UbiquitousOS
/
OpenCloudOS-Kernel
mirror of https://gitee.com/OpenCloudOS/OpenCloudOS-Kernel.git
11
0
Fork 0
Code Issues Projects Releases Wiki Activity
OpenCloudOS-Kernel/drivers/pinctrl/pinconf.c

591 lines
14 KiB
C
Raw Normal View History

pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
/*
* Core driver for the pin config portions of the pin control subsystem
*
* Copyright (C) 2011 ST-Ericsson SA
* Written on behalf of Linaro for ST-Ericsson
*
* Author: Linus Walleij <linus.walleij@linaro.org>
*
* License terms: GNU General Public License (GPL) version 2
*/
#define pr_fmt(fmt) "pinconfig core: " fmt
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/slab.h>
#include <linux/debugfs.h>
#include <linux/seq_file.h>
#include <linux/pinctrl/machine.h>
#include <linux/pinctrl/pinctrl.h>
#include <linux/pinctrl/pinconf.h>
#include "core.h"
#include "pinconf.h"
pinctrl: Re-order pinconf.[ch] to match each-other Modify the two files so that the order of function prototypes in the header matches the order of implementations in the .c file. Don't prototype a couple of internal functions. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-20 14:45:46 +08:00
int pinconf_check_ops(struct pinctrl_dev *pctldev)
{
const struct pinconf_ops *ops = pctldev->desc->confops;
/* We must be able to read out pin status */
pinctrl: enhance reporting of errors when loading from DT There are a few places in the api where the code simply returns -EINVAL when it finds an error. An example is pinmux_map_to_setting() which now reports an error if we try to match a group with a function that it does not support. The reporting of errors in pinconf_check_ops and pinmux_check_ops now has the same style and is located inside the according functions and not the calling code. When the map is found in the DT but the default state can not be selected we get an error to know that the code at least tried. The patch also removes a stray word from one comment and a "->" from another for the sake of consistency. Finally we replace a few pr_err/debug() calls with dev_err/dbg(). Thanks go to Stephen Warren for reviewing the patch and enhancing the reporting inside pinmux_map_to_setting(). Signed-off-by: John Crispin <blogic@openwrt.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-26 22:47:11 +08:00
if (!ops->pin_config_get && !ops->pin_config_group_get) {
dev_err(pctldev->dev,
"pinconf must be able to read out pin status\n");
pinctrl: Re-order pinconf.[ch] to match each-other Modify the two files so that the order of function prototypes in the header matches the order of implementations in the .c file. Don't prototype a couple of internal functions. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-20 14:45:46 +08:00
return -EINVAL;
pinctrl: enhance reporting of errors when loading from DT There are a few places in the api where the code simply returns -EINVAL when it finds an error. An example is pinmux_map_to_setting() which now reports an error if we try to match a group with a function that it does not support. The reporting of errors in pinconf_check_ops and pinmux_check_ops now has the same style and is located inside the according functions and not the calling code. When the map is found in the DT but the default state can not be selected we get an error to know that the code at least tried. The patch also removes a stray word from one comment and a "->" from another for the sake of consistency. Finally we replace a few pr_err/debug() calls with dev_err/dbg(). Thanks go to Stephen Warren for reviewing the patch and enhancing the reporting inside pinmux_map_to_setting(). Signed-off-by: John Crispin <blogic@openwrt.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-26 22:47:11 +08:00
}
pinctrl: Re-order pinconf.[ch] to match each-other Modify the two files so that the order of function prototypes in the header matches the order of implementations in the .c file. Don't prototype a couple of internal functions. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-20 14:45:46 +08:00
/* We have to be able to config the pins in SOME way */
pinctrl: enhance reporting of errors when loading from DT There are a few places in the api where the code simply returns -EINVAL when it finds an error. An example is pinmux_map_to_setting() which now reports an error if we try to match a group with a function that it does not support. The reporting of errors in pinconf_check_ops and pinmux_check_ops now has the same style and is located inside the according functions and not the calling code. When the map is found in the DT but the default state can not be selected we get an error to know that the code at least tried. The patch also removes a stray word from one comment and a "->" from another for the sake of consistency. Finally we replace a few pr_err/debug() calls with dev_err/dbg(). Thanks go to Stephen Warren for reviewing the patch and enhancing the reporting inside pinmux_map_to_setting(). Signed-off-by: John Crispin <blogic@openwrt.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-26 22:47:11 +08:00
