta_port {
int pkt_size;
void __iomem *base;
struct mvneta_rx_queue *rxqs;
struct mvneta_tx_queue *txqs;
struct timer_list tx_done_timer;
struct net_device *dev;
u32 cause_rx_tx;
struct napi_struct napi;
/* Flags */
unsigned long flags;
#define MVNETA_F_TX_DONE_TIMER_BIT 0
/* Napi weight */
int weight;
/* Core clock */
struct clk *clk;
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
u8 mcast_count[256];
u16 tx_ring_size;
u16 rx_ring_size;
struct mvneta_stats tx_stats;
struct mvneta_stats rx_stats;
struct mii_bus *mii_bus;
struct phy_device *phy_dev;
phy_interface_t phy_interface;
struct device_node *phy_node;
unsigned int link;
unsigned int duplex;
unsigned int speed;
};
/* The mvneta_tx_desc and mvneta_rx_desc structures describe the
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* layout of the transmit and reception DMA descriptors, and their
* layout is therefore defined by the hardware design
*/
struct mvneta_tx_desc {
u32 command; /* Options used by HW for packet transmitting.*/
#define MVNETA_TX_L3_OFF_SHIFT 0
#define MVNETA_TX_IP_HLEN_SHIFT 8
#define MVNETA_TX_L4_UDP BIT(16)
#define MVNETA_TX_L3_IP6 BIT(17)
#define MVNETA_TXD_IP_CSUM BIT(18)
#define MVNETA_TXD_Z_PAD BIT(19)
#define MVNETA_TXD_L_DESC BIT(20)
#define MVNETA_TXD_F_DESC BIT(21)
#define MVNETA_TXD_FLZ_DESC (MVNETA_TXD_Z_PAD | \
MVNETA_TXD_L_DESC | \
MVNETA_TXD_F_DESC)
#define MVNETA_TX_L4_CSUM_FULL BIT(30)
#define MVNETA_TX_L4_CSUM_NOT BIT(31)
u16 reserverd1; /* csum_l4 (for future use) */
u16 data_size; /* Data size of transmitted packet in bytes */
u32 buf_phys_addr; /* Physical addr of transmitted buffer */
u32 reserved2; /* hw_cmd - (for future use, PMT) */
u32 reserved3[4]; /* Reserved - (for future use) */
};
struct mvneta_rx_desc {
u32 status; /* Info about received packet */
#define MVNETA_RXD_ERR_CRC 0x0
#define MVNETA_RXD_ERR_SUMMARY BIT(16)
#define MVNETA_RXD_ERR_OVERRUN BIT(17)
#define MVNETA_RXD_ERR_LEN BIT(18)
#define MVNETA_RXD_ERR_RESOURCE (BIT(17) | BIT(18))
#define MVNETA_RXD_ERR_CODE_MASK (BIT(17) | BIT(18))
#define MVNETA_RXD_L3_IP4 BIT(25)
#define MVNETA_RXD_FIRST_LAST_DESC (BIT(26) | BIT(27))
#define MVNETA_RXD_L4_CSUM_OK BIT(30)
u16 reserved1; /* pnc_info - (for future use, PnC) */
u16 data_size; /* Size of received packet in bytes */
u32 buf_phys_addr; /* Physical address of the buffer */
u32 reserved2; /* pnc_flow_id (for future use, PnC) */
u32 buf_cookie; /* cookie for access to RX buffer in rx path */
u16 reserved3; /* prefetch_cmd, for future use */
u16 reserved4; /* csum_l4 - (for future use, PnC) */
u32 reserved5; /* pnc_extra PnC (for future use, PnC) */
u32 reserved6; /* hw_cmd (for future use, PnC and HWF) */
};
struct mvneta_tx_queue {
/* Number of this TX queue, in the range 0-7 */
u8 id;
/* Number of TX DMA descriptors in the descriptor ring */
int size;
/* Number of currently used TX DMA descriptor in the
* descriptor ring
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
int count;
/* Array of transmitted skb */
struct sk_buff **tx_skb;
/* Index of last TX DMA descriptor that was inserted */
int txq_put_index;
/* Index of the TX DMA descriptor to be cleaned up */
int txq_get_index;
u32 done_pkts_coal;
/* Virtual address of the TX DMA descriptors array */
struct mvneta_tx_desc *descs;
/* DMA address of the TX DMA descriptors array */
dma_addr_t descs_phys;
/* Index of the last TX DMA descriptor */
int last_desc;
/* Index of the next TX DMA descriptor to process */
int next_desc_to_proc;
};
struct mvneta_rx_queue {
/* rx queue number, in the range 0-7 */
u8 id;
/* num of rx descriptors in the rx descriptor ring */
int size;
/* counter of times when mvneta_refill() failed */
int missed;
u32 pkts_coal;
u32 time_coal;
/* Virtual address of the RX DMA descriptors array */
struct mvneta_rx_desc *descs;
/* DMA address of the RX DMA descriptors array */
dma_addr_t descs_phys;
/* Index of the last RX DMA descriptor */
int last_desc;
/* Index of the next RX DMA descriptor to process */
int next_desc_to_proc;
};
static int rxq_number = 8;
static int txq_number = 8;
static int rxq_def;
static int txq_def;
#define MVNETA_DRIVER_NAME "mvneta"
#define MVNETA_DRIVER_VERSION "1.0"
/* Utility/helper methods */
/* Write helper method */
static void mvreg_write(struct mvneta_port *pp, u32 offset, u32 data)
{
writel(data, pp->base + offset);
}
/* Read helper method */
static u32 mvreg_read(struct mvneta_port *pp, u32 offset)
{
return readl(pp->base + offset);
}
/* Increment txq get counter */
static void mvneta_txq_inc_get(struct mvneta_tx_queue *txq)
{
txq->txq_get_index++;
if (txq->txq_get_index == txq->size)
txq->txq_get_index = 0;
}
/* Increment txq put counter */
static void mvneta_txq_inc_put(struct mvneta_tx_queue *txq)
{
txq->txq_put_index++;
if (txq->txq_put_index == txq->size)
txq->txq_put_index = 0;
}
/* Clear all MIB counters */
static void mvneta_mib_counters_clear(struct mvneta_port *pp)
{
int i;
u32 dummy;
/* Perform dummy reads from MIB counters */
for (i = 0; i < MVNETA_MIB_LATE_COLLISION; i += 4)
dummy = mvreg_read(pp, (MVNETA_MIB_COUNTERS_BASE + i));
}
/* Get System Network Statistics */
struct rtnl_link_stats64 *mvneta_get_stats64(struct net_device *dev,
struct rtnl_link_stats64 *stats)
{
struct mvneta_port *pp = netdev_priv(dev);
unsigned int start;
memset(stats, 0, sizeof(struct rtnl_link_stats64));
do {
start = u64_stats_fetch_begin_bh(&pp->rx_stats.syncp);
stats->rx_packets = pp->rx_stats.packets;
stats->rx_bytes = pp->rx_stats.bytes;
} while (u64_stats_fetch_retry_bh(&pp->rx_stats.syncp, start));
do {
start = u64_stats_fetch_begin_bh(&pp->tx_stats.syncp);
stats->tx_packets = pp->tx_stats.packets;
stats->tx_bytes = pp->tx_stats.bytes;
} while (u64_stats_fetch_retry_bh(&pp->tx_stats.syncp, start));
stats->rx_errors = dev->stats.rx_errors;
stats->rx_dropped = dev->stats.rx_dropped;
stats->tx_dropped = dev->stats.tx_dropped;
return stats;
}
/* Rx descriptors helper methods */
/* Checks whether the given RX descriptor is both the first and the
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* last descriptor for the RX packet. Each RX packet is currently
* received through a single RX descriptor, so not having each RX
* descriptor with its first and last bits set is an error
*/
static int mvneta_rxq_desc_is_first_last(struct mvneta_rx_desc *desc)
{
return (desc->status & MVNETA_RXD_FIRST_LAST_DESC) ==
MVNETA_RXD_FIRST_LAST_DESC;
}
/* Add number of descriptors ready to receive new packets */
static void mvneta_rxq_non_occup_desc_add(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq,
int ndescs)
{
/* Only MVNETA_RXQ_ADD_NON_OCCUPIED_MAX (255) descriptors can
* be added at once
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
while (ndescs > MVNETA_RXQ_ADD_NON_OCCUPIED_MAX) {
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id),
(MVNETA_RXQ_ADD_NON_OCCUPIED_MAX <<
MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT));
ndescs -= MVNETA_RXQ_ADD_NON_OCCUPIED_MAX;
}
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id),
(ndescs << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT));
}
/* Get number of RX descriptors occupied by received packets */
static int mvneta_rxq_busy_desc_num_get(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
u32 val;
val = mvreg_read(pp, MVNETA_RXQ_STATUS_REG(rxq->id));
return val & MVNETA_RXQ_OCCUPIED_ALL_MASK;
}
/* Update num of rx desc called upon return from rx path or
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* from mvneta_rxq_drop_pkts().
*/
static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq,
int rx_done, int rx_filled)
{
u32 val;
if ((rx_done <= 0xff) && (rx_filled <= 0xff)) {
val = rx_done |
(rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT);
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val);
return;
}
/* Only 255 descriptors can be added at once */
while ((rx_done > 0) || (rx_filled > 0)) {
if (rx_done <= 0xff) {
val = rx_done;
rx_done = 0;
} else {
val = 0xff;
rx_done -= 0xff;
}
if (rx_filled <= 0xff) {
val |= rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT;
rx_filled = 0;
} else {
val |= 0xff << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT;
rx_filled -= 0xff;
}
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val);
}
}
/* Get pointer to next RX descriptor to be processed by SW */
static struct mvneta_rx_desc *
mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
{
int rx_desc = rxq->next_desc_to_proc;
rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
return rxq->descs + rx_desc;
}
/* Change maximum receive size of the port. */
static void mvneta_max_rx_size_set(struct mvneta_port *pp, int max_rx_size)
{
u32 val;
val = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
val &= ~MVNETA_GMAC_MAX_RX_SIZE_MASK;
val |= ((max_rx_size - MVNETA_MH_SIZE) / 2) <<
MVNETA_GMAC_MAX_RX_SIZE_SHIFT;
mvreg_write(pp, MVNETA_GMAC_CTRL_0, val);
}
/* Set rx queue offset */
static void mvneta_rxq_offset_set(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq,
int offset)
{
u32 val;
val = mvreg_read(pp, MVNETA_RXQ_CONFIG_REG(rxq->id));
val &= ~MVNETA_RXQ_PKT_OFFSET_ALL_MASK;
/* Offset is in */
val |= MVNETA_RXQ_PKT_OFFSET_MASK(offset >> 3);
mvreg_write(pp, MVNETA_RXQ_CONFIG_REG(rxq->id), val);
}
/* Tx descriptors helper methods */
/* Update HW with number of TX descriptors to be sent */
static void mvneta_txq_pend_desc_add(struct mvneta_port *pp,
struct mvneta_tx_queue *txq,
int pend_desc)
{
u32 val;
/* Only 255 descriptors can be added at once ; Assume caller
* process TX desriptors in quanta less than 256
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
val = pend_desc;
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
}
/* Get pointer to next TX descriptor to be processed (send) by HW */
static struct mvneta_tx_desc *
mvneta_txq_next_desc_get(struct mvneta_tx_queue *txq)
{
int tx_desc = txq->next_desc_to_proc;
txq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(txq, tx_desc);
return txq->descs + tx_desc;
}
/* Release the last allocated TX descriptor. Useful to handle DMA
* mapping failures in the TX path.
