OpenCloudOS-Kernel/drivers/media/tuners/tuner-simple.c

1143 lines
29 KiB
C
Raw Normal View History

/*
* i2c tv tuner chip device driver
* controls all those simple 4-control-bytes style tuners.
*
* This "tuner-simple" module was split apart from the original "tuner" module.
*/
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/videodev2.h>
#include <media/tuner.h>
#include <media/v4l2-common.h>
#include <media/tuner-types.h>
#include "tuner-i2c.h"
#include "tuner-simple.h"
static int debug;
module_param(debug, int, 0644);
MODULE_PARM_DESC(debug, "enable verbose debug messages");
#define TUNER_SIMPLE_MAX 64
static unsigned int simple_devcount;
static int offset;
module_param(offset, int, 0664);
MODULE_PARM_DESC(offset, "Allows to specify an offset for tuner");
static unsigned int atv_input[TUNER_SIMPLE_MAX] = \
{ [0 ... (TUNER_SIMPLE_MAX-1)] = 0 };
static unsigned int dtv_input[TUNER_SIMPLE_MAX] = \
{ [0 ... (TUNER_SIMPLE_MAX-1)] = 0 };
module_param_array(atv_input, int, NULL, 0644);
module_param_array(dtv_input, int, NULL, 0644);
MODULE_PARM_DESC(atv_input, "specify atv rf input, 0 for autoselect");
MODULE_PARM_DESC(dtv_input, "specify dtv rf input, 0 for autoselect");
/* ---------------------------------------------------------------------- */
/* tv standard selection for Temic 4046 FM5
this value takes the low bits of control byte 2
from datasheet Rev.01, Feb.00
standard BG I L L2 D
picture IF 38.9 38.9 38.9 33.95 38.9
sound 1 33.4 32.9 32.4 40.45 32.4
sound 2 33.16
NICAM 33.05 32.348 33.05 33.05
*/
#define TEMIC_SET_PAL_I 0x05
#define TEMIC_SET_PAL_DK 0x09
#define TEMIC_SET_PAL_L 0x0a /* SECAM ? */
#define TEMIC_SET_PAL_L2 0x0b /* change IF ! */
#define TEMIC_SET_PAL_BG 0x0c
/* tv tuner system standard selection for Philips FQ1216ME
this value takes the low bits of control byte 2
from datasheet "1999 Nov 16" (supersedes "1999 Mar 23")
standard BG DK I L L`
picture carrier 38.90 38.90 38.90 38.90 33.95
colour 34.47 34.47 34.47 34.47 38.38
sound 1 33.40 32.40 32.90 32.40 40.45
sound 2 33.16 - - - -
NICAM 33.05 33.05 32.35 33.05 39.80
*/
#define PHILIPS_SET_PAL_I 0x01 /* Bit 2 always zero !*/
#define PHILIPS_SET_PAL_BGDK 0x09
#define PHILIPS_SET_PAL_L2 0x0a
#define PHILIPS_SET_PAL_L 0x0b
/* system switching for Philips FI1216MF MK2
from datasheet "1996 Jul 09",
standard BG L L'
picture carrier 38.90 38.90 33.95
colour 34.47 34.37 38.38
sound 1 33.40 32.40 40.45
sound 2 33.16 - -
NICAM 33.05 33.05 39.80
*/
#define PHILIPS_MF_SET_STD_BG 0x01 /* Bit 2 must be zero, Bit 3 is system output */
#define PHILIPS_MF_SET_STD_L 0x03 /* Used on Secam France */
#define PHILIPS_MF_SET_STD_LC 0x02 /* Used on SECAM L' */
/* Control byte */
#define TUNER_RATIO_MASK 0x06 /* Bit cb1:cb2 */
#define TUNER_RATIO_SELECT_50 0x00
#define TUNER_RATIO_SELECT_32 0x02
#define TUNER_RATIO_SELECT_166 0x04
#define TUNER_RATIO_SELECT_62 0x06
#define TUNER_CHARGE_PUMP 0x40 /* Bit cb6 */
/* Status byte */
#define TUNER_POR 0x80
#define TUNER_FL 0x40
#define TUNER_MODE 0x38
#define TUNER_AFC 0x07
#define TUNER_SIGNAL 0x07
#define TUNER_STEREO 0x10
#define TUNER_PLL_LOCKED 0x40
#define TUNER_STEREO_MK3 0x04
static DEFINE_MUTEX(tuner_simple_list_mutex);
static LIST_HEAD(hybrid_tuner_instance_list);
struct tuner_simple_priv {
unsigned int nr;
u16 last_div;
struct tuner_i2c_props i2c_props;
struct list_head hybrid_tuner_instance_list;
unsigned int type;
struct tunertype *tun;
u32 frequency;
u32 bandwidth;
bool radio_mode;
};
/* ---------------------------------------------------------------------- */
static int tuner_read_status(struct dvb_frontend *fe)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
unsigned char byte;
if (1 != tuner_i2c_xfer_recv(&priv->i2c_props, &byte, 1))
return 0;
return byte;
}
static inline int tuner_signal(const int status)
{
return (status & TUNER_SIGNAL) << 13;
}
static inline int tuner_stereo(const int type, const int status)
{
switch (type) {
case TUNER_PHILIPS_FM1216ME_MK3:
case TUNER_PHILIPS_FM1236_MK3:
case TUNER_PHILIPS_FM1256_IH3:
case TUNER_LG_NTSC_TAPE:
case TUNER_TCL_MF02GIP_5N:
return ((status & TUNER_SIGNAL) == TUNER_STEREO_MK3);
case TUNER_PHILIPS_FM1216MK5:
return status | TUNER_STEREO;
default:
return status & TUNER_STEREO;
}
}
static inline int tuner_islocked(const int status)
{
return (status & TUNER_FL);
}
static inline int tuner_afcstatus(const int status)
{
return (status & TUNER_AFC) - 2;
}
static int simple_get_status(struct dvb_frontend *fe, u32 *status)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
int tuner_status;
if (priv->i2c_props.adap == NULL)
return -EINVAL;
tuner_status = tuner_read_status(fe);
*status = 0;
if (tuner_islocked(tuner_status))
*status = TUNER_STATUS_LOCKED;
if (tuner_stereo(priv->type, tuner_status))
*status |= TUNER_STATUS_STEREO;
tuner_dbg("AFC Status: %d\n", tuner_afcstatus(tuner_status));
return 0;
}
static int simple_get_rf_strength(struct dvb_frontend *fe, u16 *strength)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
int signal;
if (priv->i2c_props.adap == NULL || !priv->radio_mode)
return -EINVAL;
signal = tuner_signal(tuner_read_status(fe));
*strength = signal;
tuner_dbg("Signal strength: %d\n", signal);
return 0;
}
/* ---------------------------------------------------------------------- */
static inline char *tuner_param_name(enum param_type type)
{
char *name;
switch (type) {
case TUNER_PARAM_TYPE_RADIO:
name = "radio";
break;
case TUNER_PARAM_TYPE_PAL:
name = "pal";
break;
case TUNER_PARAM_TYPE_SECAM:
name = "secam";
break;
case TUNER_PARAM_TYPE_NTSC:
name = "ntsc";
break;
case TUNER_PARAM_TYPE_DIGITAL:
name = "digital";
break;
default:
name = "unknown";
break;
}
return name;
}
static struct tuner_params *simple_tuner_params(struct dvb_frontend *fe,
