OpenCloudOS-Kernel/drivers/scsi/sd_zbc.c

730 lines
18 KiB
C
Raw Normal View History

sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
/*
* SCSI Zoned Block commands
*
* Copyright (C) 2014-2015 SUSE Linux GmbH
* Written by: Hannes Reinecke <hare@suse.de>
* Modified by: Damien Le Moal <damien.lemoal@hgst.com>
* Modified by: Shaun Tancheff <shaun.tancheff@seagate.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License version
* 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139,
* USA.
*
*/
#include <linux/blkdev.h>
#include <asm/unaligned.h>
#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include "sd.h"
/**
* sd_zbc_parse_report - Convert a zone descriptor to a struct blk_zone,
* @sdkp: The disk the report originated from
* @buf: Address of the report zone descriptor
* @zone: the destination zone structure
*
* All LBA sized values are converted to 512B sectors unit.
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
*/
static void sd_zbc_parse_report(struct scsi_disk *sdkp, u8 *buf,
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
struct blk_zone *zone)
{
struct scsi_device *sdp = sdkp->device;
memset(zone, 0, sizeof(struct blk_zone));
zone->type = buf[0] & 0x0f;
zone->cond = (buf[1] >> 4) & 0xf;
if (buf[1] & 0x01)
zone->reset = 1;
if (buf[1] & 0x02)
zone->non_seq = 1;
zone->len = logical_to_sectors(sdp, get_unaligned_be64(&buf[8]));
zone->start = logical_to_sectors(sdp, get_unaligned_be64(&buf[16]));
zone->wp = logical_to_sectors(sdp, get_unaligned_be64(&buf[24]));
if (zone->type != ZBC_ZONE_TYPE_CONV &&
zone->cond == ZBC_ZONE_COND_FULL)
zone->wp = zone->start + zone->len;
}
/**
* sd_zbc_report_zones - Issue a REPORT ZONES scsi command.
* @sdkp: The target disk
* @buf: Buffer to use for the reply
* @buflen: the buffer size
* @lba: Start LBA of the report
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
* @partial: Do partial report
*
* For internal use during device validation.
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
* Using partial=true can significantly speed up execution of a report zones
* command because the disk does not have to count all possible report matching
* zones and will only report the count of zones fitting in the command reply
* buffer.
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
*/
static int sd_zbc_report_zones(struct scsi_disk *sdkp, unsigned char *buf,
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
unsigned int buflen, sector_t lba,
bool partial)
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
{
struct scsi_device *sdp = sdkp->device;
const int timeout = sdp->request_queue->rq_timeout;
struct scsi_sense_hdr sshdr;
unsigned char cmd[16];
unsigned int rep_len;
int result;
memset(cmd, 0, 16);
cmd[0] = ZBC_IN;
cmd[1] = ZI_REPORT_ZONES;
put_unaligned_be64(lba, &cmd[2]);
put_unaligned_be32(buflen, &cmd[10]);
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
if (partial)
cmd[14] = ZBC_REPORT_ZONE_PARTIAL;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
memset(buf, 0, buflen);
result = scsi_execute_req(sdp, cmd, DMA_FROM_DEVICE,
buf, buflen, &sshdr,
timeout, SD_MAX_RETRIES, NULL);
if (result) {
sd_printk(KERN_ERR, sdkp,
"REPORT ZONES lba %llu failed with %d/%d\n",
(unsigned long long)lba,
host_byte(result), driver_byte(result));
return -EIO;
}
rep_len = get_unaligned_be32(&buf[0]);
if (rep_len < 64) {
sd_printk(KERN_ERR, sdkp,
"REPORT ZONES report invalid length %u\n",
rep_len);
return -EIO;
}
return 0;
}
/**
* sd_zbc_setup_report_cmnd - Prepare a REPORT ZONES scsi command
* @cmd: The command to setup
*
* Call in sd_init_command() for a REQ_OP_ZONE_REPORT request.
