OpenCloudOS-Kernel/arch/mips/kernel/smp-cps.c

655 lines
16 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2013 Imagination Technologies
Update MIPS email addresses MIPS will soon not be a part of Imagination Technologies, and as such many @imgtec.com email addresses will no longer be valid. This patch updates the addresses for those who: - Have 10 or more patches in mainline authored using an @imgtec.com email address, or any patches dated within the past year. - Are still with Imagination but leaving as part of the MIPS business unit, as determined from an internal email address list. - Haven't already updated their email address (ie. JamesH) or expressed a desire to be excluded (ie. Maciej). - Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt & myself. New addresses are of the form firstname.lastname@mips.com, and all verified against an internal email address list. An entry is added to .mailmap for each person such that get_maintainer.pl will report the new addresses rather than @imgtec.com addresses which will soon be dead. Instances of the affected addresses throughout the tree are then mechanically replaced with the new @mips.com address. Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com> Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com> Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Matt Redfearn <matt.redfearn@mips.com> Acked-by: Matt Redfearn <matt.redfearn@mips.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: trivial@kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17540/ Signed-off-by: James Hogan <jhogan@kernel.org>
2017-10-26 08:04:33 +08:00
* Author: Paul Burton <paul.burton@mips.com>
*/
#include <linux/cpu.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/sched/task_stack.h>
#include <linux/sched/hotplug.h>
#include <linux/slab.h>
#include <linux/smp.h>
#include <linux/types.h>
#include <linux/irq.h>
#include <asm/bcache.h>
#include <asm/mips-cps.h>
#include <asm/mips_mt.h>
#include <asm/mipsregs.h>
#include <asm/pm-cps.h>
#include <asm/r4kcache.h>
#include <asm/smp.h>
#include <asm/smp-cps.h>
#include <asm/time.h>
#include <asm/uasm.h>
static bool threads_disabled;
static DECLARE_BITMAP(core_power, NR_CPUS);
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
struct core_boot_config *mips_cps_core_bootcfg;
static int __init setup_nothreads(char *s)
{
threads_disabled = true;
return 0;
}
early_param("nothreads", setup_nothreads);
static unsigned core_vpe_count(unsigned int cluster, unsigned core)
{
if (threads_disabled)
return 1;
return mips_cps_numvps(cluster, core);
}
static void __init cps_smp_setup(void)
{
unsigned int nclusters, ncores, nvpes, core_vpes;
unsigned long core_entry;
int cl, c, v;
/* Detect & record VPE topology */
nvpes = 0;
nclusters = mips_cps_numclusters();
pr_info("%s topology ", cpu_has_mips_r6 ? "VP" : "VPE");
for (cl = 0; cl < nclusters; cl++) {
if (cl > 0)
pr_cont(",");
pr_cont("{");
ncores = mips_cps_numcores(cl);
for (c = 0; c < ncores; c++) {
core_vpes = core_vpe_count(cl, c);
if (c > 0)
pr_cont(",");
pr_cont("%u", core_vpes);
/* Use the number of VPEs in cluster 0 core 0 for smp_num_siblings */
if (!cl && !c)
smp_num_siblings = core_vpes;
for (v = 0; v < min_t(int, core_vpes, NR_CPUS - nvpes); v++) {
cpu_set_cluster(&cpu_data[nvpes + v], cl);
cpu_set_core(&cpu_data[nvpes + v], c);
cpu_set_vpe_id(&cpu_data[nvpes + v], v);
}
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
nvpes += core_vpes;
}
pr_cont("}");
}
pr_cont(" total %u\n", nvpes);
/* Indicate present CPUs (CPU being synonymous with VPE) */
for (v = 0; v < min_t(unsigned, nvpes, NR_CPUS); v++) {
set_cpu_possible(v, cpu_cluster(&cpu_data[v]) == 0);
set_cpu_present(v, cpu_cluster(&cpu_data[v]) == 0);
__cpu_number_map[v] = v;
__cpu_logical_map[v] = v;
}
/* Set a coherent default CCA (CWB) */
change_c0_config(CONF_CM_CMASK, 0x5);
/* Core 0 is powered up (we're running on it) */
bitmap_set(core_power, 0, 1);
/* Initialise core 0 */
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
mips_cps_core_init();
/* Make core 0 coherent with everything */
write_gcr_cl_coherence(0xff);
if (mips_cm_revision() >= CM_REV_CM3) {
core_entry = CKSEG1ADDR((unsigned long)mips_cps_core_entry);
write_gcr_bev_base(core_entry);
}
