OpenCloudOS-Kernel/drivers/spi/spi-dw.h

303 lines
7.7 KiB
C
Raw Normal View History

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
/* SPDX-License-Identifier: GPL-2.0 */
#ifndef DW_SPI_HEADER_H
#define DW_SPI_HEADER_H
#include <linux/bits.h>
spi: dw: Locally wait for the DMA transfers completion In general each DMA-based SPI transfer can be split up into two stages: DMA data transmission/reception and SPI-bus transmission/reception. DMA asynchronous transactions completion can be tracked by means of the DMA async Tx-descriptor completion callback. But that callback being called indicates that the DMA transfer has been finished, it doesn't mean that SPI data transmission is also done. Moreover in fact it isn't for at least Tx-only SPI transfers. Upon DMA transfer completion some data is left in the Tx FIFO and being pushed out by the SPI controller. So in order to make sure that an SPI transfer is completely pushed to the SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus transmission/reception are finished. Note if there is a way to asynchronously track the former event by means of the DMA async Tx callback, there isn't easy one for the later (IRQ-based solution won't work since SPI controller doesn't notify about Rx FIFO being empty). The DMA transfer completion callback isn't suitable to wait for the SPI controller activity finish either. The callback might (in case of DW DMAC it will) be called in the tasklet context. Waiting for the SPI controller to complete the transfer might take a considerable amount of time since SPI-bus might be pretty slow. In this case delaying the execution in the tasklet atomic context might cause significant system performance drop. So to speak the best option we've got to solve the problem is to consequently wait for both stages being finished in the locally implemented SPI transfer execution procedure even if it costs us of the local wait-function re-implementation. In this case we don't need to use the SPI-core transfer-wait functionality, but we'll make sure that all DMA and SPI-bus transactions are completely finished before the SPI-core transfer_one callback returns. In this commit we provide an implementation of the DMA-transfers completion wait functionality. The DW APB SSI DMA-specific SPI transfer_one function waits for both Tx and Rx DMA transfers being finished, and only then exits with zero returned signalling to the SPI core that the SPI transfer is finished. This implementation is fully equivalent to the currently used DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception wait methods will be added in the follow-up commits. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-29 21:11:52 +08:00
#include <linux/completion.h>
#include <linux/debugfs.h>
#include <linux/irqreturn.h>
#include <linux/io.h>
#include <linux/scatterlist.h>
spi: dw: Add memory operations support Aside from the synchronous Tx-Rx mode, which has been utilized to create the normal SPI transfers in the framework of the DW SSI driver, DW SPI controller supports Tx-only and EEPROM-read modes. The former one just enables the controller to transmit all the data from the Tx FIFO ignoring anything retrieved from the MISO lane. The later mode is so called write-then-read operation: DW SPI controller first pushes out all the data from the Tx FIFO, after that it'll automatically receive as much data as has been specified by means of the CTRLR1 register. Both of those modes can be used to implement the memory operations supported by the SPI-memory subsystem. The memory operation implementation is pretty much straightforward, except a few peculiarities we have had to take into account to make things working. Since DW SPI controller doesn't provide a way to directly set and clear the native CS lane level, but instead automatically de-asserts it when a transfer going on, we have to make sure the Tx FIFO isn't empty during entire Tx