enum param_type desired_type)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
struct tunertype *tun = priv->tun;
int i;
for (i = 0; i < tun->count; i++)
if (desired_type == tun->params[i].type)
break;
/* use default tuner params if desired_type not available */
if (i == tun->count) {
tuner_dbg("desired params (%s) undefined for tuner %d\n",
tuner_param_name(desired_type), priv->type);
i = 0;
}
tuner_dbg("using tuner params #%d (%s)\n", i,
tuner_param_name(tun->params[i].type));
return &tun->params[i];
}
static int simple_config_lookup(struct dvb_frontend *fe,
struct tuner_params *t_params,
unsigned *frequency, u8 *config, u8 *cb)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
int i;
for (i = 0; i < t_params->count; i++) {
if (*frequency > t_params->ranges[i].limit)
continue;
break;
}
if (i == t_params->count) {
tuner_dbg("frequency out of range (%d > %d)\n",
*frequency, t_params->ranges[i - 1].limit);
*frequency = t_params->ranges[--i].limit;
}
*config = t_params->ranges[i].config;
*cb = t_params->ranges[i].cb;
tuner_dbg("freq = %d.%02d (%d), range = %d, config = 0x%02x, cb = 0x%02x\n",
*frequency / 16, *frequency % 16 * 100 / 16, *frequency,
i, *config, *cb);
return i;
}
/* ---------------------------------------------------------------------- */
static void simple_set_rf_input(struct dvb_frontend *fe,
u8 *config, u8 *cb, unsigned int rf)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
switch (priv->type) {
case TUNER_PHILIPS_TUV1236D:
switch (rf) {
case 1:
*cb |= 0x08;
break;
default:
*cb &= ~0x08;
break;
}
break;
case TUNER_PHILIPS_FCV1236D:
switch (rf) {
case 1:
*cb |= 0x01;
break;
default:
*cb &= ~0x01;
break;
}
break;
default:
break;
}
}
static int simple_std_setup(struct dvb_frontend *fe,
struct analog_parameters *params,
u8 *config, u8 *cb)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
int rc;
/* tv norm specific stuff for multi-norm tuners */
switch (priv->type) {
case TUNER_PHILIPS_SECAM: /* FI1216MF */
/* 0x01 -> ??? no change ??? */
/* 0x02 -> PAL BDGHI / SECAM L */
/* 0x04 -> ??? PAL others / SECAM others ??? */
*cb &= ~0x03;
if (params->std & V4L2_STD_SECAM_L)
/* also valid for V4L2_STD_SECAM */
*cb |= PHILIPS_MF_SET_STD_L;
else if (params->std & V4L2_STD_SECAM_LC)
*cb |= PHILIPS_MF_SET_STD_LC;
else /* V4L2_STD_B|V4L2_STD_GH */
*cb |= PHILIPS_MF_SET_STD_BG;
break;
case TUNER_TEMIC_4046FM5:
*cb &= ~0x0f;
if (params->std & V4L2_STD_PAL_BG) {
*cb |= TEMIC_SET_PAL_BG;
} else if (params->std & V4L2_STD_PAL_I) {
*cb |= TEMIC_SET_PAL_I;
} else if (params->std & V4L2_STD_PAL_DK) {
*cb |= TEMIC_SET_PAL_DK;
} else if (params->std & V4L2_STD_SECAM_L) {
*cb |= TEMIC_SET_PAL_L;
}
break;
case TUNER_PHILIPS_FQ1216ME:
*cb &= ~0x0f;
if (params->std & (V4L2_STD_PAL_BG|V4L2_STD_PAL_DK)) {
*cb |= PHILIPS_SET_PAL_BGDK;
} else if (params->std & V4L2_STD_PAL_I) {
*cb |= PHILIPS_SET_PAL_I;
} else if (params->std & V4L2_STD_SECAM_L) {
*cb |= PHILIPS_SET_PAL_L;
}
break;
case TUNER_PHILIPS_FCV1236D:
/* 0x00 -> ATSC antenna input 1 */
/* 0x01 -> ATSC antenna input 2 */
/* 0x02 -> NTSC antenna input 1 */
/* 0x03 -> NTSC antenna input 2 */
*cb &= ~0x03;
if (!(params->std & V4L2_STD_ATSC))
*cb |= 2;
break;
case TUNER_MICROTUNE_4042FI5:
/* Set the charge pump for fast tuning */
*config |= TUNER_CHARGE_PUMP;
break;
case TUNER_PHILIPS_TUV1236D:
{
V4L/DVB (10527): tuner: fix TUV1236D analog/digital setup As reported by David Engel <david@istwok.net>, ATSC115 doesn't work fine with mythtv. This software opens both analog and dvb interfaces of saa7134. What happens is that some tuner commands are going to the wrong place, as shown at the logs: Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: using tuner params #0 (ntsc) Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808 Feb 12 20:37:48 opus kernel: tuner 1-0061: tv freq set to 67.25 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: using tuner params #0 (ntsc) Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: tv 0x07 0x10 0xce 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: tv 0x07 0x10 0xce 0x01 This happens due to a hack at TUV1236D analog setup, where it replaces tuner address, at 0x61 for 0x0a, in order to save a few memory bytes. The code assumes that nobody else would try to access the tuner during that setup, but the point is that there's no lock to protect such access. So, this opens the possibility of race conditions to happen. Instead of hacking tuner address, this patch uses a temporary var with the proper tuner value to be used during the setup. This should save the issue, although we should consider to write some analog/digital lock at saa7134 driver. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-02-13 19:24:34 +08:00
struct tuner_i2c_props i2c = priv->i2c_props;
/* 0x40 -> ATSC antenna input 1 */
/* 0x48 -> ATSC antenna input 2 */
/* 0x00 -> NTSC antenna input 1 */
/* 0x08 -> NTSC antenna input 2 */
u8 buffer[4] = { 0x14, 0x00, 0x17, 0x00};
*cb &= ~0x40;
if (params->std & V4L2_STD_ATSC) {
*cb |= 0x40;
buffer[1] = 0x04;
}
/* set to the correct mode (analog or digital) */