*/
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
int sd_zbc_setup_report_cmnd(struct scsi_cmnd *cmd)
{
struct request *rq = cmd->request;
struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
sector_t lba, sector = blk_rq_pos(rq);
unsigned int nr_bytes = blk_rq_bytes(rq);
int ret;
WARN_ON(nr_bytes == 0);
if (!sd_is_zoned(sdkp))
/* Not a zoned device */
return BLKPREP_KILL;
ret = scsi_init_io(cmd);
if (ret != BLKPREP_OK)
return ret;
cmd->cmd_len = 16;
memset(cmd->cmnd, 0, cmd->cmd_len);
cmd->cmnd[0] = ZBC_IN;
cmd->cmnd[1] = ZI_REPORT_ZONES;
lba = sectors_to_logical(sdkp->device, sector);
put_unaligned_be64(lba, &cmd->cmnd[2]);
put_unaligned_be32(nr_bytes, &cmd->cmnd[10]);
/* Do partial report for speeding things up */
cmd->cmnd[14] = ZBC_REPORT_ZONE_PARTIAL;
cmd->sc_data_direction = DMA_FROM_DEVICE;
cmd->sdb.length = nr_bytes;
cmd->transfersize = sdkp->device->sector_size;
cmd->allowed = 0;
return BLKPREP_OK;
}
/**
* sd_zbc_report_zones_complete - Process a REPORT ZONES scsi command reply.
* @scmd: The completed report zones command
* @good_bytes: reply size in bytes
*
* Convert all reported zone descriptors to struct blk_zone. The conversion
* is done in-place, directly in the request specified sg buffer.
*/
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
static void sd_zbc_report_zones_complete(struct scsi_cmnd *scmd,
unsigned int good_bytes)
{
struct request *rq = scmd->request;
struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
struct sg_mapping_iter miter;
struct blk_zone_report_hdr hdr;
struct blk_zone zone;
unsigned int offset, bytes = 0;
unsigned long flags;
u8 *buf;
if (good_bytes < 64)
return;
memset(&hdr, 0, sizeof(struct blk_zone_report_hdr));
sg_miter_start(&miter, scsi_sglist(scmd), scsi_sg_count(scmd),
SG_MITER_TO_SG | SG_MITER_ATOMIC);
local_irq_save(flags);
while (sg_miter_next(&miter) && bytes < good_bytes) {
buf = miter.addr;
offset = 0;
if (bytes == 0) {
/* Set the report header */
hdr.nr_zones = min_t(unsigned int,
(good_bytes - 64) / 64,
get_unaligned_be32(&buf[0]) / 64);
memcpy(buf, &hdr, sizeof(struct blk_zone_report_hdr));
offset += 64;
bytes += 64;
}
/* Parse zone descriptors */
while (offset < miter.length && hdr.nr_zones) {
WARN_ON(offset > miter.length);
buf = miter.addr + offset;
sd_zbc_parse_report(sdkp, buf, &zone);
memcpy(buf, &zone, sizeof(struct blk_zone));
offset += 64;
bytes += 64;
hdr.nr_zones--;
}
if (!hdr.nr_zones)
break;
}
sg_miter_stop(&miter);
local_irq_restore(flags);
}
/**
* sd_zbc_zone_sectors - Get the device zone size in number of 512B sectors.
* @sdkp: The target disk
*/
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
static inline sector_t sd_zbc_zone_sectors(struct scsi_disk *sdkp)
{
return logical_to_sectors(sdkp->device, sdkp->zone_blocks);
}
/**
* sd_zbc_setup_reset_cmnd - Prepare a RESET WRITE POINTER scsi command.
* @cmd: the command to setup
*
* Called from sd_init_command() for a REQ_OP_ZONE_RESET request.
*/
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
int sd_zbc_setup_reset_cmnd(struct scsi_cmnd *cmd)
{
struct request *rq = cmd->request;
struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
sector_t sector = blk_rq_pos(rq);
sector_t block = sectors_to_logical(sdkp->device, sector);
if (!sd_is_zoned(sdkp))
/* Not a zoned device */
return BLKPREP_KILL;
if (sdkp->device->changed)
return BLKPREP_KILL;
if (sector & (sd_zbc_zone_sectors(sdkp) - 1))
/* Unaligned request */
return BLKPREP_KILL;
cmd->cmd_len = 16;
memset(cmd->cmnd, 0, cmd->cmd_len);
cmd->cmnd[0] = ZBC_OUT;
cmd->cmnd[1] = ZO_RESET_WRITE_POINTER;
put_unaligned_be64(block, &cmd->cmnd[2]);
rq->timeout = SD_TIMEOUT;
cmd->sc_data_direction = DMA_NONE;
cmd->transfersize = 0;
cmd->allowed = 0;
return BLKPREP_OK;
}
/**
* sd_zbc_complete - ZBC command post processing.
