UbiquitousOS
/
OpenCloudOS-Kernel
mirror of https://gitee.com/OpenCloudOS/OpenCloudOS-Kernel.git
11
0
Fork 0
Code Issues Projects Releases Wiki Activity
OpenCloudOS-Kernel/drivers/net/can/c_can/Kconfig

24 lines
749 B
Plaintext
Raw Normal View History

can: c_can: Added support for Bosch C_CAN controller Bosch C_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf This patch adds the support for this controller. The following are the design choices made while writing the controller driver: 1. Interface Register set IF1 has be used only in the current design. 2. Out of the 32 Message objects available, 16 are kept aside for RX purposes and the rest for TX purposes. 3. NAPI implementation is such that both the TX and RX paths function in polling mode. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-14 14:51:44 +08:00
menuconfig CAN_C_CAN
can: c_can: Add support for Bosch D_CAN controller This patch adds the support for D_CAN controller driver to the existing C_CAN driver. Bosch D_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ ipmodules_1/can/d_can_users_manual_111.pdf A new array is added for accessing the d_can registers, according to d_can controller register space. Current D_CAN implementation has following limitations, this is done to avoid large changes to the C_CAN driver. 1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP supports upto 32 message objects but in case of D_CAN we can configure upto 128 message objects. 2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers. 3. These patches have been tested on little endian machine, there might be some hidden endian-related issues due to the nature of the accesses (32-bit registers accessed as 2 16-bit registers). However, I do not have a big-endian D_CAN implementation to confirm. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-05-29 13:43:16 +08:00
tristate "Bosch C_CAN/D_CAN devices"
can: Kconfig: convert 'depends on CAN_DEV' into 'if CAN_DEV...endif' block This patch adds an 'if CAN_DEV...endif' Block around the CAN driver symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies can be removed. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-07-21 03:04:13 +08:00
depends on HAS_IOMEM
can: c_can: Added support for Bosch C_CAN controller Bosch C_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf This patch adds the support for this controller. The following are the design choices made while writing the controller driver: 1. Interface Register set IF1 has be used only in the current design. 2. Out of the 32 Message objects available, 16 are kept aside for RX purposes and the rest for TX purposes. 3. NAPI implementation is such that both the TX and RX paths function in polling mode. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-14 14:51:44 +08:00
if CAN_C_CAN
config CAN_C_CAN_PLATFORM
can: c_can: Add support for Bosch D_CAN controller This patch adds the support for D_CAN controller driver to the existing C_CAN driver. Bosch D_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ ipmodules_1/can/d_can_users_manual_111.pdf A new array is added for accessing the d_can registers, according to d_can controller register space. Current D_CAN implementation has following limitations, this is done to avoid large changes to the C_CAN driver. 1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP supports upto 32 message objects but in case of D_CAN we can configure upto 128 message objects. 2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers. 3. These patches have been tested on little endian machine, there might be some hidden endian-related issues due to the nature of the accesses (32-bit registers accessed as 2 16-bit registers). However, I do not have a big-endian D_CAN implementation to confirm. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-05-29 13:43:16 +08:00
tristate "Generic Platform Bus based C_CAN/D_CAN driver"
can: c_can: Added support for Bosch C_CAN controller Bosch C_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf This patch adds the support for this controller. The following are the design choices made while writing the controller driver: 1. Interface Register set IF1 has be used only in the current design. 2. Out of the 32 Message objects available, 16 are kept aside for RX purposes and the rest for TX purposes. 3. NAPI implementation is such that both the TX and RX paths function in polling mode. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-14 14:51:44 +08:00
---help---
can: c_can: Add support for Bosch D_CAN controller This patch adds the support for D_CAN controller driver to the existing C_CAN driver. Bosch D_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ ipmodules_1/can/d_can_users_manual_111.pdf A new array is added for accessing the d_can registers, according to d_can controller register space. Current D_CAN implementation has following limitations, this is done to avoid large changes to the C_CAN driver. 1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP supports upto 32 message objects but in case of D_CAN we can configure upto 128 message objects. 2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers. 3. These patches have been tested on little endian machine, there might be some hidden endian-related issues due to the nature of the accesses (32-bit registers accessed as 2 16-bit registers). However, I do not have a big-endian D_CAN implementation to confirm. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-05-29 13:43:16 +08:00
This driver adds support for the C_CAN/D_CAN chips connected
to the "platform bus" (Linux abstraction for directly to the
can: c_can: Added support for Bosch C_CAN controller Bosch C_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf This patch adds the support for this controller. The following are the design choices made while writing the controller driver: 1. Interface Register set IF1 has be used only in the current design. 2. Out of the 32 Message objects available, 16 are kept aside for RX purposes and the rest for TX purposes. 3. NAPI implementation is such that both the TX and RX paths function in polling mode. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-14 14:51:44 +08:00
processor attached devices) which can be found on various
can: c_can: Add support for Bosch D_CAN controller This patch adds the support for D_CAN controller driver to the existing C_CAN driver. Bosch D_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ ipmodules_1/can/d_can_users_manual_111.pdf A new array is added for accessing the d_can registers, according to d_can controller register space. Current D_CAN implementation has following limitations, this is done to avoid large changes to the C_CAN driver. 1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP supports upto 32 message objects but in case of D_CAN we can configure upto 128 message objects. 2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers. 3. These patches have been tested on little endian machine, there might be some hidden endian-related issues due to the nature of the accesses (32-bit registers accessed as 2 16-bit registers). However, I do not have a big-endian D_CAN implementation to confirm. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-05-29 13:43:16 +08:00
boards from ST Microelectronics (http://www.st.com) like the
SPEAr1310 and SPEAr320 evaluation boards & TI (www.ti.com)
boards like am335x, dm814x, dm813x and dm811x.
c_can_pci: generic module for C_CAN/D_CAN on PCI Signed-off-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com> Cc: Alan Cox <alan@linux.intel.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Bhupesh Sharma <bhupesh.sharma@st.com> [mkl: fix call to pci_iounmap] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-14 19:43:42 +08:00
config CAN_C_CAN_PCI
tristate "Generic PCI Bus based C_CAN/D_CAN driver"
depends on PCI
---help---
This driver adds support for the C_CAN/D_CAN chips connected
to the PCI bus.
can: c_can: Added support for Bosch C_CAN controller Bosch C_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf This patch adds the support for this controller. The following are the design choices made while writing the controller driver: 1. Interface Register set IF1 has be used only in the current design. 2. Out of the 32 Message objects available, 16 are kept aside for RX purposes and the rest for TX purposes. 3. NAPI implementation is such that both the TX and RX paths function in polling mode. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-14 14:51:44 +08:00
endif