2018-10-09 19:12:06 +08:00
|
|
|
// SPDX-License-Identifier: GPL-2.0
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
/*
|
|
|
|
|
* Copyright (C) 2016 CNEX Labs
|
|
|
|
|
* Initial release: Javier Gonzalez <javier@cnexlabs.com>
|
|
|
|
|
* Matias Bjorling <matias@cnexlabs.com>
|
|
|
|
|
*
|
|
|
|
|
* This program is free software; you can redistribute it and/or
|
|
|
|
|
* modify it under the terms of the GNU General Public License version
|
|
|
|
|
* 2 as published by the Free Software Foundation.
|
|
|
|
|
*
|
|
|
|
|
* This program is distributed in the hope that it will be useful, but
|
|
|
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
|
|
|
* General Public License for more details.
|
|
|
|
|
*
|
|
|
|
|
* pblk-read.c - pblk's read path
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#include "pblk.h"
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* There is no guarantee that the value read from cache has not been updated and
|
|
|
|
|
* resides at another location in the cache. We guarantee though that if the
|
|
|
|
|
* value is read from the cache, it belongs to the mapped lba. In order to
|
|
|
|
|
* guarantee and order between writes and reads are ordered, a flush must be
|
|
|
|
|
* issued.
|
|
|
|
|
*/
|
|
|
|
|
static int pblk_read_from_cache(struct pblk *pblk, struct bio *bio,
|
|
|
|
|
sector_t lba, struct ppa_addr ppa,
|
2017-07-28 21:13:16 +08:00
|
|
|
int bio_iter, bool advanced_bio)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
/* Callers must ensure that the ppa points to a cache address */
|
|
|
|
|
BUG_ON(pblk_ppa_empty(ppa));
|
|
|
|
|
BUG_ON(!pblk_addr_in_cache(ppa));
|
|
|
|
|
#endif
|
|
|
|
|
|
2017-07-28 21:13:16 +08:00
|
|
|
return pblk_rb_copy_to_bio(&pblk->rwb, bio, lba, ppa,
|
|
|
|
|
bio_iter, advanced_bio);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static void pblk_read_ppalist_rq(struct pblk *pblk, struct nvm_rq *rqd,
|
2018-06-01 22:41:11 +08:00
|
|
|
struct bio *bio, sector_t blba,
|
|
|
|
|
unsigned long *read_bitmap)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
2018-12-12 03:16:23 +08:00
|
|
|
void *meta_list = rqd->meta_list;
|
2018-10-09 19:11:37 +08:00
|
|
|
struct ppa_addr ppas[NVM_MAX_VLBA];
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
int nr_secs = rqd->nr_ppas;
|
2017-07-28 21:13:16 +08:00
|
|
|
bool advanced_bio = false;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
int i, j = 0;
|
|
|
|
|
|
|
|
|
|
pblk_lookup_l2p_seq(pblk, ppas, blba, nr_secs);
|
|
|
|
|
|
|
|
|
|
for (i = 0; i < nr_secs; i++) {
|
|
|
|
|
struct ppa_addr p = ppas[i];
|
2018-12-12 03:16:23 +08:00
|
|
|
struct pblk_sec_meta *meta = pblk_get_meta(pblk, meta_list, i);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
sector_t lba = blba + i;
|
|
|
|
|
|
|
|
|
|
retry:
|
|
|
|
|
if (pblk_ppa_empty(p)) {
|
2018-12-12 03:16:23 +08:00
|
|
|
__le64 addr_empty = cpu_to_le64(ADDR_EMPTY);
|
|
|
|
|
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
WARN_ON(test_and_set_bit(i, read_bitmap));
|
2018-12-12 03:16:23 +08:00
|
|
|
meta->lba = addr_empty;
|
2017-07-28 21:13:16 +08:00
|
|
|
|
|
|
|
|
if (unlikely(!advanced_bio)) {
|
|
|
|
|
bio_advance(bio, (i) * PBLK_EXPOSED_PAGE_SIZE);
|
|
|
|
|
advanced_bio = true;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
goto next;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* Try to read from write buffer. The address is later checked
|
|
|
|
|
* on the write buffer to prevent retrieving overwritten data.