if (!ops->pin_config_set && !ops->pin_config_group_set) {
dev_err(pctldev->dev,
"pinconf has to be able to set a pins config\n");
pinctrl: Re-order pinconf.[ch] to match each-other Modify the two files so that the order of function prototypes in the header matches the order of implementations in the .c file. Don't prototype a couple of internal functions. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-20 14:45:46 +08:00
return -EINVAL;
pinctrl: enhance reporting of errors when loading from DT There are a few places in the api where the code simply returns -EINVAL when it finds an error. An example is pinmux_map_to_setting() which now reports an error if we try to match a group with a function that it does not support. The reporting of errors in pinconf_check_ops and pinmux_check_ops now has the same style and is located inside the according functions and not the calling code. When the map is found in the DT but the default state can not be selected we get an error to know that the code at least tried. The patch also removes a stray word from one comment and a "->" from another for the sake of consistency. Finally we replace a few pr_err/debug() calls with dev_err/dbg(). Thanks go to Stephen Warren for reviewing the patch and enhancing the reporting inside pinmux_map_to_setting(). Signed-off-by: John Crispin <blogic@openwrt.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-26 22:47:11 +08:00
}
pinctrl: Re-order pinconf.[ch] to match each-other Modify the two files so that the order of function prototypes in the header matches the order of implementations in the .c file. Don't prototype a couple of internal functions. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-20 14:45:46 +08:00
return 0;
}
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
int pinconf_validate_map(struct pinctrl_map const *map, int i)
{
if (!map->data.configs.group_or_pin) {
pr_err("failed to register map %s (%d): no group/pin given\n",
map->name, i);
return -EINVAL;
}
if (map->data.configs.num_configs &&
!map->data.configs.configs) {
pr_err("failed to register map %s (%d): no configs ptr given\n",
map->name, i);
return -EINVAL;
}
return 0;
}
pinctrl: introduce generic pin config This is a split-off from the earlier patch set which adds generic pin configuration for the pin controllers that want it. Since we may have a system with mixed generic and custom pin controllers, we pass a boolean in the pin controller ops vtable to indicate if it is generic. ChangeLog v1->v5: - Follow parent patch versioning number system. - Document the semantic meaning of return values from pin config get functions, so we can iterate over pins and check their properties from debugfs as part of the generic config code. - Use proper cast functions in the generic debugfs pin config file. - Expand generic config to optionally cover groups too. ChangeLog v5->v6: - Update to match underlying changes. ChangeLog v6->v7: - Drop DRIVE_OFF parameter, use bias high impedance for this - Delete argument for drive modes push-pull, od and os. These are now just state transitions. - Delete slew rate rising/falling due to discussions on on proper semantics - Drop config wakeup, struct irq_chip does this for now, add back if need be. - Set PIN_CONFIG_END to 0x7fff making room for custom config parameters from 0x8000 and up. - Prefix accessor functions with pinconf_
2011-11-25 01:27:15 +08:00
int pin_config_get_for_pin(struct pinctrl_dev *pctldev, unsigned pin,
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
unsigned long *config)
{
const struct pinconf_ops *ops = pctldev->desc->confops;
if (!ops || !ops->pin_config_get) {
pinctrl: don't create a device for each pin controller Pin controllers should already be instantiated as a device, so there's no need for the pinctrl core to create a new struct device for each controller. This allows the controller's real name to be used in the mux mapping table, rather than e.g. "pinctrl.0", "pinctrl.1", etc. This necessitates removal of the PINMUX_MAP_PRIMARY*() macros, since their sole purpose was to hard-code the .ctrl_dev_name field to be "pinctrl.0". Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-10 07:59:05 +08:00
dev_err(pctldev->dev, "cannot get pin configuration, missing "
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
"pin_config_get() function in driver\n");
return -EINVAL;
}
return ops->pin_config_get(pctldev, pin, config);
}
/**
* pin_config_get() - get the configuration of a single pin parameter
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
* @dev_name: name of the pin controller device for this pin
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
* @name: name of the pin to get the config for
* @config: the config pointed to by this argument will be filled in with the
* current pin state, it can be used directly by drivers as a numeral, or
* it can be dereferenced to any struct.
