iommu: arm-smmu-impl: Add sdm845 implementation hook
Add reset hook for sdm845 based platforms to turn off
the wait-for-safe sequence.
Understanding how wait-for-safe logic affects USB and UFS performance
on MTP845 and DB845 boards:
Qcom's implementation of arm,mmu-500 adds a WAIT-FOR-SAFE logic
to address under-performance issues in real-time clients, such as
Display, and Camera.
On receiving an invalidation requests, the SMMU forwards SAFE request
to these clients and waits for SAFE ack signal from real-time clients.
The SAFE signal from such clients is used to qualify the start of
invalidation.
This logic is controlled by chicken bits, one for each - MDP (display),
IFE0, and IFE1 (camera), that can be accessed only from secure software
on sdm845.
This configuration, however, degrades the performance of non-real time
clients, such as USB, and UFS etc. This happens because, with wait-for-safe
logic enabled the hardware tries to throttle non-real time clients while
waiting for SAFE ack signals from real-time clients.
On mtp845 and db845 devices, with wait-for-safe logic enabled by the
bootloaders we see degraded performance of USB and UFS when kernel
enables the smmu stage-1 translations for these clients.
Turn off this wait-for-safe logic from the kernel gets us back the perf
of USB and UFS devices until we re-visit this when we start seeing perf
issues on display/camera on upstream supported SDM845 platforms.
The bootloaders on these boards implement secure monitor callbacks to
handle a specific command - QCOM_SCM_SVC_SMMU_PROGRAM with which the
logic can be toggled.
There are other boards such as cheza whose bootloaders don't enable this
logic. Such boards don't implement callbacks to handle the specific SCM
call so disabling this logic for such boards will be a no-op.
This change is inspired by the downstream change from Patrick Daly
to address performance issues with display and camera by handling
this wait-for-safe within separte io-pagetable ops to do TLB
maintenance. So a big thanks to him for the change and for all the
offline discussions.
Without this change the UFS reads are pretty slow:
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=10 conv=sync
10+0 records in
10+0 records out
10485760 bytes (10.0MB) copied, 22.394903 seconds, 457.2KB/s
real 0m 22.39s
user 0m 0.00s
sys 0m 0.01s
With this change they are back to rock!
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=300 conv=sync
300+0 records in
300+0 records out
314572800 bytes (300.0MB) copied, 1.030541 seconds, 291.1MB/s
real 0m 1.03s
user 0m 0.00s
sys 0m 0.54s
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Will Deacon <will@kernel.org>
2019-09-20 16:04:29 +08:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
|
/*
|
|
|
|
|
* Copyright (c) 2019, The Linux Foundation. All rights reserved.
|
|
|
|
|
*/
|
|
|
|
|
|
2020-04-21 02:33:51 +08:00
|
|
|
#include <linux/of_device.h>
|
iommu: arm-smmu-impl: Add sdm845 implementation hook
Add reset hook for sdm845 based platforms to turn off
the wait-for-safe sequence.
Understanding how wait-for-safe logic affects USB and UFS performance
on MTP845 and DB845 boards:
Qcom's implementation of arm,mmu-500 adds a WAIT-FOR-SAFE logic
to address under-performance issues in real-time clients, such as
Display, and Camera.
On receiving an invalidation requests, the SMMU forwards SAFE request
to these clients and waits for SAFE ack signal from real-time clients.
The SAFE signal from such clients is used to qualify the start of
invalidation.
This logic is controlled by chicken bits, one for each - MDP (display),
IFE0, and IFE1 (camera), that can be accessed only from secure software
on sdm845.
This configuration, however, degrades the performance of non-real time
clients, such as USB, and UFS etc. This happens because, with wait-for-safe
logic enabled the hardware tries to throttle non-real time clients while
waiting for SAFE ack signals from real-time clients.
On mtp845 and db845 devices, with wait-for-safe logic enabled by the
bootloaders we see degraded performance of USB and UFS when kernel
enables the smmu stage-1 translations for these clients.
Turn off this wait-for-safe logic from the kernel gets us back the perf
of USB and UFS devices until we re-visit this when we start seeing perf
issues on display/camera on upstream supported SDM845 platforms.
The bootloaders on these boards implement secure monitor callbacks to
handle a specific command - QCOM_SCM_SVC_SMMU_PROGRAM with which the
logic can be toggled.
