UbiquitousOS
/
OpenCloudOS-Kernel
mirror of https://gitee.com/OpenCloudOS/OpenCloudOS-Kernel.git
11
0
Fork 0
Code Issues Projects Releases Wiki Activity
OpenCloudOS-Kernel/include/linux/pinctrl/pinctrl-state.h

33 lines
1.5 KiB
C
Raw Normal View History

pinctrl: split pincontrol states into its own header Move the pin control state defines into its own header file, since it is used both by machine.h which is facing the platform and by consumer.h which is facing the drivers, and pinctrl.h which is pinctrl-driver internal, let's not have each and every .h file include all others, then isolation is moot. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-07 04:15:51 +08:00
/*
* Standard pin control state definitions
*/
pinctrl: add sleep state definition There is an IDLE definition in the pinctrl framework, but for ux500 SLEEP is more apropriate. I've added some comments on the semantics of the common states so as to avoid misunderstandings. ChangeLog v1->v2: - Fixed terminology "on"->"into". Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-07 17:17:53 +08:00
/**
* @PINCTRL_STATE_DEFAULT: the state the pinctrl handle shall be put
* into as default, usually this means the pins are up and ready to
* be used by the device driver. This state is commonly used by
pinctrl: clarify idle vs sleep states This pure documentation fix tries to align the "idle" and "sleep" pin states to the idle and suspend states from runtime PM. Cc: Patrice Chotard <patrice.chotard@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-26 20:59:47 +08:00
* hogs to configure muxing and pins at boot, and also as a state
* to go into when returning from sleep and idle in
* .pm_runtime_resume() or ordinary .resume() for example.
drivers/pinctrl: Add the concept of an "init" state For pinctrl the "default" state is applied to pins before the driver's probe function is called. This is normally a sensible thing to do, but in some cases can cause problems. That's because the pins will change state before the driver is given a chance to program how those pins should behave. As an example you might have a regulator that is controlled by a PWM (output high = high voltage, output low = low voltage). The firmware might leave this pin as driven high. If we allow the driver core to reconfigure this pin as a PWM pin before the PWM's probe function runs then you might end up running at too low of a voltage while we probe. Let's introudce a new "init" state. If this is defined we'll set pinctrl to this state before probe and then "default" after probe (unless the driver explicitly changed states already). An alternative idea that was thought of was to use the pre-existing "sleep" or "idle" states and add a boolean property that we should start in that mode. This was not done because the "init" state is needed for correctness and those other states are only present (and only transitioned in to and out of) when (optional) power management is enabled. Changes in v3: - Moved declarations to pinctrl/devinfo.h - Fixed author/SoB Changes in v2: - Added comment to pinctrl_init_done() as per Linus W. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 12:15:06 +08:00
* @PINCTRL_STATE_INIT: normally the pinctrl will be set to "default"
* before the driver's probe() function is called. There are some
* drivers where that is not appropriate becausing doing so would
* glitch the pins. In those cases you can add an "init" pinctrl
* which is the state of the pins before drive probe. After probe
* if the pins are still in "init" state they'll be moved to
* "default".
pinctrl: add sleep state definition There is an IDLE definition in the pinctrl framework, but for ux500 SLEEP is more apropriate. I've added some comments on the semantics of the common states so as to avoid misunderstandings. ChangeLog v1->v2: - Fixed terminology "on"->"into". Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-07 17:17:53 +08:00
* @PINCTRL_STATE_IDLE: the state the pinctrl handle shall be put into
pinctrl: clarify idle vs sleep states This pure documentation fix tries to align the "idle" and "sleep" pin states to the idle and suspend states from runtime PM. Cc: Patrice Chotard <patrice.chotard@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-26 20:59:47 +08:00
* when the pins are idle. This is a state where the system is relaxed
* but not fully sleeping - some power may be on but clocks gated for
* example. Could typically be set from a pm_runtime_suspend() or
* pm_runtime_idle() operation.
pinctrl: add sleep state definition There is an IDLE definition in the pinctrl framework, but for ux500 SLEEP is more apropriate. I've added some comments on the semantics of the common states so as to avoid misunderstandings. ChangeLog v1->v2: - Fixed terminology "on"->"into". Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-07 17:17:53 +08:00
* @PINCTRL_STATE_SLEEP: the state the pinctrl handle shall be put into
pinctrl: clarify idle vs sleep states This pure documentation fix tries to align the "idle" and "sleep" pin states to the idle and suspend states from runtime PM. Cc: Patrice Chotard <patrice.chotard@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-26 20:59:47 +08:00
* when the pins are sleeping. This is a state where the system is in
* its lowest sleep state. Could typically be set from an
* ordinary .suspend() function.
pinctrl: add sleep state definition There is an IDLE definition in the pinctrl framework, but for ux500 SLEEP is more apropriate. I've added some comments on the semantics of the common states so as to avoid misunderstandings. ChangeLog v1->v2: - Fixed terminology "on"->"into". Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-07 17:17:53 +08:00
*/
pinctrl: split pincontrol states into its own header Move the pin control state defines into its own header file, since it is used both by machine.h which is facing the platform and by consumer.h which is facing the drivers, and pinctrl.h which is pinctrl-driver internal, let's not have each and every .h file include all others, then isolation is moot. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-07 04:15:51 +08:00
#define PINCTRL_STATE_DEFAULT "default"
drivers/pinctrl: Add the concept of an "init" state For pinctrl the "default" state is applied to pins before the driver's probe function is called. This is normally a sensible thing to do, but in some cases can cause problems. That's because the pins will change state before the driver is given a chance to program how those pins should behave. As an example you might have a regulator that is controlled by a PWM (output high = high voltage, output low = low voltage). The firmware might leave this pin as driven high. If we allow the driver core to reconfigure this pin as a PWM pin before the PWM's probe function runs then you might end up running at too low of a voltage while we probe. Let's introudce a new "init" state. If this is defined we'll set pinctrl to this state before probe and then "default" after probe (unless the driver explicitly changed states already). An alternative idea that was thought of was to use the pre-existing "sleep" or "idle" states and add a boolean property that we should start in that mode. This was not done because the "init" state is needed for correctness and those other states are only present (and only transitioned in to and out of) when (optional) power management is enabled. Changes in v3: - Moved declarations to pinctrl/devinfo.h - Fixed author/SoB Changes in v2: - Added comment to pinctrl_init_done() as per Linus W. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 12:15:06 +08:00
#define PINCTRL_STATE_INIT "init"
pinctrl: split pincontrol states into its own header Move the pin control state defines into its own header file, since it is used both by machine.h which is facing the platform and by consumer.h which is facing the drivers, and pinctrl.h which is pinctrl-driver internal, let's not have each and every .h file include all others, then isolation is moot. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-07 04:15:51 +08:00
#define PINCTRL_STATE_IDLE "idle"
pinctrl: add sleep state definition There is an IDLE definition in the pinctrl framework, but for ux500 SLEEP is more apropriate. I've added some comments on the semantics of the common states so as to avoid misunderstandings. ChangeLog v1->v2: - Fixed terminology "on"->"into". Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-07 17:17:53 +08:00
#define PINCTRL_STATE_SLEEP "sleep"