V4L/DVB (10527): tuner: fix TUV1236D analog/digital setup As reported by David Engel <david@istwok.net>, ATSC115 doesn't work fine with mythtv. This software opens both analog and dvb interfaces of saa7134. What happens is that some tuner commands are going to the wrong place, as shown at the logs: Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: using tuner params #0 (ntsc) Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808 Feb 12 20:37:48 opus kernel: tuner 1-0061: tv freq set to 67.25 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: using tuner params #0 (ntsc) Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: tv 0x07 0x10 0xce 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: tv 0x07 0x10 0xce 0x01 This happens due to a hack at TUV1236D analog setup, where it replaces tuner address, at 0x61 for 0x0a, in order to save a few memory bytes. The code assumes that nobody else would try to access the tuner during that setup, but the point is that there's no lock to protect such access. So, this opens the possibility of race conditions to happen. Instead of hacking tuner address, this patch uses a temporary var with the proper tuner value to be used during the setup. This should save the issue, although we should consider to write some analog/digital lock at saa7134 driver. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-02-13 19:24:34 +08:00
i2c.addr = 0x0a;
rc = tuner_i2c_xfer_send(&i2c, &buffer[0], 2);
if (2 != rc)
tuner_warn("i2c i/o error: rc == %d (should be 2)\n",
rc);
V4L/DVB (10527): tuner: fix TUV1236D analog/digital setup As reported by David Engel <david@istwok.net>, ATSC115 doesn't work fine with mythtv. This software opens both analog and dvb interfaces of saa7134. What happens is that some tuner commands are going to the wrong place, as shown at the logs: Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: using tuner params #0 (ntsc) Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808 Feb 12 20:37:48 opus kernel: tuner 1-0061: tv freq set to 67.25 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: using tuner params #0 (ntsc) Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808 Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: tv 0x07 0x10 0xce 0x01 Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: tv 0x07 0x10 0xce 0x01 This happens due to a hack at TUV1236D analog setup, where it replaces tuner address, at 0x61 for 0x0a, in order to save a few memory bytes. The code assumes that nobody else would try to access the tuner during that setup, but the point is that there's no lock to protect such access. So, this opens the possibility of race conditions to happen. Instead of hacking tuner address, this patch uses a temporary var with the proper tuner value to be used during the setup. This should save the issue, although we should consider to write some analog/digital lock at saa7134 driver. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-02-13 19:24:34 +08:00
rc = tuner_i2c_xfer_send(&i2c, &buffer[2], 2);
if (2 != rc)
tuner_warn("i2c i/o error: rc == %d (should be 2)\n",
rc);
break;
}
}
if (atv_input[priv->nr])
simple_set_rf_input(fe, config, cb, atv_input[priv->nr]);
return 0;
}
static int simple_set_aux_byte(struct dvb_frontend *fe, u8 config, u8 aux)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
int rc;
u8 buffer[2];
buffer[0] = (config & ~0x38) | 0x18;
buffer[1] = aux;
tuner_dbg("setting aux byte: 0x%02x 0x%02x\n", buffer[0], buffer[1]);
rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer, 2);
if (2 != rc)
tuner_warn("i2c i/o error: rc == %d (should be 2)\n", rc);
return rc == 2 ? 0 : rc;
}
static int simple_post_tune(struct dvb_frontend *fe, u8 *buffer,
u16 div, u8 config, u8 cb)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
int rc;
switch (priv->type) {
case TUNER_LG_TDVS_H06XF:
simple_set_aux_byte(fe, config, 0x20);
break;
case TUNER_PHILIPS_FQ1216LME_MK3:
simple_set_aux_byte(fe, config, 0x60); /* External AGC */
break;
case TUNER_MICROTUNE_4042FI5:
{
/* FIXME - this may also work for other tuners */
unsigned long timeout = jiffies + msecs_to_jiffies(1);
u8 status_byte = 0;
/* Wait until the PLL locks */
for (;;) {
if (time_after(jiffies, timeout))
return 0;
rc = tuner_i2c_xfer_recv(&priv->i2c_props,
&status_byte, 1);
if (1 != rc) {
tuner_warn("i2c i/o read error: rc == %d (should be 1)\n",
rc);
break;
}
if (status_byte & TUNER_PLL_LOCKED)
break;
udelay(10);
}
/* Set the charge pump for optimized phase noise figure */
config &= ~TUNER_CHARGE_PUMP;
buffer[0] = (div>>8) & 0x7f;
buffer[1] = div & 0xff;
buffer[2] = config;
buffer[3] = cb;
tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n",
buffer[0], buffer[1], buffer[2], buffer[3]);
rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer, 4);
if (4 != rc)
tuner_warn("i2c i/o error: rc == %d (should be 4)\n",
rc);
break;
}
}
return 0;
}
static int simple_radio_bandswitch(struct dvb_frontend *fe, u8 *buffer)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
switch (priv->type) {
case TUNER_TENA_9533_DI:
case TUNER_YMEC_TVF_5533MF:
tuner_dbg("This tuner doesn't have FM. Most cards have a TEA5767 for FM\n");
return 0;
case TUNER_PHILIPS_FM1216ME_MK3:
case TUNER_PHILIPS_FM1236_MK3:
case TUNER_PHILIPS_FMD1216ME_MK3:
case TUNER_PHILIPS_FMD1216MEX_MK3:
case TUNER_LG_NTSC_TAPE:
case TUNER_PHILIPS_FM1256_IH3:
case TUNER_TCL_MF02GIP_5N:
buffer[3] = 0x19;
break;
case TUNER_PHILIPS_FM1216MK5:
buffer[2] = 0x88;
buffer[3] = 0x09;
break;
case TUNER_TNF_5335MF:
buffer[3] = 0x11;
break;
case TUNER_LG_PAL_FM:
buffer[3] = 0xa5;
break;
case TUNER_THOMSON_DTT761X:
buffer[3] = 0x39;
break;
case TUNER_PHILIPS_FQ1216LME_MK3:
case TUNER_PHILIPS_FQ1236_MK5:
tuner_err("This tuner doesn't have FM\n");
/* Set the low band for sanity, since it covers 88-108 MHz */
buffer[3] = 0x01;
break;
case TUNER_MICROTUNE_4049FM5:
default:
buffer[3] = 0xa4;
break;
}
return 0;
}
/* ---------------------------------------------------------------------- */
static int simple_set_tv_freq(struct dvb_frontend *fe,
struct analog_parameters *params)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
u8 config, cb;
u16 div;
u8 buffer[4];
int rc, IFPCoff, i;
enum param_type desired_type;
struct tuner_params *t_params;
/* IFPCoff = Video Intermediate Frequency - Vif:
940 =16*58.75 NTSC/J (Japan)
732 =16*45.75 M/N STD
704 =16*44 ATSC (at DVB code)
632 =16*39.50 I U.K.