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
static void mvneta_txq_desc_put(struct mvneta_tx_queue *txq)
{
if (txq->next_desc_to_proc == 0)
txq->next_desc_to_proc = txq->last_desc - 1;
else
txq->next_desc_to_proc--;
}
/* Set rxq buf size */
static void mvneta_rxq_buf_size_set(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq,
int buf_size)
{
u32 val;
val = mvreg_read(pp, MVNETA_RXQ_SIZE_REG(rxq->id));
val &= ~MVNETA_RXQ_BUF_SIZE_MASK;
val |= ((buf_size >> 3) << MVNETA_RXQ_BUF_SIZE_SHIFT);
mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), val);
}
/* Disable buffer management (BM) */
static void mvneta_rxq_bm_disable(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
u32 val;
val = mvreg_read(pp, MVNETA_RXQ_CONFIG_REG(rxq->id));
val &= ~MVNETA_RXQ_HW_BUF_ALLOC;
mvreg_write(pp, MVNETA_RXQ_CONFIG_REG(rxq->id), val);
}
/* Sets the RGMII Enable bit (RGMIIEn) in port MAC control register */
static void __devinit mvneta_gmac_rgmii_set(struct mvneta_port *pp, int enable)
{
u32 val;
val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
if (enable)
val |= MVNETA_GMAC2_PORT_RGMII;
else
val &= ~MVNETA_GMAC2_PORT_RGMII;
mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
}
/* Config SGMII port */
static void __devinit mvneta_port_sgmii_config(struct mvneta_port *pp)
{
u32 val;
val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
val |= MVNETA_GMAC2_PSC_ENABLE;
mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
}
/* Start the Ethernet port RX and TX activity */
static void mvneta_port_up(struct mvneta_port *pp)
{
int queue;
u32 q_map;
/* Enable all initialized TXs. */
mvneta_mib_counters_clear(pp);
q_map = 0;
for (queue = 0; queue < txq_number; queue++) {
struct mvneta_tx_queue *txq = &pp->txqs[queue];
if (txq->descs != NULL)
q_map |= (1 << queue);
}
mvreg_write(pp, MVNETA_TXQ_CMD, q_map);
/* Enable all initialized RXQs. */
q_map = 0;
for (queue = 0; queue < rxq_number; queue++) {
struct mvneta_rx_queue *rxq = &pp->rxqs[queue];
if (rxq->descs != NULL)
q_map |= (1 << queue);
}
mvreg_write(pp, MVNETA_RXQ_CMD, q_map);
}
/* Stop the Ethernet port activity */
static void mvneta_port_down(struct mvneta_port *pp)
{
u32 val;
int count;
/* Stop Rx port activity. Check port Rx activity. */
val = mvreg_read(pp, MVNETA_RXQ_CMD) & MVNETA_RXQ_ENABLE_MASK;
/* Issue stop command for active channels only */
if (val != 0)
mvreg_write(pp, MVNETA_RXQ_CMD,
val << MVNETA_RXQ_DISABLE_SHIFT);
/* Wait for all Rx activity to terminate. */
count = 0;
do {
if (count++ >= MVNETA_RX_DISABLE_TIMEOUT_MSEC) {
netdev_warn(pp->dev,
"TIMEOUT for RX stopped ! rx_queue_cmd: 0x08%x\n",
val);
break;
}
mdelay(1);
val = mvreg_read(pp, MVNETA_RXQ_CMD);
} while (val & 0xff);
/* Stop Tx port activity. Check port Tx activity. Issue stop
* command for active channels only
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
val = (mvreg_read(pp, MVNETA_TXQ_CMD)) & MVNETA_TXQ_ENABLE_MASK;
if (val != 0)
mvreg_write(pp, MVNETA_TXQ_CMD,
(val << MVNETA_TXQ_DISABLE_SHIFT));
/* Wait for all Tx activity to terminate. */
count = 0;
do {
if (count++ >= MVNETA_TX_DISABLE_TIMEOUT_MSEC) {
netdev_warn(pp->dev,
"TIMEOUT for TX stopped status=0x%08x\n",
val);
break;
}
mdelay(1);
/* Check TX Command reg that all Txqs are stopped */
val = mvreg_read(pp, MVNETA_TXQ_CMD);
} while (val & 0xff);
/* Double check to verify that TX FIFO is empty */
count = 0;
do {
if (count++ >= MVNETA_TX_FIFO_EMPTY_TIMEOUT) {
netdev_warn(pp->dev,
"TX FIFO empty timeout status=0x08%x\n",
val);
break;
}
mdelay(1);
val = mvreg_read(pp, MVNETA_PORT_STATUS);
} while (!(val & MVNETA_TX_FIFO_EMPTY) &&
(val & MVNETA_TX_IN_PRGRS));
udelay(200);
}
/* Enable the port by setting the port enable bit of the MAC control register */
static void mvneta_port_enable(struct mvneta_port *pp)
{
u32 val;
/* Enable port */
val = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
val |= MVNETA_GMAC0_PORT_ENABLE;
mvreg_write(pp, MVNETA_GMAC_CTRL_0, val);
}
/* Disable the port and wait for about 200 usec before retuning */
static void mvneta_port_disable(struct mvneta_port *pp)
{
u32 val;
/* Reset the Enable bit in the Serial Control Register */
val = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
val &= ~MVNETA_GMAC0_PORT_ENABLE;
mvreg_write(pp, MVNETA_GMAC_CTRL_0, val);
udelay(200);
}
/* Multicast tables methods */
/* Set all entries in Unicast MAC Table; queue==-1 means reject all */
static void mvneta_set_ucast_table(struct mvneta_port *pp, int queue)
{
int offset;
u32 val;
if (queue == -1) {
val = 0;
} else {
val = 0x1 | (queue << 1);
val |= (val << 24) | (val << 16) | (val << 8);
}
for (offset = 0; offset <= 0xc; offset += 4)
mvreg_write(pp, MVNETA_DA_FILT_UCAST_BASE + offset, val);
}
/* Set all entries in Special Multicast MAC Table; queue==-1 means reject all */
static void mvneta_set_special_mcast_table(struct mvneta_port *pp, int queue)
{
int offset;
u32 val;
if (queue == -1) {
val = 0;
} else {
val = 0x1 | (queue << 1);
val |= (val << 24) | (val << 16) | (val << 8);
}
for (offset = 0; offset <= 0xfc; offset += 4)
mvreg_write(pp, MVNETA_DA_FILT_SPEC_MCAST + offset, val);
}
/* Set all entries in Other Multicast MAC Table. queue==-1 means reject all */
static void mvneta_set_other_mcast_table(struct mvneta_port *pp, int queue)
{
int offset;
u32 val;
if (queue == -1) {
memset(pp->mcast_count, 0, sizeof(pp->mcast_count));
val = 0;
} else {
memset(pp->mcast_count, 1, sizeof(pp->mcast_count));
val = 0x1 | (queue << 1);
val |= (val << 24) | (val << 16) | (val << 8);
}
for (offset = 0; offset <= 0xfc; offset += 4)
mvreg_write(pp, MVNETA_DA_FILT_OTH_MCAST + offset, val);
}
/* This method sets defaults to the NETA port:
* Clears interrupt Cause and Mask registers.
* Clears all MAC tables.
* Sets defaults to all registers.
* Resets RX and TX descriptor rings.
* Resets PHY.
* This method can be called after mvneta_port_down() to return the port
* settings to defaults.