There are other boards such as cheza whose bootloaders don't enable this
logic. Such boards don't implement callbacks to handle the specific SCM
call so disabling this logic for such boards will be a no-op.
This change is inspired by the downstream change from Patrick Daly
to address performance issues with display and camera by handling
this wait-for-safe within separte io-pagetable ops to do TLB
maintenance. So a big thanks to him for the change and for all the
offline discussions.
Without this change the UFS reads are pretty slow:
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=10 conv=sync
10+0 records in
10+0 records out
10485760 bytes (10.0MB) copied, 22.394903 seconds, 457.2KB/s
real 0m 22.39s
user 0m 0.00s
sys 0m 0.01s
With this change they are back to rock!
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=300 conv=sync
300+0 records in
300+0 records out
314572800 bytes (300.0MB) copied, 1.030541 seconds, 291.1MB/s
real 0m 1.03s
user 0m 0.00s
sys 0m 0.54s
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Will Deacon <will@kernel.org>
2019-09-20 16:04:29 +08:00
|
|
|
#include <linux/qcom_scm.h>
|
|
|
|
|
|
|
|
|
|
#include "arm-smmu.h"
|
|
|
|
|
|
|
|
|
|
struct qcom_smmu {
|
|
|
|
|
struct arm_smmu_device smmu;
|
|
|
|
|
};
|
|
|
|
|
|
2020-06-05 04:39:04 +08:00
|
|
|
static const struct of_device_id qcom_smmu_client_of_match[] __maybe_unused = {
|
2020-04-21 02:33:51 +08:00
|
|
|
{ .compatible = "qcom,adreno" },
|
|
|
|
|
{ .compatible = "qcom,mdp4" },
|
|
|
|
|
{ .compatible = "qcom,mdss" },
|
|
|
|
|
{ .compatible = "qcom,sc7180-mdss" },
|
2020-05-12 01:55:32 +08:00
|
|
|
{ .compatible = "qcom,sc7180-mss-pil" },
|
2020-04-21 02:33:51 +08:00
|
|
|
{ .compatible = "qcom,sdm845-mdss" },
|
2020-05-12 01:55:32 +08:00
|
|
|
{ .compatible = "qcom,sdm845-mss-pil" },
|
2020-04-21 02:33:51 +08:00
|
|
|
{ }
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
static int qcom_smmu_def_domain_type(struct device *dev)
|
|
|
|
|
{
|
|
|
|
|
const struct of_device_id *match =
|
|
|
|
|
of_match_device(qcom_smmu_client_of_match, dev);
|
|
|
|
|
|
|
|
|
|
return match ? IOMMU_DOMAIN_IDENTITY : 0;
|
|
|
|
|
}
|
|
|
|
|
|
iommu: arm-smmu-impl: Add sdm845 implementation hook
Add reset hook for sdm845 based platforms to turn off
the wait-for-safe sequence.
Understanding how wait-for-safe logic affects USB and UFS performance
on MTP845 and DB845 boards:
Qcom's implementation of arm,mmu-500 adds a WAIT-FOR-SAFE logic
to address under-performance issues in real-time clients, such as
Display, and Camera.
On receiving an invalidation requests, the SMMU forwards SAFE request
to these clients and waits for SAFE ack signal from real-time clients.
The SAFE signal from such clients is used to qualify the start of
invalidation.
This logic is controlled by chicken bits, one for each - MDP (display),
IFE0, and IFE1 (camera), that can be accessed only from secure software
on sdm845.
This configuration, however, degrades the performance of non-real time
clients, such as USB, and UFS etc. This happens because, with wait-for-safe
logic enabled the hardware tries to throttle non-real time clients while
waiting for SAFE ack signals from real-time clients.
On mtp845 and db845 devices, with wait-for-safe logic enabled by the
bootloaders we see degraded performance of USB and UFS when kernel
enables the smmu stage-1 translations for these clients.
Turn off this wait-for-safe logic from the kernel gets us back the perf
of USB and UFS devices until we re-visit this when we start seeing perf
issues on display/camera on upstream supported SDM845 platforms.
The bootloaders on these boards implement secure monitor callbacks to
handle a specific command - QCOM_SCM_SVC_SMMU_PROGRAM with which the
logic can be toggled.
There are other boards such as cheza whose bootloaders don't enable this
logic. Such boards don't implement callbacks to handle the specific SCM
call so disabling this logic for such boards will be a no-op.
