OpenCloudOS-Kernel/drivers/pci/proc.c

462 lines
9.5 KiB
C
Raw Normal View History

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
// SPDX-License-Identifier: GPL-2.0
/*
* Procfs interface for the PCI bus
*
* Copyright (c) 1997--1999 Martin Mares <mj@ucw.cz>
*/
#include <linux/init.h>
#include <linux/pci.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 16:04:11 +08:00
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <linux/capability.h>
#include <linux/uaccess.h>
#include <linux/security.h>
#include <asm/byteorder.h>
#include "pci.h"
static int proc_initialized; /* = 0 */
static loff_t proc_bus_pci_lseek(struct file *file, loff_t off, int whence)
{
struct pci_dev *dev = PDE_DATA(file_inode(file));
return fixed_size_llseek(file, off, whence, dev->cfg_size);
}
static ssize_t proc_bus_pci_read(struct file *file, char __user *buf,
size_t nbytes, loff_t *ppos)
{
struct pci_dev *dev = PDE_DATA(file_inode(file));
unsigned int pos = *ppos;
unsigned int cnt, size;
/*
* Normal users can read only the standardized portion of the
* configuration space as several chips lock up when trying to read
* undefined locations (think of Intel PIIX4 as a typical example).
*/
if (capable(CAP_SYS_ADMIN))
size = dev->cfg_size;
else if (dev->hdr_type == PCI_HEADER_TYPE_CARDBUS)
size = 128;
else
size = 64;
if (pos >= size)
return 0;
if (nbytes >= size)
nbytes = size;
if (pos + nbytes > size)
nbytes = size - pos;
cnt = nbytes;
Remove 'type' argument from access_ok() function Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument of the user address range verification function since we got rid of the old racy i386-only code to walk page tables by hand. It existed because the original 80386 would not honor the write protect bit when in kernel mode, so you had to do COW by hand before doing any user access. But we haven't supported that in a long time, and these days the 'type' argument is a purely historical artifact. A discussion about extending 'user_access_begin()' to do the range checking resulted this patch, because there is no way we're going to move the old VERIFY_xyz interface to that model. And it's best done at the end of the merge window when I've done most of my merges, so let's just get this done once and for all. This patch was mostly done with a sed-script, with manual fix-ups for the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form. There were a couple of notable cases: - csky still had the old "verify_area()" name as an alias. - the iter_iov code had magical hardcoded knowledge of the actual values of VERIFY_{READ,WRITE} (not that they mattered, since nothing really used it) - microblaze used the type argument for a debug printout but other than those oddities this should be a total no-op patch. I tried to fix up all architectures, did fairly extensive grepping for access_ok() uses, and the changes are trivial, but I may have missed something. Any missed conversion should be trivially fixable, though. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-01-04 10:57:57 +08:00
if (!access_ok(buf, cnt))
return -EINVAL;
pci_config_pm_runtime_get(dev);
if ((pos & 1) && cnt) {
unsigned char val;
pci_user_read_config_byte(dev, pos, &val);
__put_user(val, buf);
buf++;
pos++;
cnt--;
}
if ((pos & 3) && cnt > 2) {
unsigned short val;
pci_user_read_config_word(dev, pos, &val);
__put_user(cpu_to_le16(val), (__le16 __user *) buf);
buf += 2;
pos += 2;
cnt -= 2;
}
while (cnt >= 4) {
unsigned int val;
pci_user_read_config_dword(dev, pos, &val);