*/
static void mvneta_defaults_set(struct mvneta_port *pp)
{
int cpu;
int queue;
u32 val;
/* Clear all Cause registers */
mvreg_write(pp, MVNETA_INTR_NEW_CAUSE, 0);
mvreg_write(pp, MVNETA_INTR_OLD_CAUSE, 0);
mvreg_write(pp, MVNETA_INTR_MISC_CAUSE, 0);
/* Mask all interrupts */
mvreg_write(pp, MVNETA_INTR_NEW_MASK, 0);
mvreg_write(pp, MVNETA_INTR_OLD_MASK, 0);
mvreg_write(pp, MVNETA_INTR_MISC_MASK, 0);
mvreg_write(pp, MVNETA_INTR_ENABLE, 0);
/* Enable MBUS Retry bit16 */
mvreg_write(pp, MVNETA_MBUS_RETRY, 0x20);
/* Set CPU queue access map - all CPUs have access to all RX
* queues and to all TX queues
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
for (cpu = 0; cpu < CONFIG_NR_CPUS; cpu++)
mvreg_write(pp, MVNETA_CPU_MAP(cpu),
(MVNETA_CPU_RXQ_ACCESS_ALL_MASK |
MVNETA_CPU_TXQ_ACCESS_ALL_MASK));
/* Reset RX and TX DMAs */
mvreg_write(pp, MVNETA_PORT_RX_RESET, MVNETA_PORT_RX_DMA_RESET);
mvreg_write(pp, MVNETA_PORT_TX_RESET, MVNETA_PORT_TX_DMA_RESET);
/* Disable Legacy WRR, Disable EJP, Release from reset */
mvreg_write(pp, MVNETA_TXQ_CMD_1, 0);
for (queue = 0; queue < txq_number; queue++) {
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(queue), 0);
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(queue), 0);
}
mvreg_write(pp, MVNETA_PORT_TX_RESET, 0);
mvreg_write(pp, MVNETA_PORT_RX_RESET, 0);
/* Set Port Acceleration Mode */
val = MVNETA_ACC_MODE_EXT;
mvreg_write(pp, MVNETA_ACC_MODE, val);
/* Update val of portCfg register accordingly with all RxQueue types */
val = MVNETA_PORT_CONFIG_DEFL_VALUE(rxq_def);
mvreg_write(pp, MVNETA_PORT_CONFIG, val);
val = 0;
mvreg_write(pp, MVNETA_PORT_CONFIG_EXTEND, val);
mvreg_write(pp, MVNETA_RX_MIN_FRAME_SIZE, 64);
/* Build PORT_SDMA_CONFIG_REG */
val = 0;
/* Default burst size */
val |= MVNETA_TX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16);
val |= MVNETA_RX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16);
val |= (MVNETA_RX_NO_DATA_SWAP | MVNETA_TX_NO_DATA_SWAP |
MVNETA_NO_DESC_SWAP);
/* Assign port SDMA configuration */
mvreg_write(pp, MVNETA_SDMA_CONFIG, val);
mvneta_set_ucast_table(pp, -1);
mvneta_set_special_mcast_table(pp, -1);
mvneta_set_other_mcast_table(pp, -1);
/* Set port interrupt enable register - default enable all */
mvreg_write(pp, MVNETA_INTR_ENABLE,
(MVNETA_RXQ_INTR_ENABLE_ALL_MASK
| MVNETA_TXQ_INTR_ENABLE_ALL_MASK));
}
/* Set max sizes for tx queues */
static void mvneta_txq_max_tx_size_set(struct mvneta_port *pp, int max_tx_size)
{
u32 val, size, mtu;
int queue;
mtu = max_tx_size * 8;
if (mtu > MVNETA_TX_MTU_MAX)
mtu = MVNETA_TX_MTU_MAX;
/* Set MTU */
val = mvreg_read(pp, MVNETA_TX_MTU);
val &= ~MVNETA_TX_MTU_MAX;
val |= mtu;
mvreg_write(pp, MVNETA_TX_MTU, val);
/* TX token size and all TXQs token size must be larger that MTU */
val = mvreg_read(pp, MVNETA_TX_TOKEN_SIZE);
size = val & MVNETA_TX_TOKEN_SIZE_MAX;
if (size < mtu) {
size = mtu;
val &= ~MVNETA_TX_TOKEN_SIZE_MAX;
val |= size;
mvreg_write(pp, MVNETA_TX_TOKEN_SIZE, val);
}
for (queue = 0; queue < txq_number; queue++) {
val = mvreg_read(pp, MVNETA_TXQ_TOKEN_SIZE_REG(queue));
size = val & MVNETA_TXQ_TOKEN_SIZE_MAX;
if (size < mtu) {
size = mtu;
val &= ~MVNETA_TXQ_TOKEN_SIZE_MAX;
val |= size;
mvreg_write(pp, MVNETA_TXQ_TOKEN_SIZE_REG(queue), val);
}
}
}
/* Set unicast address */
static void mvneta_set_ucast_addr(struct mvneta_port *pp, u8 last_nibble,
int queue)
{
unsigned int unicast_reg;
unsigned int tbl_offset;
unsigned int reg_offset;
/* Locate the Unicast table entry */
last_nibble = (0xf & last_nibble);
/* offset from unicast tbl base */
tbl_offset = (last_nibble / 4) * 4;
/* offset within the above reg */
reg_offset = last_nibble % 4;
unicast_reg = mvreg_read(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset));
if (queue == -1) {
/* Clear accepts frame bit at specified unicast DA tbl entry */
unicast_reg &= ~(0xff << (8 * reg_offset));
} else {
unicast_reg &= ~(0xff << (8 * reg_offset));
unicast_reg |= ((0x01 | (queue << 1)) << (8 * reg_offset));
}
mvreg_write(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset), unicast_reg);
}
/* Set mac address */
static void mvneta_mac_addr_set(struct mvneta_port *pp, unsigned char *addr,
int queue)
{
unsigned int mac_h;
unsigned int mac_l;
if (queue != -1) {
mac_l = (addr[4] << 8) | (addr[5]);
mac_h = (addr[0] << 24) | (addr[1] << 16) |
(addr[2] << 8) | (addr[3] << 0);
mvreg_write(pp, MVNETA_MAC_ADDR_LOW, mac_l);
mvreg_write(pp, MVNETA_MAC_ADDR_HIGH, mac_h);
}
/* Accept frames of this address */
mvneta_set_ucast_addr(pp, addr[5], queue);
}
/* Set the number of packets that will be received before RX interrupt
* will be generated by HW.
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
*/
static void mvneta_rx_pkts_coal_set(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq, u32 value)
{
mvreg_write(pp, MVNETA_RXQ_THRESHOLD_REG(rxq->id),
value | MVNETA_RXQ_NON_OCCUPIED(0));
rxq->pkts_coal = value;
}
/* Set the time delay in usec before RX interrupt will be generated by
* HW.
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
*/
static void mvneta_rx_time_coal_set(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq, u32 value)
{
u32 val;
unsigned long clk_rate;
clk_rate = clk_get_rate(pp->clk);
val = (clk_rate / 1000000) * value;
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
mvreg_write(pp, MVNETA_RXQ_TIME_COAL_REG(rxq->id), val);
rxq->time_coal = value;
}
/* Set threshold for TX_DONE pkts coalescing */
static void mvneta_tx_done_pkts_coal_set(struct mvneta_port *pp,
struct mvneta_tx_queue *txq, u32 value)
{
u32 val;
val = mvreg_read(pp, MVNETA_TXQ_SIZE_REG(txq->id));
val &= ~MVNETA_TXQ_SENT_THRESH_ALL_MASK;
val |= MVNETA_TXQ_SENT_THRESH_MASK(value);
mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), val);
txq->done_pkts_coal = value;
}
/* Trigger tx done timer in MVNETA_TX_DONE_TIMER_PERIOD msecs */
static void mvneta_add_tx_done_timer(struct mvneta_port *pp)
{
if (test_and_set_bit(MVNETA_F_TX_DONE_TIMER_BIT, &pp->flags) == 0) {
pp->tx_done_timer.expires = jiffies +
msecs_to_jiffies(MVNETA_TX_DONE_TIMER_PERIOD);
add_timer(&pp->tx_done_timer);
}
}
/* Handle rx descriptor fill by setting buf_cookie and buf_phys_addr */
static void mvneta_rx_desc_fill(struct mvneta_rx_desc *rx_desc,
u32 phys_addr, u32 cookie)
{
rx_desc->buf_cookie = cookie;
rx_desc->buf_phys_addr = phys_addr;
}
/* Decrement sent descriptors counter */
static void mvneta_txq_sent_desc_dec(struct mvneta_port *pp,
struct mvneta_tx_queue *txq,
int sent_desc)
{
u32 val;
/* Only 255 TX descriptors can be updated at once */
while (sent_desc > 0xff) {
val = 0xff << MVNETA_TXQ_DEC_SENT_SHIFT;
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
sent_desc = sent_desc - 0xff;
}
val = sent_desc << MVNETA_TXQ_DEC_SENT_SHIFT;
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
}
/* Get number of TX descriptors already sent by HW */
static int mvneta_txq_sent_desc_num_get(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
u32 val;
int sent_desc;
val = mvreg_read(pp, MVNETA_TXQ_STATUS_REG(txq->id));
sent_desc = (val & MVNETA_TXQ_SENT_DESC_MASK) >>
MVNETA_TXQ_SENT_DESC_SHIFT;
return sent_desc;
}
/* Get number of sent descriptors and decrement counter.
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* The number of sent descriptors is returned.