622.4=16*38.90 B/G D/K I, L STD
592 =16*37.00 D China
590 =16.36.875 B Australia
543.2=16*33.95 L' STD
171.2=16*10.70 FM Radio (at set_radio_freq)
*/
if (params->std == V4L2_STD_NTSC_M_JP) {
IFPCoff = 940;
desired_type = TUNER_PARAM_TYPE_NTSC;
} else if ((params->std & V4L2_STD_MN) &&
!(params->std & ~V4L2_STD_MN)) {
IFPCoff = 732;
desired_type = TUNER_PARAM_TYPE_NTSC;
} else if (params->std == V4L2_STD_SECAM_LC) {
IFPCoff = 543;
desired_type = TUNER_PARAM_TYPE_SECAM;
} else {
IFPCoff = 623;
desired_type = TUNER_PARAM_TYPE_PAL;
}
t_params = simple_tuner_params(fe, desired_type);
i = simple_config_lookup(fe, t_params, &params->frequency,
&config, &cb);
div = params->frequency + IFPCoff + offset;
tuner_dbg("Freq= %d.%02d MHz, V_IF=%d.%02d MHz, Offset=%d.%02d MHz, div=%0d\n",
params->frequency / 16, params->frequency % 16 * 100 / 16,
IFPCoff / 16, IFPCoff % 16 * 100 / 16,
offset / 16, offset % 16 * 100 / 16, div);
/* tv norm specific stuff for multi-norm tuners */
simple_std_setup(fe, params, &config, &cb);
if (t_params->cb_first_if_lower_freq && div < priv->last_div) {
buffer[0] = config;
buffer[1] = cb;
buffer[2] = (div>>8) & 0x7f;
buffer[3] = div & 0xff;
} else {
buffer[0] = (div>>8) & 0x7f;
buffer[1] = div & 0xff;
buffer[2] = config;
buffer[3] = cb;
}
priv->last_div = div;
if (t_params->has_tda9887) {
struct v4l2_priv_tun_config tda9887_cfg;
int tda_config = 0;
int is_secam_l = (params->std & (V4L2_STD_SECAM_L |
V4L2_STD_SECAM_LC)) &&
!(params->std & ~(V4L2_STD_SECAM_L |
V4L2_STD_SECAM_LC));
tda9887_cfg.tuner = TUNER_TDA9887;
tda9887_cfg.priv = &tda_config;
if (params->std == V4L2_STD_SECAM_LC) {
if (t_params->port1_active ^ t_params->port1_invert_for_secam_lc)
tda_config |= TDA9887_PORT1_ACTIVE;
if (t_params->port2_active ^ t_params->port2_invert_for_secam_lc)
tda_config |= TDA9887_PORT2_ACTIVE;
} else {
if (t_params->port1_active)
tda_config |= TDA9887_PORT1_ACTIVE;
if (t_params->port2_active)
tda_config |= TDA9887_PORT2_ACTIVE;
}
if (t_params->intercarrier_mode)
tda_config |= TDA9887_INTERCARRIER;
if (is_secam_l) {
if (i == 0 && t_params->default_top_secam_low)
tda_config |= TDA9887_TOP(t_params->default_top_secam_low);
else if (i == 1 && t_params->default_top_secam_mid)
tda_config |= TDA9887_TOP(t_params->default_top_secam_mid);
else if (t_params->default_top_secam_high)
tda_config |= TDA9887_TOP(t_params->default_top_secam_high);
} else {
if (i == 0 && t_params->default_top_low)
tda_config |= TDA9887_TOP(t_params->default_top_low);
else if (i == 1 && t_params->default_top_mid)
tda_config |= TDA9887_TOP(t_params->default_top_mid);
else if (t_params->default_top_high)
tda_config |= TDA9887_TOP(t_params->default_top_high);
}
if (t_params->default_pll_gating_18)
tda_config |= TDA9887_GATING_18;
i2c_clients_command(priv->i2c_props.adap, TUNER_SET_CONFIG,
&tda9887_cfg);
}
tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n",
buffer[0], buffer[1], buffer[2], buffer[3]);
rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer, 4);
if (4 != rc)
tuner_warn("i2c i/o error: rc == %d (should be 4)\n", rc);
simple_post_tune(fe, &buffer[0], div, config, cb);
return 0;
}
static int simple_set_radio_freq(struct dvb_frontend *fe,
struct analog_parameters *params)
{
struct tunertype *tun;
struct tuner_simple_priv *priv = fe->tuner_priv;
u8 buffer[4];
u16 div;
int rc, j;
struct tuner_params *t_params;
unsigned int freq = params->frequency;
bool mono = params->audmode == V4L2_TUNER_MODE_MONO;
tun = priv->tun;
V4L/DVB (5978): tuner: Better tuner radio support Add radio support for the Thomson DTT7612 tuner. This tuner uses a different 1st intermediate frequency than the other radio tuners supported (a lot of NTSC radio tuners probably need this change too). Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for radio reception. The radio frequency setting code in tuner-simple now uses this field, instead of a special case select() block for each tuner with radio support. The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1 in tuner-types.c. The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and fm_gain_normal = 1. Add some defines for tda9887 bits that control IF setting in radio mode. Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz radio IF. Fix the way tda9887 radio options work. The driver was modifying the default radio mode config templates based on the TDA9887_XXXX flags. This means that _all_ tuners would get the same settings. If you had a one tuner than used TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the tda9987 driver just checks if tuner mode is radio and then applies the config settings directly to the data being sent, just like how all the TV mode settings already work. The PLL setting math is made a little more accurate. And a grammar error in a printk is fixed. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-04 05:32:38 +08:00
for (j = tun->count-1; j > 0; j--)
if (tun->params[j].type == TUNER_PARAM_TYPE_RADIO)
break;
/* default t_params (j=0) will be used if desired type wasn't found */
t_params = &tun->params[j];
V4L/DVB (5978): tuner: Better tuner radio support Add radio support for the Thomson DTT7612 tuner. This tuner uses a different 1st intermediate frequency than the other radio tuners supported (a lot of NTSC radio tuners probably need this change too). Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for radio reception. The radio frequency setting code in tuner-simple now uses this field, instead of a special case select() block for each tuner with radio support. The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1 in tuner-types.c. The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and fm_gain_normal = 1. Add some defines for tda9887 bits that control IF setting in radio mode. Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz radio IF. Fix the way tda9887 radio options work. The driver was modifying the default radio mode config templates based on the TDA9887_XXXX flags. This means that _all_ tuners would get the same settings. If you had a one tuner than used TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the tda9987 driver just checks if tuner mode is radio and then applies the config settings directly to the data being sent, just like how all the TV mode settings already work. The PLL setting math is made a little more accurate. And a grammar error in a printk is fixed. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-04 05:32:38 +08:00
/* Select Radio 1st IF used */
switch (t_params->radio_if) {
