UbiquitousOS
/
OpenCloudOS-Kernel
mirror of https://gitee.com/OpenCloudOS/OpenCloudOS-Kernel.git
11
0
Fork 0
Code Issues Projects Releases Wiki Activity
OpenCloudOS-Kernel/arch/arm/boot/dts/bcm2835-rpi-b.dts

18 lines
232 B
Plaintext
Raw Normal View History

ARM: add infra-structure for BCM2835 and Raspberry Pi The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic support for this SoC. http://www.broadcom.com/products/BCM2835 http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Note that the documentation in the latter .pdf assumes the MMU setup that's used on the "VideoCore" companion processor, and does not document physical peripheral addresses. Subtract 0x5e000000 to obtain the physical addresses. This is accounted for by the ranges property in the /soc node in the device tree. The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a minimal device tree for this board; enough to see some very early kernel boot messages through earlyprintk. However, this patch does not yet provide a useful booting system. http://www.raspberrypi.org/. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split from 3-4 months ago, and significantly stripped down and modified since. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Dom Cobley <popcornmix@gmail.com> Signed-off-by: Dom Cobley <dc4@broadcom.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de>
2012-05-26 15:04:43 +08:00
/dts-v1/;
ARM: bcm2835: dt: Use pinctrl header This patch converts all bcm2835 dts and dtsi files to use the pinctrl header file. Reviewed-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-01-30 02:10:50 +08:00
#include "bcm2835-rpi.dtsi"
ARM: add infra-structure for BCM2835 and Raspberry Pi The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic support for this SoC. http://www.broadcom.com/products/BCM2835 http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Note that the documentation in the latter .pdf assumes the MMU setup that's used on the "VideoCore" companion processor, and does not document physical peripheral addresses. Subtract 0x5e000000 to obtain the physical addresses. This is accounted for by the ranges property in the /soc node in the device tree. The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a minimal device tree for this board; enough to see some very early kernel boot messages through earlyprintk. However, this patch does not yet provide a useful booting system. http://www.raspberrypi.org/. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split from 3-4 months ago, and significantly stripped down and modified since. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Dom Cobley <popcornmix@gmail.com> Signed-off-by: Dom Cobley <dc4@broadcom.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de>
2012-05-26 15:04:43 +08:00
/ {
compatible = "raspberrypi,model-b", "brcm,bcm2835";
model = "Raspberry Pi Model B";
ARM: bcm2835: Add Raspberry Pi's ACT LED to DT The Raspberry Pi board has one GPIO-controlled LED labeled "ACT". Add it to the DT via the gpio-leds driver, so users can control it from userspace. If CONFIG_LEDS_TRIGGER_HEARTBEAT is set, the LED will also signal some sign of life. The GPIO circuitry is low-active. And as the bootloader may decide to switch the LED on at boot time, the default state is 'keep'. Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2013-04-29 04:49:52 +08:00
leds {
act {
gpios = <&gpio 16 1>;
};
};
ARM: add infra-structure for BCM2835 and Raspberry Pi The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic support for this SoC. http://www.broadcom.com/products/BCM2835 http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Note that the documentation in the latter .pdf assumes the MMU setup that's used on the "VideoCore" companion processor, and does not document physical peripheral addresses. Subtract 0x5e000000 to obtain the physical addresses. This is accounted for by the ranges property in the /soc node in the device tree. The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a minimal device tree for this board; enough to see some very early kernel boot messages through earlyprintk. However, this patch does not yet provide a useful booting system. http://www.raspberrypi.org/. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split from 3-4 months ago, and significantly stripped down and modified since. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Dom Cobley <popcornmix@gmail.com> Signed-off-by: Dom Cobley <dc4@broadcom.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de>
2012-05-26 15:04:43 +08:00
};
ARM: bcm2835: enable GPIO/pinctrl Enable GPIO and pinctrl in Kconfig. Add required <mach/gpio.h> for gpiolib. Instantiate the BCM2835 GPIO module in bcm2835.dtsi. Add a pinctrl definition to bcm2835-rpi-b.dts that sets up all of the board's required pinmux configuration. GPIO aren't specified; that's left to gpio_request(). Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 11:54:21 +08:00
&gpio {
ARM: bcm2835: dt: Raspberry Pi Model B had no I2S It's the Model B rev2 that had it. Remove it. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: Eric Anholt <eric@anholt.net>
2015-10-12 03:37:15 +08:00
pinctrl-0 = <&gpioout &alt0 &alt3>;
ARM: bcm2835: enable GPIO/pinctrl Enable GPIO and pinctrl in Kconfig. Add required <mach/gpio.h> for gpiolib. Instantiate the BCM2835 GPIO module in bcm2835.dtsi. Add a pinctrl definition to bcm2835-rpi-b.dts that sets up all of the board's required pinmux configuration. GPIO aren't specified; that's left to gpio_request(). Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 11:54:21 +08:00
};