License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
|
|
|
/* SPDX-License-Identifier: GPL-2.0 */
|
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
|
|
|
#ifndef __ASM_ARCH_MFP_PXA2XX_H
|
|
|
|
|
#define __ASM_ARCH_MFP_PXA2XX_H
|
|
|
|
|
|
2019-09-20 19:33:40 +08:00
|
|
|
#include <linux/soc/pxa/mfp.h>
|
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* the following MFP_xxx bit definitions in mfp.h are re-used for pxa2xx:
|
|
|
|
|
*
|
|
|
|
|
* MFP_PIN(x)
|
|
|
|
|
* MFP_AFx
|
|
|
|
|
* MFP_LPM_DRIVE_{LOW, HIGH}
|
|
|
|
|
* MFP_LPM_EDGE_x
|
|
|
|
|
*
|
|
|
|
|
* other MFP_x bit definitions will be ignored
|
|
|
|
|
*
|
|
|
|
|
* and adds the below two bits specifically for pxa2xx:
|
|
|
|
|
*
|
|
|
|
|
* bit 23 - Input/Output (PXA2xx specific)
|
|
|
|
|
* bit 24 - Wakeup Enable(PXA2xx specific)
|
2012-04-12 20:43:28 +08:00
|
|
|
* bit 25 - Keep Output (PXA2xx specific)
|
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#define MFP_DIR_IN (0x0 << 23)
|
|
|
|
|
#define MFP_DIR_OUT (0x1 << 23)
|
|
|
|
|
#define MFP_DIR_MASK (0x1 << 23)
|
|
|
|
|
#define MFP_DIR(x) (((x) >> 23) & 0x1)
|
|
|
|
|
|
2008-03-11 09:46:28 +08:00
|
|
|
#define MFP_LPM_CAN_WAKEUP (0x1 << 24)
|
2012-04-12 20:43:28 +08:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* MFP_LPM_KEEP_OUTPUT must be specified for pins that need to
|
|
|
|
|
* retain their last output level (low or high).
|
|
|
|
|
* Note: MFP_LPM_KEEP_OUTPUT has no effect on pins configured for input.
|
|
|
|
|
*/
|
2010-01-11 21:25:15 +08:00
|
|
|
#define MFP_LPM_KEEP_OUTPUT (0x1 << 25)
|
|
|
|
|
|
2008-03-11 09:46:28 +08:00
|
|
|
#define WAKEUP_ON_EDGE_RISE (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_RISE)
|
|
|
|
|
#define WAKEUP_ON_EDGE_FALL (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_FALL)
|
|
|
|
|
#define WAKEUP_ON_EDGE_BOTH (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_BOTH)
|
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
|
|
|
|
|
|
|
|
/* specifically for enabling wakeup on keypad GPIOs */
|
2008-03-11 09:46:28 +08:00
|
|
|
#define WAKEUP_ON_LEVEL_HIGH (MFP_LPM_CAN_WAKEUP)
|
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
|
|
|
|
|
|
|
|
#define MFP_CFG_IN(pin, af) \
|
|
|
|
|
((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK)) |\
|
|
|
|
|
(MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DIR_IN))
|
|
|
|
|
|
|
|
|
|
/* NOTE: pins configured as output _must_ provide a low power state,
|
|
|
|
|
* and this state should help to minimize the power dissipation.