V4L/DVB (5978): tuner: Better tuner radio support Add radio support for the Thomson DTT7612 tuner. This tuner uses a different 1st intermediate frequency than the other radio tuners supported (a lot of NTSC radio tuners probably need this change too). Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for radio reception. The radio frequency setting code in tuner-simple now uses this field, instead of a special case select() block for each tuner with radio support. The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1 in tuner-types.c. The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and fm_gain_normal = 1. Add some defines for tda9887 bits that control IF setting in radio mode. Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz radio IF. Fix the way tda9887 radio options work. The driver was modifying the default radio mode config templates based on the TDA9887_XXXX flags. This means that _all_ tuners would get the same settings. If you had a one tuner than used TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the tda9987 driver just checks if tuner mode is radio and then applies the config settings directly to the data being sent, just like how all the TV mode settings already work. The PLL setting math is made a little more accurate. And a grammar error in a printk is fixed. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-04 05:32:38 +08:00
case 0: /* 10.7 MHz */
freq += (unsigned int)(10.7*16000);
break;
V4L/DVB (5978): tuner: Better tuner radio support Add radio support for the Thomson DTT7612 tuner. This tuner uses a different 1st intermediate frequency than the other radio tuners supported (a lot of NTSC radio tuners probably need this change too). Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for radio reception. The radio frequency setting code in tuner-simple now uses this field, instead of a special case select() block for each tuner with radio support. The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1 in tuner-types.c. The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and fm_gain_normal = 1. Add some defines for tda9887 bits that control IF setting in radio mode. Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz radio IF. Fix the way tda9887 radio options work. The driver was modifying the default radio mode config templates based on the TDA9887_XXXX flags. This means that _all_ tuners would get the same settings. If you had a one tuner than used TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the tda9987 driver just checks if tuner mode is radio and then applies the config settings directly to the data being sent, just like how all the TV mode settings already work. The PLL setting math is made a little more accurate. And a grammar error in a printk is fixed. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-04 05:32:38 +08:00
case 1: /* 33.3 MHz */
freq += (unsigned int)(33.3*16000);
break;
case 2: /* 41.3 MHz */
freq += (unsigned int)(41.3*16000);
break;
default:
tuner_warn("Unsupported radio_if value %d\n",
t_params->radio_if);
return 0;
}
buffer[2] = (t_params->ranges[0].config & ~TUNER_RATIO_MASK) |
V4L/DVB (5978): tuner: Better tuner radio support Add radio support for the Thomson DTT7612 tuner. This tuner uses a different 1st intermediate frequency than the other radio tuners supported (a lot of NTSC radio tuners probably need this change too). Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for radio reception. The radio frequency setting code in tuner-simple now uses this field, instead of a special case select() block for each tuner with radio support. The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1 in tuner-types.c. The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and fm_gain_normal = 1. Add some defines for tda9887 bits that control IF setting in radio mode. Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz radio IF. Fix the way tda9887 radio options work. The driver was modifying the default radio mode config templates based on the TDA9887_XXXX flags. This means that _all_ tuners would get the same settings. If you had a one tuner than used TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the tda9987 driver just checks if tuner mode is radio and then applies the config settings directly to the data being sent, just like how all the TV mode settings already work. The PLL setting math is made a little more accurate. And a grammar error in a printk is fixed. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-04 05:32:38 +08:00
TUNER_RATIO_SELECT_50; /* 50 kHz step */
/* Bandswitch byte */
simple_radio_bandswitch(fe, &buffer[0]);
V4L/DVB (5978): tuner: Better tuner radio support Add radio support for the Thomson DTT7612 tuner. This tuner uses a different 1st intermediate frequency than the other radio tuners supported (a lot of NTSC radio tuners probably need this change too). Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for radio reception. The radio frequency setting code in tuner-simple now uses this field, instead of a special case select() block for each tuner with radio support. The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1 in tuner-types.c. The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and fm_gain_normal = 1. Add some defines for tda9887 bits that control IF setting in radio mode. Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz radio IF. Fix the way tda9887 radio options work. The driver was modifying the default radio mode config templates based on the TDA9887_XXXX flags. This means that _all_ tuners would get the same settings. If you had a one tuner than used TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the tda9987 driver just checks if tuner mode is radio and then applies the config settings directly to the data being sent, just like how all the TV mode settings already work. The PLL setting math is made a little more accurate. And a grammar error in a printk is fixed. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-04 05:32:38 +08:00
/* Convert from 1/16 kHz V4L steps to 1/20 MHz (=50 kHz) PLL steps
freq * (1 Mhz / 16000 V4L steps) * (20 PLL steps / 1 MHz) =
freq * (1/800) */
div = (freq + 400) / 800;
if (t_params->cb_first_if_lower_freq && div < priv->last_div) {
buffer[0] = buffer[2];
buffer[1] = buffer[3];
buffer[2] = (div>>8) & 0x7f;
buffer[3] = div & 0xff;
} else {
buffer[0] = (div>>8) & 0x7f;
buffer[1] = div & 0xff;
}
tuner_dbg("radio 0x%02x 0x%02x 0x%02x 0x%02x\n",
buffer[0], buffer[1], buffer[2], buffer[3]);
priv->last_div = div;
if (t_params->has_tda9887) {
int config = 0;
struct v4l2_priv_tun_config tda9887_cfg;
tda9887_cfg.tuner = TUNER_TDA9887;
tda9887_cfg.priv = &config;
if (t_params->port1_active &&
!t_params->port1_fm_high_sensitivity)
config |= TDA9887_PORT1_ACTIVE;
if (t_params->port2_active &&
!t_params->port2_fm_high_sensitivity)
config |= TDA9887_PORT2_ACTIVE;
if (t_params->intercarrier_mode)
config |= TDA9887_INTERCARRIER;
if (t_params->port1_set_for_fm_mono && mono)
config &= ~TDA9887_PORT1_ACTIVE;
if (t_params->fm_gain_normal)
config |= TDA9887_GAIN_NORMAL;
if (t_params->radio_if == 2)