*/
static int mvneta_txq_sent_desc_proc(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
int sent_desc;
/* Get number of sent descriptors */
sent_desc = mvneta_txq_sent_desc_num_get(pp, txq);
/* Decrement sent descriptors counter */
if (sent_desc)
mvneta_txq_sent_desc_dec(pp, txq, sent_desc);
return sent_desc;
}
/* Set TXQ descriptors fields relevant for CSUM calculation */
static u32 mvneta_txq_desc_csum(int l3_offs, int l3_proto,
int ip_hdr_len, int l4_proto)
{
u32 command;
/* Fields: L3_offset, IP_hdrlen, L3_type, G_IPv4_chk,
* G_L4_chk, L4_type; required only for checksum
* calculation
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
command = l3_offs << MVNETA_TX_L3_OFF_SHIFT;
command |= ip_hdr_len << MVNETA_TX_IP_HLEN_SHIFT;
if (l3_proto == swab16(ETH_P_IP))
command |= MVNETA_TXD_IP_CSUM;
else
command |= MVNETA_TX_L3_IP6;
if (l4_proto == IPPROTO_TCP)
command |= MVNETA_TX_L4_CSUM_FULL;
else if (l4_proto == IPPROTO_UDP)
command |= MVNETA_TX_L4_UDP | MVNETA_TX_L4_CSUM_FULL;
else
command |= MVNETA_TX_L4_CSUM_NOT;
return command;
}
/* Display more error info */
static void mvneta_rx_error(struct mvneta_port *pp,
struct mvneta_rx_desc *rx_desc)
{
u32 status = rx_desc->status;
if (!mvneta_rxq_desc_is_first_last(rx_desc)) {
netdev_err(pp->dev,
"bad rx status %08x (buffer oversize), size=%d\n",
rx_desc->status, rx_desc->data_size);
return;
}
switch (status & MVNETA_RXD_ERR_CODE_MASK) {
case MVNETA_RXD_ERR_CRC:
netdev_err(pp->dev, "bad rx status %08x (crc error), size=%d\n",
status, rx_desc->data_size);
break;
case MVNETA_RXD_ERR_OVERRUN:
netdev_err(pp->dev, "bad rx status %08x (overrun error), size=%d\n",
status, rx_desc->data_size);
break;
case MVNETA_RXD_ERR_LEN:
netdev_err(pp->dev, "bad rx status %08x (max frame length error), size=%d\n",
status, rx_desc->data_size);
break;
case MVNETA_RXD_ERR_RESOURCE:
netdev_err(pp->dev, "bad rx status %08x (resource error), size=%d\n",
status, rx_desc->data_size);
break;
}
}
/* Handle RX checksum offload */
static void mvneta_rx_csum(struct mvneta_port *pp,
struct mvneta_rx_desc *rx_desc,
struct sk_buff *skb)
{
if ((rx_desc->status & MVNETA_RXD_L3_IP4) &&
(rx_desc->status & MVNETA_RXD_L4_CSUM_OK)) {
skb->csum = 0;
skb->ip_summed = CHECKSUM_UNNECESSARY;
return;
}
skb->ip_summed = CHECKSUM_NONE;
}
/* Return tx queue pointer (find last set bit) according to causeTxDone reg */
static struct mvneta_tx_queue *mvneta_tx_done_policy(struct mvneta_port *pp,
u32 cause)
{
int queue = fls(cause) - 1;
return (queue < 0 || queue >= txq_number) ? NULL : &pp->txqs[queue];
}
/* Free tx queue skbuffs */
static void mvneta_txq_bufs_free(struct mvneta_port *pp,
struct mvneta_tx_queue *txq, int num)
{
int i;
for (i = 0; i < num; i++) {
struct mvneta_tx_desc *tx_desc = txq->descs +
txq->txq_get_index;
struct sk_buff *skb = txq->tx_skb[txq->txq_get_index];
mvneta_txq_inc_get(txq);
if (!skb)
continue;
dma_unmap_single(pp->dev->dev.parent, tx_desc->buf_phys_addr,
tx_desc->data_size, DMA_TO_DEVICE);
dev_kfree_skb_any(skb);
}
}
/* Handle end of transmission */
static int mvneta_txq_done(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
struct netdev_queue *nq = netdev_get_tx_queue(pp->dev, txq->id);
int tx_done;
tx_done = mvneta_txq_sent_desc_proc(pp, txq);
if (tx_done == 0)
return tx_done;
mvneta_txq_bufs_free(pp, txq, tx_done);
txq->count -= tx_done;
if (netif_tx_queue_stopped(nq)) {
if (txq->size - txq->count >= MAX_SKB_FRAGS + 1)
netif_tx_wake_queue(nq);
}
return tx_done;
}
/* Refill processing */
static int mvneta_rx_refill(struct mvneta_port *pp,
struct mvneta_rx_desc *rx_desc)
{
dma_addr_t phys_addr;
struct sk_buff *skb;
skb = netdev_alloc_skb(pp->dev, pp->pkt_size);
if (!skb)
return -ENOMEM;
phys_addr = dma_map_single(pp->dev->dev.parent, skb->head,
MVNETA_RX_BUF_SIZE(pp->pkt_size),
DMA_FROM_DEVICE);
if (unlikely(dma_mapping_error(pp->dev->dev.parent, phys_addr))) {
dev_kfree_skb(skb);
return -ENOMEM;
}
mvneta_rx_desc_fill(rx_desc, phys_addr, (u32)skb);
return 0;
}
/* Handle tx checksum */
static u32 mvneta_skb_tx_csum(struct mvneta_port *pp, struct sk_buff *skb)
{
if (skb->ip_summed == CHECKSUM_PARTIAL) {
int ip_hdr_len = 0;
u8 l4_proto;
if (skb->protocol == htons(ETH_P_IP)) {
struct iphdr *ip4h = ip_hdr(skb);
/* Calculate IPv4 checksum and L4 checksum */
ip_hdr_len = ip4h->ihl;
l4_proto = ip4h->protocol;
} else if (skb->protocol == htons(ETH_P_IPV6)) {
struct ipv6hdr *ip6h = ipv6_hdr(skb);
/* Read l4_protocol from one of IPv6 extra headers */
if (skb_network_header_len(skb) > 0)
ip_hdr_len = (skb_network_header_len(skb) >> 2);
l4_proto = ip6h->nexthdr;
} else
return MVNETA_TX_L4_CSUM_NOT;
return mvneta_txq_desc_csum(skb_network_offset(skb),
skb->protocol, ip_hdr_len, l4_proto);
}
return MVNETA_TX_L4_CSUM_NOT;
}
/* Returns rx queue pointer (find last set bit) according to causeRxTx
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* value
*/
static struct mvneta_rx_queue *mvneta_rx_policy(struct mvneta_port *pp,
u32 cause)
{
int queue = fls(cause >> 8) - 1;
return (queue < 0 || queue >= rxq_number) ? NULL : &pp->rxqs[queue];
}
/* Drop packets received by the RXQ and free buffers */
static void mvneta_rxq_drop_pkts(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
int rx_done, i;
rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq);
for (i = 0; i < rxq->size; i++) {
struct mvneta_rx_desc *rx_desc = rxq->descs + i;
struct sk_buff *skb = (struct sk_buff *)rx_desc->buf_cookie;
dev_kfree_skb_any(skb);
dma_unmap_single(pp->dev->dev.parent, rx_desc->buf_phys_addr,
rx_desc->data_size, DMA_FROM_DEVICE);
}
if (rx_done)
mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_done);
}
/* Main rx processing */
static int mvneta_rx(struct mvneta_port *pp, int rx_todo,
struct mvneta_rx_queue *rxq)
{
struct net_device *dev = pp->dev;
int rx_done, rx_filled;
/* Get number of received packets */
rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq);
if (rx_todo > rx_done)
rx_todo = rx_done;
rx_done = 0;
rx_filled = 0;
/* Fairness NAPI loop */
while (rx_done < rx_todo) {
struct mvneta_rx_desc *rx_desc = mvneta_rxq_next_desc_get(rxq);
struct sk_buff *skb;
u32 rx_status;
int rx_bytes, err;
prefetch(rx_desc);
rx_done++;
rx_filled++;
rx_status = rx_desc->status;
skb = (struct sk_buff *)rx_desc->buf_cookie;
if (!mvneta_rxq_desc_is_first_last(rx_desc) ||
(rx_status & MVNETA_RXD_ERR_SUMMARY)) {
dev->stats.rx_errors++;
mvneta_rx_error(pp, rx_desc);
mvneta_rx_desc_fill(rx_desc, rx_desc->buf_phys_addr,
(u32)skb);
continue;
}
dma_unmap_single(pp->dev->dev.parent, rx_desc->buf_phys_addr,
rx_desc->data_size, DMA_FROM_DEVICE);
rx_bytes = rx_desc->data_size -
(ETH_FCS_LEN + MVNETA_MH_SIZE);
u64_stats_update_begin(&pp->rx_stats.syncp);
pp->rx_stats.packets++;
pp->rx_stats.bytes += rx_bytes;
u64_stats_update_end(&pp->rx_stats.syncp);
/* Linux processing */
skb_reserve(skb, MVNETA_MH_SIZE);
skb_put(skb, rx_bytes);
skb->protocol = eth_type_trans(skb, dev);
mvneta_rx_csum(pp, rx_desc, skb);
napi_gro_receive(&pp->napi, skb);
/* Refill processing */
err = mvneta_rx_refill(pp, rx_desc);
if (err) {
netdev_err(pp->dev, "Linux processing - Can't refill\n");
rxq->missed++;
rx_filled--;
}
}
/* Update rxq management counters */
mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_filled);
return rx_done;
}
/* Handle tx fragmentation processing */
static int mvneta_tx_frag_process(struct mvneta_port *pp, struct sk_buff *skb,
struct mvneta_tx_queue *txq)
{
struct mvneta_tx_desc *tx_desc;
int i;
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
void *addr = page_address(frag->page.p) + frag->page_offset;
tx_desc = mvneta_txq_next_desc_get(txq);
tx_desc->data_size = frag->size;
tx_desc->buf_phys_addr =
dma_map_single(pp->dev->dev.parent, addr,
tx_desc->data_size, DMA_TO_DEVICE);
if (dma_mapping_error(pp->dev->dev.parent,
tx_desc->buf_phys_addr)) {
mvneta_txq_desc_put(txq);
goto error;
}
if (i == (skb_shinfo(skb)->nr_frags - 1)) {
/* Last descriptor */
tx_desc->command = MVNETA_TXD_L_DESC | MVNETA_TXD_Z_PAD;
txq->tx_skb[txq->txq_put_index] = skb;
mvneta_txq_inc_put(txq);
} else {
/* Descriptor in the middle: Not First, Not Last */
tx_desc->command = 0;
txq->tx_skb[txq->txq_put_index] = NULL;
mvneta_txq_inc_put(txq);
}
}
return 0;
error:
/* Release all descriptors that were used to map fragments of
* this packet, as well as the corresponding DMA mappings
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
for (i = i - 1; i >= 0; i--) {
tx_desc = txq->descs + i;
dma_unmap_single(pp->dev->dev.parent,
tx_desc->buf_phys_addr,
tx_desc->data_size,
DMA_TO_DEVICE);
mvneta_txq_desc_put(txq);
}
return -ENOMEM;
}
/* Main tx processing */
static int mvneta_tx(struct sk_buff *skb, struct net_device *dev)
{
struct mvneta_port *pp = netdev_priv(dev);
struct mvneta_tx_queue *txq = &pp->txqs[txq_def];
struct mvneta_tx_desc *tx_desc;
struct netdev_queue *nq;
int frags = 0;
u32 tx_cmd;
if (!netif_running(dev))
goto out;
frags = skb_shinfo(skb)->nr_frags + 1;
nq = netdev_get_tx_queue(dev, txq_def);
/* Get a descriptor for the first part of the packet */
tx_desc = mvneta_txq_next_desc_get(txq);
tx_cmd = mvneta_skb_tx_csum(pp, skb);
tx_desc->data_size = skb_headlen(skb);
tx_desc->buf_phys_addr = dma_map_single(dev->dev.parent, skb->data,
tx_desc->data_size,
DMA_TO_DEVICE);
if (unlikely(dma_mapping_error(dev->dev.parent,
tx_desc->buf_phys_addr))) {
mvneta_txq_desc_put(txq);
frags = 0;
goto out;
}
if (frags == 1) {
/* First and Last descriptor */
tx_cmd |= MVNETA_TXD_FLZ_DESC;
tx_desc->command = tx_cmd;
txq->tx_skb[txq->txq_put_index] = skb;
mvneta_txq_inc_put(txq);
} else {
/* First but not Last */
tx_cmd |= MVNETA_TXD_F_DESC;
txq->tx_skb[txq->txq_put_index] = NULL;
mvneta_txq_inc_put(txq);
tx_desc->command = tx_cmd;
/* Continue with other skb fragments */
if (mvneta_tx_frag_process(pp, skb, txq)) {
dma_unmap_single(dev->dev.parent,
tx_desc->buf_phys_addr,
tx_desc->data_size,
DMA_TO_DEVICE);
mvneta_txq_desc_put(txq);
frags = 0;
goto out;
}
}
txq->count += frags;
mvneta_txq_pend_desc_add(pp, txq, frags);
if (txq->size - txq->count < MAX_SKB_FRAGS + 1)
netif_tx_stop_queue(nq);
out:
if (frags > 0) {
u64_stats_update_begin(&pp->tx_stats.syncp);
pp->tx_stats.packets++;
pp->tx_stats.bytes += skb->len;
u64_stats_update_end(&pp->tx_stats.syncp);
} else {
dev->stats.tx_dropped++;
dev_kfree_skb_any(skb);
}
if (txq->count >= MVNETA_TXDONE_COAL_PKTS)
mvneta_txq_done(pp, txq);
/* If after calling mvneta_txq_done, count equals
* frags, we need to set the timer
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
if (txq->count == frags && frags > 0)
mvneta_add_tx_done_timer(pp);
return NETDEV_TX_OK;
}
/* Free tx resources, when resetting a port */
static void mvneta_txq_done_force(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
int tx_done = txq->count;
mvneta_txq_bufs_free(pp, txq, tx_done);
/* reset txq */
txq->count = 0;
txq->txq_put_index = 0;
txq->txq_get_index = 0;
}
/* handle tx done - called from tx done timer callback */
static u32 mvneta_tx_done_gbe(struct mvneta_port *pp, u32 cause_tx_done,
int *tx_todo)
{
struct mvneta_tx_queue *txq;
u32 tx_done = 0;
struct netdev_queue *nq;
*tx_todo = 0;
while (cause_tx_done != 0) {
txq = mvneta_tx_done_policy(pp, cause_tx_done);
if (!txq)
break;
nq = netdev_get_tx_queue(pp->dev, txq->id);
__netif_tx_lock(nq, smp_processor_id());
if (txq->count) {
tx_done += mvneta_txq_done(pp, txq);
*tx_todo += txq->count;
}
__netif_tx_unlock(nq);
cause_tx_done &= ~((1 << txq->id));
}
return tx_done;
}
/* Compute crc8 of the specified address, using a unique algorithm ,
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* according to hw spec, different than generic crc8 algorithm
*/
static int mvneta_addr_crc(unsigned char *addr)
{
int crc = 0;
int i;
for (i = 0; i < ETH_ALEN; i++) {
int j;
crc = (crc ^ addr[i]) << 8;
for (j = 7; j >= 0; j--) {
if (crc & (0x100 << j))
crc ^= 0x107 << j;
}
}
return crc;
}
/* This method controls the net device special MAC multicast support.