*/
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
int pin_config_get(const char *dev_name, const char *name,
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
unsigned long *config)
{
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
struct pinctrl_dev *pctldev;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
int pin;
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
mutex_lock(&pinctrl_mutex);
pinctrl: delete raw device pointers in pinmux maps After discussion with Mark Brown in an unrelated thread about ADC lookups, it came to my knowledge that the ability to pass a struct device * in the regulator consumers is just a historical artifact, and not really recommended. Since there are no in-kernel users of these pointers, we just kill them right now, before someone starts to use them. Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-02 01:02:47 +08:00
pctldev = get_pinctrl_dev_from_devname(dev_name);
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (!pctldev) {
pin = -EINVAL;
goto unlock;
}
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pin = pin_get_from_name(pctldev, name);
if (pin < 0)
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
goto unlock;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
pin = pin_config_get_for_pin(pctldev, pin, config);
unlock:
mutex_unlock(&pinctrl_mutex);
return pin;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
EXPORT_SYMBOL(pin_config_get);
pinctrl: Re-order pinconf.[ch] to match each-other Modify the two files so that the order of function prototypes in the header matches the order of implementations in the .c file. Don't prototype a couple of internal functions. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-20 14:45:46 +08:00
static int pin_config_set_for_pin(struct pinctrl_dev *pctldev, unsigned pin,
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
unsigned long config)
{
const struct pinconf_ops *ops = pctldev->desc->confops;
int ret;
if (!ops || !ops->pin_config_set) {
pinctrl: don't create a device for each pin controller Pin controllers should already be instantiated as a device, so there's no need for the pinctrl core to create a new struct device for each controller. This allows the controller's real name to be used in the mux mapping table, rather than e.g. "pinctrl.0", "pinctrl.1", etc. This necessitates removal of the PINMUX_MAP_PRIMARY*() macros, since their sole purpose was to hard-code the .ctrl_dev_name field to be "pinctrl.0". Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-10 07:59:05 +08:00
dev_err(pctldev->dev, "cannot configure pin, missing "
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
"config function in driver\n");
return -EINVAL;
}
ret = ops->pin_config_set(pctldev, pin, config);
if (ret) {
pinctrl: don't create a device for each pin controller Pin controllers should already be instantiated as a device, so there's no need for the pinctrl core to create a new struct device for each controller. This allows the controller's real name to be used in the mux mapping table, rather than e.g. "pinctrl.0", "pinctrl.1", etc. This necessitates removal of the PINMUX_MAP_PRIMARY*() macros, since their sole purpose was to hard-code the .ctrl_dev_name field to be "pinctrl.0". Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-10 07:59:05 +08:00
dev_err(pctldev->dev,
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
"unable to set pin configuration on pin %d\n", pin);
return ret;
}
return 0;
}
/**
* pin_config_set() - set the configuration of a single pin parameter
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
* @dev_name: name of pin controller device for this pin
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
* @name: name of the pin to set the config for
* @config: the config in this argument will contain the desired pin state, it
* can be used directly by drivers as a numeral, or it can be dereferenced
* to any struct.