* @cmd: Completed command
* @good_bytes: Command reply bytes
* @sshdr: command sense header
*
* Called from sd_done(). Process report zones reply and handle reset zone
* and write commands errors.
*/
void sd_zbc_complete(struct scsi_cmnd *cmd, unsigned int good_bytes,
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
struct scsi_sense_hdr *sshdr)
{
int result = cmd->result;
struct request *rq = cmd->request;
switch (req_op(rq)) {
case REQ_OP_ZONE_RESET:
if (result &&
sshdr->sense_key == ILLEGAL_REQUEST &&
sshdr->asc == 0x24)
/*
* INVALID FIELD IN CDB error: reset of a conventional
* zone was attempted. Nothing to worry about, so be
* quiet about the error.
*/
rq->rq_flags |= RQF_QUIET;
break;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
case REQ_OP_WRITE:
case REQ_OP_WRITE_ZEROES:
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
case REQ_OP_WRITE_SAME:
break;
case REQ_OP_ZONE_REPORT:
if (!result)
sd_zbc_report_zones_complete(cmd, good_bytes);
break;
}
}
/**
* sd_zbc_check_zoned_characteristics - Check zoned block device characteristics
* @sdkp: Target disk
* @buf: Buffer where to store the VPD page data
*
* Read VPD page B6, get information and check that reads are unconstrained.
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
*/
static int sd_zbc_check_zoned_characteristics(struct scsi_disk *sdkp,
unsigned char *buf)
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
{
if (scsi_get_vpd_page(sdkp->device, 0xb6, buf, 64)) {
sd_printk(KERN_NOTICE, sdkp,
"Read zoned characteristics VPD page failed\n");
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
return -ENODEV;
}
if (sdkp->device->type != TYPE_ZBC) {
/* Host-aware */
sdkp->urswrz = 1;
sdkp->zones_optimal_open = get_unaligned_be32(&buf[8]);
sdkp->zones_optimal_nonseq = get_unaligned_be32(&buf[12]);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
sdkp->zones_max_open = 0;
} else {
/* Host-managed */
sdkp->urswrz = buf[4] & 1;
sdkp->zones_optimal_open = 0;
sdkp->zones_optimal_nonseq = 0;
sdkp->zones_max_open = get_unaligned_be32(&buf[16]);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
}
/*
* Check for unconstrained reads: host-managed devices with
* constrained reads (drives failing read after write pointer)
* are not supported.
*/
if (!sdkp->urswrz) {
if (sdkp->first_scan)
sd_printk(KERN_NOTICE, sdkp,
"constrained reads devices are not supported\n");
return -ENODEV;
}
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
return 0;
}
#define SD_ZBC_BUF_SIZE 131072U
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
/**
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
* sd_zbc_check_zones - Check the device capacity and zone sizes
* @sdkp: Target disk
*
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
* Check that the device capacity as reported by READ CAPACITY matches the
* max_lba value (plus one)of the report zones command reply. Also check that
* all zones of the device have an equal size, only allowing the last zone of
* the disk to have a smaller size (runt zone). The zone size must also be a
* power of two.
*
* Returns the zone size in number of blocks upon success or an error code
* upon failure.
*/
static int sd_zbc_check_zones(struct scsi_disk *sdkp, u32 *zblocks)
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
{
u64 zone_blocks = 0;
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
sector_t max_lba, block = 0;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
unsigned char *buf;
unsigned char *rec;
unsigned int buf_len;
unsigned int list_length;
int ret;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
u8 same;
/* Get a buffer */
buf = kmalloc(SD_ZBC_BUF_SIZE, GFP_KERNEL);
if (!buf)
return -ENOMEM;
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
/* Do a report zone to get max_lba and the same field */
ret = sd_zbc_report_zones(sdkp, buf, SD_ZBC_BUF_SIZE, 0, false);
if (ret)
goto out_free;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
if (sdkp->rc_basis == 0) {
/* The max_lba field is the capacity of this device */
max_lba = get_unaligned_be64(&buf[8]);
if (sdkp->capacity != max_lba + 1) {
if (sdkp->first_scan)
sd_printk(KERN_WARNING, sdkp,
"Changing capacity from %llu to max LBA+1 %llu\n",
(unsigned long long)sdkp->capacity,
(unsigned long long)max_lba + 1);
sdkp->capacity = max_lba + 1;
}
}
/*
* Check same field: for any value other than 0, we know that all zones
* have the same size.