|
|
|
|
|
*/
|
|
|
|
|
if (pblk_addr_in_cache(p)) {
|
2017-07-28 21:13:16 +08:00
|
|
|
if (!pblk_read_from_cache(pblk, bio, lba, p, i,
|
|
|
|
|
advanced_bio)) {
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
pblk_lookup_l2p_seq(pblk, &p, lba, 1);
|
|
|
|
|
goto retry;
|
|
|
|
|
}
|
|
|
|
|
WARN_ON(test_and_set_bit(i, read_bitmap));
|
2018-12-12 03:16:23 +08:00
|
|
|
meta->lba = cpu_to_le64(lba);
|
2017-07-28 21:13:16 +08:00
|
|
|
advanced_bio = true;
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
2017-06-26 17:57:13 +08:00
|
|
|
atomic_long_inc(&pblk->cache_reads);
|
|
|
|
|
#endif
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
} else {
|
|
|
|
|
/* Read from media non-cached sectors */
|
|
|
|
|
rqd->ppa_list[j++] = p;
|
|
|
|
|
}
|
|
|
|
|
|
2017-07-28 21:13:16 +08:00
|
|
|
next:
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
if (advanced_bio)
|
|
|
|
|
bio_advance(bio, PBLK_EXPOSED_PAGE_SIZE);
|
|
|
|
|
}
|
|
|
|
|
|
2017-06-26 17:57:20 +08:00
|
|
|
if (pblk_io_aligned(pblk, nr_secs))
|
2018-10-09 19:11:32 +08:00
|
|
|
rqd->is_seq = 1;
|
2017-06-26 17:57:20 +08:00
|
|
|
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
atomic_long_add(nr_secs, &pblk->inflight_reads);
|
|
|
|
|
#endif
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
2018-06-01 21:04:18 +08:00
|
|
|
static void pblk_read_check_seq(struct pblk *pblk, struct nvm_rq *rqd,
|
|
|
|
|
sector_t blba)
|
2017-10-13 20:46:22 +08:00
|
|
|
{
|
2018-12-12 03:16:23 +08:00
|
|
|
void *meta_list = rqd->meta_list;
|
2018-06-01 21:04:18 +08:00
|
|
|
int nr_lbas = rqd->nr_ppas;
|
2017-10-13 20:46:22 +08:00
|
|
|
int i;
|
|
|
|
|
|
2018-12-12 03:16:26 +08:00
|
|
|
if (!pblk_is_oob_meta_supported(pblk))
|
|
|
|
|
return;
|
|
|
|
|
|
2017-10-13 20:46:22 +08:00
|
|
|
for (i = 0; i < nr_lbas; i++) {
|
2018-12-12 03:16:23 +08:00
|
|
|
struct pblk_sec_meta *meta = pblk_get_meta(pblk, meta_list, i);
|
|
|
|
|
u64 lba = le64_to_cpu(meta->lba);
|
2017-10-13 20:46:22 +08:00
|
|
|
|
|
|
|
|
if (lba == ADDR_EMPTY)
|
|
|
|
|
continue;
|
|
|
|
|
|
2018-06-01 21:04:18 +08:00
|
|
|
if (lba != blba + i) {
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
2018-10-09 19:11:46 +08:00
|
|
|
struct ppa_addr *ppa_list = nvm_rq_to_ppa_list(rqd);
|
2018-06-01 21:04:18 +08:00
|
|
|
|
2018-10-09 19:11:46 +08:00
|
|
|
print_ppa(pblk, &ppa_list[i], "seq", i);
|
2018-06-01 21:04:18 +08:00
|
|
|
#endif
|
2018-07-13 16:48:42 +08:00
|
|
|
pblk_err(pblk, "corrupted read LBA (%llu/%llu)\n",
|
2018-06-01 21:04:18 +08:00
|
|
|
lba, (u64)blba + i);
|
|
|
|
|
WARN_ON(1);
|
|
|
|
|
}
|
2017-10-13 20:46:22 +08:00
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
2018-06-01 21:04:17 +08:00
|
|
|
/*
|
|
|
|
|
* There can be holes in the lba list.
|
|
|
|
|
*/
|
2018-06-01 21:04:18 +08:00
|
|
|
static void pblk_read_check_rand(struct pblk *pblk, struct nvm_rq *rqd,
|
|
|
|
|
u64 *lba_list, int nr_lbas)
|
2018-06-01 21:04:17 +08:00
|
|
|
{
|
2018-12-12 03:16:23 +08:00
|
|
|
void *meta_lba_list = rqd->meta_list;
|
2018-06-01 21:04:17 +08:00
|
|
|
int i, j;
|
|
|
|
|
|
2018-12-12 03:16:26 +08:00
|
|
|
if (!pblk_is_oob_meta_supported(pblk))
|
|
|
|
|
return;
|
|
|
|
|
|
2018-06-01 21:04:17 +08:00
|
|
|
for (i = 0, j = 0; i < nr_lbas; i++) {
|
2018-12-12 03:16:23 +08:00
|
|
|
struct pblk_sec_meta *meta = pblk_get_meta(pblk,
|
|
|
|
|
meta_lba_list, j);
|
2018-06-01 21:04:17 +08:00
|
|
|
u64 lba = lba_list[i];
|
|
|
|
|
u64 meta_lba;
|
|
|
|
|
|
|
|
|
|
if (lba == ADDR_EMPTY)
|
|
|
|
|
continue;
|
|
|
|
|
|
2018-12-12 03:16:23 +08:00
|
|
|
meta_lba = le64_to_cpu(meta->lba);
|
2018-06-01 21:04:17 +08:00
|
|
|
|
|
|
|
|
if (lba != meta_lba) {
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
2018-10-09 19:11:46 +08:00