*/
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
int pin_config_set(const char *dev_name, const char *name,
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
unsigned long config)
{
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
struct pinctrl_dev *pctldev;
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
int pin, ret;
mutex_lock(&pinctrl_mutex);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: delete raw device pointers in pinmux maps After discussion with Mark Brown in an unrelated thread about ADC lookups, it came to my knowledge that the ability to pass a struct device * in the regulator consumers is just a historical artifact, and not really recommended. Since there are no in-kernel users of these pointers, we just kill them right now, before someone starts to use them. Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-02 01:02:47 +08:00
pctldev = get_pinctrl_dev_from_devname(dev_name);
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (!pctldev) {
ret = -EINVAL;
goto unlock;
}
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pin = pin_get_from_name(pctldev, name);
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (pin < 0) {
ret = pin;
goto unlock;
}
ret = pin_config_set_for_pin(pctldev, pin, config);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
unlock:
mutex_unlock(&pinctrl_mutex);
return ret;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
EXPORT_SYMBOL(pin_config_set);
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
int pin_config_group_get(const char *dev_name, const char *pin_group,
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
unsigned long *config)
{
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
struct pinctrl_dev *pctldev;
const struct pinconf_ops *ops;
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
int selector, ret;
mutex_lock(&pinctrl_mutex);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: delete raw device pointers in pinmux maps After discussion with Mark Brown in an unrelated thread about ADC lookups, it came to my knowledge that the ability to pass a struct device * in the regulator consumers is just a historical artifact, and not really recommended. Since there are no in-kernel users of these pointers, we just kill them right now, before someone starts to use them. Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-02 01:02:47 +08:00
pctldev = get_pinctrl_dev_from_devname(dev_name);
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (!pctldev) {
ret = -EINVAL;
goto unlock;
}
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
ops = pctldev->desc->confops;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
if (!ops || !ops->pin_config_group_get) {
pinctrl: don't create a device for each pin controller Pin controllers should already be instantiated as a device, so there's no need for the pinctrl core to create a new struct device for each controller. This allows the controller's real name to be used in the mux mapping table, rather than e.g. "pinctrl.0", "pinctrl.1", etc. This necessitates removal of the PINMUX_MAP_PRIMARY*() macros, since their sole purpose was to hard-code the .ctrl_dev_name field to be "pinctrl.0". Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-10 07:59:05 +08:00
dev_err(pctldev->dev, "cannot get configuration for pin "
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
"group, missing group config get function in "
"driver\n");
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
ret = -EINVAL;
goto unlock;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
selector = pinctrl_get_group_selector(pctldev, pin_group);
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (selector < 0) {
ret = selector;
goto unlock;
}
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
ret = ops->pin_config_group_get(pctldev, selector, config);
unlock:
mutex_unlock(&pinctrl_mutex);
return ret;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
EXPORT_SYMBOL(pin_config_group_get);
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
int pin_config_group_set(const char *dev_name, const char *pin_group,
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
unsigned long config)
{
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
struct pinctrl_dev *pctldev;
const struct pinconf_ops *ops;
const struct pinctrl_ops *pctlops;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
int selector;
const unsigned *pins;
unsigned num_pins;
int ret;
int i;
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
mutex_lock(&pinctrl_mutex);
pinctrl: delete raw device pointers in pinmux maps After discussion with Mark Brown in an unrelated thread about ADC lookups, it came to my knowledge that the ability to pass a struct device * in the regulator consumers is just a historical artifact, and not really recommended. Since there are no in-kernel users of these pointers, we just kill them right now, before someone starts to use them. Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-02 01:02:47 +08:00
pctldev = get_pinctrl_dev_from_devname(dev_name);
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (!pctldev) {
ret = -EINVAL;
goto unlock;
}
pinctrl: pass name instead of device to pin_config_* Obtaining a "struct pinctrl_dev *" is difficult for code not directly related to the pinctrl subsystem. However, the device name of the pinctrl device is fairly well known. So, modify pin_config_*() to take the device name instead of the "struct pinctrl_dev *". Signed-off-by: Stephen Warren <swarren@nvidia.com> [rebased on top of refactoring code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-16 07:57:17 +08:00
ops = pctldev->desc->confops;
pctlops = pctldev->desc->pctlops;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
if (!ops || (!ops->pin_config_group_set && !ops->pin_config_set)) {
pinctrl: don't create a device for each pin controller Pin controllers should already be instantiated as a device, so there's no need for the pinctrl core to create a new struct device for each controller. This allows the controller's real name to be used in the mux mapping table, rather than e.g. "pinctrl.0", "pinctrl.1", etc. This necessitates removal of the PINMUX_MAP_PRIMARY*() macros, since their sole purpose was to hard-code the .ctrl_dev_name field to be "pinctrl.0". Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-10 07:59:05 +08:00
dev_err(pctldev->dev, "cannot configure pin group, missing "
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
"config function in driver\n");
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
ret = -EINVAL;
goto unlock;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
selector = pinctrl_get_group_selector(pctldev, pin_group);
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (selector < 0) {
ret = selector;
goto unlock;
}
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
ret = pctlops->get_group_pins(pctldev, selector, &pins, &num_pins);
if (ret) {
pinctrl: don't create a device for each pin controller Pin controllers should already be instantiated as a device, so there's no need for the pinctrl core to create a new struct device for each controller. This allows the controller's real name to be used in the mux mapping table, rather than e.g. "pinctrl.0", "pinctrl.1", etc. This necessitates removal of the PINMUX_MAP_PRIMARY*() macros, since their sole purpose was to hard-code the .ctrl_dev_name field to be "pinctrl.0". Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-10 07:59:05 +08:00
dev_err(pctldev->dev, "cannot configure pin group, error "
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
"getting pins\n");
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
goto unlock;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
/*
* If the pin controller supports handling entire groups we use that
* capability.
