OpenCloudOS-Kernel/arch/arm/boot/dts/omap4-panda-common.dtsi

544 lines
13 KiB
Plaintext
Raw Normal View History

/*
* Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include "elpida_ecb240abacn.dtsi"
/ {
memory {
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1 GB */
};
aliases {
display0 = &dvi0;
display1 = &hdmi0;
};
leds: leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <
&led_wkgpio_pins
>;
heartbeat {
label = "pandaboard::status1";
gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
mmc {
label = "pandaboard::status2";
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
};
};
sound: sound {
compatible = "ti,abe-twl6040";
ti,model = "PandaBoard";
ti,mclk-freq = <38400000>;
ti,mcpdm = <&mcpdm>;
ti,twl6040 = <&twl6040>;
/* Audio routing */
ti,audio-routing =
"Headset Stereophone", "HSOL",
"Headset Stereophone", "HSOR",
"Ext Spk", "HFL",
"Ext Spk", "HFR",
"Line Out", "AUXL",
"Line Out", "AUXR",
"HSMIC", "Headset Mic",
"Headset Mic", "Headset Mic Bias",
"AFML", "Line In",
"AFMR", "Line In";
};
/* HS USB Port 1 Power */
hsusb1_power: hsusb1_power_reg {
compatible = "regulator-fixed";
regulator-name = "hsusb1_vbus";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 1 0>; /* gpio_1 */
startup-delay-us = <70000>;
enable-active-high;
/*
* boot-on is required along with always-on as the
* regulator framework doesn't enable the regulator
* if boot-on is not there.
*/
regulator-always-on;
regulator-boot-on;
};
/* HS USB Host PHY on PORT 1 */
hsusb1_phy: hsusb1_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
vcc-supply = <&hsusb1_power>;
clocks = <&auxclk3_ck>;
clock-names = "main_clk";
clock-frequency = <19200000>;
};
/* regulator for wl12xx on sdio5 */
wl12xx_vmmc: wl12xx_vmmc {
pinctrl-names = "default";
pinctrl-0 = <&wl12xx_gpio>;
compatible = "regulator-fixed";
regulator-name = "vwl1271";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio2 11 0>;
startup-delay-us = <70000>;
enable-active-high;
};
tfp410: encoder@0 {
compatible = "ti,tfp410";
powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tfp410_in: endpoint@0 {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
tfp410_out: endpoint@0 {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
dvi0: connector@0 {
compatible = "dvi-connector";
label = "dvi";
digital;
ddc-i2c-bus = <&i2c3>;
port {
dvi_connector_in: endpoint {
remote-endpoint = <&tfp410_out>;
};
};
};
tpd12s015: encoder@1 {
compatible = "ti,tpd12s015";
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
<&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
<&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tpd12s015_in: endpoint@0 {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
tpd12s015_out: endpoint@0 {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
hdmi0: connector@1 {
compatible = "hdmi-connector";
label = "hdmi";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&tpd12s015_out>;
};
};
};
};
&omap4_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&dss_dpi_pins
&tfp410_pins
&dss_hdmi_pins
&tpd12s015_pins
&hsusbb1_pins
>;
twl6040_pins: pinmux_twl6040_pins {
pinctrl-single,pins = <
0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
>;
};
mcpdm_pins: pinmux_mcpdm_pins {
pinctrl-single,pins = <
0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */
0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */
0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */
0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */
0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
>;
};
mcbsp1_pins: pinmux_mcbsp1_pins {
pinctrl-single,pins = <
0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
>;
};
dss_dpi_pins: pinmux_dss_dpi_pins {
pinctrl-single,pins = <
0x122 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */
0x124 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */
0x126 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */
0x128 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */
0x12a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */
0x12c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */
0x12e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */
0x130 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */
0x132 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */
0x134 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */
0x136 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */
0x174 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */
0x176 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */
0x178 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */
0x17a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */
0x17c (PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */
0x17e (PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */
0x180 (PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */
0x182 (PIN_OUTPUT | MUX_MODE5) /* dispc2_de */
0x184 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */
0x186 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */
0x188 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */
0x18a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */
0x18c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */
0x18e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */
0x190 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */
0x192 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */
0x194 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */
>;
};
tfp410_pins: pinmux_tfp410_pins {
pinctrl-single,pins = <
0x144 (PIN_OUTPUT | MUX_MODE3) /* gpio_0 */
>;
};
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
};
tpd12s015_pins: pinmux_tpd12s015_pins {
pinctrl-single,pins = <
0x22 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
0x48 (PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
>;
};
hsusbb1_pins: pinmux_hsusbb1_pins {
pinctrl-single,pins = <
0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
>;
};
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
>;
};
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
>;
};
i2c3_pins: pinmux_i2c3_pins {
pinctrl-single,pins = <
0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
>;
};
i2c4_pins: pinmux_i2c4_pins {
pinctrl-single,pins = <
0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
>;
};
/*
* wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
* REVISIT: Are the pull-ups needed for GPIO 48 and 49?