* The Special Multicast Table for MAC addresses supports MAC of the form
* 0x01-00-5E-00-00-XX (where XX is between 0x00 and 0xFF).
* The MAC DA[7:0] bits are used as a pointer to the Special Multicast
* Table entries in the DA-Filter table. This method set the Special
* Multicast Table appropriate entry.
*/
static void mvneta_set_special_mcast_addr(struct mvneta_port *pp,
unsigned char last_byte,
int queue)
{
unsigned int smc_table_reg;
unsigned int tbl_offset;
unsigned int reg_offset;
/* Register offset from SMC table base */
tbl_offset = (last_byte / 4);
/* Entry offset within the above reg */
reg_offset = last_byte % 4;
smc_table_reg = mvreg_read(pp, (MVNETA_DA_FILT_SPEC_MCAST
+ tbl_offset * 4));
if (queue == -1)
smc_table_reg &= ~(0xff << (8 * reg_offset));
else {
smc_table_reg &= ~(0xff << (8 * reg_offset));
smc_table_reg |= ((0x01 | (queue << 1)) << (8 * reg_offset));
}
mvreg_write(pp, MVNETA_DA_FILT_SPEC_MCAST + tbl_offset * 4,
smc_table_reg);
}
/* This method controls the network device Other MAC multicast support.
* The Other Multicast Table is used for multicast of another type.
* A CRC-8 is used as an index to the Other Multicast Table entries
* in the DA-Filter table.
* The method gets the CRC-8 value from the calling routine and
* sets the Other Multicast Table appropriate entry according to the
* specified CRC-8 .
*/
static void mvneta_set_other_mcast_addr(struct mvneta_port *pp,
unsigned char crc8,
int queue)
{
unsigned int omc_table_reg;
unsigned int tbl_offset;
unsigned int reg_offset;
tbl_offset = (crc8 / 4) * 4; /* Register offset from OMC table base */
reg_offset = crc8 % 4; /* Entry offset within the above reg */
omc_table_reg = mvreg_read(pp, MVNETA_DA_FILT_OTH_MCAST + tbl_offset);
if (queue == -1) {
/* Clear accepts frame bit at specified Other DA table entry */
omc_table_reg &= ~(0xff << (8 * reg_offset));
} else {
omc_table_reg &= ~(0xff << (8 * reg_offset));
omc_table_reg |= ((0x01 | (queue << 1)) << (8 * reg_offset));
}
mvreg_write(pp, MVNETA_DA_FILT_OTH_MCAST + tbl_offset, omc_table_reg);
}
/* The network device supports multicast using two tables:
* 1) Special Multicast Table for MAC addresses of the form
* 0x01-00-5E-00-00-XX (where XX is between 0x00 and 0xFF).
* The MAC DA[7:0] bits are used as a pointer to the Special Multicast
* Table entries in the DA-Filter table.
* 2) Other Multicast Table for multicast of another type. A CRC-8 value
* is used as an index to the Other Multicast Table entries in the
* DA-Filter table.
*/
static int mvneta_mcast_addr_set(struct mvneta_port *pp, unsigned char *p_addr,
int queue)
{
unsigned char crc_result = 0;
if (memcmp(p_addr, "\x01\x00\x5e\x00\x00", 5) == 0) {
mvneta_set_special_mcast_addr(pp, p_addr[5], queue);
return 0;
}
crc_result = mvneta_addr_crc(p_addr);
if (queue == -1) {
if (pp->mcast_count[crc_result] == 0) {
netdev_info(pp->dev, "No valid Mcast for crc8=0x%02x\n",
crc_result);
return -EINVAL;
}
pp->mcast_count[crc_result]--;
if (pp->mcast_count[crc_result] != 0) {
netdev_info(pp->dev,
"After delete there are %d valid Mcast for crc8=0x%02x\n",
pp->mcast_count[crc_result], crc_result);
return -EINVAL;
}
} else
pp->mcast_count[crc_result]++;
mvneta_set_other_mcast_addr(pp, crc_result, queue);
return 0;
}
/* Configure Fitering mode of Ethernet port */
static void mvneta_rx_unicast_promisc_set(struct mvneta_port *pp,
int is_promisc)
{
u32 port_cfg_reg, val;
port_cfg_reg = mvreg_read(pp, MVNETA_PORT_CONFIG);
val = mvreg_read(pp, MVNETA_TYPE_PRIO);
/* Set / Clear UPM bit in port configuration register */
if (is_promisc) {
/* Accept all Unicast addresses */
port_cfg_reg |= MVNETA_UNI_PROMISC_MODE;
val |= MVNETA_FORCE_UNI;
mvreg_write(pp, MVNETA_MAC_ADDR_LOW, 0xffff);
mvreg_write(pp, MVNETA_MAC_ADDR_HIGH, 0xffffffff);
} else {
/* Reject all Unicast addresses */
port_cfg_reg &= ~MVNETA_UNI_PROMISC_MODE;
val &= ~MVNETA_FORCE_UNI;
}
mvreg_write(pp, MVNETA_PORT_CONFIG, port_cfg_reg);
mvreg_write(pp, MVNETA_TYPE_PRIO, val);
}
/* register unicast and multicast addresses */
static void mvneta_set_rx_mode(struct net_device *dev)
{
struct mvneta_port *pp = netdev_priv(dev);
struct netdev_hw_addr *ha;
if (dev->flags & IFF_PROMISC) {
/* Accept all: Multicast + Unicast */
mvneta_rx_unicast_promisc_set(pp, 1);
mvneta_set_ucast_table(pp, rxq_def);
mvneta_set_special_mcast_table(pp, rxq_def);
mvneta_set_other_mcast_table(pp, rxq_def);
} else {
/* Accept single Unicast */
mvneta_rx_unicast_promisc_set(pp, 0);
mvneta_set_ucast_table(pp, -1);
mvneta_mac_addr_set(pp, dev->dev_addr, rxq_def);
if (dev->flags & IFF_ALLMULTI) {
/* Accept all multicast */
mvneta_set_special_mcast_table(pp, rxq_def);
mvneta_set_other_mcast_table(pp, rxq_def);
} else {
/* Accept only initialized multicast */
mvneta_set_special_mcast_table(pp, -1);
mvneta_set_other_mcast_table(pp, -1);
if (!netdev_mc_empty(dev)) {
netdev_for_each_mc_addr(ha, dev) {
mvneta_mcast_addr_set(pp, ha->addr,
rxq_def);
}
}
}
}
}
/* Interrupt handling - the callback for request_irq() */
static irqreturn_t mvneta_isr(int irq, void *dev_id)
{
struct mvneta_port *pp = (struct mvneta_port *)dev_id;
/* Mask all interrupts */
mvreg_write(pp, MVNETA_INTR_NEW_MASK, 0);
napi_schedule(&pp->napi);
return IRQ_HANDLED;
}
/* NAPI handler
* Bits 0 - 7 of the causeRxTx register indicate that are transmitted
* packets on the corresponding TXQ (Bit 0 is for TX queue 1).
* Bits 8 -15 of the cause Rx Tx register indicate that are received
* packets on the corresponding RXQ (Bit 8 is for RX queue 0).