__put_user(cpu_to_le32(val), (__le32 __user *) buf);
buf += 4;
pos += 4;
cnt -= 4;
}
if (cnt >= 2) {
unsigned short val;
pci_user_read_config_word(dev, pos, &val);
__put_user(cpu_to_le16(val), (__le16 __user *) buf);
buf += 2;
pos += 2;
cnt -= 2;
}
if (cnt) {
unsigned char val;
pci_user_read_config_byte(dev, pos, &val);
__put_user(val, buf);
buf++;
pos++;
cnt--;
}
pci_config_pm_runtime_put(dev);
*ppos = pos;
return nbytes;
}
static ssize_t proc_bus_pci_write(struct file *file, const char __user *buf,
size_t nbytes, loff_t *ppos)
{
struct inode *ino = file_inode(file);
struct pci_dev *dev = PDE_DATA(ino);
int pos = *ppos;
int size = dev->cfg_size;
int cnt, ret;
ret = security_locked_down(LOCKDOWN_PCI_ACCESS);
if (ret)
return ret;
if (pos >= size)
return 0;
if (nbytes >= size)
nbytes = size;
if (pos + nbytes > size)
nbytes = size - pos;
cnt = nbytes;
Remove 'type' argument from access_ok() function Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument of the user address range verification function since we got rid of the old racy i386-only code to walk page tables by hand. It existed because the original 80386 would not honor the write protect bit when in kernel mode, so you had to do COW by hand before doing any user access. But we haven't supported that in a long time, and these days the 'type' argument is a purely historical artifact. A discussion about extending 'user_access_begin()' to do the range checking resulted this patch, because there is no way we're going to move the old VERIFY_xyz interface to that model. And it's best done at the end of the merge window when I've done most of my merges, so let's just get this done once and for all. This patch was mostly done with a sed-script, with manual fix-ups for the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form. There were a couple of notable cases: - csky still had the old "verify_area()" name as an alias. - the iter_iov code had magical hardcoded knowledge of the actual values of VERIFY_{READ,WRITE} (not that they mattered, since nothing really used it) - microblaze used the type argument for a debug printout but other than those oddities this should be a total no-op patch. I tried to fix up all architectures, did fairly extensive grepping for access_ok() uses, and the changes are trivial, but I may have missed something. Any missed conversion should be trivially fixable, though. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-01-04 10:57:57 +08:00
if (!access_ok(buf, cnt))
return -EINVAL;
pci_config_pm_runtime_get(dev);
if ((pos & 1) && cnt) {
unsigned char val;
__get_user(val, buf);
pci_user_write_config_byte(dev, pos, val);
buf++;
pos++;
cnt--;
}
if ((pos & 3) && cnt > 2) {
__le16 val;
__get_user(val, (__le16 __user *) buf);
pci_user_write_config_word(dev, pos, le16_to_cpu(val));
buf += 2;
pos += 2;
cnt -= 2;
}
while (cnt >= 4) {
__le32 val;
__get_user(val, (__le32 __user *) buf);
pci_user_write_config_dword(dev, pos, le32_to_cpu(val));
buf += 4;
pos += 4;
cnt -= 4;
}
if (cnt >= 2) {
__le16 val;
__get_user(val, (__le16 __user *) buf);
pci_user_write_config_word(dev, pos, le16_to_cpu(val));
buf += 2;
pos += 2;
cnt -= 2;
}
if (cnt) {
unsigned char val;
__get_user(val, buf);
pci_user_write_config_byte(dev, pos, val);
buf++;
pos++;
cnt--;
}
pci_config_pm_runtime_put(dev);
*ppos = pos;
i_size_write(ino, dev->cfg_size);
return nbytes;
}
struct pci_filp_private {
enum pci_mmap_state mmap_state;
int write_combine;
};
static long proc_bus_pci_ioctl(struct file *file, unsigned int cmd,