*/
if (ops->pin_config_group_set) {
ret = ops->pin_config_group_set(pctldev, selector, config);
/*
* If the pin controller prefer that a certain group be handled
* pin-by-pin as well, it returns -EAGAIN.
*/
if (ret != -EAGAIN)
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
goto unlock;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
/*
* If the controller cannot handle entire groups, we configure each pin
* individually.
*/
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
if (!ops->pin_config_set) {
ret = 0;
goto unlock;
}
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
for (i = 0; i < num_pins; i++) {
ret = ops->pin_config_set(pctldev, pins[i], config);
if (ret < 0)
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
goto unlock;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
ret = 0;
unlock:
mutex_unlock(&pinctrl_mutex);
return ret;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
}
EXPORT_SYMBOL(pin_config_group_set);
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
int pinconf_map_to_setting(struct pinctrl_map const *map,
struct pinctrl_setting *setting)
{
struct pinctrl_dev *pctldev = setting->pctldev;
pinctrl: fix error path in pinconf_map_to_setting() The code was using the union member setting->data.configs.group_or_pin to store a potential error code, but since that member is unsigned the < 0 comparison was not true, letting errors pass through, ending up as mapped to pin "-22". Fix this up and print the error. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-13 04:38:29 +08:00
int pin;
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
switch (setting->type) {
case PIN_MAP_TYPE_CONFIGS_PIN:
pinctrl: fix error path in pinconf_map_to_setting() The code was using the union member setting->data.configs.group_or_pin to store a potential error code, but since that member is unsigned the < 0 comparison was not true, letting errors pass through, ending up as mapped to pin "-22". Fix this up and print the error. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-13 04:38:29 +08:00
pin = pin_get_from_name(pctldev,
map->data.configs.group_or_pin);
if (pin < 0) {
dev_err(pctldev->dev, "could not map pin config for \"%s\"",
map->data.configs.group_or_pin);
return pin;
}
setting->data.configs.group_or_pin = pin;
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
break;
case PIN_MAP_TYPE_CONFIGS_GROUP:
pinctrl: fix error path in pinconf_map_to_setting() The code was using the union member setting->data.configs.group_or_pin to store a potential error code, but since that member is unsigned the < 0 comparison was not true, letting errors pass through, ending up as mapped to pin "-22". Fix this up and print the error. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-13 04:38:29 +08:00
pin = pinctrl_get_group_selector(pctldev,
map->data.configs.group_or_pin);
if (pin < 0) {
dev_err(pctldev->dev, "could not map group config for \"%s\"",
map->data.configs.group_or_pin);
return pin;
}
setting->data.configs.group_or_pin = pin;
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
break;
default:
return -EINVAL;
}
setting->data.configs.num_configs = map->data.configs.num_configs;
setting->data.configs.configs = map->data.configs.configs;
return 0;
}
void pinconf_free_setting(struct pinctrl_setting const *setting)
{
}
int pinconf_apply_setting(struct pinctrl_setting const *setting)
{
struct pinctrl_dev *pctldev = setting->pctldev;
const struct pinconf_ops *ops = pctldev->desc->confops;
int i, ret;
if (!ops) {
dev_err(pctldev->dev, "missing confops\n");
return -EINVAL;
}
switch (setting->type) {
case PIN_MAP_TYPE_CONFIGS_PIN:
if (!ops->pin_config_set) {
dev_err(pctldev->dev, "missing pin_config_set op\n");
return -EINVAL;
}