|
|
|
struct ppa_addr *ppa_list = nvm_rq_to_ppa_list(rqd);
|
2018-06-01 21:04:18 +08:00
|
|
|
|
2018-10-09 19:11:49 +08:00
|
|
|
print_ppa(pblk, &ppa_list[j], "rnd", j);
|
2018-06-01 21:04:18 +08:00
|
|
|
#endif
|
2018-07-13 16:48:42 +08:00
|
|
|
pblk_err(pblk, "corrupted read LBA (%llu/%llu)\n",
|
2018-10-09 19:11:49 +08:00
|
|
|
meta_lba, lba);
|
2018-06-01 21:04:17 +08:00
|
|
|
WARN_ON(1);
|
|
|
|
|
}
|
2018-06-01 21:04:18 +08:00
|
|
|
|
|
|
|
|
j++;
|
2018-06-01 21:04:17 +08:00
|
|
|
}
|
2018-06-01 21:04:18 +08:00
|
|
|
|
|
|
|
|
WARN_ONCE(j != rqd->nr_ppas, "pblk: corrupted random request\n");
|
2018-06-01 21:04:17 +08:00
|
|
|
}
|
|
|
|
|
|
2017-10-13 20:46:23 +08:00
|
|
|
static void pblk_end_user_read(struct bio *bio)
|
|
|
|
|
{
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
2017-10-13 20:46:23 +08:00
|
|
|
WARN_ONCE(bio->bi_status, "pblk: corrupted read bio\n");
|
|
|
|
|
#endif
|
|
|
|
|
bio_endio(bio);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static void __pblk_end_io_read(struct pblk *pblk, struct nvm_rq *rqd,
|
|
|
|
|
bool put_line)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
2018-01-05 21:16:20 +08:00
|
|
|
struct nvm_tgt_dev *dev = pblk->dev;
|
2017-06-27 06:27:13 +08:00
|
|
|
struct pblk_g_ctx *r_ctx = nvm_rq_to_pdu(rqd);
|
2018-06-01 22:41:11 +08:00
|
|
|
struct bio *int_bio = rqd->bio;
|
2018-01-05 21:16:20 +08:00
|
|
|
unsigned long start_time = r_ctx->start_time;
|
|
|
|
|
|
2018-07-18 19:47:39 +08:00
|
|
|
generic_end_io_acct(dev->q, REQ_OP_READ, &pblk->disk->part0, start_time);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
|
|
|
|
if (rqd->error)
|
|
|
|
|
pblk_log_read_err(pblk, rqd);
|
|
|
|
|
|
2018-06-01 21:04:18 +08:00
|
|
|
pblk_read_check_seq(pblk, rqd, r_ctx->lba);
|
2017-10-13 20:46:22 +08:00
|
|
|
|
2018-06-01 22:41:11 +08:00
|
|
|
if (int_bio)
|
|
|
|
|
bio_put(int_bio);
|
2017-06-27 06:27:13 +08:00
|
|
|
|
2017-10-13 20:46:23 +08:00
|
|
|
if (put_line)
|
2018-10-09 19:11:40 +08:00
|
|
|
pblk_rq_to_line_put(pblk, rqd);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
atomic_long_add(rqd->nr_ppas, &pblk->sync_reads);
|
|
|
|
|
atomic_long_sub(rqd->nr_ppas, &pblk->inflight_reads);
|
|
|
|
|
#endif
|
|
|
|
|
|
2017-10-13 20:46:19 +08:00
|
|
|
pblk_free_rqd(pblk, rqd, PBLK_READ);
|
2017-06-26 17:57:29 +08:00
|
|
|
atomic_dec(&pblk->inflight_io);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
2017-10-13 20:46:23 +08:00
|
|
|
static void pblk_end_io_read(struct nvm_rq *rqd)
|
|
|
|
|
{
|
|
|
|
|
struct pblk *pblk = rqd->private;
|
2018-06-01 22:41:11 +08:00
|
|
|
struct pblk_g_ctx *r_ctx = nvm_rq_to_pdu(rqd);
|
|
|
|
|
struct bio *bio = (struct bio *)r_ctx->private;
|
2017-10-13 20:46:23 +08:00
|
|
|
|
2018-06-01 22:41:11 +08:00
|
|
|
pblk_end_user_read(bio);
|
2017-10-13 20:46:23 +08:00
|
|
|
__pblk_end_io_read(pblk, rqd, true);
|
|
|
|
|
}
|
|
|
|
|
|
2018-07-13 16:48:44 +08:00
|
|
|
static void pblk_end_partial_read(struct nvm_rq *rqd)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
2018-07-13 16:48:44 +08:00
|
|
|
struct pblk *pblk = rqd->private;
|
|
|
|
|
struct pblk_g_ctx *r_ctx = nvm_rq_to_pdu(rqd);
|
|
|
|
|
struct pblk_pr_ctx *pr_ctx = r_ctx->private;
|
2018-12-12 03:16:23 +08:00
|
|
|
struct pblk_sec_meta *meta;
|
2018-07-13 16:48:44 +08:00
|
|
|
struct bio *new_bio = rqd->bio;
|
|
|
|
|
struct bio *bio = pr_ctx->orig_bio;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
struct bio_vec src_bv, dst_bv;
|
2018-12-12 03:16:23 +08:00
|
|
|
void *meta_list = rqd->meta_list;
|
2018-07-13 16:48:44 +08:00
|
|
|
int bio_init_idx = pr_ctx->bio_init_idx;
|
|
|
|
|
unsigned long *read_bitmap = pr_ctx->bitmap;
|
|
|
|
|
int nr_secs = pr_ctx->orig_nr_secs;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