procedure. In addition we also need to read data from the Rx FIFO as fast as possible to prevent it' overflow with automatically fetched incoming traffic. The denoted peculiarities get to cause even more problems if DW SSI controller is equipped with relatively small FIFO and is connected to a relatively slow system bus (APB) (with respect to the SPI bus speed). In order to workaround the problems for as much as it's possible, the memory operation execution procedure collects all the Tx data into a single buffer and disables the local IRQs to speed the write-then-optionally-read method up. Note the provided memory operations are utilized by default only if a glue driver hasn't provided a custom version of ones and this is not a DW APB SSI controller with fixed automatic CS toggle functionality. Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-10-08 07:55:06 +08:00
#include <linux/spi/spi-mem.h>
spi: dw: Add support for 32-bits max xfer size The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward define a 32-bits maximum transfer size synthesis parameter (SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration (SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32, the layout of the ctrlr0 register changes, moving the data frame format field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size can be up to 32-bits. To support this new format, introduce the DW SPI capability flag DW_SPI_CAP_DFS32 to indicate that a controller is configured with SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis parameter not accessible through a register, the detection of this parameter value is done in spi_hw_init() by writing and reading the ctrlr0 register and testing the value of bits [3..0]. These bits are ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection. If a DFS32 capable SPI controller is detected, the new field dfs_offset in struct dw_spi is set to SPI_DFS32_OFFSET (16). dw_spi_update_config() is modified to set the data frame size field at the correct position is the CTRLR0 register, as indicated by the dfs_offset field of the dw_spi structure. The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI capability flag set. However, for these ssi controllers, the dfs_offset field is set to 0 as before (as per specifications). Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag set, dw_spi_add_host() extends the value of bits_per_word_mask from 16-bits to 32-bits. dw_reader() and dw_writer() are also modified to handle 32-bits iTX/RX FIFO words. Suggested-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Acked-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-12-06 09:18:16 +08:00
#include <linux/bitfield.h>
/* Register offsets */
#define DW_SPI_CTRLR0 0x00
#define DW_SPI_CTRLR1 0x04
#define DW_SPI_SSIENR 0x08
#define DW_SPI_MWCR 0x0c
#define DW_SPI_SER 0x10
#define DW_SPI_BAUDR 0x14
#define DW_SPI_TXFTLR 0x18
#define DW_SPI_RXFTLR 0x1c
#define DW_SPI_TXFLR 0x20
#define DW_SPI_RXFLR 0x24
#define DW_SPI_SR 0x28
#define DW_SPI_IMR 0x2c
#define DW_SPI_ISR 0x30
#define DW_SPI_RISR 0x34
#define DW_SPI_TXOICR 0x38
#define DW_SPI_RXOICR 0x3c
#define DW_SPI_RXUICR 0x40
#define DW_SPI_MSTICR 0x44
#define DW_SPI_ICR 0x48
#define DW_SPI_DMACR 0x4c
#define DW_SPI_DMATDLR 0x50
#define DW_SPI_DMARDLR 0x54
#define DW_SPI_IDR 0x58
#define DW_SPI_VERSION 0x5c
#define DW_SPI_DR 0x60
#define DW_SPI_RX_SAMPLE_DLY 0xf0
#define DW_SPI_CS_OVERRIDE 0xf4
/* Bit fields in CTRLR0 */
#define SPI_DFS_OFFSET 0