This change is inspired by the downstream change from Patrick Daly
to address performance issues with display and camera by handling
this wait-for-safe within separte io-pagetable ops to do TLB
maintenance. So a big thanks to him for the change and for all the
offline discussions.
Without this change the UFS reads are pretty slow:
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=10 conv=sync
10+0 records in
10+0 records out
10485760 bytes (10.0MB) copied, 22.394903 seconds, 457.2KB/s
real 0m 22.39s
user 0m 0.00s
sys 0m 0.01s
With this change they are back to rock!
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=300 conv=sync
300+0 records in
300+0 records out
314572800 bytes (300.0MB) copied, 1.030541 seconds, 291.1MB/s
real 0m 1.03s
user 0m 0.00s
sys 0m 0.54s
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Will Deacon <will@kernel.org>
2019-09-20 16:04:29 +08:00
|
|
|
static int qcom_sdm845_smmu500_reset(struct arm_smmu_device *smmu)
|
|
|
|
|
{
|
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* To address performance degradation in non-real time clients,
|
|
|
|
|
* such as USB and UFS, turn off wait-for-safe on sdm845 based boards,
|
|
|
|
|
* such as MTP and db845, whose firmwares implement secure monitor
|
|
|
|
|
* call handlers to turn on/off the wait-for-safe logic.
|
|
|
|
|
*/
|
|
|
|
|
ret = qcom_scm_qsmmu500_wait_safe_toggle(0);
|
|
|
|
|
if (ret)
|
|
|
|
|
dev_warn(smmu->dev, "Failed to turn off SAFE logic\n");
|
|
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
|
}
|
|
|
|
|
|
2020-04-21 02:33:49 +08:00
|
|
|
static int qcom_smmu500_reset(struct arm_smmu_device *smmu)
|
|
|
|
|
{
|
|
|
|
|
const struct device_node *np = smmu->dev->of_node;
|
|
|
|
|
|
|
|
|
|
arm_mmu500_reset(smmu);
|
|
|
|
|
|
|
|
|
|
if (of_device_is_compatible(np, "qcom,sdm845-smmu-500"))
|
|
|
|
|
return qcom_sdm845_smmu500_reset(smmu);
|
|
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
|
}
|
|
|
|
|
|
iommu: arm-smmu-impl: Add sdm845 implementation hook
Add reset hook for sdm845 based platforms to turn off
the wait-for-safe sequence.
Understanding how wait-for-safe logic affects USB and UFS performance
on MTP845 and DB845 boards:
Qcom's implementation of arm,mmu-500 adds a WAIT-FOR-SAFE logic
to address under-performance issues in real-time clients, such as
Display, and Camera.
On receiving an invalidation requests, the SMMU forwards SAFE request
to these clients and waits for SAFE ack signal from real-time clients.
The SAFE signal from such clients is used to qualify the start of
invalidation.
This logic is controlled by chicken bits, one for each - MDP (display),
IFE0, and IFE1 (camera), that can be accessed only from secure software
on sdm845.
This configuration, however, degrades the performance of non-real time
clients, such as USB, and UFS etc. This happens because, with wait-for-safe
logic enabled the hardware tries to throttle non-real time clients while
waiting for SAFE ack signals from real-time clients.
On mtp845 and db845 devices, with wait-for-safe logic enabled by the
bootloaders we see degraded performance of USB and UFS when kernel
enables the smmu stage-1 translations for these clients.
Turn off this wait-for-safe logic from the kernel gets us back the perf
of USB and UFS devices until we re-visit this when we start seeing perf
issues on display/camera on upstream supported SDM845 platforms.
The bootloaders on these boards implement secure monitor callbacks to
handle a specific command - QCOM_SCM_SVC_SMMU_PROGRAM with which the
logic can be toggled.
There are other boards such as cheza whose bootloaders don't enable this
logic. Such boards don't implement callbacks to handle the specific SCM
call so disabling this logic for such boards will be a no-op.
This change is inspired by the downstream change from Patrick Daly
to address performance issues with display and camera by handling
this wait-for-safe within separte io-pagetable ops to do TLB
maintenance. So a big thanks to him for the change and for all the
offline discussions.