#ifdef CONFIG_MIPS_MT_FPAFF
/* If we have an FPU, enroll ourselves in the FPU-full mask */
if (cpu_has_fpu)
cpumask_set_cpu(0, &mt_fpu_cpumask);
#endif /* CONFIG_MIPS_MT_FPAFF */
}
static void __init cps_prepare_cpus(unsigned int max_cpus)
{
unsigned ncores, core_vpes, c, cca;
bool cca_unsuitable, cores_limited;
u32 *entry_code;
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
mips_mt_set_cpuoptions();
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
/* Detect whether the CCA is unsuited to multi-core SMP */
cca = read_c0_config() & CONF_CM_CMASK;
switch (cca) {
case 0x4: /* CWBE */
case 0x5: /* CWB */
/* The CCA is coherent, multi-core is fine */
cca_unsuitable = false;
break;
default:
/* CCA is not coherent, multi-core is not usable */
cca_unsuitable = true;
}
/* Warn the user if the CCA prevents multi-core */
cores_limited = false;
if (cca_unsuitable || cpu_has_dc_aliases) {
for_each_present_cpu(c) {
if (cpus_are_siblings(smp_processor_id(), c))
continue;
set_cpu_present(c, false);
cores_limited = true;
}
}
if (cores_limited)
pr_warn("Using only one core due to %s%s%s\n",
cca_unsuitable ? "unsuitable CCA" : "",
(cca_unsuitable && cpu_has_dc_aliases) ? " & " : "",
cpu_has_dc_aliases ? "dcache aliasing" : "");
/*
* Patch the start of mips_cps_core_entry to provide:
*
* s0 = kseg0 CCA
*/
entry_code = (u32 *)&mips_cps_core_entry;
uasm_i_addiu(&entry_code, 16, 0, cca);
UASM_i_LA(&entry_code, 17, (long)mips_gcr_base);
BUG_ON((void *)entry_code > (void *)&mips_cps_core_entry_patch_end);
blast_dcache_range((unsigned long)&mips_cps_core_entry,
(unsigned long)entry_code);
bc_wback_inv((unsigned long)&mips_cps_core_entry,
(void *)entry_code - (void *)&mips_cps_core_entry);
__sync();
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
/* Allocate core boot configuration structs */
ncores = mips_cps_numcores(0);
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
mips_cps_core_bootcfg = kcalloc(ncores, sizeof(*mips_cps_core_bootcfg),
GFP_KERNEL);
if (!mips_cps_core_bootcfg) {
pr_err("Failed to allocate boot config for %u cores\n", ncores);
goto err_out;
}
/* Allocate VPE boot configuration structs */
for (c = 0; c < ncores; c++) {
core_vpes = core_vpe_count(0, c);
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
mips_cps_core_bootcfg[c].vpe_config = kcalloc(core_vpes,
sizeof(*mips_cps_core_bootcfg[c].vpe_config),
GFP_KERNEL);
if (!mips_cps_core_bootcfg[c].vpe_config) {
pr_err("Failed to allocate %u VPE boot configs\n",
core_vpes);
goto err_out;
}
}
/* Mark this CPU as booted */
atomic_set(&mips_cps_core_bootcfg[cpu_core(&current_cpu_data)].vpe_mask,
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
1 << cpu_vpe_id(&current_cpu_data));
return;
err_out:
/* Clean up allocations */
if (mips_cps_core_bootcfg) {
for (c = 0; c < ncores; c++)
kfree(mips_cps_core_bootcfg[c].vpe_config);
kfree(mips_cps_core_bootcfg);
mips_cps_core_bootcfg = NULL;
}
/* Effectively disable SMP by declaring CPUs not present */
for_each_possible_cpu(c) {
if (c == 0)
continue;
set_cpu_present(c, false);
}
}
static void boot_core(unsigned int core, unsigned int vpe_id)
{
u32 stat, seq_state;
unsigned timeout;
/* Select the appropriate core */
mips_cm_lock_other(0, core, 0, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
/* Set its reset vector */
write_gcr_co_reset_base(CKSEG1ADDR((unsigned long)mips_cps_core_entry));
/* Ensure its coherency is disabled */
write_gcr_co_coherence(0);
/* Start it with the legacy memory map and exception base */
MIPS: CM: Use BIT/GENMASK for register fields, order & drop shifts There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h when declaring macros corresponding to register fields. This patch modifies our definitions to do so. The *_SHF definitions are removed entirely - they duplicate information found in the masks, are infrequently used & can be replaced with use of __ffs() where needed. The *_MSK definitions then lose their _MSK suffix which is now somewhat redundant, and users are modified to match. The field definitions are moved to follow the appropriate register's accessor functions, which helps to keep the field definitions in order & to find the appropriate fields for a given register. Whilst here a comment is added describing each