spi: dw: Add support for 32-bits max xfer size The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward define a 32-bits maximum transfer size synthesis parameter (SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration (SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32, the layout of the ctrlr0 register changes, moving the data frame format field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size can be up to 32-bits. To support this new format, introduce the DW SPI capability flag DW_SPI_CAP_DFS32 to indicate that a controller is configured with SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis parameter not accessible through a register, the detection of this parameter value is done in spi_hw_init() by writing and reading the ctrlr0 register and testing the value of bits [3..0]. These bits are ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection. If a DFS32 capable SPI controller is detected, the new field dfs_offset in struct dw_spi is set to SPI_DFS32_OFFSET (16). dw_spi_update_config() is modified to set the data frame size field at the correct position is the CTRLR0 register, as indicated by the dfs_offset field of the dw_spi structure. The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI capability flag set. However, for these ssi controllers, the dfs_offset field is set to 0 as before (as per specifications). Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag set, dw_spi_add_host() extends the value of bits_per_word_mask from 16-bits to 32-bits. dw_reader() and dw_writer() are also modified to handle 32-bits iTX/RX FIFO words. Suggested-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Acked-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-12-06 09:18:16 +08:00
#define SPI_DFS_MASK GENMASK(3, 0)
#define SPI_DFS32_OFFSET 16
#define SPI_FRF_OFFSET 4
#define SPI_FRF_SPI 0x0
#define SPI_FRF_SSP 0x1
#define SPI_FRF_MICROWIRE 0x2
#define SPI_FRF_RESV 0x3
#define SPI_MODE_OFFSET 6
#define SPI_SCPH_OFFSET 6
#define SPI_SCOL_OFFSET 7
#define SPI_TMOD_OFFSET 8
#define SPI_TMOD_MASK (0x3 << SPI_TMOD_OFFSET)
#define SPI_TMOD_TR 0x0 /* xmit & recv */
#define SPI_TMOD_TO 0x1 /* xmit only */
#define SPI_TMOD_RO 0x2 /* recv only */
#define SPI_TMOD_EPROMREAD 0x3 /* eeprom read mode */
#define SPI_SLVOE_OFFSET 10
#define SPI_SRL_OFFSET 11
#define SPI_CFS_OFFSET 12
spi: dw: Add support for DesignWare DWC_ssi This patch adds initial support for DesignWare DWC_ssi soft IP. DWC_ssi is the enhanced version of DW_apb_ssi, which is currently supported by this driver. Their registers are same, but the bit fields of register CTRLR0 are different. DWC_ssi has additional features compared to DW_apb_ssi. Major enhancements in DWC_ssi are hyper bus protocol, boot mode support and advanced XIP support. DWC_ssi is an AHB slave device, whilst DW_apb_ssi is an APB slave device. Register offset DW_ssi DW_apb_ssi CTRLR0 0x00 0x00 CTRLR1 0x04 0x04 SSIENR 0x08 0x08 MWCR 0x0c 0x0c SER 0x10 0x10 BAUDR 0x14 0x14 TXFTLR 0x18 0x18 RXFTLR 0x1c 0x1c TXFLR 0x20 0x20 RXFLR 0x24 0x24 SR 0x28 0x28 IMR 0x2c 0x2c ISR 0x30 0x30 RISR 0x34 0x34 TXOICR 0x38 0x38 RXOICR 0x3c 0x3c RXUICR 0x40 0x40 MSTICR 0x44 0x44 ICR 0x48 0x48 DMACR 0x4c 0x4c DMATDLR 0x50 0x50 DMARDLR 0x54 0x54 IDR 0x58 0x58 SSI_VERSION_ID 0x5c 0x5c DRx (0 to 35) 0x60+i*0x4 0x60+i*0x4 RX_SAMPLE_DLY 0xf0 0xf0 SPI_CTRLR0 0xf4 0xf4 TXD_DRIVE_EDGE 0xf8 0xf8 XIP_MODE_BITS 0xfc RSVD Register configuration - CTRLR0 DW_ssi DW_apb_ssi SPI_HYPERBUS_EN bit[24] NONE SPI_FRF bit[23:22] bit[22:21] DFS_32 NONE bit[20:16] CFS bit[19:16] bit[15:12] SSTE bit[14] bit[24] SRL bit[13] bit[11] SLV_OE bit[12] bit[10] TMOD bit[11:10] bit[9:8] SCPOL | SPHA bit[9:8] bit[7:6] FRF bit[7:6] bit[5:4] DFS bit[4:0] bit[3:0] The documents used are [1] DW_apb_ssi_databook.pdf version 4.01a (2016.10a). [2] DWC_ssi_databook.pdf version 1.01a. Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200505130618.554-4-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05 21:06:14 +08:00
/* Bit fields in CTRLR0 based on DWC_ssi_databook.pdf v1.01a */
#define DWC_SSI_CTRLR0_SRL_OFFSET 13
#define DWC_SSI_CTRLR0_TMOD_OFFSET 10
#define DWC_SSI_CTRLR0_TMOD_MASK GENMASK(11, 10)
#define DWC_SSI_CTRLR0_SCPOL_OFFSET 9
#define DWC_SSI_CTRLR0_SCPH_OFFSET 8
#define DWC_SSI_CTRLR0_FRF_OFFSET 6
#define DWC_SSI_CTRLR0_DFS_OFFSET 0
/*
* For Keem Bay, CTRLR0[31] is used to select controller mode.