int nr_holes = nr_secs - bitmap_weight(read_bitmap, nr_secs);
|
2018-07-13 16:48:44 +08:00
|
|
|
void *src_p, *dst_p;
|
|
|
|
|
int hole, i;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2017-10-13 20:46:24 +08:00
|
|
|
if (unlikely(nr_holes == 1)) {
|
2017-10-13 20:46:23 +08:00
|
|
|
struct ppa_addr ppa;
|
|
|
|
|
|
|
|
|
|
ppa = rqd->ppa_addr;
|
2018-07-13 16:48:44 +08:00
|
|
|
rqd->ppa_list = pr_ctx->ppa_ptr;
|
|
|
|
|
rqd->dma_ppa_list = pr_ctx->dma_ppa_list;
|
2017-10-13 20:46:23 +08:00
|
|
|
rqd->ppa_list[0] = ppa;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
2017-10-13 20:46:22 +08:00
|
|
|
for (i = 0; i < nr_secs; i++) {
|
2018-12-12 03:16:23 +08:00
|
|
|
meta = pblk_get_meta(pblk, meta_list, i);
|
|
|
|
|
pr_ctx->lba_list_media[i] = le64_to_cpu(meta->lba);
|
|
|
|
|
meta->lba = cpu_to_le64(pr_ctx->lba_list_mem[i]);
|
2017-10-13 20:46:22 +08:00
|
|
|
}
|
|
|
|
|
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
/* Fill the holes in the original bio */
|
|
|
|
|
i = 0;
|
|
|
|
|
hole = find_first_zero_bit(read_bitmap, nr_secs);
|
|
|
|
|
do {
|
2018-10-09 19:11:42 +08:00
|
|
|
struct pblk_line *line;
|
2017-10-13 20:46:23 +08:00
|
|
|
|
2018-10-09 19:11:42 +08:00
|
|
|
line = pblk_ppa_to_line(pblk, rqd->ppa_list[i]);
|
2017-10-13 20:46:23 +08:00
|
|
|
kref_put(&line->ref, pblk_line_put);
|
|
|
|
|
|
2018-12-12 03:16:23 +08:00
|
|
|
meta = pblk_get_meta(pblk, meta_list, hole);
|
|
|
|
|
meta->lba = cpu_to_le64(pr_ctx->lba_list_media[i]);
|
2017-10-13 20:46:22 +08:00
|
|
|
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
src_bv = new_bio->bi_io_vec[i++];
|
2018-07-13 16:48:44 +08:00
|
|
|
dst_bv = bio->bi_io_vec[bio_init_idx + hole];
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
|
|
|
|
src_p = kmap_atomic(src_bv.bv_page);
|
|
|
|
|
dst_p = kmap_atomic(dst_bv.bv_page);
|
|
|
|
|
|
|
|
|
|
memcpy(dst_p + dst_bv.bv_offset,
|
|
|
|
|
src_p + src_bv.bv_offset,
|
|
|
|
|
PBLK_EXPOSED_PAGE_SIZE);
|
|
|
|
|
|
|
|
|
|
kunmap_atomic(src_p);
|
|
|
|
|
kunmap_atomic(dst_p);
|
|
|
|
|
|
2018-05-21 06:25:50 +08:00
|
|
|
mempool_free(src_bv.bv_page, &pblk->page_bio_pool);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
|
|
|
|
hole = find_next_zero_bit(read_bitmap, nr_secs, hole + 1);
|
|
|
|
|
} while (hole < nr_secs);
|
|
|
|
|
|
|
|
|
|
bio_put(new_bio);
|
2018-07-13 16:48:44 +08:00
|
|
|
kfree(pr_ctx);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2018-06-01 22:41:11 +08:00
|
|
|
/* restore original request */
|
|
|
|
|
rqd->bio = NULL;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
rqd->nr_ppas = nr_secs;
|
|
|
|
|
|
2018-07-13 16:48:44 +08:00
|
|
|
bio_endio(bio);
|
2017-10-13 20:46:23 +08:00
|
|
|
__pblk_end_io_read(pblk, rqd, false);
|
2018-07-13 16:48:44 +08:00
|
|
|
}
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2018-07-13 16:48:44 +08:00
|
|
|
static int pblk_setup_partial_read(struct pblk *pblk, struct nvm_rq *rqd,
|
|
|
|
|
unsigned int bio_init_idx,
|
|
|
|
|
unsigned long *read_bitmap,
|
|
|
|
|
int nr_holes)
|
|
|
|
|
{
|
2018-12-12 03:16:23 +08:00
|
|
|
void *meta_list = rqd->meta_list;
|
2018-07-13 16:48:44 +08:00
|
|
|
struct pblk_g_ctx *r_ctx = nvm_rq_to_pdu(rqd);
|
|
|
|
|
struct pblk_pr_ctx *pr_ctx;
|
|
|
|
|
struct bio *new_bio, *bio = r_ctx->private;
|
|
|
|
|
int nr_secs = rqd->nr_ppas;
|
|
|
|
|
int i;
|
|
|
|
|
|
|
|
|
|
new_bio = bio_alloc(GFP_KERNEL, nr_holes);
|
|
|
|
|
|
|
|
|
|
if (pblk_bio_add_pages(pblk, new_bio, GFP_KERNEL, nr_holes))
|
|
|
|
|
goto fail_bio_put;
|
|
|
|
|
|
|
|
|
|
if (nr_holes != new_bio->bi_vcnt) {
|
|
|
|
|
WARN_ONCE(1, "pblk: malformed bio\n");
|
|
|
|
|
goto fail_free_pages;
|
|
|
|
|
}
|
|
|
|
|
|
2018-12-12 03:16:22 +08:00
|
|
|