V4L/DVB (5978): tuner: Better tuner radio support Add radio support for the Thomson DTT7612 tuner. This tuner uses a different 1st intermediate frequency than the other radio tuners supported (a lot of NTSC radio tuners probably need this change too). Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for radio reception. The radio frequency setting code in tuner-simple now uses this field, instead of a special case select() block for each tuner with radio support. The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1 in tuner-types.c. The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and fm_gain_normal = 1. Add some defines for tda9887 bits that control IF setting in radio mode. Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz radio IF. Fix the way tda9887 radio options work. The driver was modifying the default radio mode config templates based on the TDA9887_XXXX flags. This means that _all_ tuners would get the same settings. If you had a one tuner than used TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the tda9987 driver just checks if tuner mode is radio and then applies the config settings directly to the data being sent, just like how all the TV mode settings already work. The PLL setting math is made a little more accurate. And a grammar error in a printk is fixed. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-04 05:32:38 +08:00
config |= TDA9887_RIF_41_3;
i2c_clients_command(priv->i2c_props.adap, TUNER_SET_CONFIG,
&tda9887_cfg);
}
rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer, 4);
if (4 != rc)
tuner_warn("i2c i/o error: rc == %d (should be 4)\n", rc);
/* Write AUX byte */
switch (priv->type) {
case TUNER_PHILIPS_FM1216ME_MK3:
buffer[2] = 0x98;
buffer[3] = 0x20; /* set TOP AGC */
rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer, 4);
if (4 != rc)
tuner_warn("i2c i/o error: rc == %d (should be 4)\n", rc);
break;
}
return 0;
}
static int simple_set_params(struct dvb_frontend *fe,
struct analog_parameters *params)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
int ret = -EINVAL;
if (priv->i2c_props.adap == NULL)
return -EINVAL;
switch (params->mode) {
case V4L2_TUNER_RADIO:
priv->radio_mode = true;
ret = simple_set_radio_freq(fe, params);
priv->frequency = params->frequency * 125 / 2;
break;
case V4L2_TUNER_ANALOG_TV:
case V4L2_TUNER_DIGITAL_TV:
priv->radio_mode = false;
ret = simple_set_tv_freq(fe, params);
priv->frequency = params->frequency * 62500;
break;
}
priv->bandwidth = 0;
return ret;
}
static void simple_set_dvb(struct dvb_frontend *fe, u8 *buf,
const u32 delsys,
const u32 frequency,
const u32 bandwidth)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
switch (priv->type) {
case TUNER_PHILIPS_FMD1216ME_MK3:
case TUNER_PHILIPS_FMD1216MEX_MK3:
if (bandwidth == 8000000 &&
frequency >= 158870000)
buf[3] |= 0x08;
break;
case TUNER_PHILIPS_TD1316:
/* determine band */
buf[3] |= (frequency < 161000000) ? 1 :
(frequency < 444000000) ? 2 : 4;
/* setup PLL filter */
if (bandwidth == 8000000)
buf[3] |= 1 << 3;
break;
case TUNER_PHILIPS_TUV1236D:
case TUNER_PHILIPS_FCV1236D:
{
unsigned int new_rf;
if (dtv_input[priv->nr])
new_rf = dtv_input[priv->nr];
else
switch (delsys) {
case SYS_DVBC_ANNEX_B:
new_rf = 1;
break;
case SYS_ATSC:
default:
new_rf = 0;
break;
}
simple_set_rf_input(fe, &buf[2], &buf[3], new_rf);
break;
}
default:
break;
}
}
static u32 simple_dvb_configure(struct dvb_frontend *fe, u8 *buf,
const u32 delsys,
const u32 freq,
const u32 bw)
{
/* This function returns the tuned frequency on success, 0 on error */
struct tuner_simple_priv *priv = fe->tuner_priv;
struct tunertype *tun = priv->tun;
struct tuner_params *t_params;
u8 config, cb;
u32 div;
int ret;
u32 frequency = freq / 62500;
V4L/DVB (10170): tuner-simple: prevent possible OOPS caused by divide by zero error A user reported the following OOPS with his pcHDTV HD5500 card, which uses a cx88 PCI bridge with a LG-TDVS-H06xF frontend module, made up of a TUA6034 tuner, TDA988x IF demod, and LG DT3303 ATSC/QAM demod. Somehow, tuner-core gets loaded before the digital driver configures the tuner, and tuner-core somehow incorrectly sets the tuner type to LG NTSC (TAPE series) instead of LG TDVS-H06xF. This tuner type does not have the tuning stepsize defined, so an OOPS occurs during the digital tune function. We still dont know how the type gets set incorrectly in the first place. The user has a tainted kernel with a binary nividia module, which COULD have something to do with this, but it's hard to say for sure. Nevertheless, to avoid this division by zero, we should check that stepsize is defined. If stepsize is not defined, print an error and bail out on the tune request. cx8800 0000:05:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 cx88[0]: subsystem: 7063:5500, board: pcHDTV HD5500 HDTV [card=47,autodetected], frontend(s): 1 cx88[0]: TV tuner type 47, Radio tuner type -1 tuner' 2-0043: chip found @ 0x86 (cx88[0]) tda9887 2-0043: creating new instance tda9887 2-0043: tda988[5/6/7] found tuner' 2-0061: chip found @ 0xc2 (cx88[0]) tuner-simple 2-0061: creating new instance tuner-simple 2-0061: type set to 47 (LG NTSC (TAPE series)) cx88[0]/0: found at 0000:05:01.0, rev: 5, irq: 19, latency: 32, mmio: 0xea000000 cx88[0]/0: registered device video1 [v4l2] cx88[0]/0: registered device vbi1 cx88_audio 0000:05:01.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19 cx88[0]/1: CX88x/0: ALSA support for cx2388x boards cx88[0]/2: cx2388x 8802 Driver Manager cx88-mpeg driver manager 0000:05:01.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 cx88[0]/2: found at 0000:05:01.2, rev: 5, irq: 19, latency: 32, mmio: 0xec000000 cx8802_probe() allocating 1 frontend(s) cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 7063:5500, board: pcHDTV HD5500 HDTV [card=47] cx88[0]/2: cx2388x based DVB/ATSC card tuner-simple 2-0061: attaching existing instance tuner-simple 2-0061: type set to 64 (LG NTSC (TAPE series)) tda9887 2-0043: attaching existing instance DVB: registering new adapter (cx88[0]) DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)... [snip] stepsize=0 divide error: 0000 [1] SMP CPU 1 Modules linked in: nls_utf8 fuse sco bridge stp bnep l2cap bluetooth sunrpc nf_conntrack_netbios_ns nf_conntrack_ftp ip6t_REJECT nf_conntrack_ipv6 ip6table_filter ip6_tables ipv6 cpufreq_ondemand acpi_cpufreq freq_table xfs lgdt330x dm_multipath cx88_dvb cx88_vp3054_i2c uinput tda9887 tda8290 snd_emu10k1_synth snd_emux_synth snd_seq_virmidi snd_seq_midi_emul tuner_simple tuner_types tuner msp3400 cx8800 cx88_alsa cx8802 snd_emu10k1 cx88xx snd_rawmidi snd_ac97_codec ir_common ac97_bus saa7115 snd_seq_dummy snd_seq_oss snd_seq_midi_event videobuf_dvb snd_seq dvb_core snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_device videobuf_dma_sg ppdev parport_pc snd_timer videobuf_core snd_page_alloc btcx_risc emu10k1_gp ivtv i2c_algo_bit cx2341x snd_util_mem snd_hwdep nvidia(P) gameport v4l2_common i2c_i801 snd soundcore parport videodev v4l1_compat v4l2_compat_ioctl32 tveeprom i2c_core pcspkr iTCO_wdt iTCO_vendor_support sky2 joydev floppy shpchp ata_generic pata_acpi pata_jmicron [last unloaded: microcode] Pid: 3553, comm: kdvb-ad-0-fe-0 Tainted: P 2.6.27.9-159.fc10.x86_64 #1 RIP: 0010:[<ffffffffa09bc37a>] [<ffffffffa09bc37a>] simple_dvb_calc_regs+0xab/0x281 [tuner_simple] RSP: 0018:ffff8800605dfd30 EFLAGS: 00010246 RAX: 000000000365c040 RBX: ffff8800605dfdb0 RCX: ffff88007acb8c10 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000246 