for (i = 0; i < setting->data.configs.num_configs; i++) {
ret = ops->pin_config_set(pctldev,
setting->data.configs.group_or_pin,
setting->data.configs.configs[i]);
if (ret < 0) {
dev_err(pctldev->dev,
"pin_config_set op failed for pin %d config %08lx\n",
setting->data.configs.group_or_pin,
setting->data.configs.configs[i]);
return ret;
}
}
break;
case PIN_MAP_TYPE_CONFIGS_GROUP:
if (!ops->pin_config_group_set) {
dev_err(pctldev->dev,
"missing pin_config_group_set op\n");
return -EINVAL;
}
for (i = 0; i < setting->data.configs.num_configs; i++) {
ret = ops->pin_config_group_set(pctldev,
setting->data.configs.group_or_pin,
setting->data.configs.configs[i]);
if (ret < 0) {
dev_err(pctldev->dev,
"pin_config_group_set op failed for group %d config %08lx\n",
setting->data.configs.group_or_pin,
setting->data.configs.configs[i]);
return ret;
}
}
break;
default:
return -EINVAL;
}
return 0;
}
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
#ifdef CONFIG_DEBUG_FS
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
void pinconf_show_map(struct seq_file *s, struct pinctrl_map const *map)
{
pinctrl: allow pctldevs to decode pin config in debugfs Add a pinconf op so that pin controller drivers can decode their pin config settings for debugfs. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-14 00:49:06 +08:00
struct pinctrl_dev *pctldev;
const struct pinconf_ops *confops;
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
int i;
pinctrl: allow pctldevs to decode pin config in debugfs Add a pinconf op so that pin controller drivers can decode their pin config settings for debugfs. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-14 00:49:06 +08:00
pctldev = get_pinctrl_dev_from_devname(map->ctrl_dev_name);
if (pctldev)
confops = pctldev->desc->confops;
else
confops = NULL;
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
switch (map->type) {
case PIN_MAP_TYPE_CONFIGS_PIN:
seq_printf(s, "pin ");
break;
case PIN_MAP_TYPE_CONFIGS_GROUP:
seq_printf(s, "group ");
break;
default:
break;
}
seq_printf(s, "%s\n", map->data.configs.group_or_pin);
pinctrl: allow pctldevs to decode pin config in debugfs Add a pinconf op so that pin controller drivers can decode their pin config settings for debugfs. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-14 00:49:06 +08:00
for (i = 0; i < map->data.configs.num_configs; i++) {
seq_printf(s, "config ");
if (confops && confops->pin_config_config_dbg_show)
confops->pin_config_config_dbg_show(pctldev, s,
map->data.configs.configs[i]);
else
seq_printf(s, "%08lx", map->data.configs.configs[i]);
seq_printf(s, "\n");
}
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
}
void pinconf_show_setting(struct seq_file *s,
struct pinctrl_setting const *setting)
{
struct pinctrl_dev *pctldev = setting->pctldev;
const struct pinctrl_ops *pctlops = pctldev->desc->pctlops;
pinctrl: allow pctldevs to decode pin config in debugfs Add a pinconf op so that pin controller drivers can decode their pin config settings for debugfs. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-14 00:49:06 +08:00
const struct pinconf_ops *confops = pctldev->desc->confops;
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
struct pin_desc *desc;
int i;
switch (setting->type) {
case PIN_MAP_TYPE_CONFIGS_PIN:
desc = pin_desc_get(setting->pctldev,
setting->data.configs.group_or_pin);
seq_printf(s, "pin %s (%d)",
desc->name ? desc->name : "unnamed",
setting->data.configs.group_or_pin);
break;
case PIN_MAP_TYPE_CONFIGS_GROUP:
seq_printf(s, "group %s (%d)",
pctlops->get_group_name(pctldev,
setting->data.configs.group_or_pin),
setting->data.configs.group_or_pin);
break;
default:
break;
}
/*
* FIXME: We should really get the pin controler to dump the config
* values, so they can be decoded to something meaningful.