pr_ctx = kzalloc(sizeof(struct pblk_pr_ctx), GFP_KERNEL);
|
2018-07-13 16:48:44 +08:00
|
|
|
if (!pr_ctx)
|
|
|
|
|
goto fail_free_pages;
|
|
|
|
|
|
2018-12-12 03:16:23 +08:00
|
|
|
for (i = 0; i < nr_secs; i++) {
|
|
|
|
|
struct pblk_sec_meta *meta = pblk_get_meta(pblk, meta_list, i);
|
|
|
|
|
|
|
|
|
|
pr_ctx->lba_list_mem[i] = le64_to_cpu(meta->lba);
|
|
|
|
|
}
|
2018-07-13 16:48:44 +08:00
|
|
|
|
|
|
|
|
new_bio->bi_iter.bi_sector = 0; /* internal bio */
|
|
|
|
|
bio_set_op_attrs(new_bio, REQ_OP_READ, 0);
|
|
|
|
|
|
|
|
|
|
rqd->bio = new_bio;
|
|
|
|
|
rqd->nr_ppas = nr_holes;
|
|
|
|
|
|
|
|
|
|
pr_ctx->orig_bio = bio;
|
|
|
|
|
bitmap_copy(pr_ctx->bitmap, read_bitmap, NVM_MAX_VLBA);
|
|
|
|
|
pr_ctx->bio_init_idx = bio_init_idx;
|
|
|
|
|
pr_ctx->orig_nr_secs = nr_secs;
|
|
|
|
|
r_ctx->private = pr_ctx;
|
|
|
|
|
|
|
|
|
|
if (unlikely(nr_holes == 1)) {
|
|
|
|
|
pr_ctx->ppa_ptr = rqd->ppa_list;
|
|
|
|
|
pr_ctx->dma_ppa_list = rqd->dma_ppa_list;
|
|
|
|
|
rqd->ppa_addr = rqd->ppa_list[0];
|
|
|
|
|
}
|
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
|
|
fail_free_pages:
|
2018-06-01 22:41:09 +08:00
|
|
|
pblk_bio_free_pages(pblk, new_bio, 0, new_bio->bi_vcnt);
|
2018-07-13 16:48:44 +08:00
|
|
|
fail_bio_put:
|
|
|
|
|
bio_put(new_bio);
|
|
|
|
|
|
|
|
|
|
return -ENOMEM;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static int pblk_partial_read_bio(struct pblk *pblk, struct nvm_rq *rqd,
|
|
|
|
|
unsigned int bio_init_idx,
|
|
|
|
|
unsigned long *read_bitmap, int nr_secs)
|
|
|
|
|
{
|
|
|
|
|
int nr_holes;
|
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
|
|
nr_holes = nr_secs - bitmap_weight(read_bitmap, nr_secs);
|
|
|
|
|
|
|
|
|
|
if (pblk_setup_partial_read(pblk, rqd, bio_init_idx, read_bitmap,
|
|
|
|
|
nr_holes))
|
|
|
|
|
return NVM_IO_ERR;
|
|
|
|
|
|
|
|
|
|
rqd->end_io = pblk_end_partial_read;
|
|
|
|
|
|
|
|
|
|
ret = pblk_submit_io(pblk, rqd);
|
|
|
|
|
if (ret) {
|
|
|
|
|
bio_put(rqd->bio);
|
|
|
|
|
pblk_err(pblk, "partial read IO submission failed\n");
|
|
|
|
|
goto err;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
return NVM_IO_OK;
|
|
|
|
|
|
|
|
|
|
err:
|
2018-07-13 16:48:42 +08:00
|
|
|
pblk_err(pblk, "failed to perform partial read\n");
|
2018-07-13 16:48:44 +08:00
|
|
|
|
|
|
|
|
/* Free allocated pages in new bio */
|
|
|
|
|
pblk_bio_free_pages(pblk, rqd->bio, 0, rqd->bio->bi_vcnt);
|
2017-10-13 20:46:23 +08:00
|
|
|
__pblk_end_io_read(pblk, rqd, false);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
return NVM_IO_ERR;
|
|
|
|
|
}
|
|
|
|
|
|
2018-06-01 22:41:11 +08:00
|
|
|
static void pblk_read_rq(struct pblk *pblk, struct nvm_rq *rqd, struct bio *bio,
|
2017-10-13 20:46:13 +08:00
|
|
|
sector_t lba, unsigned long *read_bitmap)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
2018-12-12 03:16:23 +08:00
|
|
|
struct pblk_sec_meta *meta = pblk_get_meta(pblk, rqd->meta_list, 0);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
struct ppa_addr ppa;
|
|
|
|
|
|
|
|
|
|
pblk_lookup_l2p_seq(pblk, &ppa, lba, 1);
|
|
|
|
|
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
atomic_long_inc(&pblk->inflight_reads);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
retry:
|
|
|
|
|
if (pblk_ppa_empty(ppa)) {
|
2018-12-12 03:16:23 +08:00
|
|
|
__le64 addr_empty = cpu_to_le64(ADDR_EMPTY);
|
|
|
|
|
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
WARN_ON(test_and_set_bit(0, read_bitmap));
|
2018-12-12 03:16:23 +08:00
|
|
|
meta->lba = addr_empty;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
return;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* Try to read from write buffer. The address is later checked on the
|
|
|
|
|
* write buffer to prevent retrieving overwritten data.