* 0: SSI is slave
* 1: SSI is master
*/
#define DWC_SSI_CTRLR0_KEEMBAY_MST BIT(31)
spi: dw: Add memory operations support Aside from the synchronous Tx-Rx mode, which has been utilized to create the normal SPI transfers in the framework of the DW SSI driver, DW SPI controller supports Tx-only and EEPROM-read modes. The former one just enables the controller to transmit all the data from the Tx FIFO ignoring anything retrieved from the MISO lane. The later mode is so called write-then-read operation: DW SPI controller first pushes out all the data from the Tx FIFO, after that it'll automatically receive as much data as has been specified by means of the CTRLR1 register. Both of those modes can be used to implement the memory operations supported by the SPI-memory subsystem. The memory operation implementation is pretty much straightforward, except a few peculiarities we have had to take into account to make things working. Since DW SPI controller doesn't provide a way to directly set and clear the native CS lane level, but instead automatically de-asserts it when a transfer going on, we have to make sure the Tx FIFO isn't empty during entire Tx procedure. In addition we also need to read data from the Rx FIFO as fast as possible to prevent it' overflow with automatically fetched incoming traffic. The denoted peculiarities get to cause even more problems if DW SSI controller is equipped with relatively small FIFO and is connected to a relatively slow system bus (APB) (with respect to the SPI bus speed). In order to workaround the problems for as much as it's possible, the memory operation execution procedure collects all the Tx data into a single buffer and disables the local IRQs to speed the write-then-optionally-read method up. Note the provided memory operations are utilized by default only if a glue driver hasn't provided a custom version of ones and this is not a DW APB SSI controller with fixed automatic CS toggle functionality. Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-10-08 07:55:06 +08:00
/* Bit fields in CTRLR1 */
#define SPI_NDF_MASK GENMASK(15, 0)
/* Bit fields in SR, 7 bits */
#define SR_MASK 0x7f /* cover 7 bits */
#define SR_BUSY (1 << 0)
#define SR_TF_NOT_FULL (1 << 1)
#define SR_TF_EMPT (1 << 2)
#define SR_RF_NOT_EMPT (1 << 3)
#define SR_RF_FULL (1 << 4)
#define SR_TX_ERR (1 << 5)
#define SR_DCOL (1 << 6)
/* Bit fields in ISR, IMR, RISR, 7 bits */
#define SPI_INT_TXEI (1 << 0)
#define SPI_INT_TXOI (1 << 1)
#define SPI_INT_RXUI (1 << 2)
#define SPI_INT_RXOI (1 << 3)
#define SPI_INT_RXFI (1 << 4)
#define SPI_INT_MSTI (1 << 5)
/* Bit fields in DMACR */
#define SPI_DMA_RDMAE (1 << 0)
#define SPI_DMA_TDMAE (1 << 1)
#define SPI_WAIT_RETRIES 5
spi: dw: Add memory operations support Aside from the synchronous Tx-Rx mode, which has been utilized to create the normal SPI transfers in the framework of the DW SSI driver, DW SPI controller supports Tx-only and EEPROM-read modes. The former one just enables the controller to transmit all the data from the Tx FIFO ignoring anything retrieved from the MISO lane. The later mode is so called write-then-read operation: DW SPI controller first pushes out all the data from the Tx FIFO, after that it'll automatically receive as much data as has been specified by means of the CTRLR1 register. Both of those modes can be used to implement the memory operations supported by the SPI-memory subsystem. The memory operation implementation is pretty much straightforward, except a few peculiarities we have had to take into account to make things working. Since DW SPI controller doesn't provide a way to directly set and clear the native CS lane level, but instead automatically de-asserts it when a transfer going on, we have to make sure the Tx FIFO isn't empty during entire Tx procedure. In addition we also need to read data from the Rx FIFO as fast as possible to prevent it' overflow with automatically fetched incoming traffic. The denoted peculiarities get to cause even more problems if DW SSI controller is equipped with relatively small FIFO and is connected to a relatively slow system bus (APB) (with respect to the SPI bus speed). In order to workaround the problems for as much as it's possible, the memory operation execution procedure collects all the Tx data into a single buffer and disables the local IRQs to speed the write-then-optionally-read method up. Note the provided memory operations are utilized by default only if a glue driver hasn't provided a custom version of ones and this is not a DW APB SSI controller with fixed automatic CS toggle functionality. Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-10-08 07:55:06 +08:00
#define SPI_BUF_SIZE \
(sizeof_field(struct spi_mem_op, cmd.opcode) + \
sizeof_field(struct spi_mem_op, addr.val) + 256)
#define SPI_GET_BYTE(_val, _idx) \
((_val) >> (BITS_PER_BYTE * (_idx)) & 0xff)
enum dw_ssi_type {
SSI_MOTO_SPI = 0,
SSI_TI_SSP,
SSI_NS_MICROWIRE,
};