* Each CPU has its own causeRxTx register
*/
static int mvneta_poll(struct napi_struct *napi, int budget)
{
int rx_done = 0;
u32 cause_rx_tx;
unsigned long flags;
struct mvneta_port *pp = netdev_priv(napi->dev);
if (!netif_running(pp->dev)) {
napi_complete(napi);
return rx_done;
}
/* Read cause register */
cause_rx_tx = mvreg_read(pp, MVNETA_INTR_NEW_CAUSE) &
MVNETA_RX_INTR_MASK(rxq_number);
/* For the case where the last mvneta_poll did not process all
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* RX packets
*/
cause_rx_tx |= pp->cause_rx_tx;
if (rxq_number > 1) {
while ((cause_rx_tx != 0) && (budget > 0)) {
int count;
struct mvneta_rx_queue *rxq;
/* get rx queue number from cause_rx_tx */
rxq = mvneta_rx_policy(pp, cause_rx_tx);
if (!rxq)
break;
/* process the packet in that rx queue */
count = mvneta_rx(pp, budget, rxq);
rx_done += count;
budget -= count;
if (budget > 0) {
/* set off the rx bit of the
* corresponding bit in the cause rx
* tx register, so that next iteration
* will find the next rx queue where
* packets are received on
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
cause_rx_tx &= ~((1 << rxq->id) << 8);
}
}
} else {
rx_done = mvneta_rx(pp, budget, &pp->rxqs[rxq_def]);
budget -= rx_done;
}
if (budget > 0) {
cause_rx_tx = 0;
napi_complete(napi);
local_irq_save(flags);
mvreg_write(pp, MVNETA_INTR_NEW_MASK,
MVNETA_RX_INTR_MASK(rxq_number));
local_irq_restore(flags);
}
pp->cause_rx_tx = cause_rx_tx;
return rx_done;
}
/* tx done timer callback */
static void mvneta_tx_done_timer_callback(unsigned long data)
{
struct net_device *dev = (struct net_device *)data;
struct mvneta_port *pp = netdev_priv(dev);
int tx_done = 0, tx_todo = 0;
if (!netif_running(dev))
return ;
clear_bit(MVNETA_F_TX_DONE_TIMER_BIT, &pp->flags);
tx_done = mvneta_tx_done_gbe(pp,
(((1 << txq_number) - 1) &
MVNETA_CAUSE_TXQ_SENT_DESC_ALL_MASK),
&tx_todo);
if (tx_todo > 0)
mvneta_add_tx_done_timer(pp);
}
/* Handle rxq fill: allocates rxq skbs; called when initializing a port */
static int mvneta_rxq_fill(struct mvneta_port *pp, struct mvneta_rx_queue *rxq,
int num)
{
struct net_device *dev = pp->dev;
int i;
for (i = 0; i < num; i++) {
struct sk_buff *skb;
struct mvneta_rx_desc *rx_desc;
unsigned long phys_addr;
skb = dev_alloc_skb(pp->pkt_size);
if (!skb) {
netdev_err(dev, "%s:rxq %d, %d of %d buffs filled\n",
__func__, rxq->id, i, num);
break;
}
rx_desc = rxq->descs + i;
memset(rx_desc, 0, sizeof(struct mvneta_rx_desc));
phys_addr = dma_map_single(dev->dev.parent, skb->head,
MVNETA_RX_BUF_SIZE(pp->pkt_size),
DMA_FROM_DEVICE);
if (unlikely(dma_mapping_error(dev->dev.parent, phys_addr))) {
dev_kfree_skb(skb);
break;
}
mvneta_rx_desc_fill(rx_desc, phys_addr, (u32)skb);
}
/* Add this number of RX descriptors as non occupied (ready to
* get packets)
*/
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
mvneta_rxq_non_occup_desc_add(pp, rxq, i);
return i;
}
/* Free all packets pending transmit from all TXQs and reset TX port */
static void mvneta_tx_reset(struct mvneta_port *pp)
{
int queue;
/* free the skb's in the hal tx ring */
for (queue = 0; queue < txq_number; queue++)
mvneta_txq_done_force(pp, &pp->txqs[queue]);
mvreg_write(pp, MVNETA_PORT_TX_RESET, MVNETA_PORT_TX_DMA_RESET);
mvreg_write(pp, MVNETA_PORT_TX_RESET, 0);
}
static void mvneta_rx_reset(struct mvneta_port *pp)
{
mvreg_write(pp, MVNETA_PORT_RX_RESET, MVNETA_PORT_RX_DMA_RESET);
mvreg_write(pp, MVNETA_PORT_RX_RESET, 0);
}
/* Rx/Tx queue initialization/cleanup methods */
/* Create a specified RX queue */
static int mvneta_rxq_init(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
rxq->size = pp->rx_ring_size;
/* Allocate memory for RX descriptors */
rxq->descs = dma_alloc_coherent(pp->dev->dev.parent,
rxq->size * MVNETA_DESC_ALIGNED_SIZE,
&rxq->descs_phys, GFP_KERNEL);
if (rxq->descs == NULL) {
netdev_err(pp->dev,
"rxq=%d: Can't allocate %d bytes for %d RX descr\n",
rxq->id, rxq->size * MVNETA_DESC_ALIGNED_SIZE,
rxq->size);
return -ENOMEM;
}
BUG_ON(rxq->descs !=
PTR_ALIGN(rxq->descs, MVNETA_CPU_D_CACHE_LINE_SIZE));
rxq->last_desc = rxq->size - 1;
/* Set Rx descriptors queue starting address */
mvreg_write(pp, MVNETA_RXQ_BASE_ADDR_REG(rxq->id), rxq->descs_phys);
mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), rxq->size);
/* Set Offset */
mvneta_rxq_offset_set(pp, rxq, NET_SKB_PAD);
/* Set coalescing pkts and time */
mvneta_rx_pkts_coal_set(pp, rxq, rxq->pkts_coal);
mvneta_rx_time_coal_set(pp, rxq, rxq->time_coal);
/* Fill RXQ with buffers from RX pool */
mvneta_rxq_buf_size_set(pp, rxq, MVNETA_RX_BUF_SIZE(pp->pkt_size));
mvneta_rxq_bm_disable(pp, rxq);
mvneta_rxq_fill(pp, rxq, rxq->size);
return 0;
}
/* Cleanup Rx queue */
static void mvneta_rxq_deinit(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
mvneta_rxq_drop_pkts(pp, rxq);
if (rxq->descs)
dma_free_coherent(pp->dev->dev.parent,
rxq->size * MVNETA_DESC_ALIGNED_SIZE,
rxq->descs,
rxq->descs_phys);
rxq->descs = NULL;
rxq->last_desc = 0;
rxq->next_desc_to_proc = 0;
rxq->descs_phys = 0;
}
/* Create and initialize a tx queue */
static int mvneta_txq_init(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
txq->size = pp->tx_ring_size;
/* Allocate memory for TX descriptors */
txq->descs = dma_alloc_coherent(pp->dev->dev.parent,
txq->size * MVNETA_DESC_ALIGNED_SIZE,
&txq->descs_phys, GFP_KERNEL);
if (txq->descs == NULL) {
netdev_err(pp->dev,
"txQ=%d: Can't allocate %d bytes for %d TX descr\n",
txq->id, txq->size * MVNETA_DESC_ALIGNED_SIZE,
txq->size);
return -ENOMEM;
}
/* Make sure descriptor address is cache line size aligned */
BUG_ON(txq->descs !=
PTR_ALIGN(txq->descs, MVNETA_CPU_D_CACHE_LINE_SIZE));
txq->last_desc = txq->size - 1;
/* Set maximum bandwidth for enabled TXQs */
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0x03ffffff);
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0x3fffffff);
/* Set Tx descriptors queue starting address */
mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), txq->descs_phys);
mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), txq->size);
txq->tx_skb = kmalloc(txq->size * sizeof(*txq->tx_skb), GFP_KERNEL);
if (txq->tx_skb == NULL) {
dma_free_coherent(pp->dev->dev.parent,
txq->size * MVNETA_DESC_ALIGNED_SIZE,
txq->descs, txq->descs_phys);
return -ENOMEM;
}
mvneta_tx_done_pkts_coal_set(pp, txq, txq->done_pkts_coal);
return 0;
}
/* Free allocated resources when mvneta_txq_init() fails to allocate memory*/
static void mvneta_txq_deinit(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
kfree(txq->tx_skb);
if (txq->descs)
dma_free_coherent(pp->dev->dev.parent,
txq->size * MVNETA_DESC_ALIGNED_SIZE,
txq->descs, txq->descs_phys);
txq->descs = NULL;
txq->last_desc = 0;
txq->next_desc_to_proc = 0;
txq->descs_phys = 0;
/* Set minimum bandwidth for disabled TXQs */
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0);
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0);
/* Set Tx descriptors queue starting address and size */
mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), 0);
mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), 0);
}
/* Cleanup all Tx queues */
static void mvneta_cleanup_txqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < txq_number; queue++)
mvneta_txq_deinit(pp, &pp->txqs[queue]);
}
/* Cleanup all Rx queues */
static void mvneta_cleanup_rxqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < rxq_number; queue++)
mvneta_rxq_deinit(pp, &pp->rxqs[queue]);
}
/* Init all Rx queues */
static int mvneta_setup_rxqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < rxq_number; queue++) {
int err = mvneta_rxq_init(pp, &pp->rxqs[queue]);
if (err) {
netdev_err(pp->dev, "%s: can't create rxq=%d\n",
__func__, queue);
mvneta_cleanup_rxqs(pp);
return err;
}
}
return 0;
}
/* Init all tx queues */
static int mvneta_setup_txqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < txq_number; queue++) {
int err = mvneta_txq_init(pp, &pp->txqs[queue]);
if (err) {
netdev_err(pp->dev, "%s: can't create txq=%d\n",
__func__, queue);
mvneta_cleanup_txqs(pp);
return err;
}
}
return 0;
}
static void mvneta_start_dev(struct mvneta_port *pp)
{
mvneta_max_rx_size_set(pp, pp->pkt_size);
mvneta_txq_max_tx_size_set(pp, pp->pkt_size);
/* start the Rx/Tx activity */
mvneta_port_enable(pp);