|
|
|
|
|
*/
|
|
|
|
|
if (pblk_addr_in_cache(ppa)) {
|
2017-07-28 21:13:16 +08:00
|
|
|
if (!pblk_read_from_cache(pblk, bio, lba, ppa, 0, 1)) {
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
pblk_lookup_l2p_seq(pblk, &ppa, lba, 1);
|
|
|
|
|
goto retry;
|
|
|
|
|
}
|
2017-10-13 20:46:22 +08:00
|
|
|
|
2017-10-13 20:46:23 +08:00
|
|
|
WARN_ON(test_and_set_bit(0, read_bitmap));
|
2018-12-12 03:16:23 +08:00
|
|
|
meta->lba = cpu_to_le64(lba);
|
2017-10-13 20:46:22 +08:00
|
|
|
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
2017-10-13 20:46:23 +08:00
|
|
|
atomic_long_inc(&pblk->cache_reads);
|
2017-06-26 17:57:13 +08:00
|
|
|
#endif
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
} else {
|
|
|
|
|
rqd->ppa_addr = ppa;
|
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
int pblk_submit_read(struct pblk *pblk, struct bio *bio)
|
|
|
|
|
{
|
|
|
|
|
struct nvm_tgt_dev *dev = pblk->dev;
|
2018-01-05 21:16:20 +08:00
|
|
|
struct request_queue *q = dev->q;
|
2017-10-13 20:46:13 +08:00
|
|
|
sector_t blba = pblk_get_lba(bio);
|
2017-04-22 06:48:40 +08:00
|
|
|
unsigned int nr_secs = pblk_get_secs(bio);
|
2017-10-13 20:46:22 +08:00
|
|
|
struct pblk_g_ctx *r_ctx;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
struct nvm_rq *rqd;
|
|
|
|
|
unsigned int bio_init_idx;
|
2018-07-13 16:48:40 +08:00
|
|
|
DECLARE_BITMAP(read_bitmap, NVM_MAX_VLBA);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
int ret = NVM_IO_ERR;
|
|
|
|
|
|
2018-07-18 19:47:39 +08:00
|
|
|
generic_start_io_acct(q, REQ_OP_READ, bio_sectors(bio),
|
|
|
|
|
&pblk->disk->part0);
|
2018-01-05 21:16:20 +08:00
|
|
|
|
2018-07-13 16:48:40 +08:00
|
|
|
bitmap_zero(read_bitmap, nr_secs);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2017-10-13 20:46:19 +08:00
|
|
|
rqd = pblk_alloc_rqd(pblk, PBLK_READ);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
|
|
|
|
rqd->opcode = NVM_OP_PREAD;
|
|
|
|
|
rqd->nr_ppas = nr_secs;
|
2018-06-01 22:41:11 +08:00
|
|
|
rqd->bio = NULL; /* cloned bio if needed */
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
rqd->private = pblk;
|
|
|
|
|
rqd->end_io = pblk_end_io_read;
|
|
|
|
|
|
2017-10-13 20:46:22 +08:00
|
|
|
r_ctx = nvm_rq_to_pdu(rqd);
|
2018-01-05 21:16:20 +08:00
|
|
|
r_ctx->start_time = jiffies;
|
2017-10-13 20:46:22 +08:00
|
|
|
r_ctx->lba = blba;
|
2018-06-01 22:41:11 +08:00
|
|
|
r_ctx->private = bio; /* original bio */
|
2017-10-13 20:46:22 +08:00
|
|
|
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
/* Save the index for this bio's start. This is needed in case
|
|
|
|
|
* we need to fill a partial read.
|
|
|
|
|
*/
|
|
|
|
|
bio_init_idx = pblk_get_bi_idx(bio);
|
|
|
|
|
|
2018-10-09 19:12:02 +08:00
|
|
|
if (pblk_alloc_rqd_meta(pblk, rqd))
|
2017-06-26 17:57:24 +08:00
|
|
|
goto fail_rqd_free;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2018-10-09 19:12:02 +08:00
|
|
|
if (nr_secs > 1)
|
2018-07-13 16:48:40 +08:00
|
|
|
pblk_read_ppalist_rq(pblk, rqd, bio, blba, read_bitmap);
|
2018-10-09 19:12:02 +08:00
|
|
|
else
|
2018-07-13 16:48:40 +08:00
|
|
|
pblk_read_rq(pblk, rqd, bio, blba, read_bitmap);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2018-07-13 16:48:40 +08:00
|
|
|
if (bitmap_full(read_bitmap, nr_secs)) {
|
2017-06-26 17:57:29 +08:00
|
|
|
atomic_inc(&pblk->inflight_io);
|
2017-10-13 20:46:23 +08:00
|
|
|
__pblk_end_io_read(pblk, rqd, false);
|
2018-06-01 22:41:11 +08:00
|
|
|
return NVM_IO_DONE;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* All sectors are to be read from the device */
|
2018-07-13 16:48:40 +08:00
|
|
|
if (bitmap_empty(read_bitmap, rqd->nr_ppas)) {
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
struct bio *int_bio = NULL;
|
|
|
|
|
|
|
|
|
|
/* Clone read bio to deal with read errors internally */
|
2018-05-21 06:25:50 +08:00
|
|
|
int_bio = bio_clone_fast(bio, GFP_KERNEL, &pblk_bio_set);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
if (!int_bio) {
|
2018-07-13 16:48:42 +08:00
|
|
|
pblk_err(pblk, "could not clone read bio\n");
|
2018-01-05 21:16:20 +08:00
|
|
|
goto fail_end_io;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
rqd->bio = int_bio;
|
|
|
|
|
|
2018-06-01 21:04:21 +08:00
|
|
|
if (pblk_submit_io(pblk, rqd)) {
|
2018-07-13 16:48:42 +08:00
|
|
|
pblk_err(pblk, "read IO submission failed\n");
|
2018-06-01 21:04:21 +08:00
|
|
|
ret = NVM_IO_ERR;
|
2018-01-05 21:16:20 +08:00
|
|
|
goto fail_end_io;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
return NVM_IO_OK;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* The read bio request could be partially filled by the write buffer,
|
|
|
|
|
* but there are some holes that need to be read from the drive.