register & including its name, which is helpful both for linking the register back to hardware documentation & for grepping purposes. This also cleans up a couple of issues that became obvious as a result of making the changes described above: - We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony copy of that named GCR_RESET_EXT_BASE - a register which does not exist. The bad definitions were added by commit 497e803ebf98 ("MIPS: smp-cps: Ensure secondary cores start with EVA disabled") and made use of from boot_core(), which is now modified to use the GCR_Cx_RESET_EXT_BASE definitions. - We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly define this as inFo rather than inGo. Now that we don't duplicate field information between _SHF & _MSK definitions, and keep the fields next to the register accessors, it will be much easier to spot & prevent any similar oddities being introduced in the future. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Thomas Gleixner <tglx@linutronix.de Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17001/ Patchwork: https://patchwork.linux-mips.org/patch/17216/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-13 10:49:27 +08:00
write_gcr_co_reset_ext_base(CM_GCR_Cx_RESET_EXT_BASE_UEB);
/* Ensure the core can access the GCRs */
set_gcr_access(1 << core);
if (mips_cpc_present()) {
/* Reset the core */
mips_cpc_lock_other(core);
if (mips_cm_revision() >= CM_REV_CM3) {
/* Run only the requested VP following the reset */
write_cpc_co_vp_stop(0xf);
write_cpc_co_vp_run(1 << vpe_id);
/*
* Ensure that the VP_RUN register is written before the
* core leaves reset.
*/
wmb();
}
write_cpc_co_cmd(CPC_Cx_CMD_RESET);
timeout = 100;
while (true) {
stat = read_cpc_co_stat_conf();
seq_state = stat & CPC_Cx_STAT_CONF_SEQSTATE;
seq_state >>= __ffs(CPC_Cx_STAT_CONF_SEQSTATE);
/* U6 == coherent execution, ie. the core is up */
if (seq_state == CPC_Cx_STAT_CONF_SEQSTATE_U6)
break;
/* Delay a little while before we start warning */
if (timeout) {
timeout--;
mdelay(10);
continue;
}
pr_warn("Waiting for core %u to start... STAT_CONF=0x%x\n",
core, stat);
mdelay(1000);
}
mips_cpc_unlock_other();
} else {
/* Take the core out of reset */
write_gcr_co_reset_release(0);
}
mips_cm_unlock_other();
/* The core is now powered up */
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
bitmap_set(core_power, core, 1);
}
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
static void remote_vpe_boot(void *dummy)
{
unsigned core = cpu_core(&current_cpu_data);
struct core_boot_config *core_cfg = &mips_cps_core_bootcfg[core];
mips_cps_boot_vpes(core_cfg, cpu_vpe_id(&current_cpu_data));
}
static int cps_boot_secondary(int cpu, struct task_struct *idle)
{
unsigned core = cpu_core(&cpu_data[cpu]);
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
unsigned vpe_id = cpu_vpe_id(&cpu_data[cpu]);
struct core_boot_config *core_cfg = &mips_cps_core_bootcfg[core];
struct vpe_boot_config *vpe_cfg = &core_cfg->vpe_config[vpe_id];
unsigned long core_entry;
unsigned int remote;
int err;
/* We don't yet support booting CPUs in other clusters */
MIPS: CPS: Fix use of current_cpu_data in preemptible code Commit 1ec9dd80bedc ("MIPS: CPS: Detect CPUs in secondary clusters") added a check in cps_boot_secondary() that the secondary being booted is in the same cluster as the CPU running this code. This check is performed using current_cpu_data without disabling preemption. As such when CONFIG_PREEMPT=y, a BUG is triggered: [ 57.991693] BUG: using smp_processor_id() in preemptible [00000000] code: hotplug/1749 <snip> [ 58.063077] Call Trace: [ 58.065842] [<8040cdb4>] show_stack+0x84/0x114 [ 58.070830] [<80b11b38>] dump_stack+0xf8/0x140 [ 58.075796] [<8079b12c>] check_preemption_disabled+0xec/0x118 [ 58.082204] [<80415110>] cps_boot_secondary+0x84/0x44c [ 58.087935] [<80413a14>] __cpu_up+0x34/0x98 [ 58.092624] [<80434240>] bringup_cpu+0x38/0x114 [ 58.097680] [<80434af0>] cpuhp_invoke_callback+0x168/0x8f0 [ 58.103801] [<804362d0>] _cpu_up+0x154/0x1c8 [ 58.108565] [<804363dc>] do_cpu_up+0x98/0xa8 [ 58.113333] [<808261f8>] device_online+0x84/0xc0 [ 58.118481] [<80826294>] online_store+0x60/0x98 [ 58.123562] [<8062261c>] kernfs_fop_write+0x158/0x1d4 [ 