unsigned long arg)
{
struct pci_dev *dev = PDE_DATA(file_inode(file));
#ifdef HAVE_PCI_MMAP
struct pci_filp_private *fpriv = file->private_data;
#endif /* HAVE_PCI_MMAP */
int ret = 0;
ret = security_locked_down(LOCKDOWN_PCI_ACCESS);
if (ret)
return ret;
switch (cmd) {
case PCIIOC_CONTROLLER:
ret = pci_domain_nr(dev->bus);
break;
#ifdef HAVE_PCI_MMAP
case PCIIOC_MMAP_IS_IO:
if (!arch_can_pci_mmap_io())
return -EINVAL;
fpriv->mmap_state = pci_mmap_io;
break;
case PCIIOC_MMAP_IS_MEM:
fpriv->mmap_state = pci_mmap_mem;
break;
case PCIIOC_WRITE_COMBINE:
if (arch_can_pci_mmap_wc()) {
if (arg)
fpriv->write_combine = 1;
else
fpriv->write_combine = 0;
break;
}
/* If arch decided it can't, fall through... */
#endif /* HAVE_PCI_MMAP */
/* fall through */
default:
ret = -EINVAL;
break;
}
return ret;
}
#ifdef HAVE_PCI_MMAP
static int proc_bus_pci_mmap(struct file *file, struct vm_area_struct *vma)
{
struct pci_dev *dev = PDE_DATA(file_inode(file));
struct pci_filp_private *fpriv = file->private_data;
int i, ret, write_combine = 0, res_bit = IORESOURCE_MEM;
if (!capable(CAP_SYS_RAWIO) ||
security_locked_down(LOCKDOWN_PCI_ACCESS))
return -EPERM;
if (fpriv->mmap_state == pci_mmap_io) {
if (!arch_can_pci_mmap_io())
return -EINVAL;
res_bit = IORESOURCE_IO;
}
/* Make sure the caller is mapping a real resource for this device */
for (i = 0; i < PCI_ROM_RESOURCE; i++) {
if (dev->resource[i].flags & res_bit &&
pci_mmap_fits(dev, i, vma, PCI_MMAP_PROCFS))
break;
}
if (i >= PCI_ROM_RESOURCE)
return -ENODEV;
if (fpriv->mmap_state == pci_mmap_mem &&
fpriv->write_combine) {
if (dev->resource[i].flags & IORESOURCE_PREFETCH)
write_combine = 1;
else
return -EINVAL;
}
ret = pci_mmap_page_range(dev, i, vma,
PCI: Ignore write combining when mapping I/O port space PCI exposes files like /proc/bus/pci/00/00.0 in procfs. These files support operations like this: ioctl(fd, PCIIOC_MMAP_IS_IO); # request I/O port space ioctl(fd, PCIIOC_WRITE_COMBINE, 1); # request write-combining mmap(fd, ...) Write combining is useful on PCI memory space, but I don't think it makes sense on PCI I/O port space. We *could* change proc_bus_pci_ioctl() to make it impossible to set mmap_state == pci_mmap_io and write_combine at the same time, but that would break the following sequence, which is currently legal: mmap(fd, ...) # default is I/O, non-combining ioctl(fd, PCIIOC_WRITE_COMBINE, 1); # request write-combining ioctl(fd, PCIIOC_MMAP_IS_MEM); # request memory space mmap(fd, ...) # get write-combining mapping Ignore the write-combining flag when mapping I/O port space. This patch should have no functional effect, based on this analysis of all implementations of pci_mmap_page_range(): - ia64 mips parisc sh unicore32 x86 do not support mapping of I/O port space at all. - arm cris microblaze mn10300 sparc xtensa support mapping of I/O port space, but ignore the write_combine argument to pci_mmap_page_range(). - powerpc supports mapping of I/O port space and uses write_combine, and it disables write combining for I/O port space in __pci_mmap_set_pgprot(). This patch makes it possible to remove __pci_mmap_set_pgprot() from powerpc, which simplifies that path. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2016-06-09 03:46:54 +08:00
fpriv->mmap_state, write_combine);
if (ret < 0)
return ret;
return 0;
}
static int proc_bus_pci_open(struct inode *inode, struct file *file)
{
struct pci_filp_private *fpriv = kmalloc(sizeof(*fpriv), GFP_KERNEL);
if (!fpriv)
return -ENOMEM;
fpriv->mmap_state = pci_mmap_io;