*/
pinctrl: allow pctldevs to decode pin config in debugfs Add a pinconf op so that pin controller drivers can decode their pin config settings for debugfs. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-14 00:49:06 +08:00
for (i = 0; i < setting->data.configs.num_configs; i++) {
seq_printf(s, " ");
if (confops && confops->pin_config_config_dbg_show)
confops->pin_config_config_dbg_show(pctldev, s,
setting->data.configs.configs[i]);
else
seq_printf(s, "%08lx",
setting->data.configs.configs[i]);
}
pinctrl: enhance mapping table to support pin config operations The pinctrl mapping table can now contain entries to: * Set the mux function of a pin group * Apply a set of pin config options to a pin or a group This allows pinctrl_select_state() to apply pin configs settings as well as mux settings. v3: Fix find_pinctrl() to iterate over the correct list. s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros. Fix documentation to use correct mapping table macro. v2: Added numerous extra PIN_MAP_*() special-case macros. Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and replace it with pin_get_from_name(). Various minor fixes. Updates due to rebase. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:48 +08:00
seq_printf(s, "\n");
}
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
static void pinconf_dump_pin(struct pinctrl_dev *pctldev,
struct seq_file *s, int pin)
{
const struct pinconf_ops *ops = pctldev->desc->confops;
pinctrl: introduce generic pin config This is a split-off from the earlier patch set which adds generic pin configuration for the pin controllers that want it. Since we may have a system with mixed generic and custom pin controllers, we pass a boolean in the pin controller ops vtable to indicate if it is generic. ChangeLog v1->v5: - Follow parent patch versioning number system. - Document the semantic meaning of return values from pin config get functions, so we can iterate over pins and check their properties from debugfs as part of the generic config code. - Use proper cast functions in the generic debugfs pin config file. - Expand generic config to optionally cover groups too. ChangeLog v5->v6: - Update to match underlying changes. ChangeLog v6->v7: - Drop DRIVE_OFF parameter, use bias high impedance for this - Delete argument for drive modes push-pull, od and os. These are now just state transitions. - Delete slew rate rising/falling due to discussions on on proper semantics - Drop config wakeup, struct irq_chip does this for now, add back if need be. - Set PIN_CONFIG_END to 0x7fff making room for custom config parameters from 0x8000 and up. - Prefix accessor functions with pinconf_
2011-11-25 01:27:15 +08:00
/* no-op when not using generic pin config */
pinconf_generic_dump_pin(pctldev, s, pin);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
if (ops && ops->pin_config_dbg_show)
ops->pin_config_dbg_show(pctldev, s, pin);
}
static int pinconf_pins_show(struct seq_file *s, void *what)
{
struct pinctrl_dev *pctldev = s->private;
pinctrl: add some error checking for user interfaces This patch can avoid kernel oops in case the mux or config function is not supported by driver. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-10 12:41:34 +08:00
const struct pinconf_ops *ops = pctldev->desc->confops;
pinctrl: correct a offset while enumerating pins This patch modifies a offset while enumerating pins to support a partial pin space. If we use a pin number for enumerating pins, the pin space always starts with zero base. Indeed, we always check the pin is in the pin space. An extreme example, there is only two pins. One is 0. Another is 1000. We always enumerate whole offsets until 1000. For solving this problem, we use the offset of the pin array instead of the zero-based pin number. Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> [Restored sparse pin space comment] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 15:47:50 +08:00
unsigned i, pin;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: add some error checking for user interfaces This patch can avoid kernel oops in case the mux or config function is not supported by driver. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-10 12:41:34 +08:00
if (!ops || !ops->pin_config_get)
return 0;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
seq_puts(s, "Pin config settings per pin\n");
pinctrl: a minor fix of pin config debug information Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-16 22:07:24 +08:00
seq_puts(s, "Format: pin (name): configs\n");
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
mutex_lock(&pinctrl_mutex);
pinctrl: correct a offset while enumerating pins This patch modifies a offset while enumerating pins to support a partial pin space. If we use a pin number for enumerating pins, the pin space always starts with zero base. Indeed, we always check the pin is in the pin space. An extreme example, there is only two pins. One is 0. Another is 1000. We always enumerate whole offsets until 1000. For solving this problem, we use the offset of the pin array instead of the zero-based pin number. Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> [Restored sparse pin space comment] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 15:47:50 +08:00
/* The pin number can be retrived from the pin controller descriptor */
pinctrl: fix pinconf_pins_show iteration Commit 706e852 "pinctrl: correct a offset while enumerating pins" modified the variable used by pinconf_pin_show()'s for loop, but didn't update the for loop test expression. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-07 04:38:31 +08:00
