OpenCloudOS-Kernel/include/soc/tegra/mc.h

248 lines
5.4 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0-only */
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
/*
* Copyright (C) 2014 NVIDIA Corporation
*/
#ifndef __SOC_TEGRA_MC_H__
#define __SOC_TEGRA_MC_H__
#include <linux/bits.h>
#include <linux/debugfs.h>
#include <linux/err.h>
#include <linux/interconnect-provider.h>
#include <linux/irq.h>
#include <linux/reset-controller.h>
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
#include <linux/types.h>
struct clk;
struct device;
struct page;
struct tegra_mc_timing {
unsigned long rate;
u32 *emem_data;
};
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
struct tegra_mc_client {
unsigned int id;
const char *name;
/*
* For Tegra210 and earlier, this is the SWGROUP ID used for IOVA translations in the
* Tegra SMMU, whereas on Tegra186 and later this is the ID used to override the ARM SMMU
* stream ID used for IOVA translations for the given memory client.
*/
union {
unsigned int swgroup;
unsigned int sid;
};
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
unsigned int fifo_size;
struct {
/* Tegra SMMU enable (Tegra210 and earlier) */
struct {
unsigned int reg;
unsigned int bit;
} smmu;
/* latency allowance */
struct {
unsigned int reg;
unsigned int shift;
unsigned int mask;
unsigned int def;
} la;
/* stream ID overrides (Tegra186 and later) */
struct {
unsigned int override;
unsigned int security;
} sid;
} regs;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
};
struct tegra_smmu_swgroup {
const char *name;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
unsigned int swgroup;
unsigned int reg;
};
struct tegra_smmu_group_soc {
const char *name;
const unsigned int *swgroups;
unsigned int num_swgroups;
};
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
struct tegra_smmu_soc {
const struct tegra_mc_client *clients;
unsigned int num_clients;
const struct tegra_smmu_swgroup *swgroups;
unsigned int num_swgroups;
const struct tegra_smmu_group_soc *groups;
unsigned int num_groups;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
bool supports_round_robin_arbitration;
bool supports_request_limit;
unsigned int num_tlb_lines;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
unsigned int num_asids;
};
struct tegra_mc;
struct tegra_smmu;
struct gart_device;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
#ifdef CONFIG_TEGRA_IOMMU_SMMU
struct tegra_smmu *tegra_smmu_probe(struct device *dev,
const struct tegra_smmu_soc *soc,
struct tegra_mc *mc);
void tegra_smmu_remove(struct tegra_smmu *smmu);
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
#else
static inline struct tegra_smmu *
tegra_smmu_probe(struct device *dev, const struct tegra_smmu_soc *soc,
struct tegra_mc *mc)
{
return NULL;
}
static inline void tegra_smmu_remove(struct tegra_smmu *smmu)
{
}
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
#endif
#ifdef CONFIG_TEGRA_IOMMU_GART
struct gart_device *tegra_gart_probe(struct device *dev, struct tegra_mc *mc);
int tegra_gart_suspend(struct gart_device *gart);
int tegra_gart_resume(struct gart_device *gart);
#else
static inline struct gart_device *
tegra_gart_probe(struct device *dev, struct tegra_mc *mc)
{
return ERR_PTR(-ENODEV);
}
static inline int tegra_gart_suspend(struct gart_device *gart)
{
return -ENODEV;
}
static inline int tegra_gart_resume(struct gart_device *gart)
{
return -ENODEV;
}
#endif
struct tegra_mc_reset {
const char *name;
unsigned long id;
unsigned int control;
unsigned int status;
unsigned int reset;
unsigned int bit;
};
struct tegra_mc_reset_ops {
int (*hotreset_assert)(struct tegra_mc *mc,
const struct tegra_mc_reset *rst);
int (*hotreset_deassert)(struct tegra_mc *mc,
const struct tegra_mc_reset *rst);
int (*block_dma)(struct tegra_mc *mc,
const struct tegra_mc_reset *rst);
bool (*dma_idling)(struct tegra_mc *mc,
const struct tegra_mc_reset *rst);
int (*unblock_dma)(struct tegra_mc *mc,
const struct tegra_mc_reset *rst);
int (*reset_status)(struct tegra_mc *mc,
const struct tegra_mc_reset *rst);
};
#define TEGRA_MC_ICC_TAG_DEFAULT 0
#define TEGRA_MC_ICC_TAG_ISO BIT(0)
struct tegra_mc_icc_ops {
int (*set)(struct icc_node *src, struct icc_node *dst);
int (*aggregate)(struct icc_node *node, u32 tag, u32 avg_bw,
u32 peak_bw, u32 *agg_avg, u32 *agg_peak);
struct icc_node_data *(*xlate_extended)(struct of_phandle_args *spec,
void *data);
};
struct tegra_mc_ops {
/*
* @probe: Callback to set up SoC-specific bits of the memory controller. This is called
* after basic, common set up that is done by the SoC-agnostic bits.
*/
int (*probe)(struct tegra_mc *mc);
void (*remove)(struct tegra_mc *mc);
int (*suspend)(struct tegra_mc *mc);
int (*resume)(struct tegra_mc *mc);
irqreturn_t (*handle_irq)(int irq, void *data);
};
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
struct tegra_mc_soc {
const struct tegra_mc_client *clients;
unsigned int num_clients;
const unsigned long *emem_regs;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
unsigned int num_emem_regs;
unsigned int num_address_bits;
unsigned int atom_size;
u8 client_id_mask;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
const struct tegra_smmu_soc *smmu;
u32 intmask;
const struct tegra_mc_reset_ops *reset_ops;
const struct tegra_mc_reset *resets;
unsigned int num_resets;
const struct tegra_mc_icc_ops *icc_ops;
const struct tegra_mc_ops *ops;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
};
struct tegra_mc {
struct device *dev;
struct tegra_smmu *smmu;
struct gart_device *gart;
void __iomem *regs;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
struct clk *clk;
int irq;
const struct tegra_mc_soc *soc;
unsigned long tick;
struct tegra_mc_timing *timings;
unsigned int num_timings;
struct reset_controller_dev reset;
struct icc_provider provider;
spinlock_t lock;
struct {
struct dentry *root;
} debugfs;
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
};
int tegra_mc_write_emem_configuration(struct tegra_mc *mc, unsigned long rate);
unsigned int tegra_mc_get_emem_device_count(struct tegra_mc *mc);
#ifdef CONFIG_TEGRA_MC
struct tegra_mc *devm_tegra_memory_controller_get(struct device *dev);
#else
static inline struct tegra_mc *
devm_tegra_memory_controller_get(struct device *dev)
{
return ERR_PTR(-ENODEV);
}
#endif
memory: Add NVIDIA Tegra memory controller support The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-04-16 15:24:44 +08:00
#endif /* __SOC_TEGRA_MC_H__ */