|
|
|
|
|
*/
|
|
|
|
|
#define MFP_CFG_OUT(pin, af, state) \
|
|
|
|
|
((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK | MFP_LPM_STATE_MASK)) |\
|
|
|
|
|
(MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DIR_OUT | MFP_LPM_##state))
|
|
|
|
|
|
|
|
|
|
/* Common configurations for pxa25x and pxa27x
|
|
|
|
|
*
|
|
|
|
|
* Note: pins configured as GPIO are always initialized to input
|
|
|
|
|
* so not to cause any side effect
|
|
|
|
|
*/
|
|
|
|
|
#define GPIO0_GPIO MFP_CFG_IN(GPIO0, AF0)
|
|
|
|
|
#define GPIO1_GPIO MFP_CFG_IN(GPIO1, AF0)
|
|
|
|
|
#define GPIO9_GPIO MFP_CFG_IN(GPIO9, AF0)
|
|
|
|
|
#define GPIO10_GPIO MFP_CFG_IN(GPIO10, AF0)
|
|
|
|
|
#define GPIO11_GPIO MFP_CFG_IN(GPIO11, AF0)
|
|
|
|
|
#define GPIO12_GPIO MFP_CFG_IN(GPIO12, AF0)
|
|
|
|
|
#define GPIO13_GPIO MFP_CFG_IN(GPIO13, AF0)
|
|
|
|
|
#define GPIO14_GPIO MFP_CFG_IN(GPIO14, AF0)
|
|
|
|
|
#define GPIO15_GPIO MFP_CFG_IN(GPIO15, AF0)
|
|
|
|
|
#define GPIO16_GPIO MFP_CFG_IN(GPIO16, AF0)
|
|
|
|
|
#define GPIO17_GPIO MFP_CFG_IN(GPIO17, AF0)
|
|
|
|
|
#define GPIO18_GPIO MFP_CFG_IN(GPIO18, AF0)
|
|
|
|
|
#define GPIO19_GPIO MFP_CFG_IN(GPIO19, AF0)
|
|
|
|
|
#define GPIO20_GPIO MFP_CFG_IN(GPIO20, AF0)
|
|
|
|
|
#define GPIO21_GPIO MFP_CFG_IN(GPIO21, AF0)
|
|
|
|
|
#define GPIO22_GPIO MFP_CFG_IN(GPIO22, AF0)
|
|
|
|
|
#define GPIO23_GPIO MFP_CFG_IN(GPIO23, AF0)
|
|
|
|
|
#define GPIO24_GPIO MFP_CFG_IN(GPIO24, AF0)
|
|
|
|
|
#define GPIO25_GPIO MFP_CFG_IN(GPIO25, AF0)
|
|
|
|
|
#define GPIO26_GPIO MFP_CFG_IN(GPIO26, AF0)
|
|
|
|
|
#define GPIO27_GPIO MFP_CFG_IN(GPIO27, AF0)
|
|
|
|
|
#define GPIO28_GPIO MFP_CFG_IN(GPIO28, AF0)
|
|
|
|
|
#define GPIO29_GPIO MFP_CFG_IN(GPIO29, AF0)
|
|
|
|
|
#define GPIO30_GPIO MFP_CFG_IN(GPIO30, AF0)
|
|
|
|
|
#define GPIO31_GPIO MFP_CFG_IN(GPIO31, AF0)
|
|
|
|
|
#define GPIO32_GPIO MFP_CFG_IN(GPIO32, AF0)
|
|
|
|
|
#define GPIO33_GPIO MFP_CFG_IN(GPIO33, AF0)
|
|
|
|
|
#define GPIO34_GPIO MFP_CFG_IN(GPIO34, AF0)
|
|
|
|
|
#define GPIO35_GPIO MFP_CFG_IN(GPIO35, AF0)
|
|
|
|
|
#define GPIO36_GPIO MFP_CFG_IN(GPIO36, AF0)
|
|
|
|
|
#define GPIO37_GPIO MFP_CFG_IN(GPIO37, AF0)
|
|
|
|
|
#define GPIO38_GPIO MFP_CFG_IN(GPIO38, AF0)
|
|
|
|
|
#define GPIO39_GPIO MFP_CFG_IN(GPIO39, AF0)
|
|
|
|
|
#define GPIO40_GPIO MFP_CFG_IN(GPIO40, AF0)
|
|
|
|
|
#define GPIO41_GPIO MFP_CFG_IN(GPIO41, AF0)
|
|
|
|
|
#define GPIO42_GPIO MFP_CFG_IN(GPIO42, AF0)
|
|
|
|
|
#define GPIO43_GPIO MFP_CFG_IN(GPIO43, AF0)
|
|
|
|
|
#define GPIO44_GPIO MFP_CFG_IN(GPIO44, AF0)
|
|
|
|
|