fpriv->write_combine = 0;
file->private_data = fpriv;
return 0;
}
static int proc_bus_pci_release(struct inode *inode, struct file *file)
{
kfree(file->private_data);
file->private_data = NULL;
return 0;
}
#endif /* HAVE_PCI_MMAP */
static const struct file_operations proc_bus_pci_operations = {
.owner = THIS_MODULE,
.llseek = proc_bus_pci_lseek,
.read = proc_bus_pci_read,
.write = proc_bus_pci_write,
.unlocked_ioctl = proc_bus_pci_ioctl,
.compat_ioctl = proc_bus_pci_ioctl,
#ifdef HAVE_PCI_MMAP
.open = proc_bus_pci_open,
.release = proc_bus_pci_release,
.mmap = proc_bus_pci_mmap,
#ifdef HAVE_ARCH_PCI_GET_UNMAPPED_AREA
.get_unmapped_area = get_pci_unmapped_area,
#endif /* HAVE_ARCH_PCI_GET_UNMAPPED_AREA */
#endif /* HAVE_PCI_MMAP */
};
/* iterator */
static void *pci_seq_start(struct seq_file *m, loff_t *pos)
{
struct pci_dev *dev = NULL;
loff_t n = *pos;
for_each_pci_dev(dev) {
if (!n--)
break;
}
return dev;
}
static void *pci_seq_next(struct seq_file *m, void *v, loff_t *pos)
{
struct pci_dev *dev = v;
(*pos)++;
dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev);
return dev;
}
static void pci_seq_stop(struct seq_file *m, void *v)
{
if (v) {
struct pci_dev *dev = v;
pci_dev_put(dev);
}
}
static int show_device(struct seq_file *m, void *v)
{
const struct pci_dev *dev = v;
const struct pci_driver *drv;
int i;
if (dev == NULL)
return 0;
drv = pci_dev_driver(dev);
seq_printf(m, "%02x%02x\t%04x%04x\t%x",
dev->bus->number,
dev->devfn,
dev->vendor,
dev->device,
dev->irq);
/* only print standard and ROM resources to preserve compatibility */
for (i = 0; i <= PCI_ROM_RESOURCE; i++) {
resource_size_t start, end;
pci_resource_to_user(dev, i, &dev->resource[i], &start, &end);
seq_printf(m, "\t%16llx",
(unsigned long long)(start |
(dev->resource[i].flags & PCI_REGION_FLAG_MASK)));
}
for (i = 0; i <= PCI_ROM_RESOURCE; i++) {
resource_size_t start, end;
pci_resource_to_user(dev, i, &dev->resource[i], &start, &end);
seq_printf(m, "\t%16llx",
dev->resource[i].start < dev->resource[i].end ?
(unsigned long long)(end - start) + 1 : 0);
}
seq_putc(m, '\t');
if (drv)
seq_puts(m, drv->name);
seq_putc(m, '\n');
return 0;
}
static const struct seq_operations proc_bus_pci_devices_op = {
.start = pci_seq_start,
.next = pci_seq_next,
.stop = pci_seq_stop,
.show = show_device
};
static struct proc_dir_entry *proc_bus_pci_dir;
int pci_proc_attach_device(struct pci_dev *dev)
{
struct pci_bus *bus = dev->bus;
struct proc_dir_entry *e;
char name[16];
if (!proc_initialized)
return -EACCES;
if (!bus->procdir) {
if (pci_proc_domain(bus)) {
sprintf(name, "%04x:%02x", pci_domain_nr(bus),
bus->number);
} else {
sprintf(name, "%02x", bus->number);
}
bus->procdir = proc_mkdir(name, proc_bus_pci_dir);
if (!bus->procdir)
return -ENOMEM;
}
sprintf(name, "%02x.%x", PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
e = proc_create_data(name, S_IFREG | S_IRUGO | S_IWUSR, bus->procdir,
&proc_bus_pci_operations, dev);
if (!e)
return -ENOMEM;
proc_set_size(e, dev->cfg_size);
dev->procent = e;
return 0;
}
int pci_proc_detach_device(struct pci_dev *dev)
{
proc_remove(dev->procent);
dev->procent = NULL;
return 0;
}
int pci_proc_detach_bus(struct pci_bus *bus)
{
proc_remove(bus->procdir);
return 0;
}
static int __init pci_proc_init(void)
{
struct pci_dev *dev = NULL;
proc_bus_pci_dir = proc_mkdir("bus/pci", NULL);
proc_create_seq("devices", 0, proc_bus_pci_dir,
&proc_bus_pci_devices_op);
proc_initialized = 1;
for_each_pci_dev(dev)
pci_proc_attach_device(dev);
return 0;
}
device_initcall(pci_proc_init);