/* Enable polling on the port */
napi_enable(&pp->napi);
/* Unmask interrupts */
mvreg_write(pp, MVNETA_INTR_NEW_MASK,
MVNETA_RX_INTR_MASK(rxq_number));
phy_start(pp->phy_dev);
netif_tx_start_all_queues(pp->dev);
}
static void mvneta_stop_dev(struct mvneta_port *pp)
{
phy_stop(pp->phy_dev);
napi_disable(&pp->napi);
netif_carrier_off(pp->dev);
mvneta_port_down(pp);
netif_tx_stop_all_queues(pp->dev);
/* Stop the port activity */
mvneta_port_disable(pp);
/* Clear all ethernet port interrupts */
mvreg_write(pp, MVNETA_INTR_MISC_CAUSE, 0);
mvreg_write(pp, MVNETA_INTR_OLD_CAUSE, 0);
/* Mask all ethernet port interrupts */
mvreg_write(pp, MVNETA_INTR_NEW_MASK, 0);
mvreg_write(pp, MVNETA_INTR_OLD_MASK, 0);
mvreg_write(pp, MVNETA_INTR_MISC_MASK, 0);
mvneta_tx_reset(pp);
mvneta_rx_reset(pp);
}
/* tx timeout callback - display a message and stop/start the network device */
static void mvneta_tx_timeout(struct net_device *dev)
{
struct mvneta_port *pp = netdev_priv(dev);
netdev_info(dev, "tx timeout\n");
mvneta_stop_dev(pp);
mvneta_start_dev(pp);
}
/* Return positive if MTU is valid */
static int mvneta_check_mtu_valid(struct net_device *dev, int mtu)
{
if (mtu < 68) {
netdev_err(dev, "cannot change mtu to less than 68\n");
return -EINVAL;
}
/* 9676 == 9700 - 20 and rounding to 8 */
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
if (mtu > 9676) {
netdev_info(dev, "Illegal MTU value %d, round to 9676\n", mtu);
mtu = 9676;
}
if (!IS_ALIGNED(MVNETA_RX_PKT_SIZE(mtu), 8)) {
netdev_info(dev, "Illegal MTU value %d, rounding to %d\n",
mtu, ALIGN(MVNETA_RX_PKT_SIZE(mtu), 8));
mtu = ALIGN(MVNETA_RX_PKT_SIZE(mtu), 8);
}
return mtu;
}
/* Change the device mtu */
static int mvneta_change_mtu(struct net_device *dev, int mtu)
{
struct mvneta_port *pp = netdev_priv(dev);
int ret;
mtu = mvneta_check_mtu_valid(dev, mtu);
if (mtu < 0)
return -EINVAL;
dev->mtu = mtu;
if (!netif_running(dev))
return 0;
/* The interface is running, so we have to force a
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* reallocation of the RXQs
*/
mvneta_stop_dev(pp);
mvneta_cleanup_txqs(pp);
mvneta_cleanup_rxqs(pp);
pp->pkt_size = MVNETA_RX_PKT_SIZE(pp->dev->mtu);
ret = mvneta_setup_rxqs(pp);
if (ret) {
netdev_err(pp->dev, "unable to setup rxqs after MTU change\n");
return ret;
}
mvneta_setup_txqs(pp);
mvneta_start_dev(pp);
mvneta_port_up(pp);
return 0;
}
/* Handle setting mac address */
static int mvneta_set_mac_addr(struct net_device *dev, void *addr)
{
struct mvneta_port *pp = netdev_priv(dev);
u8 *mac = addr + 2;
int i;
if (netif_running(dev))
return -EBUSY;
/* Remove previous address table entry */
mvneta_mac_addr_set(pp, dev->dev_addr, -1);
/* Set new addr in hw */
mvneta_mac_addr_set(pp, mac, rxq_def);
/* Set addr in the device */
for (i = 0; i < ETH_ALEN; i++)
dev->dev_addr[i] = mac[i];
return 0;
}
static void mvneta_adjust_link(struct net_device *ndev)
{
struct mvneta_port *pp = netdev_priv(ndev);
struct phy_device *phydev = pp->phy_dev;
int status_change = 0;
if (phydev->link) {
if ((pp->speed != phydev->speed) ||
(pp->duplex != phydev->duplex)) {
u32 val;
val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
val &= ~(MVNETA_GMAC_CONFIG_MII_SPEED |
MVNETA_GMAC_CONFIG_GMII_SPEED |
MVNETA_GMAC_CONFIG_FULL_DUPLEX);
if (phydev->duplex)
val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
if (phydev->speed == SPEED_1000)
val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
else
val |= MVNETA_GMAC_CONFIG_MII_SPEED;
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
pp->duplex = phydev->duplex;
pp->speed = phydev->speed;
}
}
if (phydev->link != pp->link) {
if (!phydev->link) {
pp->duplex = -1;
pp->speed = 0;
}
pp->link = phydev->link;
status_change = 1;
}
if (status_change) {
if (phydev->link) {
u32 val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
val |= (MVNETA_GMAC_FORCE_LINK_PASS |
MVNETA_GMAC_FORCE_LINK_DOWN);
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
mvneta_port_up(pp);
netdev_info(pp->dev, "link up\n");
} else {
mvneta_port_down(pp);
netdev_info(pp->dev, "link down\n");
}
}
}
static int mvneta_mdio_probe(struct mvneta_port *pp)
{
struct phy_device *phy_dev;
phy_dev = of_phy_connect(pp->dev, pp->phy_node, mvneta_adjust_link, 0,
pp->phy_interface);
if (!phy_dev) {
netdev_err(pp->dev, "could not find the PHY\n");
return -ENODEV;
}
phy_dev->supported &= PHY_GBIT_FEATURES;
phy_dev->advertising = phy_dev->supported;
pp->phy_dev = phy_dev;
pp->link = 0;
pp->duplex = 0;
pp->speed = 0;
return 0;
}
static void mvneta_mdio_remove(struct mvneta_port *pp)
{
phy_disconnect(pp->phy_dev);
pp->phy_dev = NULL;
}
static int mvneta_open(struct net_device *dev)
{
struct mvneta_port *pp = netdev_priv(dev);
int ret;
mvneta_mac_addr_set(pp, dev->dev_addr, rxq_def);
pp->pkt_size = MVNETA_RX_PKT_SIZE(pp->dev->mtu);
ret = mvneta_setup_rxqs(pp);
if (ret)
return ret;
ret = mvneta_setup_txqs(pp);
if (ret)
goto err_cleanup_rxqs;
/* Connect to port interrupt line */
ret = request_irq(pp->dev->irq, mvneta_isr, 0,
MVNETA_DRIVER_NAME, pp);
if (ret) {
netdev_err(pp->dev, "cannot request irq %d\n", pp->dev->irq);
goto err_cleanup_txqs;
}
/* In default link is down */
netif_carrier_off(pp->dev);
ret = mvneta_mdio_probe(pp);
if (ret < 0) {
netdev_err(dev, "cannot probe MDIO bus\n");
goto err_free_irq;
}
mvneta_start_dev(pp);
return 0;
err_free_irq:
free_irq(pp->dev->irq, pp);
err_cleanup_txqs:
mvneta_cleanup_txqs(pp);
err_cleanup_rxqs:
mvneta_cleanup_rxqs(pp);
return ret;
}
/* Stop the port, free port interrupt line */
static int mvneta_stop(struct net_device *dev)
{
struct mvneta_port *pp = netdev_priv(dev);
mvneta_stop_dev(pp);
mvneta_mdio_remove(pp);
free_irq(dev->irq, pp);
mvneta_cleanup_rxqs(pp);
mvneta_cleanup_txqs(pp);
del_timer(&pp->tx_done_timer);
clear_bit(MVNETA_F_TX_DONE_TIMER_BIT, &pp->flags);
return 0;
}
/* Ethtool methods */
/* Get settings (phy address, speed) for ethtools */
int mvneta_ethtool_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct mvneta_port *pp = netdev_priv(dev);
if (!pp->phy_dev)
return -ENODEV;
return phy_ethtool_gset(pp->phy_dev, cmd);
}
/* Set settings (phy address, speed) for ethtools */
int mvneta_ethtool_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct mvneta_port *pp = netdev_priv(dev);
if (!pp->phy_dev)
return -ENODEV;
return phy_ethtool_sset(pp->phy_dev, cmd);
}
/* Set interrupt coalescing for ethtools */
static int mvneta_ethtool_set_coalesce(struct net_device *dev,
struct ethtool_coalesce *c)
{
struct mvneta_port *pp = netdev_priv(dev);
int queue;
for (queue = 0; queue < rxq_number; queue++) {
struct mvneta_rx_queue *rxq = &pp->rxqs[queue];
rxq->time_coal = c->rx_coalesce_usecs;
rxq->pkts_coal = c->rx_max_coalesced_frames;
mvneta_rx_pkts_coal_set(pp, rxq, rxq->pkts_coal);
mvneta_rx_time_coal_set(pp, rxq, rxq->time_coal);
}
for (queue = 0; queue < txq_number; queue++) {
struct mvneta_tx_queue *txq = &pp->txqs[queue];
txq->done_pkts_coal = c->tx_max_coalesced_frames;
mvneta_tx_done_pkts_coal_set(pp, txq, txq->done_pkts_coal);
}
return 0;
}
/* get coalescing for ethtools */
static int mvneta_ethtool_get_coalesce(struct net_device *dev,
struct ethtool_coalesce *c)
{
struct mvneta_port *pp = netdev_priv(dev);
c->rx_coalesce_usecs = pp->rxqs[0].time_coal;
c->rx_max_coalesced_frames = pp->rxqs[0].pkts_coal;
c->tx_max_coalesced_frames = pp->txqs[0].done_pkts_coal;
return 0;
}
static void mvneta_ethtool_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *drvinfo)
{
strlcpy(drvinfo->driver, MVNETA_DRIVER_NAME,
sizeof(drvinfo->driver));
strlcpy(drvinfo->version, MVNETA_DRIVER_VERSION,
sizeof(drvinfo->version));
strlcpy(drvinfo->bus_info, dev_name(&dev->dev),
sizeof(drvinfo->bus_info));
}
static void mvneta_ethtool_get_ringparam(struct net_device *netdev,
struct ethtool_ringparam *ring)
{
struct mvneta_port *pp = netdev_priv(netdev);
ring->rx_max_pending = MVNETA_MAX_RXD;
ring->tx_max_pending = MVNETA_MAX_TXD;
ring->rx_pending = pp->rx_ring_size;
ring->tx_pending = pp->tx_ring_size;
}
static int mvneta_ethtool_set_ringparam(struct net_device *dev,
struct ethtool_ringparam *ring)
{
struct mvneta_port *pp = netdev_priv(dev);
if ((ring->rx_pending == 0) || (ring->tx_pending == 0))
return -EINVAL;
pp->rx_ring_size = ring->rx_pending < MVNETA_MAX_RXD ?