RBP: ffff8800605dfda0 R08: ffff8800605dfba0 R09: 0000000000000082 R10: 00000010e73c9df1 R11: 0000000100000000 R12: ffff88007ac29c00 R13: ffff88007ac29c00 R14: ffff88007acbb408 R15: ffffffffa09b6fb0 FS: 0000000000000000(0000) GS:ffff88007f804880(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00000000004e8f40 CR3: 000000007114e000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process kdvb-ad-0-fe-0 (pid: 3553, threadinfo ffff8800605de000, task ffff88006fca0000) Stack: ffff8800605dfd40 00000000ffffffa1 ffff88007c055860 0000000000000001 ffff8800605dfda0 ffff8800605dfda0 ffff88007acb8c10 ffffffffa004e48c 8e01880000000390 ffff88007acb8c10 ffff88007ac29c00 0000000000000000 Call Trace: [<ffffffffa004e48c>] ? i2c_transfer+0x80/0x8b [i2c_core] [<ffffffffa09bc768>] simple_dvb_set_params+0x3e/0x9b [tuner_simple] [<ffffffffa0a0335a>] lgdt330x_set_parameters+0x188/0x1b9 [lgdt330x] [<ffffffffa08c9116>] dvb_frontend_swzigzag_autotune+0x18e/0x1b5 [dvb_core] [<ffffffffa08c9f6a>] dvb_frontend_swzigzag+0x1bc/0x21e [dvb_core] [<ffffffffa08ca4f4>] dvb_frontend_thread+0x528/0x62b [dvb_core] [<ffffffff810551e1>] ? autoremove_wake_function+0x0/0x38 [<ffffffffa08c9fcc>] ? dvb_frontend_thread+0x0/0x62b [dvb_core] [<ffffffff81054e9b>] kthread+0x49/0x76 [<ffffffff810116e9>] child_rip+0xa/0x11 [<ffffffff81010a07>] ? restore_args+0x0/0x30 [<ffffffff81054e52>] ? kthread+0x0/0x76 [<ffffffff810116df>] ? child_rip+0x0/0x11 Code: 48 8b 05 2a 4e 00 00 41 8b 77 1c 31 d2 0f b7 40 0a 89 f1 03 45 d0 d1 e9 03 0d 23 4e 00 00 69 c0 24 f4 00 00 8d 04 01 48 8b 4d c0 <f7> f6 8a 55 d6 88 53 04 41 89 c4 c1 e8 08 88 43 01 8a 45 d7 44 RIP [<ffffffffa09bc37a>] simple_dvb_calc_regs+0xab/0x281 [tuner_simple] RSP <ffff8800605dfd30> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-01-03 02:55:29 +08:00
if (!tun->stepsize) {
/* tuner-core was loaded before the digital tuner was
* configured and somehow picked the wrong tuner type */
tuner_err("attempt to treat tuner %d (%s) as digital tuner without stepsize defined.\n",
V4L/DVB (10170): tuner-simple: prevent possible OOPS caused by divide by zero error A user reported the following OOPS with his pcHDTV HD5500 card, which uses a cx88 PCI bridge with a LG-TDVS-H06xF frontend module, made up of a TUA6034 tuner, TDA988x IF demod, and LG DT3303 ATSC/QAM demod. Somehow, tuner-core gets loaded before the digital driver configures the tuner, and tuner-core somehow incorrectly sets the tuner type to LG NTSC (TAPE series) instead of LG TDVS-H06xF. This tuner type does not have the tuning stepsize defined, so an OOPS occurs during the digital tune function. We still dont know how the type gets set incorrectly in the first place. The user has a tainted kernel with a binary nividia module, which COULD have something to do with this, but it's hard to say for sure. Nevertheless, to avoid this division by zero, we should check that stepsize is defined. If stepsize is not defined, print an error and bail out on the tune request. cx8800 0000:05:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 cx88[0]: subsystem: 7063:5500, board: pcHDTV HD5500 HDTV [card=47,autodetected], frontend(s): 1 cx88[0]: TV tuner type 47, Radio tuner type -1 tuner' 2-0043: chip found @ 0x86 (cx88[0]) tda9887 2-0043: creating new instance tda9887 2-0043: tda988[5/6/7] found tuner' 2-0061: chip found @ 0xc2 (cx88[0]) tuner-simple 2-0061: creating new instance tuner-simple 2-0061: type set to 47 (LG NTSC (TAPE series)) cx88[0]/0: found at 0000:05:01.0, rev: 5, irq: 19, latency: 32, mmio: 0xea000000 cx88[0]/0: registered device video1 [v4l2] cx88[0]/0: registered device vbi1 cx88_audio 0000:05:01.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19 cx88[0]/1: CX88x/0: ALSA support for cx2388x boards cx88[0]/2: cx2388x 8802 Driver Manager cx88-mpeg driver manager 0000:05:01.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 cx88[0]/2: found at 0000:05:01.2, rev: 5, irq: 19, latency: 32, mmio: 0xec000000 cx8802_probe() allocating 1 frontend(s) cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 7063:5500, board: pcHDTV HD5500 HDTV [card=47] cx88[0]/2: cx2388x based DVB/ATSC card tuner-simple 2-0061: attaching existing instance tuner-simple 2-0061: type set to 64 (LG NTSC (TAPE series)) tda9887 2-0043: attaching existing instance DVB: registering new adapter (cx88[0]) DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)... [snip] stepsize=0 divide error: 0000 [1] SMP CPU 1 Modules linked in: nls_utf8 fuse sco bridge stp bnep l2cap bluetooth sunrpc nf_conntrack_netbios_ns nf_conntrack_ftp ip6t_REJECT nf_conntrack_ipv6 ip6table_filter ip6_tables ipv6 cpufreq_ondemand acpi_cpufreq freq_table xfs lgdt330x dm_multipath cx88_dvb cx88_vp3054_i2c uinput tda9887 tda8290 snd_emu10k1_synth snd_emux_synth snd_seq_virmidi snd_seq_midi_emul tuner_simple tuner_types tuner msp3400 cx8800 cx88_alsa cx8802 snd_emu10k1 cx88xx snd_rawmidi snd_ac97_codec ir_common ac97_bus saa7115 snd_seq_dummy snd_seq_oss snd_seq_midi_event videobuf_dvb snd_seq dvb_core snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_device videobuf_dma_sg ppdev parport_pc snd_timer videobuf_core snd_page_alloc btcx_risc emu10k1_gp ivtv i2c_algo_bit cx2341x snd_util_mem snd_hwdep nvidia(P) gameport v4l2_common i2c_i801 snd soundcore parport videodev v4l1_compat v4l2_compat_ioctl32 tveeprom i2c_core pcspkr iTCO_wdt iTCO_vendor_support sky2 joydev floppy shpchp ata_generic pata_acpi pata_jmicron [last unloaded: microcode] Pid: 3553, comm: kdvb-ad-0-fe-0 Tainted: P 2.6.27.9-159.fc10.x86_64 #1 RIP: 0010:[<ffffffffa09bc37a>] [<ffffffffa09bc37a>] simple_dvb_calc_regs+0xab/0x281 [tuner_simple] RSP: 0018:ffff8800605dfd30 EFLAGS: 00010246 RAX: 000000000365c040 RBX: ffff8800605dfdb0 RCX: ffff88007acb8c10 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000246 RBP: ffff8800605dfda0 R08: ffff8800605dfba0 R09: 0000000000000082 R10: 00000010e73c9df1 R11: 0000000100000000 R12: ffff88007ac29c00 R13: ffff88007ac29c00 R14: ffff88007acbb408 R15: ffffffffa09b6fb0 FS: 0000000000000000(0000) GS:ffff88007f804880(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00000000004e8f40 CR3: 000000007114e000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process kdvb-ad-0-fe-0 (pid: 3553, threadinfo ffff8800605de000, task ffff88006fca0000) Stack: ffff8800605dfd40 00000000ffffffa1 ffff88007c055860 0000000000000001 ffff8800605dfda0 ffff8800605dfda0 ffff88007acb8c10 ffffffffa004e48c 8e01880000000390 ffff88007acb8c10 ffff88007ac29c00 0000000000000000 Call Trace: [<ffffffffa004e48c>] ? i2c_transfer+0x80/0x8b [i2c_core] [<ffffffffa09bc768>] simple_dvb_set_params+0x3e/0x9b [tuner_simple] [<ffffffffa0a0335a>] lgdt330x_set_parameters+0x188/0x1b9 [lgdt330x] [<ffffffffa08c9116>] dvb_frontend_swzigzag_autotune+0x18e/0x1b5 [dvb_core] [<ffffffffa08c9f6a>] dvb_frontend_swzigzag+0x1bc/0x21e [dvb_core] [<ffffffffa08ca4f4>] dvb_frontend_thread+0x528/0x62b [dvb_core] [<ffffffff810551e1>] ? autoremove_wake_function+0x0/0x38 [<ffffffffa08c9fcc>] ? dvb_frontend_thread+0x0/0x62b [dvb_core] [<ffffffff81054e9b>] kthread+0x49/0x76 [<ffffffff810116e9>] child_rip+0xa/0x11 [<ffffffff81010a07>] ? restore_args+0x0/0x30 [<ffffffff81054e52>] ? kthread+0x0/0x76 [<ffffffff810116df>] ? child_rip+0x0/0x11 Code: 48 8b 05 2a 4e 00 00 41 8b 77 1c 31 d2 0f b7 40 0a 89 f1 03 45 d0 d1 e9 03 0d 23 4e 00 00 69 c0 24 f4 00 00 8d 04 01 48 8b 4d c0 <f7> f6 8a 55 d6 88 53 04 41 89 c4 c1 e8 08 88 43 01 8a 45 d7 44 RIP [<ffffffffa09bc37a>] simple_dvb_calc_regs+0xab/0x281 [tuner_simple] RSP <ffff8800605dfd30> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-01-03 02:55:29 +08:00