Without this change the UFS reads are pretty slow:
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=10 conv=sync
10+0 records in
10+0 records out
10485760 bytes (10.0MB) copied, 22.394903 seconds, 457.2KB/s
real 0m 22.39s
user 0m 0.00s
sys 0m 0.01s
With this change they are back to rock!
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=300 conv=sync
300+0 records in
300+0 records out
314572800 bytes (300.0MB) copied, 1.030541 seconds, 291.1MB/s
real 0m 1.03s
user 0m 0.00s
sys 0m 0.54s
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Will Deacon <will@kernel.org>
2019-09-20 16:04:29 +08:00
|
|
|
static const struct arm_smmu_impl qcom_smmu_impl = {
|
2020-04-21 02:33:51 +08:00
|
|
|
.def_domain_type = qcom_smmu_def_domain_type,
|
2020-04-21 02:33:49 +08:00
|
|
|
.reset = qcom_smmu500_reset,
|
iommu: arm-smmu-impl: Add sdm845 implementation hook
Add reset hook for sdm845 based platforms to turn off
the wait-for-safe sequence.
Understanding how wait-for-safe logic affects USB and UFS performance
on MTP845 and DB845 boards:
Qcom's implementation of arm,mmu-500 adds a WAIT-FOR-SAFE logic
to address under-performance issues in real-time clients, such as
Display, and Camera.
On receiving an invalidation requests, the SMMU forwards SAFE request
to these clients and waits for SAFE ack signal from real-time clients.
The SAFE signal from such clients is used to qualify the start of
invalidation.
This logic is controlled by chicken bits, one for each - MDP (display),
IFE0, and IFE1 (camera), that can be accessed only from secure software
on sdm845.
This configuration, however, degrades the performance of non-real time
clients, such as USB, and UFS etc. This happens because, with wait-for-safe
logic enabled the hardware tries to throttle non-real time clients while
waiting for SAFE ack signals from real-time clients.
On mtp845 and db845 devices, with wait-for-safe logic enabled by the
bootloaders we see degraded performance of USB and UFS when kernel
enables the smmu stage-1 translations for these clients.
Turn off this wait-for-safe logic from the kernel gets us back the perf
of USB and UFS devices until we re-visit this when we start seeing perf
issues on display/camera on upstream supported SDM845 platforms.
The bootloaders on these boards implement secure monitor callbacks to
handle a specific command - QCOM_SCM_SVC_SMMU_PROGRAM with which the
logic can be toggled.
There are other boards such as cheza whose bootloaders don't enable this
logic. Such boards don't implement callbacks to handle the specific SCM
call so disabling this logic for such boards will be a no-op.
This change is inspired by the downstream change from Patrick Daly
to address performance issues with display and camera by handling
this wait-for-safe within separte io-pagetable ops to do TLB
maintenance. So a big thanks to him for the change and for all the
offline discussions.
Without this change the UFS reads are pretty slow:
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=10 conv=sync
10+0 records in
10+0 records out
10485760 bytes (10.0MB) copied, 22.394903 seconds, 457.2KB/s
real 0m 22.39s
user 0m 0.00s
sys 0m 0.01s
With this change they are back to rock!
$ time dd if=/dev/sda of=/dev/zero bs=1048576 count=300 conv=sync
300+0 records in
300+0 records out
314572800 bytes (300.0MB) copied, 1.030541 seconds, 291.1MB/s
real 0m 1.03s
user 0m 0.00s
sys 0m 0.54s
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Will Deacon <will@kernel.org>
2019-09-20 16:04:29 +08:00
|
|
|
};
|
|
|
|
|
|
|
|
|
|
struct arm_smmu_device *qcom_smmu_impl_init(struct arm_smmu_device *smmu)
|
|
|
|
|
{
|
|
|
|
|
struct qcom_smmu *qsmmu;
|
|
|
|
|
|
|
|
|
|
qsmmu = devm_kzalloc(smmu->dev, sizeof(*qsmmu), GFP_KERNEL);
|
|
|
|
|
if (!qsmmu)
|
|
|
|
|
return ERR_PTR(-ENOMEM);
|
|
|
|
|
|
|
|
|
|
qsmmu->smmu = *smmu;
|
|
|
|
|
|
|
|
|
|
qsmmu->smmu.impl = &qcom_smmu_impl;
|
|
|
|
|
devm_kfree(smmu->dev, smmu);
|
|
|
|
|
|
|
|
|
|
return &qsmmu->smmu;
|
|
|
|
|
}
|