ring->rx_pending : MVNETA_MAX_RXD;
pp->tx_ring_size = ring->tx_pending < MVNETA_MAX_TXD ?
ring->tx_pending : MVNETA_MAX_TXD;
if (netif_running(dev)) {
mvneta_stop(dev);
if (mvneta_open(dev)) {
netdev_err(dev,
"error on opening device after ring param change\n");
return -ENOMEM;
}
}
return 0;
}
static const struct net_device_ops mvneta_netdev_ops = {
.ndo_open = mvneta_open,
.ndo_stop = mvneta_stop,
.ndo_start_xmit = mvneta_tx,
.ndo_set_rx_mode = mvneta_set_rx_mode,
.ndo_set_mac_address = mvneta_set_mac_addr,
.ndo_change_mtu = mvneta_change_mtu,
.ndo_tx_timeout = mvneta_tx_timeout,
.ndo_get_stats64 = mvneta_get_stats64,
};
const struct ethtool_ops mvneta_eth_tool_ops = {
.get_link = ethtool_op_get_link,
.get_settings = mvneta_ethtool_get_settings,
.set_settings = mvneta_ethtool_set_settings,
.set_coalesce = mvneta_ethtool_set_coalesce,
.get_coalesce = mvneta_ethtool_get_coalesce,
.get_drvinfo = mvneta_ethtool_get_drvinfo,
.get_ringparam = mvneta_ethtool_get_ringparam,
.set_ringparam = mvneta_ethtool_set_ringparam,
};
/* Initialize hw */
static int __devinit mvneta_init(struct mvneta_port *pp, int phy_addr)
{
int queue;
/* Disable port */
mvneta_port_disable(pp);
/* Set port default values */
mvneta_defaults_set(pp);
pp->txqs = kzalloc(txq_number * sizeof(struct mvneta_tx_queue),
GFP_KERNEL);
if (!pp->txqs)
return -ENOMEM;
/* Initialize TX descriptor rings */
for (queue = 0; queue < txq_number; queue++) {
struct mvneta_tx_queue *txq = &pp->txqs[queue];
txq->id = queue;
txq->size = pp->tx_ring_size;
txq->done_pkts_coal = MVNETA_TXDONE_COAL_PKTS;
}
pp->rxqs = kzalloc(rxq_number * sizeof(struct mvneta_rx_queue),
GFP_KERNEL);
if (!pp->rxqs) {
kfree(pp->txqs);
return -ENOMEM;
}
/* Create Rx descriptor rings */
for (queue = 0; queue < rxq_number; queue++) {
struct mvneta_rx_queue *rxq = &pp->rxqs[queue];
rxq->id = queue;
rxq->size = pp->rx_ring_size;
rxq->pkts_coal = MVNETA_RX_COAL_PKTS;
rxq->time_coal = MVNETA_RX_COAL_USEC;
}
return 0;
}
static void mvneta_deinit(struct mvneta_port *pp)
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
{
kfree(pp->txqs);
kfree(pp->rxqs);
}
/* platform glue : initialize decoding windows */
static void __devinit
mvneta_conf_mbus_windows(struct mvneta_port *pp,
const struct mbus_dram_target_info *dram)
{
u32 win_enable;
u32 win_protect;
int i;
for (i = 0; i < 6; i++) {
mvreg_write(pp, MVNETA_WIN_BASE(i), 0);
mvreg_write(pp, MVNETA_WIN_SIZE(i), 0);
if (i < 4)
mvreg_write(pp, MVNETA_WIN_REMAP(i), 0);
}
win_enable = 0x3f;
win_protect = 0;
for (i = 0; i < dram->num_cs; i++) {
const struct mbus_dram_window *cs = dram->cs + i;
mvreg_write(pp, MVNETA_WIN_BASE(i), (cs->base & 0xffff0000) |
(cs->mbus_attr << 8) | dram->mbus_dram_target_id);
mvreg_write(pp, MVNETA_WIN_SIZE(i),
(cs->size - 1) & 0xffff0000);
win_enable &= ~(1 << i);
win_protect |= 3 << (2 * i);
}
mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable);
}
/* Power up the port */
static void __devinit mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
{
u32 val;
/* MAC Cause register should be cleared */
mvreg_write(pp, MVNETA_UNIT_INTR_CAUSE, 0);
if (phy_mode == PHY_INTERFACE_MODE_SGMII)
mvneta_port_sgmii_config(pp);
mvneta_gmac_rgmii_set(pp, 1);
/* Cancel Port Reset */
val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
val &= ~MVNETA_GMAC2_PORT_RESET;
mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
while ((mvreg_read(pp, MVNETA_GMAC_CTRL_2) &
MVNETA_GMAC2_PORT_RESET) != 0)
continue;
}
/* Device initialization routine */
static int __devinit mvneta_probe(struct platform_device *pdev)
{
const struct mbus_dram_target_info *dram_target_info;
struct device_node *dn = pdev->dev.of_node;
struct device_node *phy_node;
u32 phy_addr;
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
struct mvneta_port *pp;
struct net_device *dev;
const char *mac_addr;
int phy_mode;
int err;
/* Our multiqueue support is not complete, so for now, only
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
* allow the usage of the first RX queue
*/
if (rxq_def != 0) {
dev_err(&pdev->dev, "Invalid rxq_def argument: %d\n", rxq_def);
return -EINVAL;
}
dev = alloc_etherdev_mq(sizeof(struct mvneta_port), 8);
if (!dev)
return -ENOMEM;
dev->irq = irq_of_parse_and_map(dn, 0);
if (dev->irq == 0) {
err = -EINVAL;
goto err_free_netdev;
}
phy_node = of_parse_phandle(dn, "phy", 0);
if (!phy_node) {
dev_err(&pdev->dev, "no associated PHY\n");
err = -ENODEV;
goto err_free_irq;
}
phy_mode = of_get_phy_mode(dn);
if (phy_mode < 0) {
dev_err(&pdev->dev, "incorrect phy-mode\n");
err = -EINVAL;
goto err_free_irq;
}
mac_addr = of_get_mac_address(dn);
if (!mac_addr || !is_valid_ether_addr(mac_addr))
eth_hw_addr_random(dev);
else
memcpy(dev->dev_addr, mac_addr, ETH_ALEN);
dev->tx_queue_len = MVNETA_MAX_TXD;
dev->watchdog_timeo = 5 * HZ;
dev->netdev_ops = &mvneta_netdev_ops;
SET_ETHTOOL_OPS(dev, &mvneta_eth_tool_ops);
pp = netdev_priv(dev);
pp->tx_done_timer.function = mvneta_tx_done_timer_callback;
init_timer(&pp->tx_done_timer);
clear_bit(MVNETA_F_TX_DONE_TIMER_BIT, &pp->flags);
pp->weight = MVNETA_RX_POLL_WEIGHT;
pp->phy_node = phy_node;
pp->phy_interface = phy_mode;
pp->base = of_iomap(dn, 0);
if (pp->base == NULL) {
err = -ENOMEM;
goto err_free_irq;
}
pp->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(pp->clk)) {
err = PTR_ERR(pp->clk);
goto err_unmap;
}
clk_prepare_enable(pp->clk);
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
pp->tx_done_timer.data = (unsigned long)dev;
pp->tx_ring_size = MVNETA_MAX_TXD;
pp->rx_ring_size = MVNETA_MAX_RXD;
pp->dev = dev;
SET_NETDEV_DEV(dev, &pdev->dev);
err = mvneta_init(pp, phy_addr);
if (err < 0) {
dev_err(&pdev->dev, "can't init eth hal\n");
goto err_clk;
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
}
mvneta_port_power_up(pp, phy_mode);
dram_target_info = mv_mbus_dram_info();
if (dram_target_info)
mvneta_conf_mbus_windows(pp, dram_target_info);
netif_napi_add(dev, &pp->napi, mvneta_poll, pp->weight);
err = register_netdev(dev);
if (err < 0) {
dev_err(&pdev->dev, "failed to register\n");
goto err_deinit;
}
dev->features = NETIF_F_SG | NETIF_F_IP_CSUM;
dev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM;
dev->priv_flags |= IFF_UNICAST_FLT;
netdev_info(dev, "mac: %pM\n", dev->dev_addr);
platform_set_drvdata(pdev, pp->dev);
return 0;
err_deinit:
mvneta_deinit(pp);
err_clk:
clk_disable_unprepare(pp->clk);
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
err_unmap:
iounmap(pp->base);
err_free_irq:
irq_dispose_mapping(dev->irq);
err_free_netdev:
free_netdev(dev);
return err;
}
/* Device removal routine */
static int __devexit mvneta_remove(struct platform_device *pdev)
{
struct net_device *dev = platform_get_drvdata(pdev);
struct mvneta_port *pp = netdev_priv(dev);
unregister_netdev(dev);
mvneta_deinit(pp);
clk_disable_unprepare(pp->clk);
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 19:04:28 +08:00
iounmap(pp->base);
irq_dispose_mapping(dev->irq);
free_netdev(dev);
platform_set_drvdata(pdev, NULL);
return 0;
}
static const struct of_device_id mvneta_match[] = {
{ .compatible = "marvell,armada-370-neta" },
{ }
};
MODULE_DEVICE_TABLE(of, mvneta_match);
static struct platform_driver mvneta_driver = {
.probe = mvneta_probe,
.remove = __devexit_p(mvneta_remove),
.driver = {
.name = MVNETA_DRIVER_NAME,
.of_match_table = mvneta_match,
},
};
module_platform_driver(mvneta_driver);
MODULE_DESCRIPTION("Marvell NETA Ethernet Driver - www.marvell.com");
MODULE_AUTHOR("Rami Rosen <rosenr@marvell.com>, Thomas Petazzoni <thomas.petazzoni@free-electrons.com>");
MODULE_LICENSE("GPL");
module_param(rxq_number, int, S_IRUGO);
module_param(txq_number, int, S_IRUGO);
module_param(rxq_def, int, S_IRUGO);
module_param(txq_def, int, S_IRUGO);