#define GPIO45_GPIO MFP_CFG_IN(GPIO45, AF0)
|
|
|
|
|
#define GPIO46_GPIO MFP_CFG_IN(GPIO46, AF0)
|
|
|
|
|
#define GPIO47_GPIO MFP_CFG_IN(GPIO47, AF0)
|
|
|
|
|
#define GPIO48_GPIO MFP_CFG_IN(GPIO48, AF0)
|
|
|
|
|
#define GPIO49_GPIO MFP_CFG_IN(GPIO49, AF0)
|
|
|
|
|
#define GPIO50_GPIO MFP_CFG_IN(GPIO50, AF0)
|
|
|
|
|
#define GPIO51_GPIO MFP_CFG_IN(GPIO51, AF0)
|
|
|
|
|
#define GPIO52_GPIO MFP_CFG_IN(GPIO52, AF0)
|
|
|
|
|
#define GPIO53_GPIO MFP_CFG_IN(GPIO53, AF0)
|
|
|
|
|
#define GPIO54_GPIO MFP_CFG_IN(GPIO54, AF0)
|
|
|
|
|
#define GPIO55_GPIO MFP_CFG_IN(GPIO55, AF0)
|
|
|
|
|
#define GPIO56_GPIO MFP_CFG_IN(GPIO56, AF0)
|
|
|
|
|
#define GPIO57_GPIO MFP_CFG_IN(GPIO57, AF0)
|
|
|
|
|
#define GPIO58_GPIO MFP_CFG_IN(GPIO58, AF0)
|
|
|
|
|
#define GPIO59_GPIO MFP_CFG_IN(GPIO59, AF0)
|
|
|
|
|
#define GPIO60_GPIO MFP_CFG_IN(GPIO60, AF0)
|
|
|
|
|
#define GPIO61_GPIO MFP_CFG_IN(GPIO61, AF0)
|
|
|
|
|
#define GPIO62_GPIO MFP_CFG_IN(GPIO62, AF0)
|
|
|
|
|
#define GPIO63_GPIO MFP_CFG_IN(GPIO63, AF0)
|
|
|
|
|
#define GPIO64_GPIO MFP_CFG_IN(GPIO64, AF0)
|
|
|
|
|
#define GPIO65_GPIO MFP_CFG_IN(GPIO65, AF0)
|
|
|
|
|
#define GPIO66_GPIO MFP_CFG_IN(GPIO66, AF0)
|
|
|
|
|
#define GPIO67_GPIO MFP_CFG_IN(GPIO67, AF0)
|
|
|
|
|
#define GPIO68_GPIO MFP_CFG_IN(GPIO68, AF0)
|
|
|
|
|
#define GPIO69_GPIO MFP_CFG_IN(GPIO69, AF0)
|
|
|
|
|
#define GPIO70_GPIO MFP_CFG_IN(GPIO70, AF0)
|
|
|
|
|
#define GPIO71_GPIO MFP_CFG_IN(GPIO71, AF0)
|
|
|
|
|
#define GPIO72_GPIO MFP_CFG_IN(GPIO72, AF0)
|
|
|
|
|
#define GPIO73_GPIO MFP_CFG_IN(GPIO73, AF0)
|
|
|
|
|
#define GPIO74_GPIO MFP_CFG_IN(GPIO74, AF0)
|
|
|
|
|
#define GPIO75_GPIO MFP_CFG_IN(GPIO75, AF0)
|
|
|
|
|
#define GPIO76_GPIO MFP_CFG_IN(GPIO76, AF0)
|
|
|
|
|
#define GPIO77_GPIO MFP_CFG_IN(GPIO77, AF0)
|
|
|
|
|
#define GPIO78_GPIO MFP_CFG_IN(GPIO78, AF0)
|
|
|
|
|
#define GPIO79_GPIO MFP_CFG_IN(GPIO79, AF0)
|
|
|
|
|
#define GPIO80_GPIO MFP_CFG_IN(GPIO80, AF0)
|
|
|
|
|
#define GPIO81_GPIO MFP_CFG_IN(GPIO81, AF0)
|
|
|
|
|
#define GPIO82_GPIO MFP_CFG_IN(GPIO82, AF0)
|
|
|
|
|
#define GPIO83_GPIO MFP_CFG_IN(GPIO83, AF0)
|
|
|
|
|
#define GPIO84_GPIO MFP_CFG_IN(GPIO84, AF0)
|
|
|
|
|
|
|
|
|
|
extern void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num);
|
2008-06-16 09:47:47 +08:00
|
|
|
extern void pxa2xx_mfp_set_lpm(int mfp, unsigned long lpm);
|
2008-03-11 09:46:28 +08:00
|
|
|
extern int gpio_set_wake(unsigned int gpio, unsigned int on);
|
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 17:16:29 +08:00
|
|
|
#endif /* __ASM_ARCH_MFP_PXA2XX_H */
|