58.129196] [<805a2ae4>] __vfs_write+0x4c/0x168 [ 58.134247] [<805a2dc8>] vfs_write+0xe0/0x190 [ 58.139095] [<805a2fe0>] SyS_write+0x68/0xc4 [ 58.143854] [<80415d58>] syscall_common+0x34/0x58 In reality we don't currently support running the kernel on CPUs not in cluster 0, so the answer to cpu_cluster(&current_cpu_data) will always be 0, even if this task being preempted and continues running on a different CPU. Regardless, the BUG should not be triggered, so fix this by switching to raw_current_cpu_data. When multicluster support lands upstream this check will need removing or changing anyway. Fixes: 1ec9dd80bedc ("MIPS: CPS: Detect CPUs in secondary clusters") Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Reviewed-by: Paul Burton <paul.burton@mips.com> CC: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17563/ Signed-off-by: James Hogan <jhogan@kernel.org>
2017-11-02 00:45:56 +08:00
if (cpu_cluster(&cpu_data[cpu]) != cpu_cluster(&raw_current_cpu_data))
return -ENOSYS;
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
vpe_cfg->pc = (unsigned long)&smp_bootstrap;
vpe_cfg->sp = __KSTK_TOS(idle);
vpe_cfg->gp = (unsigned long)task_thread_info(idle);
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
atomic_or(1 << cpu_vpe_id(&cpu_data[cpu]), &core_cfg->vpe_mask);
preempt_disable();
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
if (!test_bit(core, core_power)) {
/* Boot a VPE on a powered down core */
boot_core(core, vpe_id);
goto out;
}
if (cpu_has_vp) {
mips_cm_lock_other(0, core, vpe_id, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
core_entry = CKSEG1ADDR((unsigned long)mips_cps_core_entry);
write_gcr_co_reset_base(core_entry);
mips_cm_unlock_other();
}
if (!cpus_are_siblings(cpu, smp_processor_id())) {
/* Boot a VPE on another powered up core */
for (remote = 0; remote < NR_CPUS; remote++) {
if (!cpus_are_siblings(cpu, remote))
continue;
if (cpu_online(remote))
break;
}
if (remote >= NR_CPUS) {
pr_crit("No online CPU in core %u to start CPU%d\n",
core, cpu);
goto out;
}
MIPS: smp-cps: rework core/VPE initialisation When hotplug and/or a powered down idle state are supported cases will arise where a non-zero VPE must be brought online without VPE 0, and it where multiple VPEs must be onlined simultaneously. This patch prepares for that by: - Splitting struct boot_config into core & VPE boot config structures, allocated one per core or VPE respectively. This allows for multiple VPEs to be onlined simultaneously without clobbering each others configuration. - Indicating which VPEs should be online within a core at any given time using a bitmap. This allows multiple VPEs to be brought online simultaneously and also indicates to VPE 0 whether it should halt after starting any non-zero VPEs that should be online within the core. For example if all VPEs within a core are offlined via hotplug and the user onlines the second VPE within that core: 1) The core will be powered up. 2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to initialise the core. 3) VPE 0 will start VPE 1 because its bit is set in the cores bitmap. 4) VPE 0 will halt itself because its bit is clear in the cores bitmap. - Moving the core & VPE initialisation to assembly code which does not make any use of the stack. This is because if a non-zero VPE is to be brought online in a powered down core then when VPE 0 of that core runs it may not have a valid stack, and even if it did then it's messy to run through parts of generic kernel code on VPE 0 before starting the correct VPE. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-14 19:04:27 +08:00
err = smp_call_function_single(remote, remote_vpe_boot,
NULL, 1);
if (err)
panic("Failed to call remote CPU\n");
goto out;
}
BUG_ON(!cpu_has_mipsmt && !cpu_has_vp);
/* Boot a VPE on this core */
mips_cps_boot_vpes(core_cfg, vpe_id);
out:
preempt_enable();
return 0;
}
static void cps_init_secondary(void)
{
int core = cpu_core(&current_cpu_data);
/* Disable MT - we only want to run 1 TC per VPE */
if (cpu_has_mipsmt)
dmt();
if (mips_cm_revision() >= CM_REV_CM3) {
unsigned int ident = read_gic_vl_ident();
/*
* Ensure that our calculation of the VP ID matches up with
* what the GIC reports, otherwise we'll have configured
* interrupts incorrectly.