*/
wl12xx_gpio: pinmux_wl12xx_gpio {
pinctrl-single,pins = <
0x26 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */
0x2c (PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */
0x30 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */
0x32 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */
>;
};
/* wl12xx GPIO inputs and SDIO pins */
wl12xx_pins: pinmux_wl12xx_pins {
pinctrl-single,pins = <
0x38 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */
0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
>;
};
};
&omap4_pmx_wkup {
led_wkgpio_pins: pinmux_leds_wkpins {
pinctrl-single,pins = <
0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
>;
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
twl: twl@48 {
reg = <0x48>;
/* IRQ# = 7 */
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
};
twl6040: twl@4b {
compatible = "ti,twl6040";
reg = <0x4b>;
pinctrl-names = "default";
pinctrl-0 = <&twl6040_pins>;
/* IRQ# = 119 */
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
vio-supply = <&v1v8>;
v2v1-supply = <&v2v1>;
enable-active-high;
};
};
#include "twl6030.dtsi"
#include "twl6030_omap4.dtsi"
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
clock-frequency = <400000>;
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <100000>;
/*
* Display monitor features are burnt in their EEPROM as EDID data.
* The EEPROM is connected as I2C slave device.
*/
eeprom@50 {
compatible = "ti,eeprom";
reg = <0x50>;
};
};
&i2c4 {
pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins>;
clock-frequency = <400000>;
};
&mmc1 {
vmmc-supply = <&vmmc>;
bus-width = <8>;
};
&mmc2 {
status = "disabled";
};
&mmc3 {
status = "disabled";
};
&mmc4 {
status = "disabled";
};
&mmc5 {
pinctrl-names = "default";
pinctrl-0 = <&wl12xx_pins>;
vmmc-supply = <&wl12xx_vmmc>;
non-removable;
bus-width = <4>;
cap-power-off-card;
#address-cells = <1>;
#size-cells = <0>;
wlcore: wlcore@2 {
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio2>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */
ref-clock-frequency = <38400000>;
};
};
&emif1 {
cs1-used;
device-handle = <&elpida_ECB240ABACN>;
};
&emif2 {
cs1-used;
device-handle = <&elpida_ECB240ABACN>;
};
&mcbsp1 {
pinctrl-names = "default";
pinctrl-0 = <&mcbsp1_pins>;
status = "okay";
};
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
status = "okay";
};
&twl_usb_comparator {
usb-supply = <&vusb>;
};
&uart2 {
ARM: omap: convert wakeupgen to stacked domains OMAP4/5 has been (ab)using the gic_arch_extn to provide wakeup from suspend, and it makes a lot of sense to convert this code to use stacked domains instead. This patch does just this, updating the DT files to actually reflect what the HW provides. BIG FAT WARNING: because the DTs were so far lying by not exposing the WUGEN HW block, kernels with this patch applied won't have any suspend-resume facility when booted with old DTs, and old kernels with updated DTs won't even boot. On a platform with this patch applied, the system looks like this: root@bacon-fat:~# cat /proc/interrupts CPU0 CPU1 16: 0 0 WUGEN 37 gp_timer 19: 233799 155916 GIC 27 arch_timer 23: 0 0 WUGEN 9 l3-dbg-irq 24: 1 0 WUGEN 10 l3-app-irq 27: 282 0 WUGEN 13 omap-dma-engine 44: 0 0 4ae10000.gpio 13 DMA 294: 0 0 WUGEN 20 gpmc 297: 506 0 WUGEN 56 48070000.i2c 298: 0 0 WUGEN 57 48072000.i2c 299: 0 0 WUGEN 61 48060000.i2c 300: 0 0 WUGEN 62 4807a000.i2c 301: 8 0 WUGEN 60 4807c000.i2c 308: 2439 0 WUGEN 74 OMAP UART2 312: 362 0 WUGEN 83 mmc2 313: 502 0 WUGEN 86 mmc0 314: 13 0 WUGEN 94 mmc1 350: 0 0 PRCM pinctrl, pinctrl 406: 35155709 0 GIC 109 ehci_hcd:usb1 407: 0 0 WUGEN 7 palmas 409: 0 0 WUGEN 119 twl6040 410: 0 0 twl6040 5 twl6040_irq_ready 411: 0 0 twl6040 0 twl6040_irq_th IPI0: 0 1 CPU wakeup interrupts IPI1: 0 0 Timer broadcast interrupts IPI2: 95334 902334 Rescheduling interrupts IPI3: 0 0 Function call interrupts IPI4: 479 648 Single function call interrupts IPI5: 0 0 CPU stop interrupts IPI6: 0 0 IRQ work interrupts IPI7: 0 0 completion interrupts Err: 0 Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2015-03-11 23:43:49 +08:00
interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART2_RX>;
};
&uart3 {
ARM: omap: convert wakeupgen to stacked domains OMAP4/5 has been (ab)using the gic_arch_extn to provide wakeup from suspend, and it makes a lot of sense to convert this code to use stacked domains instead. This patch does just this, updating the DT files to actually reflect what the HW provides. BIG FAT WARNING: because the DTs were so far lying by not exposing the WUGEN HW block, kernels with this patch applied won't have any suspend-resume facility when booted with old DTs, and old kernels with updated DTs won't even boot. On a platform with this patch applied, the system looks like this: root@bacon-fat:~# cat /proc/interrupts CPU0 CPU1 16: 0 0 WUGEN 37 gp_timer 19: 233799 155916 GIC 27 arch_timer 23: 0 0 WUGEN 9 l3-dbg-irq 24: 1 0 WUGEN 10 l3-app-irq 27: 282 0 WUGEN 13 omap-dma-engine 44: 0 0 4ae10000.gpio 13 DMA 294: 0 0 WUGEN 20 gpmc 297: 506 0 WUGEN 56 48070000.i2c 298: 0 0 WUGEN 57 48072000.i2c 299: 0 0 WUGEN 61 48060000.i2c 300: 0 0 WUGEN 62 4807a000.i2c 301: 8 0 WUGEN 60 4807c000.i2c 308: 2439 0 WUGEN 74 OMAP UART2 312: 362 0 WUGEN 83 mmc2 313: 502 0 WUGEN 86 mmc0 314: 13 0 WUGEN 94 mmc1 350: 0 0 PRCM pinctrl, pinctrl 406: 35155709 0 GIC 109 ehci_hcd:usb1 407: 0 0 WUGEN 7 palmas 409: 0 0 WUGEN 119 twl6040 410: 0 0 twl6040 5 twl6040_irq_ready 411: 0 0 twl6040 0 twl6040_irq_th IPI0: 0 1 CPU wakeup interrupts IPI1: 0 0 Timer broadcast interrupts IPI2: 95334 902334 Rescheduling interrupts IPI3: 0 0 Function call interrupts IPI4: 479 648 Single function call interrupts IPI5: 0 0 CPU stop interrupts IPI6: 0 0 IRQ work interrupts IPI7: 0 0 completion interrupts Err: 0 Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2015-03-11 23:43:49 +08:00
interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART3_RX>;
};
&uart4 {
ARM: omap: convert wakeupgen to stacked domains OMAP4/5 has been (ab)using the gic_arch_extn to provide wakeup from suspend, and it makes a lot of sense to convert this code to use stacked domains instead. This patch does just this, updating the DT files to actually reflect what the HW provides. BIG FAT WARNING: because the DTs were so far lying by not exposing the WUGEN HW block, kernels with this patch applied won't have any suspend-resume facility when booted with old DTs, and old kernels with updated DTs won't even boot. On a platform with this patch applied, the system looks like this: root@bacon-fat:~# cat /proc/interrupts CPU0 CPU1 16: 0 0 WUGEN 37 gp_timer 19: 233799 155916 GIC 27 arch_timer 23: 0 0 WUGEN 9 l3-dbg-irq 24: 1 0 WUGEN 10 l3-app-irq 27: 282 0 WUGEN 13 omap-dma-engine 44: 0 0 4ae10000.gpio 13 DMA 294: 0 0 WUGEN 20 gpmc 297: 506 0 WUGEN 56 48070000.i2c 298: 0 0 WUGEN 57 48072000.i2c 299: 0 0 WUGEN 61 48060000.i2c 300: 0 0 WUGEN 62 4807a000.i2c 301: 8 0 WUGEN 60 4807c000.i2c 308: 2439 0 WUGEN 74 OMAP UART2 312: 362 0 WUGEN 83 mmc2 313: 502 0 WUGEN 86 mmc0 314: 13 0 WUGEN 94 mmc1 350: 0 0 PRCM pinctrl, pinctrl 406: 35155709 0 GIC 109 ehci_hcd:usb1 407: 0 0 WUGEN 7 palmas 409: 0 0 WUGEN 119 twl6040 410: 0 0 twl6040 5 twl6040_irq_ready 411: 0 0 twl6040 0 twl6040_irq_th IPI0: 0 1 CPU wakeup interrupts IPI1: 0 0 Timer broadcast interrupts IPI2: 95334 902334 Rescheduling interrupts IPI3: 0 0 Function call interrupts IPI4: 479 648 Single function call interrupts IPI5: 0 0 CPU stop interrupts IPI6: 0 0 IRQ work interrupts IPI7: 0 0 completion interrupts Err: 0 Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2015-03-11 23:43:49 +08:00
interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART4_RX>;
};
&usb_otg_hs {
interface-type = <1>;
mode = <3>;
power = <50>;
};
&usbhshost {
port1-mode = "ehci-phy";
};
&usbhsehci {
phys = <&hsusb1_phy>;
};
&dss {
status = "ok";
port {
dpi_out: endpoint {
remote-endpoint = <&tfp410_in>;
data-lines = <24>;
};
};
};
&dsi2 {
status = "ok";
vdd-supply = <&vcxio>;
};
&hdmi {
status = "ok";
vdda-supply = <&vdac>;
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
};
};
};