*/
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
same = buf[4] & 0x0f;
if (same > 0) {
rec = &buf[64];
zone_blocks = get_unaligned_be64(&rec[8]);
goto out;
}
/*
* Check the size of all zones: all zones must be of
* equal size, except the last zone which can be smaller
* than other zones.
*/
do {
/* Parse REPORT ZONES header */
list_length = get_unaligned_be32(&buf[0]) + 64;
rec = buf + 64;
buf_len = min(list_length, SD_ZBC_BUF_SIZE);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
/* Parse zone descriptors */
while (rec < buf + buf_len) {
u64 this_zone_blocks = get_unaligned_be64(&rec[8]);
if (zone_blocks == 0) {
zone_blocks = this_zone_blocks;
} else if (this_zone_blocks != zone_blocks &&
(block + this_zone_blocks < sdkp->capacity
|| this_zone_blocks > zone_blocks)) {
zone_blocks = 0;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
goto out;
}
block += this_zone_blocks;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
rec += 64;
}
if (block < sdkp->capacity) {
ret = sd_zbc_report_zones(sdkp, buf,
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
SD_ZBC_BUF_SIZE, block, true);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
if (ret)
goto out_free;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
}
} while (block < sdkp->capacity);
out:
if (!zone_blocks) {
if (sdkp->first_scan)
sd_printk(KERN_NOTICE, sdkp,
"Devices with non constant zone "
"size are not supported\n");
ret = -ENODEV;
} else if (!is_power_of_2(zone_blocks)) {
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
if (sdkp->first_scan)
sd_printk(KERN_NOTICE, sdkp,
"Devices with non power of 2 zone "
"size are not supported\n");
ret = -ENODEV;
} else if (logical_to_sectors(sdkp->device, zone_blocks) > UINT_MAX) {
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
if (sdkp->first_scan)
sd_printk(KERN_NOTICE, sdkp,
"Zone size too large\n");
ret = -EFBIG;
} else {
*zblocks = zone_blocks;
ret = 0;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
}
out_free:
kfree(buf);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
return ret;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
}
/**
* sd_zbc_alloc_zone_bitmap - Allocate a zone bitmap (one bit per zone).
* @nr_zones: Number of zones to allocate space for.
* @numa_node: NUMA node to allocate the memory from.
*/
static inline unsigned long *
sd_zbc_alloc_zone_bitmap(u32 nr_zones, int numa_node)
{
treewide: kzalloc_node() -> kcalloc_node() The kzalloc_node() function has a 2-factor argument form, kcalloc_node(). This patch replaces cases of: kzalloc_node(a * b, gfp, node) with: kcalloc_node(a * b, gfp, node) as well as handling cases of: kzalloc_node(a * b * c, gfp, node) with: kzalloc_node(array3_size(a, b, c), gfp, node) as it's slightly less ugly than: kcalloc_node(array_size(a, b), c, gfp, node) This does, however, attempt to ignore constant size factors like: kzalloc_node(4 * 1024, gfp, node) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc_node( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc_node( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc_node( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(char) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc_node + kcalloc_node ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc_node( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc_node( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc_node( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc_node( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc_node(C1 * C2 * C3, ...) | kzalloc_node( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc_node( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc_node( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc_node( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc_node(sizeof(THING) * C2, ...) | kzalloc_node(sizeof(TYPE) * C2, ...) | kzalloc_node(C1 * C2 * C3, ...) | kzalloc_node(C1 * C2, ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - (E1) * E2 + E1, E2 , ...) | - kzalloc_node + kcalloc_node ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc_node + kcalloc_node ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-13 05:04:20 +08:00
return kcalloc_node(BITS_TO_LONGS(nr_zones), sizeof(unsigned long),
GFP_KERNEL, numa_node);
}
/**
* sd_zbc_get_seq_zones - Parse report zones reply to identify sequential zones
* @sdkp: disk used
* @buf: report reply buffer
* @buflen: length of @buf
* @zone_shift: logarithm base 2 of the number of blocks in a zone
* @seq_zones_bitmap: bitmap of sequential zones to set
*
* Parse reported zone descriptors in @buf to identify sequential zones and
* set the reported zone bit in @seq_zones_bitmap accordingly.