*/
BUG_ON(ident != mips_cm_vp_id(smp_processor_id()));
}
if (core > 0 && !read_gcr_cl_coherence())
pr_warn("Core %u is not in coherent domain\n", core);
if (cpu_has_veic)
clear_c0_status(ST0_IM);
else
change_c0_status(ST0_IM, STATUSF_IP2 | STATUSF_IP3 |
STATUSF_IP4 | STATUSF_IP5 |
STATUSF_IP6 | STATUSF_IP7);
}
static void cps_smp_finish(void)
{
write_c0_compare(read_c0_count() + (8 * mips_hpt_frequency / HZ));
#ifdef CONFIG_MIPS_MT_FPAFF
/* If we have an FPU, enroll ourselves in the FPU-full mask */
if (cpu_has_fpu)
cpumask_set_cpu(smp_processor_id(), &mt_fpu_cpumask);
#endif /* CONFIG_MIPS_MT_FPAFF */
local_irq_enable();
}
#if defined(CONFIG_HOTPLUG_CPU) || defined(CONFIG_KEXEC)
enum cpu_death {
CPU_DEATH_HALT,
CPU_DEATH_POWER,
};
static void cps_shutdown_this_cpu(enum cpu_death death)
{
unsigned int cpu, core, vpe_id;
cpu = smp_processor_id();
core = cpu_core(&cpu_data[cpu]);
if (death == CPU_DEATH_HALT) {
vpe_id = cpu_vpe_id(&cpu_data[cpu]);
pr_debug("Halting core %d VP%d\n", core, vpe_id);
if (cpu_has_mipsmt) {
/* Halt this TC */
write_c0_tchalt(TCHALT_H);
instruction_hazard();
} else if (cpu_has_vp) {
write_cpc_cl_vp_stop(1 << vpe_id);
/* Ensure that the VP_STOP register is written */
wmb();
}
} else {
if (IS_ENABLED(CONFIG_HOTPLUG_CPU)) {
pr_debug("Gating power to core %d\n", core);
/* Power down the core */
cps_pm_enter_state(CPS_PM_POWER_GATED);
}
}
}
#ifdef CONFIG_KEXEC
static void cps_kexec_nonboot_cpu(void)
{
if (cpu_has_mipsmt || cpu_has_vp)
cps_shutdown_this_cpu(CPU_DEATH_HALT);
else
cps_shutdown_this_cpu(CPU_DEATH_POWER);
}
#endif /* CONFIG_KEXEC */
#endif /* CONFIG_HOTPLUG_CPU || CONFIG_KEXEC */
#ifdef CONFIG_HOTPLUG_CPU
static int cps_cpu_disable(void)
{
unsigned cpu = smp_processor_id();
struct core_boot_config *core_cfg;
if (!cps_pm_support_state(CPS_PM_POWER_GATED))
return -EINVAL;
core_cfg = &mips_cps_core_bootcfg[cpu_core(&current_cpu_data)];
atomic_sub(1 << cpu_vpe_id(&current_cpu_data), &core_cfg->vpe_mask);
smp_mb__after_atomic();
set_cpu_online(cpu, false);
calculate_cpu_foreign_map();
irq_migrate_all_off_this_cpu();
return 0;
}
static unsigned cpu_death_sibling;
static enum cpu_death cpu_death;
void play_dead(void)
{
unsigned int cpu;
local_irq_disable();
idle_task_exit();
cpu = smp_processor_id();
cpu_death = CPU_DEATH_POWER;
pr_debug("CPU%d going offline\n", cpu);
if (cpu_has_mipsmt || cpu_has_vp) {
/* Look for another online VPE within the core */
for_each_online_cpu(cpu_death_sibling) {
if (!cpus_are_siblings(cpu, cpu_death_sibling))
continue;
/*
* There is an online VPE within the core. Just halt
* this TC and leave the core alone.