/* DW SPI capabilities */
#define DW_SPI_CAP_CS_OVERRIDE BIT(0)
#define DW_SPI_CAP_KEEMBAY_MST BIT(1)
2020-10-08 07:54:51 +08:00
#define DW_SPI_CAP_DWC_SSI BIT(2)
spi: dw: Add support for 32-bits max xfer size The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward define a 32-bits maximum transfer size synthesis parameter (SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration (SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32, the layout of the ctrlr0 register changes, moving the data frame format field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size can be up to 32-bits. To support this new format, introduce the DW SPI capability flag DW_SPI_CAP_DFS32 to indicate that a controller is configured with SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis parameter not accessible through a register, the detection of this parameter value is done in spi_hw_init() by writing and reading the ctrlr0 register and testing the value of bits [3..0]. These bits are ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection. If a DFS32 capable SPI controller is detected, the new field dfs_offset in struct dw_spi is set to SPI_DFS32_OFFSET (16). dw_spi_update_config() is modified to set the data frame size field at the correct position is the CTRLR0 register, as indicated by the dfs_offset field of the dw_spi structure. The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI capability flag set. However, for these ssi controllers, the dfs_offset field is set to 0 as before (as per specifications). Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag set, dw_spi_add_host() extends the value of bits_per_word_mask from 16-bits to 32-bits. dw_reader() and dw_writer() are also modified to handle 32-bits iTX/RX FIFO words. Suggested-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Acked-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-12-06 09:18:16 +08:00
#define DW_SPI_CAP_DFS32 BIT(3)
/* Slave spi_transfer/spi_mem_op related */
struct dw_spi_cfg {
u8 tmode;
u8 dfs;
u32 ndf;
u32 freq;
};
struct dw_spi;
struct dw_spi_dma_ops {
int (*dma_init)(struct device *dev, struct dw_spi *dws);
void (*dma_exit)(struct dw_spi *dws);
int (*dma_setup)(struct dw_spi *dws, struct spi_transfer *xfer);
bool (*can_dma)(struct spi_controller *master, struct spi_device *spi,
struct spi_transfer *xfer);
int (*dma_transfer)(struct dw_spi *dws, struct spi_transfer *xfer);
void (*dma_stop)(struct dw_spi *dws);
};
struct dw_spi {
struct spi_controller *master;
void __iomem *regs;
unsigned long paddr;
int irq;
u32 fifo_len; /* depth of the FIFO buffer */
spi: dw: Add support for 32-bits max xfer size The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward define a 32-bits maximum transfer size synthesis parameter (SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration (SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32, the layout of the ctrlr0 register changes, moving the data frame format field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size can be up to 32-bits. To support this new format, introduce the DW SPI capability flag DW_SPI_CAP_DFS32 to indicate that a controller is configured with SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis parameter not accessible through a register, the detection of this parameter value is done in spi_hw_init() by writing and reading the ctrlr0 register and testing the value of bits [3..0]. These bits are ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection. If a DFS32 capable SPI controller is detected, the new field dfs_offset in struct dw_spi is set to SPI_DFS32_OFFSET (16). dw_spi_update_config() is modified to set the data frame size field at the correct position is the CTRLR0 register, as indicated by the dfs_offset field of the dw_spi structure. The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI capability flag set. However, for these ssi controllers, the dfs_offset field is set to 0 as before (as per specifications). Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag set, dw_spi_add_host() extends the value of bits_per_word_mask from 16-bits to 32-bits. dw_reader() and dw_writer() are also modified to handle 32-bits iTX/RX FIFO words. Suggested-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Acked-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-12-06 09:18:16 +08:00
unsigned int dfs_offset; /* CTRLR0 DFS field offset */
u32 max_mem_freq; /* max mem-ops bus freq */
u32 max_freq; /* max bus freq supported */
u32 caps; /* DW SPI capabilities */
u32 reg_io_width; /* DR I/O width in bytes */
u16 bus_num;
u16 num_cs; /* supported slave numbers */
void (*set_cs)(struct spi_device *spi, bool enable);
/* Current message transfer state info */
void *tx;
unsigned int tx_len;
void *rx;
unsigned int rx_len;