* Since read-only and offline zones cannot be written, do not
* mark them as sequential in the bitmap.
* Return the LBA after the last zone reported.
*/
static sector_t sd_zbc_get_seq_zones(struct scsi_disk *sdkp, unsigned char *buf,
unsigned int buflen, u32 zone_shift,
unsigned long *seq_zones_bitmap)
{
sector_t lba, next_lba = sdkp->capacity;
unsigned int buf_len, list_length;
unsigned char *rec;
u8 type, cond;
list_length = get_unaligned_be32(&buf[0]) + 64;
buf_len = min(list_length, buflen);
rec = buf + 64;
while (rec < buf + buf_len) {
type = rec[0] & 0x0f;
cond = (rec[1] >> 4) & 0xf;
lba = get_unaligned_be64(&rec[16]);
if (type != ZBC_ZONE_TYPE_CONV &&
cond != ZBC_ZONE_COND_READONLY &&
cond != ZBC_ZONE_COND_OFFLINE)
set_bit(lba >> zone_shift, seq_zones_bitmap);
next_lba = lba + get_unaligned_be64(&rec[8]);
rec += 64;
}
return next_lba;
}
/**
* sd_zbc_setup_seq_zones_bitmap - Initialize a seq zone bitmap.
* @sdkp: target disk
* @zone_shift: logarithm base 2 of the number of blocks in a zone
* @nr_zones: number of zones to set up a seq zone bitmap for
*
* Allocate a zone bitmap and initialize it by identifying sequential zones.
*/
static unsigned long *
sd_zbc_setup_seq_zones_bitmap(struct scsi_disk *sdkp, u32 zone_shift,
u32 nr_zones)
{
struct request_queue *q = sdkp->disk->queue;
unsigned long *seq_zones_bitmap;
sector_t lba = 0;
unsigned char *buf;
int ret = -ENOMEM;
seq_zones_bitmap = sd_zbc_alloc_zone_bitmap(nr_zones, q->node);
if (!seq_zones_bitmap)
return ERR_PTR(-ENOMEM);
buf = kmalloc(SD_ZBC_BUF_SIZE, GFP_KERNEL);
if (!buf)
goto out;
while (lba < sdkp->capacity) {
scsi: sd_zbc: Reduce boot device scan and revalidate time Handling checks of ZBC device capacity using the max_lba field of the REPORT ZONES command reply for disks with rc_basis == 0 can be done using the same report zones command reply used to check the "same" field. Avoid executing a report zones command solely to check the disk capacity by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and renaming that function to sd_zbc_check_zones(). This removes a costly execution of a full report zones command and so reduces device scan duration at boot time as well as the duration of disk revalidate calls. Furthermore, setting the partial report bit in the REPORT ZONES command cdb can significantly reduce this command execution time as the device does not have to count and report the total number of zones that could be reported assuming a large enough reply buffer. A non-partial zone report is necessary only for the first execution of report zones used to check the same field value (to ensure that this value applies to all zones of the disk). All other calls to sd_zbc_report_zones() can use a partial report to reduce execution time. Using a 14 TB ZBC disk, these simple changes reduce device scan time at boot from about 3.5s down to about 900ms. Disk revalidate times are also reduced from about 450ms down to 230ms. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-10-12 18:08:41 +08:00
ret = sd_zbc_report_zones(sdkp, buf, SD_ZBC_BUF_SIZE,
lba, true);
if (ret)
goto out;
lba = sd_zbc_get_seq_zones(sdkp, buf, SD_ZBC_BUF_SIZE,
zone_shift, seq_zones_bitmap);
}
if (lba != sdkp->capacity) {
/* Something went wrong */
ret = -EIO;
}
out:
kfree(buf);
if (ret) {
kfree(seq_zones_bitmap);
return ERR_PTR(ret);
}
return seq_zones_bitmap;
}
static void sd_zbc_cleanup(struct scsi_disk *sdkp)
{
struct request_queue *q = sdkp->disk->queue;
kfree(q->seq_zones_bitmap);
q->seq_zones_bitmap = NULL;
kfree(q->seq_zones_wlock);
q->seq_zones_wlock = NULL;
q->nr_zones = 0;
}
static int sd_zbc_setup(struct scsi_disk *sdkp, u32 zone_blocks)
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
{
struct request_queue *q = sdkp->disk->queue;
u32 zone_shift = ilog2(zone_blocks);
u32 nr_zones;
int ret;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
/* chunk_sectors indicates the zone size */
blk_queue_chunk_sectors(q,
logical_to_sectors(sdkp->device, zone_blocks));
nr_zones = round_up(sdkp->capacity, zone_blocks) >> zone_shift;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
/*
* Initialize the device request queue information if the number
* of zones changed.