|
|
|
|
|
*/
|
2018-07-13 16:48:44 +08:00
|
|
|
ret = pblk_partial_read_bio(pblk, rqd, bio_init_idx, read_bitmap,
|
|
|
|
|
nr_secs);
|
|
|
|
|
if (ret)
|
|
|
|
|
goto fail_meta_free;
|
|
|
|
|
|
|
|
|
|
return NVM_IO_OK;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2018-07-13 16:48:44 +08:00
|
|
|
fail_meta_free:
|
|
|
|
|
nvm_dev_dma_free(dev->parent, rqd->meta_list, rqd->dma_meta_list);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
fail_rqd_free:
|
2017-10-13 20:46:19 +08:00
|
|
|
pblk_free_rqd(pblk, rqd, PBLK_READ);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
return ret;
|
2018-01-05 21:16:20 +08:00
|
|
|
fail_end_io:
|
|
|
|
|
__pblk_end_io_read(pblk, rqd, false);
|
|
|
|
|
return ret;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static int read_ppalist_rq_gc(struct pblk *pblk, struct nvm_rq *rqd,
|
|
|
|
|
struct pblk_line *line, u64 *lba_list,
|
2017-10-13 20:46:14 +08:00
|
|
|
u64 *paddr_list_gc, unsigned int nr_secs)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
2018-10-09 19:11:37 +08:00
|
|
|
struct ppa_addr ppa_list_l2p[NVM_MAX_VLBA];
|
2017-10-13 20:46:14 +08:00
|
|
|
struct ppa_addr ppa_gc;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
int valid_secs = 0;
|
|
|
|
|
int i;
|
|
|
|
|
|
2017-10-13 20:46:14 +08:00
|
|
|
pblk_lookup_l2p_rand(pblk, ppa_list_l2p, lba_list, nr_secs);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
|
|
|
|
for (i = 0; i < nr_secs; i++) {
|
2017-10-13 20:46:14 +08:00
|
|
|
if (lba_list[i] == ADDR_EMPTY)
|
|
|
|
|
continue;
|
|
|
|
|
|
|
|
|
|
ppa_gc = addr_to_gen_ppa(pblk, paddr_list_gc[i], line->id);
|
|
|
|
|
if (!pblk_ppa_comp(ppa_list_l2p[i], ppa_gc)) {
|
|
|
|
|
paddr_list_gc[i] = lba_list[i] = ADDR_EMPTY;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
continue;
|
|
|
|
|
}
|
|
|
|
|
|
2017-10-13 20:46:14 +08:00
|
|
|
rqd->ppa_list[valid_secs++] = ppa_list_l2p[i];
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
atomic_long_add(valid_secs, &pblk->inflight_reads);
|
|
|
|
|
#endif
|
2017-10-13 20:46:14 +08:00
|
|
|
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
return valid_secs;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static int read_rq_gc(struct pblk *pblk, struct nvm_rq *rqd,
|
2017-10-13 20:46:14 +08:00
|
|
|
struct pblk_line *line, sector_t lba,
|
|
|
|
|
u64 paddr_gc)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
2017-10-13 20:46:14 +08:00
|
|
|
struct ppa_addr ppa_l2p, ppa_gc;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
int valid_secs = 0;
|
|
|
|
|
|
2017-04-22 06:49:56 +08:00
|
|
|
if (lba == ADDR_EMPTY)
|
|
|
|
|
goto out;
|
|
|
|
|
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
/* logic error: lba out-of-bounds */
|
2017-04-16 02:55:52 +08:00
|
|
|
if (lba >= pblk->rl.nr_secs) {
|
|
|
|
|
WARN(1, "pblk: read lba out of bounds\n");
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
goto out;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
spin_lock(&pblk->trans_lock);
|
2017-10-13 20:46:14 +08:00
|
|
|
ppa_l2p = pblk_trans_map_get(pblk, lba);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
spin_unlock(&pblk->trans_lock);
|
|
|
|
|
|
2017-10-13 20:46:14 +08:00
|
|
|
ppa_gc = addr_to_gen_ppa(pblk, paddr_gc, line->id);
|
|
|
|
|
if (!pblk_ppa_comp(ppa_l2p, ppa_gc))
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
goto out;
|
|
|
|
|
|
2017-10-13 20:46:14 +08:00
|
|
|
rqd->ppa_addr = ppa_l2p;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
valid_secs = 1;
|
|
|
|
|
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
atomic_long_inc(&pblk->inflight_reads);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
out:
|
|
|
|
|
return valid_secs;
|
|
|
|
|
}
|
|
|
|
|
|
2017-10-13 20:46:14 +08:00
|
|
|
int pblk_submit_read_gc(struct pblk *pblk, struct pblk_gc_rq *gc_rq)
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
{
|
|
|
|
|
struct nvm_tgt_dev *dev = pblk->dev;
|
|
|
|
|
struct nvm_geo *geo = &dev->geo;
|
|
|
|
|
struct bio *bio;
|
|
|
|
|
struct nvm_rq rqd;
|
2017-10-13 20:46:14 +08:00
|
|
|
int data_len;
|
|
|
|
|
int ret = NVM_IO_OK;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
|
|
|
|
memset(&rqd, 0, sizeof(struct nvm_rq));
|
|
|
|
|
|
2018-10-09 19:12:02 +08:00
|
|
|
ret = pblk_alloc_rqd_meta(pblk, &rqd);
|
|
|
|
|
if (ret)
|
|
|
|
|
return ret;
|
2017-06-26 17:57:24 +08:00
|
|
|
|
2017-10-13 20:46:14 +08:00
|
|
|
if (gc_rq->nr_secs > 1) {
|
|
|
|
|
gc_rq->secs_to_gc = read_ppalist_rq_gc(pblk, &rqd, gc_rq->line,
|
|
|
|
|
gc_rq->lba_list,
|
|
|
|
|
gc_rq->paddr_list,
|
|
|
|
|
gc_rq->nr_secs);
|
|
|
|
|
if (gc_rq->secs_to_gc == 1)
|
2017-06-26 17:57:24 +08:00
|
|
|
rqd.ppa_addr = rqd.ppa_list[0];
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
} else {
|
2017-10-13 20:46:14 +08:00
|
|
|
