OpenCloudOS-Kernel/drivers/i2c/chips/max6875.c

/*
    max6875.c - driver for MAX6874/MAX6875

    Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>

    Based on i2c/chips/eeprom.c

    The MAX6875 has a bank of registers and two banks of EEPROM.
    Address ranges are defined as follows:
     * 0x0000 - 0x0046 = configuration registers
     * 0x8000 - 0x8046 = configuration EEPROM
     * 0x8100 - 0x82FF = user EEPROM

    This driver makes the user EEPROM available for read.

    The registers & config EEPROM should be accessed via i2c-dev.

    The MAX6875 ignores the lowest address bit, so each chip responds to
    two addresses - 0x50/0x51 and 0x52/0x53.

    Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read
    address, so this driver is destructive if loaded for the wrong EEPROM chip.

    This program is free software; you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation; version 2 of the License.
*/

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/mutex.h>

/* Do not scan - the MAX6875 access method will write to some EEPROM chips */
static const unsigned short normal_i2c[] = { I2C_CLIENT_END };

/* Insmod parameters */
I2C_CLIENT_INSMOD_1(max6875);

/* The MAX6875 can only read/write 16 bytes at a time */
#define SLICE_SIZE			16
#define SLICE_BITS			4

/* USER EEPROM is at addresses 0x8100 - 0x82FF */
#define USER_EEPROM_BASE		0x8100
#define USER_EEPROM_SIZE		0x0200
#define USER_EEPROM_SLICES		32

/* MAX6875 commands */
#define MAX6875_CMD_BLK_READ		0x84

/* Each client has this additional data */
struct max6875_data {
	struct i2c_client	*fake_client;
	struct mutex		update_lock;

	u32			valid;
	u8			data[USER_EEPROM_SIZE];
	unsigned long		last_updated[USER_EEPROM_SLICES];
};

static void max6875_update_slice(struct i2c_client *client, int slice)
{
	struct max6875_data *data = i2c_get_clientdata(client);
	int i, j, addr;
	u8 *buf;

	if (slice >= USER_EEPROM_SLICES)
		return;

	mutex_lock(&data->update_lock);

	buf = &data->data[slice << SLICE_BITS];

	if (!(data->valid & (1 << slice)) ||
	    time_after(jiffies, data->last_updated[slice])) {

		dev_dbg(&client->dev, "Starting update of slice %u\n", slice);

		data->valid &= ~(1 << slice);

		addr = USER_EEPROM_BASE + (slice << SLICE_BITS);

		/* select the eeprom address */
		if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
			dev_err(&client->dev, "address set failed\n");
			goto exit_up;
		}

		if (i2c_check_functionality(client->adapter,
					    I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
			if (i2c_smbus_read_i2c_block_data(client,
							  MAX6875_CMD_BLK_READ,
							  SLICE_SIZE,
							  buf) != SLICE_SIZE) {
				goto exit_up;
			}
		} else {
			for (i = 0; i < SLICE_SIZE; i++) {
				j = i2c_smbus_read_byte(client);
				if (j < 0) {
					goto exit_up;
				}
				buf[i] = j;
			}
		}
		data->last_updated[slice] = jiffies;
		data->valid |= (1 << slice);
	}
exit_up:
	mutex_unlock(&data->update_lock);
}

static ssize_t max6875_read(struct kobject *kobj,
			    struct bin_attribute *bin_attr,
			    char *buf, loff_t off, size_t count)
{
	struct i2c_client *client = kobj_to_i2c_client(kobj);
	struct max6875_data *data = i2c_get_clientdata(client);
	int slice, max_slice;

	if (off > USER_EEPROM_SIZE)
		return 0;

	if (off + count > USER_EEPROM_SIZE)
		count = USER_EEPROM_SIZE - off;

	/* refresh slices which contain requested bytes */
	max_slice = (off + count - 1) >> SLICE_BITS;
	for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++)
		max6875_update_slice(client, slice);

	memcpy(buf, &data->data[off], count);

	return count;
}

static struct bin_attribute user_eeprom_attr = {
	.attr = {
		.name = "eeprom",
		.mode = S_IRUGO,
	},
	.size = USER_EEPROM_SIZE,
	.read = max6875_read,
};

/* Return 0 if detection is successful, -ENODEV otherwise */
static int max6875_detect(struct i2c_client *client, int kind,
			  struct i2c_board_info *info)
{
	struct i2c_adapter *adapter = client->adapter;

	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
				     | I2C_FUNC_SMBUS_READ_BYTE))
		return -ENODEV;

	/* Only check even addresses */
	if (client->addr & 1)
		return -ENODEV;

	strlcpy(info->type, "max6875", I2C_NAME_SIZE);

	return 0;
}

static int max6875_probe(struct i2c_client *client,
			 const struct i2c_device_id *id)
{
	struct max6875_data *data;
	int err;

	if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL)))
		return -ENOMEM;

	/* A fake client is created on the odd address */
	data->fake_client = i2c_new_dummy(client->adapter, client->addr + 1);
	if (!data->fake_client) {
		err = -ENOMEM;
		goto exit_kfree;
	}

	/* Init real i2c_client */
	i2c_set_clientdata(client, data);
	mutex_init(&data->update_lock);

	err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr);
	if (err)
		goto exit_remove_fake;

	return 0;

exit_remove_fake:
	i2c_unregister_device(data->fake_client);
exit_kfree:
	kfree(data);
	return err;
}

static int max6875_remove(struct i2c_client *client)
{
	struct max6875_data *data = i2c_get_clientdata(client);

	i2c_unregister_device(data->fake_client);

	sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr);
	kfree(data);

	return 0;
}

static const struct i2c_device_id max6875_id[] = {
	{ "max6875", 0 },
	{ }
};

static struct i2c_driver max6875_driver = {
	.driver = {
		.name	= "max6875",
	},
	.probe		= max6875_probe,
	.remove		= max6875_remove,
	.id_table	= max6875_id,

	.detect		= max6875_detect,
	.address_data	= &addr_data,
};

static int __init max6875_init(void)
{
	return i2c_add_driver(&max6875_driver);
}

static void __exit max6875_exit(void)
{
	i2c_del_driver(&max6875_driver);
}


MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
MODULE_DESCRIPTION("MAX6875 driver");
MODULE_LICENSE("GPL");

module_init(max6875_init);
module_exit(max6875_exit);