*/
cpu_death = CPU_DEATH_HALT;
break;
}
}
/* This CPU has chosen its way out */
(void)cpu_report_death();
cps_shutdown_this_cpu(cpu_death);
/* This should never be reached */
panic("Failed to offline CPU %u", cpu);
}
static void wait_for_sibling_halt(void *ptr_cpu)
{
unsigned cpu = (unsigned long)ptr_cpu;
unsigned vpe_id = cpu_vpe_id(&cpu_data[cpu]);
unsigned halted;
unsigned long flags;
do {
local_irq_save(flags);
settc(vpe_id);
halted = read_tc_c0_tchalt();
local_irq_restore(flags);
} while (!(halted & TCHALT_H));
}
static void cps_cpu_die(unsigned int cpu)
{
unsigned core = cpu_core(&cpu_data[cpu]);
unsigned int vpe_id = cpu_vpe_id(&cpu_data[cpu]);
ktime_t fail_time;
unsigned stat;
int err;
/* Wait for the cpu to choose its way out */
if (!cpu_wait_death(cpu, 5)) {
pr_err("CPU%u: didn't offline\n", cpu);
return;
}
/*
* Now wait for the CPU to actually offline. Without doing this that
* offlining may race with one or more of:
*
* - Onlining the CPU again.
* - Powering down the core if another VPE within it is offlined.
* - A sibling VPE entering a non-coherent state.
*
* In the non-MT halt case (ie. infinite loop) the CPU is doing nothing
* with which we could race, so do nothing.
*/
if (cpu_death == CPU_DEATH_POWER) {
/*
* Wait for the core to enter a powered down or clock gated
* state, the latter happening when a JTAG probe is connected
* in which case the CPC will refuse to power down the core.
*/
fail_time = ktime_add_ms(ktime_get(), 2000);
do {
mips_cm_lock_other(0, core, 0, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
mips_cpc_lock_other(core);
stat = read_cpc_co_stat_conf();
stat &= CPC_Cx_STAT_CONF_SEQSTATE;
stat >>= __ffs(CPC_Cx_STAT_CONF_SEQSTATE);
mips_cpc_unlock_other();
mips_cm_unlock_other();
if (stat == CPC_Cx_STAT_CONF_SEQSTATE_D0 ||
stat == CPC_Cx_STAT_CONF_SEQSTATE_D2 ||
stat == CPC_Cx_STAT_CONF_SEQSTATE_U2)
break;
/*
* The core ought to have powered down, but didn't &
* now we don't really know what state it's in. It's
* likely that its _pwr_up pin has been wired to logic
* 1 & it powered back up as soon as we powered it
* down...
*
* The best we can do is warn the user & continue in
* the hope that the core is doing nothing harmful &
* might behave properly if we online it later.
*/
if (WARN(ktime_after(ktime_get(), fail_time),
"CPU%u hasn't powered down, seq. state %u\n",
cpu, stat))
break;
} while (1);
/* Indicate the core is powered off */
bitmap_clear(core_power, core, 1);
} else if (cpu_has_mipsmt) {
/*
* Have a CPU with access to the offlined CPUs registers wait
* for its TC to halt.