gc_rq->secs_to_gc = read_rq_gc(pblk, &rqd, gc_rq->line,
|
|
|
|
|
gc_rq->lba_list[0],
|
|
|
|
|
gc_rq->paddr_list[0]);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
2017-10-13 20:46:14 +08:00
|
|
|
if (!(gc_rq->secs_to_gc))
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
goto out;
|
|
|
|
|
|
2018-03-30 06:05:10 +08:00
|
|
|
data_len = (gc_rq->secs_to_gc) * geo->csecs;
|
2017-10-13 20:46:14 +08:00
|
|
|
bio = pblk_bio_map_addr(pblk, gc_rq->data, gc_rq->secs_to_gc, data_len,
|
2017-10-13 20:46:02 +08:00
|
|
|
PBLK_VMALLOC_META, GFP_KERNEL);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
if (IS_ERR(bio)) {
|
2018-07-13 16:48:42 +08:00
|
|
|
pblk_err(pblk, "could not allocate GC bio (%lu)\n",
|
2018-10-09 19:12:02 +08:00
|
|
|
PTR_ERR(bio));
|
|
|
|
|
ret = PTR_ERR(bio);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
goto err_free_dma;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
bio->bi_iter.bi_sector = 0; /* internal bio */
|
|
|
|
|
bio_set_op_attrs(bio, REQ_OP_READ, 0);
|
|
|
|
|
|
|
|
|
|
rqd.opcode = NVM_OP_PREAD;
|
2017-10-13 20:46:14 +08:00
|
|
|
rqd.nr_ppas = gc_rq->secs_to_gc;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
rqd.bio = bio;
|
|
|
|
|
|
2017-10-13 20:46:47 +08:00
|
|
|
if (pblk_submit_io_sync(pblk, &rqd)) {
|
2017-10-13 20:46:14 +08:00
|
|
|
ret = -EIO;
|
2018-07-13 16:48:42 +08:00
|
|
|
pblk_err(pblk, "GC read request failed\n");
|
2017-10-13 20:46:02 +08:00
|
|
|
goto err_free_bio;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|
|
|
|
|
|
2018-06-01 21:04:18 +08:00
|
|
|
pblk_read_check_rand(pblk, &rqd, gc_rq->lba_list, gc_rq->nr_secs);
|
2018-06-01 21:04:17 +08:00
|
|
|
|
2017-06-26 17:57:29 +08:00
|
|
|
atomic_dec(&pblk->inflight_io);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
|
|
|
|
if (rqd.error) {
|
|
|
|
|
atomic_long_inc(&pblk->read_failed_gc);
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
pblk_print_failed_rqd(pblk, &rqd, rqd.error);
|
|
|
|
|
#endif
|
|
|
|
|
}
|
|
|
|
|
|
2018-07-13 16:48:37 +08:00
|
|
|
#ifdef CONFIG_NVM_PBLK_DEBUG
|
2017-10-13 20:46:14 +08:00
|
|
|
atomic_long_add(gc_rq->secs_to_gc, &pblk->sync_reads);
|
|
|
|
|
atomic_long_add(gc_rq->secs_to_gc, &pblk->recov_gc_reads);
|
|
|
|
|
atomic_long_sub(gc_rq->secs_to_gc, &pblk->inflight_reads);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
out:
|
2018-10-09 19:12:02 +08:00
|
|
|
pblk_free_rqd_meta(pblk, &rqd);
|
2017-10-13 20:46:14 +08:00
|
|
|
return ret;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
|
2017-10-13 20:46:02 +08:00
|
|
|
err_free_bio:
|
|
|
|
|
bio_put(bio);
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
err_free_dma:
|
2018-10-09 19:12:02 +08:00
|
|
|
pblk_free_rqd_meta(pblk, &rqd);
|
2017-10-13 20:46:14 +08:00
|
|
|
return ret;
|
lightnvm: physical block device (pblk) target
This patch introduces pblk, a host-side translation layer for
Open-Channel SSDs to expose them like block devices. The translation
layer allows data placement decisions, and I/O scheduling to be
managed by the host, enabling users to optimize the SSD for their
specific workloads.
An open-channel SSD has a set of LUNs (parallel units) and a
collection of blocks. Each block can be read in any order, but
writes must be sequential. Writes may also fail, and if a block
requires it, must also be reset before new writes can be
applied.
To manage the constraints, pblk maintains a logical to
physical address (L2P) table, write cache, garbage
collection logic, recovery scheme, and logic to rate-limit
user I/Os versus garbage collection I/Os.
The L2P table is fully-associative and manages sectors at a
4KB granularity. Pblk stores the L2P table in two places, in
the out-of-band area of the media and on the last page of a
line. In the cause of a power failure, pblk will perform a
scan to recover the L2P table.
The user data is organized into lines. A line is data
striped across blocks and LUNs. The lines enable the host to
reduce the amount of metadata to maintain besides the user
data and makes it easier to implement RAID or erasure coding
in the future.
pblk implements multi-tenant support and can be instantiated
multiple times on the same drive. Each instance owns a
portion of the SSD - both regarding I/O bandwidth and
capacity - providing I/O isolation for each case.
Finally, pblk also exposes a sysfs interface that allows
user-space to peek into the internals of pblk. The interface
is available at /dev/block/*/pblk/ where * is the block
device name exposed.
This work also contains contributions from:
Matias Bjørling <matias@cnexlabs.com>
Simon A. F. Lund <slund@cnexlabs.com>
Young Tack Jin <youngtack.jin@gmail.com>
Huaicheng Li <huaicheng@cs.uchicago.edu>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-16 02:55:50 +08:00
|
|
|
}
|