*/
if (nr_zones != sdkp->nr_zones || nr_zones != q->nr_zones) {
unsigned long *seq_zones_wlock = NULL, *seq_zones_bitmap = NULL;
size_t zone_bitmap_size;
if (nr_zones) {
seq_zones_wlock = sd_zbc_alloc_zone_bitmap(nr_zones,
q->node);
if (!seq_zones_wlock) {
ret = -ENOMEM;
goto err;
}
seq_zones_bitmap = sd_zbc_setup_seq_zones_bitmap(sdkp,
zone_shift, nr_zones);
if (IS_ERR(seq_zones_bitmap)) {
ret = PTR_ERR(seq_zones_bitmap);
kfree(seq_zones_wlock);
goto err;
}
}
zone_bitmap_size = BITS_TO_LONGS(nr_zones) *
sizeof(unsigned long);
blk_mq_freeze_queue(q);
if (q->nr_zones != nr_zones) {
/* READ16/WRITE16 is mandatory for ZBC disks */
sdkp->device->use_16_for_rw = 1;
sdkp->device->use_10_for_rw = 0;
sdkp->zone_blocks = zone_blocks;
sdkp->zone_shift = zone_shift;
sdkp->nr_zones = nr_zones;
q->nr_zones = nr_zones;
swap(q->seq_zones_wlock, seq_zones_wlock);
swap(q->seq_zones_bitmap, seq_zones_bitmap);
} else if (memcmp(q->seq_zones_bitmap, seq_zones_bitmap,
zone_bitmap_size) != 0) {
memcpy(q->seq_zones_bitmap, seq_zones_bitmap,
zone_bitmap_size);
}
blk_mq_unfreeze_queue(q);
kfree(seq_zones_wlock);
kfree(seq_zones_bitmap);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
}
return 0;
err:
sd_zbc_cleanup(sdkp);
return ret;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
}
int sd_zbc_read_zones(struct scsi_disk *sdkp, unsigned char *buf)
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
{
u32 zone_blocks;
int ret;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
if (!sd_is_zoned(sdkp))
/*
* Device managed or normal SCSI disk,
* no special handling required
*/
return 0;
/* Check zoned block device characteristics (unconstrained reads) */
ret = sd_zbc_check_zoned_characteristics(sdkp, buf);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
if (ret)
goto err;
/*
* Check zone size: only devices with a constant zone size (except
* an eventual last runt zone) that is a power of 2 are supported.
*/
ret = sd_zbc_check_zones(sdkp, &zone_blocks);
if (ret != 0)
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
goto err;
/* The drive satisfies the kernel restrictions: set it up */
ret = sd_zbc_setup(sdkp, zone_blocks);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
if (ret)
goto err;
return 0;
err:
sdkp->capacity = 0;
sd_zbc_cleanup(sdkp);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
return ret;
}
void sd_zbc_remove(struct scsi_disk *sdkp)
{
sd_zbc_cleanup(sdkp);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 14:40:34 +08:00
}
void sd_zbc_print_zones(struct scsi_disk *sdkp)
{
if (!sd_is_zoned(sdkp) || !sdkp->capacity)
return;
if (sdkp->capacity & (sdkp->zone_blocks - 1))
sd_printk(KERN_NOTICE, sdkp,
"%u zones of %u logical blocks + 1 runt zone\n",
sdkp->nr_zones - 1,
sdkp->zone_blocks);
else
sd_printk(KERN_NOTICE, sdkp,
"%u zones of %u logical blocks\n",
sdkp->nr_zones,
sdkp->zone_blocks);
}