*/
err = smp_call_function_single(cpu_death_sibling,
wait_for_sibling_halt,
(void *)(unsigned long)cpu, 1);
if (err)
panic("Failed to call remote sibling CPU\n");
} else if (cpu_has_vp) {
do {
mips_cm_lock_other(0, core, vpe_id, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
stat = read_cpc_co_vp_running();
mips_cm_unlock_other();
} while (stat & (1 << vpe_id));
}
}
#endif /* CONFIG_HOTPLUG_CPU */
MIPS: SMP: Constify smp ops smp_ops providers do not modify their ops structures, so they should be made const for robustness. Since currently the MIPS kernel is not mapped with memory protection, this does not in itself provide any security benefit, but it still makes sense to make this change. There are also slight code size efficincies from the structure being made read-only, saving 128 bytes of kernel text on a pistachio_defconfig. Before: text data bss dec hex filename 7187239 1772752 470224 9430215 8fe4c7 vmlinux After: text data bss dec hex filename 7187111 1772752 470224 9430087 8fe447 vmlinux Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com> Cc: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Doug Ledford <dledford@redhat.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Joe Perches <joe@perches.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Steven J. Hill <steven.hill@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/16784/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-07-19 16:21:03 +08:00
static const struct plat_smp_ops cps_smp_ops = {
.smp_setup = cps_smp_setup,
.prepare_cpus = cps_prepare_cpus,
.boot_secondary = cps_boot_secondary,
.init_secondary = cps_init_secondary,
.smp_finish = cps_smp_finish,
.send_ipi_single = mips_smp_send_ipi_single,
.send_ipi_mask = mips_smp_send_ipi_mask,
#ifdef CONFIG_HOTPLUG_CPU
.cpu_disable = cps_cpu_disable,
.cpu_die = cps_cpu_die,
#endif
#ifdef CONFIG_KEXEC
.kexec_nonboot_cpu = cps_kexec_nonboot_cpu,
#endif
};
bool mips_cps_smp_in_use(void)
{
MIPS: SMP: Constify smp ops smp_ops providers do not modify their ops structures, so they should be made const for robustness. Since currently the MIPS kernel is not mapped with memory protection, this does not in itself provide any security benefit, but it still makes sense to make this change. There are also slight code size efficincies from the structure being made read-only, saving 128 bytes of kernel text on a pistachio_defconfig. Before: text data bss dec hex filename 7187239 1772752 470224 9430215 8fe4c7 vmlinux After: text data bss dec hex filename 7187111 1772752 470224 9430087 8fe447 vmlinux Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com> Cc: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Doug Ledford <dledford@redhat.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Joe Perches <joe@perches.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Steven J. Hill <steven.hill@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/16784/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-07-19 16:21:03 +08:00
extern const struct plat_smp_ops *mp_ops;
return mp_ops == &cps_smp_ops;
}
int register_cps_smp_ops(void)
{
if (!mips_cm_present()) {
pr_warn("MIPS CPS SMP unable to proceed without a CM\n");
return -ENODEV;
}
/* check we have a GIC - we need one for IPIs */
MIPS: CM: Use BIT/GENMASK for register fields, order & drop shifts There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h when declaring macros corresponding to register fields. This patch modifies our definitions to do so. The *_SHF definitions are removed entirely - they duplicate information found in the masks, are infrequently used & can be replaced with use of __ffs() where needed. The *_MSK definitions then lose their _MSK suffix which is now somewhat redundant, and users are modified to match. The field definitions are moved to follow the appropriate register's accessor functions, which helps to keep the field definitions in order & to find the appropriate fields for a given register. Whilst here a comment is added describing each register & including its name, which is helpful both for linking the register back to hardware documentation & for grepping purposes. This also cleans up a couple of issues that became obvious as a result of making the changes described above: - We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony copy of that named GCR_RESET_EXT_BASE - a register which does not exist. The bad definitions were added by commit 497e803ebf98 ("MIPS: smp-cps: Ensure secondary cores start with EVA disabled") and made use of from boot_core(), which is now modified to use the GCR_Cx_RESET_EXT_BASE definitions. - We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly define this as inFo rather than inGo. Now that we don't duplicate field information between _SHF & _MSK definitions, and keep the fields next to the register accessors, it will be much easier to spot & prevent any similar oddities being introduced in the future. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Thomas Gleixner <tglx@linutronix.de Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17001/ Patchwork: https://patchwork.linux-mips.org/patch/17216/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-13 10:49:27 +08:00
if (!(read_gcr_gic_status() & CM_GCR_GIC_STATUS_EX)) {
pr_warn("MIPS CPS SMP unable to proceed without a GIC\n");
return -ENODEV;
}
register_smp_ops(&cps_smp_ops);
return 0;
}