spi: dw: Add memory operations support Aside from the synchronous Tx-Rx mode, which has been utilized to create the normal SPI transfers in the framework of the DW SSI driver, DW SPI controller supports Tx-only and EEPROM-read modes. The former one just enables the controller to transmit all the data from the Tx FIFO ignoring anything retrieved from the MISO lane. The later mode is so called write-then-read operation: DW SPI controller first pushes out all the data from the Tx FIFO, after that it'll automatically receive as much data as has been specified by means of the CTRLR1 register. Both of those modes can be used to implement the memory operations supported by the SPI-memory subsystem. The memory operation implementation is pretty much straightforward, except a few peculiarities we have had to take into account to make things working. Since DW SPI controller doesn't provide a way to directly set and clear the native CS lane level, but instead automatically de-asserts it when a transfer going on, we have to make sure the Tx FIFO isn't empty during entire Tx procedure. In addition we also need to read data from the Rx FIFO as fast as possible to prevent it' overflow with automatically fetched incoming traffic. The denoted peculiarities get to cause even more problems if DW SSI controller is equipped with relatively small FIFO and is connected to a relatively slow system bus (APB) (with respect to the SPI bus speed). In order to workaround the problems for as much as it's possible, the memory operation execution procedure collects all the Tx data into a single buffer and disables the local IRQs to speed the write-then-optionally-read method up. Note the provided memory operations are utilized by default only if a glue driver hasn't provided a custom version of ones and this is not a DW APB SSI controller with fixed automatic CS toggle functionality. Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-10-08 07:55:06 +08:00
u8 buf[SPI_BUF_SIZE];
int dma_mapped;
u8 n_bytes; /* current is a 1/2 bytes op */
irqreturn_t (*transfer_handler)(struct dw_spi *dws);
u32 current_freq; /* frequency in hz */
u32 cur_rx_sample_dly;
u32 def_rx_sample_dly_ns;
spi: dw: Add memory operations support Aside from the synchronous Tx-Rx mode, which has been utilized to create the normal SPI transfers in the framework of the DW SSI driver, DW SPI controller supports Tx-only and EEPROM-read modes. The former one just enables the controller to transmit all the data from the Tx FIFO ignoring anything retrieved from the MISO lane. The later mode is so called write-then-read operation: DW SPI controller first pushes out all the data from the Tx FIFO, after that it'll automatically receive as much data as has been specified by means of the CTRLR1 register. Both of those modes can be used to implement the memory operations supported by the SPI-memory subsystem. The memory operation implementation is pretty much straightforward, except a few peculiarities we have had to take into account to make things working. Since DW SPI controller doesn't provide a way to directly set and clear the native CS lane level, but instead automatically de-asserts it when a transfer going on, we have to make sure the Tx FIFO isn't empty during entire Tx procedure. In addition we also need to read data from the Rx FIFO as fast as possible to prevent it' overflow with automatically fetched incoming traffic. The denoted peculiarities get to cause even more problems if DW SSI controller is equipped with relatively small FIFO and is connected to a relatively slow system bus (APB) (with respect to the SPI bus speed). In order to workaround the problems for as much as it's possible, the memory operation execution procedure collects all the Tx data into a single buffer and disables the local IRQs to speed the write-then-optionally-read method up. Note the provided memory operations are utilized by default only if a glue driver hasn't provided a custom version of ones and this is not a DW APB SSI controller with fixed automatic CS toggle functionality. Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-10-08 07:55:06 +08:00
/* Custom memory operations */
struct spi_controller_mem_ops mem_ops;
/* DMA info */
struct dma_chan *txchan;
u32 txburst;
struct dma_chan *rxchan;
u32 rxburst;
spi: dw-dma: Add one-by-one SG list entries transfer In case if at least one of the requested DMA engine channels doesn't support the hardware accelerated SG list entries traverse, the DMA driver will most likely work that around by performing the IRQ-based SG list entries resubmission. That might and will cause a problem if the DMA Tx channel is recharged and re-executed before the Rx DMA channel. Due to non-deterministic IRQ-handler execution latency the DMA Tx channel will start pushing data to the SPI bus before the Rx DMA channel is even reinitialized with the next inbound SG list entry. By doing so the DMA Tx channel will implicitly start filling the DW APB SSI Rx FIFO up, which while the DMA Rx channel being recharged and re-executed will eventually be overflown. In order to solve the problem we have to feed the DMA engine with SG list entries one-by-one. It shall keep the DW APB SSI Tx and Rx FIFOs synchronized and prevent the Rx FIFO overflow. Since in general the SPI tx_sg and rx_sg lists may have different number of entries of different lengths (though total length should match) we virtually split the SG-lists to the set of DMA transfers, which length is a minimum of the ordered SG-entries lengths. The solution described above is only executed if a full-duplex SPI transfer is requested and the DMA engine hasn't provided channels with hardware accelerated SG list traverse capability to handle both SG lists at once. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200920112322.24585-12-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-09-20 19:23:22 +08:00
u32 dma_sg_burst;
unsigned long dma_chan_busy;
dma_addr_t dma_addr; /* phy address of the Data register */
const struct dw_spi_dma_ops *dma_ops;
spi: dw: Locally wait for the DMA transfers completion In general each DMA-based SPI transfer can be split up into two stages: DMA data transmission/reception and SPI-bus transmission/reception. DMA asynchronous transactions completion can be tracked by means of the DMA async Tx-descriptor completion callback. But that callback being called indicates that the DMA transfer has been finished, it doesn't mean that SPI data transmission is also done. Moreover in fact it isn't for at least Tx-only SPI transfers. Upon DMA transfer completion some data is left in the Tx FIFO and being pushed out by the SPI controller. So in order to make sure that an SPI transfer is completely pushed to the SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus transmission/reception are finished. Note if there is a way to asynchronously track the former event by means of the DMA async Tx callback, there isn't easy one for the later (IRQ-based solution won't work since SPI controller doesn't notify about Rx FIFO being empty). The DMA transfer completion callback isn't suitable to wait for the SPI controller activity finish either. The callback might (in case of DW DMAC it will) be called in the tasklet context. Waiting for the SPI controller to complete the transfer might take a considerable amount of time since SPI-bus might be pretty slow. In this case delaying the execution in the tasklet atomic context might cause significant system performance drop. So to speak the best option we've got to solve the problem is to consequently wait for both stages being finished in the locally implemented SPI transfer execution procedure even if it costs us of the local wait-function re-implementation. In this case we don't need to use the SPI-core transfer-wait functionality, but we'll make sure that all DMA and SPI-bus transactions are completely finished before the SPI-core transfer_one callback returns. In this commit we provide an implementation of the DMA-transfers completion wait functionality. The DW APB SSI DMA-specific SPI transfer_one function waits for both Tx and Rx DMA transfers being finished, and only then exits with zero returned signalling to the SPI core that the SPI transfer is finished. This implementation is fully equivalent to the currently used DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception wait methods will be added in the follow-up commits. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-29 21:11:52 +08:00
struct completion dma_completion;
#ifdef CONFIG_DEBUG_FS
struct dentry *debugfs;
struct debugfs_regset32 regset;
#endif
};
static inline u32 dw_readl(struct dw_spi *dws, u32 offset)
{
return __raw_readl(dws->regs + offset);
}
static inline void dw_writel(struct dw_spi *dws, u32 offset, u32 val)
{
__raw_writel(val, dws->regs + offset);
}
static inline u32 dw_read_io_reg(struct dw_spi *dws, u32 offset)
{
switch (dws->reg_io_width) {
case 2:
return readw_relaxed(dws->regs + offset);
case 4:
default:
return readl_relaxed(dws->regs + offset);
}
}
static inline void dw_write_io_reg(struct dw_spi *dws, u32 offset, u32 val)
{
switch (dws->reg_io_width) {
case 2:
writew_relaxed(val, dws->regs + offset);
break;
case 4:
default:
writel_relaxed(val, dws->regs + offset);
break;
}
}
static inline void spi_enable_chip(struct dw_spi *dws, int enable)
{
dw_writel(dws, DW_SPI_SSIENR, (enable ? 1 : 0));
}
static inline void spi_set_clk(struct dw_spi *dws, u16 div)
{
dw_writel(dws, DW_SPI_BAUDR, div);
}
/* Disable IRQ bits */
static inline void spi_mask_intr(struct dw_spi *dws, u32 mask)
{
u32 new_mask;
new_mask = dw_readl(dws, DW_SPI_IMR) & ~mask;
dw_writel(dws, DW_SPI_IMR, new_mask);
}
/* Enable IRQ bits */
static inline void spi_umask_intr(struct dw_spi *dws, u32 mask)
{
u32 new_mask;
new_mask = dw_readl(dws, DW_SPI_IMR) | mask;
dw_writel(dws, DW_SPI_IMR, new_mask);
}
/*
* This disables the SPI controller, interrupts, clears the interrupts status
* and CS, then re-enables the controller back. Transmit and receive FIFO
* buffers are cleared when the device is disabled.