priv->type, priv->tun->name);
return 0; /* failure */
}
t_params = simple_tuner_params(fe, TUNER_PARAM_TYPE_DIGITAL);
ret = simple_config_lookup(fe, t_params, &frequency, &config, &cb);
if (ret < 0)
return 0; /* failure */
div = ((frequency + t_params->iffreq) * 62500 + offset +
tun->stepsize/2) / tun->stepsize;
buf[0] = div >> 8;
buf[1] = div & 0xff;
buf[2] = config;
buf[3] = cb;
simple_set_dvb(fe, buf, delsys, freq, bw);
tuner_dbg("%s: div=%d | buf=0x%02x,0x%02x,0x%02x,0x%02x\n",
tun->name, div, buf[0], buf[1], buf[2], buf[3]);
/* calculate the frequency we set it to */
return (div * tun->stepsize) - t_params->iffreq;
}
static int simple_dvb_calc_regs(struct dvb_frontend *fe,
u8 *buf, int buf_len)
{
struct dtv_frontend_properties *c = &fe->dtv_property_cache;
u32 delsys = c->delivery_system;
u32 bw = c->bandwidth_hz;
struct tuner_simple_priv *priv = fe->tuner_priv;
u32 frequency;
if (buf_len < 5)
return -EINVAL;
frequency = simple_dvb_configure(fe, buf+1, delsys, c->frequency, bw);
if (frequency == 0)
return -EINVAL;
buf[0] = priv->i2c_props.addr;
priv->frequency = frequency;
priv->bandwidth = c->bandwidth_hz;
return 5;
}
static int simple_dvb_set_params(struct dvb_frontend *fe)
{
struct dtv_frontend_properties *c = &fe->dtv_property_cache;
u32 delsys = c->delivery_system;
u32 bw = c->bandwidth_hz;
u32 freq = c->frequency;
struct tuner_simple_priv *priv = fe->tuner_priv;
u32 frequency;
u32 prev_freq, prev_bw;
int ret;
u8 buf[5];
if (priv->i2c_props.adap == NULL)
return -EINVAL;
prev_freq = priv->frequency;
prev_bw = priv->bandwidth;
frequency = simple_dvb_configure(fe, buf+1, delsys, freq, bw);
if (frequency == 0)
return -EINVAL;
buf[0] = priv->i2c_props.addr;
priv->frequency = frequency;
priv->bandwidth = bw;
/* put analog demod in standby when tuning digital */
if (fe->ops.analog_ops.standby)
fe->ops.analog_ops.standby(fe);
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
/* buf[0] contains the i2c address, but *
* we already have it in i2c_props.addr */
ret = tuner_i2c_xfer_send(&priv->i2c_props, buf+1, 4);
if (ret != 4)
goto fail;
return 0;
fail:
/* calc_regs sets frequency and bandwidth. if we failed, unset them */
priv->frequency = prev_freq;
priv->bandwidth = prev_bw;
return ret;
}
static int simple_init(struct dvb_frontend *fe)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
if (priv->i2c_props.adap == NULL)
return -EINVAL;
if (priv->tun->initdata) {
int ret;
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
ret = tuner_i2c_xfer_send(&priv->i2c_props,
priv->tun->initdata + 1,
priv->tun->initdata[0]);
if (ret != priv->tun->initdata[0])
return ret;
}
return 0;
}
static int simple_sleep(struct dvb_frontend *fe)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
if (priv->i2c_props.adap == NULL)
return -EINVAL;
if (priv->tun->sleepdata) {
int ret;
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
ret = tuner_i2c_xfer_send(&priv->i2c_props,
priv->tun->sleepdata + 1,
priv->tun->sleepdata[0]);
if (ret != priv->tun->sleepdata[0])
return ret;
}
return 0;
}
static void simple_release(struct dvb_frontend *fe)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
mutex_lock(&tuner_simple_list_mutex);
if (priv)
hybrid_tuner_release_state(priv);
mutex_unlock(&tuner_simple_list_mutex);
fe->tuner_priv = NULL;
}
static int simple_get_frequency(struct dvb_frontend *fe, u32 *frequency)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
*frequency = priv->frequency;
return 0;
}
static int simple_get_bandwidth(struct dvb_frontend *fe, u32 *bandwidth)
{
struct tuner_simple_priv *priv = fe->tuner_priv;
*bandwidth = priv->bandwidth;
return 0;
}
static const struct dvb_tuner_ops simple_tuner_ops = {
.init = simple_init,
.sleep = simple_sleep,
.set_analog_params = simple_set_params,
.set_params = simple_dvb_set_params,
.calc_regs = simple_dvb_calc_regs,
.release = simple_release,
.get_frequency = simple_get_frequency,
.get_bandwidth = simple_get_bandwidth,
.get_status = simple_get_status,
.get_rf_strength = simple_get_rf_strength,
};
struct dvb_frontend *simple_tuner_attach(struct dvb_frontend *fe,
struct i2c_adapter *i2c_adap,
u8 i2c_addr,
unsigned int type)
{
struct tuner_simple_priv *priv = NULL;
int instance;
if (type >= tuner_count) {
printk(KERN_WARNING "%s: invalid tuner type: %d (max: %d)\n",
__func__, type, tuner_count-1);
return NULL;
}
/* If i2c_adap is set, check that the tuner is at the correct address.
* Otherwise, if i2c_adap is NULL, the tuner will be programmed directly
* by the digital demod via calc_regs.
*/
if (i2c_adap != NULL) {
u8 b[1];
struct i2c_msg msg = {
.addr = i2c_addr, .flags = I2C_M_RD,
.buf = b, .len = 1,
};
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
if (1 != i2c_transfer(i2c_adap, &msg, 1))
printk(KERN_WARNING "tuner-simple %d-%04x: unable to probe %s, proceeding anyway.",
i2c_adapter_id(i2c_adap), i2c_addr,
tuners[type].name);
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 0);
}
mutex_lock(&tuner_simple_list_mutex);
instance = hybrid_tuner_request_state(struct tuner_simple_priv, priv,
hybrid_tuner_instance_list,
i2c_adap, i2c_addr,
"tuner-simple");
switch (instance) {
case 0:
mutex_unlock(&tuner_simple_list_mutex);
return NULL;
case 1:
fe->tuner_priv = priv;
priv->type = type;
priv->tun = &tuners[type];
priv->nr = simple_devcount++;
break;
default:
fe->tuner_priv = priv;
break;
}
mutex_unlock(&tuner_simple_list_mutex);
memcpy(&fe->ops.tuner_ops, &simple_tuner_ops,
sizeof(struct dvb_tuner_ops));
if (type != priv->type)
tuner_warn("couldn't set type to %d. Using %d (%s) instead\n",
type, priv->type, priv->tun->name);
else
tuner_info("type set to %d (%s)\n",
priv->type, priv->tun->name);
if ((debug) || ((atv_input[priv->nr] > 0) ||
(dtv_input[priv->nr] > 0))) {
if (0 == atv_input[priv->nr])
tuner_info("tuner %d atv rf input will be autoselected\n",
priv->nr);
else
tuner_info("tuner %d atv rf input will be set to input %d (insmod option)\n",
priv->nr, atv_input[priv->nr]);
if (0 == dtv_input[priv->nr])
tuner_info("tuner %d dtv rf input will be autoselected\n",
priv->nr);
else
tuner_info("tuner %d dtv rf input will be set to input %d (insmod option)\n",
priv->nr, dtv_input[priv->nr]);
}
strscpy(fe->ops.tuner_ops.info.name, priv->tun->name,
sizeof(fe->ops.tuner_ops.info.name));
return fe;
}
EXPORT_SYMBOL_GPL(simple_tuner_attach);
MODULE_DESCRIPTION("Simple 4-control-bytes style tuner driver");
MODULE_AUTHOR("Ralph Metzler, Gerd Knorr, Gunther Mayer");
MODULE_LICENSE("GPL");