*/
static inline void spi_reset_chip(struct dw_spi *dws)
{
spi_enable_chip(dws, 0);
spi_mask_intr(dws, 0xff);
dw_readl(dws, DW_SPI_ICR);
dw_writel(dws, DW_SPI_SER, 0);
spi_enable_chip(dws, 1);
}
static inline void spi_shutdown_chip(struct dw_spi *dws)
{
spi_enable_chip(dws, 0);
spi_set_clk(dws, 0);
}
extern void dw_spi_set_cs(struct spi_device *spi, bool enable);
extern void dw_spi_update_config(struct dw_spi *dws, struct spi_device *spi,
struct dw_spi_cfg *cfg);
extern int dw_spi_check_status(struct dw_spi *dws, bool raw);
extern int dw_spi_add_host(struct device *dev, struct dw_spi *dws);
extern void dw_spi_remove_host(struct dw_spi *dws);
extern int dw_spi_suspend_host(struct dw_spi *dws);
extern int dw_spi_resume_host(struct dw_spi *dws);
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver This is a preparation patch before adding the DW DMA support into the DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the intended to be generic DW APB SSI DMA code. This isn't that hard, since the most part of the spi-dw-mid.c driver in fact implements a generic DMA interface for the DW SPI controller driver. The only Intel MID specifics concern getting the max frequency from the MRST Clock Control Unit and fetching the DMA controller channels from corresponding PCIe DMA controller. Since first one is related with the SPI interface configuration we moved it' implementation into the DW PCIe-SPI driver module. After that former spi-dw-mid.c file can be just renamed to be the DW SPI DMA module optionally compiled in to the DW APB SSI core driver. Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-29 21:11:59 +08:00
#ifdef CONFIG_SPI_DW_DMA
extern void dw_spi_dma_setup_mfld(struct dw_spi *dws);
extern void dw_spi_dma_setup_generic(struct dw_spi *dws);
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver This is a preparation patch before adding the DW DMA support into the DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the intended to be generic DW APB SSI DMA code. This isn't that hard, since the most part of the spi-dw-mid.c driver in fact implements a generic DMA interface for the DW SPI controller driver. The only Intel MID specifics concern getting the max frequency from the MRST Clock Control Unit and fetching the DMA controller channels from corresponding PCIe DMA controller. Since first one is related with the SPI interface configuration we moved it' implementation into the DW PCIe-SPI driver module. After that former spi-dw-mid.c file can be just renamed to be the DW SPI DMA module optionally compiled in to the DW APB SSI core driver. Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-29 21:11:59 +08:00
#else
static inline void dw_spi_dma_setup_mfld(struct dw_spi *dws) {}
static inline void dw_spi_dma_setup_generic(struct dw_spi *dws) {}
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver This is a preparation patch before adding the DW DMA support into the DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the intended to be generic DW APB SSI DMA code. This isn't that hard, since the most part of the spi-dw-mid.c driver in fact implements a generic DMA interface for the DW SPI controller driver. The only Intel MID specifics concern getting the max frequency from the MRST Clock Control Unit and fetching the DMA controller channels from corresponding PCIe DMA controller. Since first one is related with the SPI interface configuration we moved it' implementation into the DW PCIe-SPI driver module. After that former spi-dw-mid.c file can be just renamed to be the DW SPI DMA module optionally compiled in to the DW APB SSI core driver. Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-29 21:11:59 +08:00
#endif /* !CONFIG_SPI_DW_DMA */
#endif /* DW_SPI_HEADER_H */