for (i = 0; i < pctldev->desc->npins; i++) {
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
struct pin_desc *desc;
pinctrl: correct a offset while enumerating pins This patch modifies a offset while enumerating pins to support a partial pin space. If we use a pin number for enumerating pins, the pin space always starts with zero base. Indeed, we always check the pin is in the pin space. An extreme example, there is only two pins. One is 0. Another is 1000. We always enumerate whole offsets until 1000. For solving this problem, we use the offset of the pin array instead of the zero-based pin number. Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> [Restored sparse pin space comment] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 15:47:50 +08:00
pin = pctldev->desc->pins[i].number;
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
desc = pin_desc_get(pctldev, pin);
pinctrl: correct a offset while enumerating pins This patch modifies a offset while enumerating pins to support a partial pin space. If we use a pin number for enumerating pins, the pin space always starts with zero base. Indeed, we always check the pin is in the pin space. An extreme example, there is only two pins. One is 0. Another is 1000. We always enumerate whole offsets until 1000. For solving this problem, we use the offset of the pin array instead of the zero-based pin number. Signed-off-by: Chanho Park <chanho61.park@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> [Restored sparse pin space comment] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-03 15:47:50 +08:00
/* Skip if we cannot search the pin */
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
if (desc == NULL)
continue;
seq_printf(s, "pin %d (%s):", pin,
desc->name ? desc->name : "unnamed");
pinconf_dump_pin(pctldev, s, pin);
seq_printf(s, "\n");
}
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
mutex_unlock(&pinctrl_mutex);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
return 0;
}
static void pinconf_dump_group(struct pinctrl_dev *pctldev,
struct seq_file *s, unsigned selector,
const char *gname)
{
const struct pinconf_ops *ops = pctldev->desc->confops;
pinctrl: introduce generic pin config This is a split-off from the earlier patch set which adds generic pin configuration for the pin controllers that want it. Since we may have a system with mixed generic and custom pin controllers, we pass a boolean in the pin controller ops vtable to indicate if it is generic. ChangeLog v1->v5: - Follow parent patch versioning number system. - Document the semantic meaning of return values from pin config get functions, so we can iterate over pins and check their properties from debugfs as part of the generic config code. - Use proper cast functions in the generic debugfs pin config file. - Expand generic config to optionally cover groups too. ChangeLog v5->v6: - Update to match underlying changes. ChangeLog v6->v7: - Drop DRIVE_OFF parameter, use bias high impedance for this - Delete argument for drive modes push-pull, od and os. These are now just state transitions. - Delete slew rate rising/falling due to discussions on on proper semantics - Drop config wakeup, struct irq_chip does this for now, add back if need be. - Set PIN_CONFIG_END to 0x7fff making room for custom config parameters from 0x8000 and up. - Prefix accessor functions with pinconf_
2011-11-25 01:27:15 +08:00
/* no-op when not using generic pin config */
pinconf_generic_dump_group(pctldev, s, gname);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
if (ops && ops->pin_config_group_dbg_show)
ops->pin_config_group_dbg_show(pctldev, s, selector);
}
static int pinconf_groups_show(struct seq_file *s, void *what)
{
struct pinctrl_dev *pctldev = s->private;
const struct pinctrl_ops *pctlops = pctldev->desc->pctlops;
const struct pinconf_ops *ops = pctldev->desc->confops;
pinctrl: replace list_*() with get_*_count() Most of the SoC drivers implement list_groups() and list_functions() routines for pinctrl and pinmux. These routines continue returning zero until the selector argument is greater than total count of available groups or functions. This patch replaces these list_*() routines with get_*_count() routines, which returns the number of available selection for SoC driver. pinctrl layer will use this value to check the range it can choose. This patch fixes all user drivers for this change. There are other routines in user drivers, which have checks to check validity of selector passed to them. It is also no more required and hence removed. Documentation updated as well. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> [Folded in fix and fixed a minor merge artifact manually] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-30 13:55:40 +08:00
unsigned ngroups = pctlops->get_groups_count(pctldev);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
unsigned selector = 0;
if (!ops || !ops->pin_config_group_get)
return 0;
seq_puts(s, "Pin config settings per pin group\n");
pinctrl: a minor fix of pin config debug information Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-16 22:07:24 +08:00
seq_puts(s, "Format: group (name): configs\n");
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
mutex_lock(&pinctrl_mutex);
pinctrl: replace list_*() with get_*_count() Most of the SoC drivers implement list_groups() and list_functions() routines for pinctrl and pinmux. These routines continue returning zero until the selector argument is greater than total count of available groups or functions. This patch replaces these list_*() routines with get_*_count() routines, which returns the number of available selection for SoC driver. pinctrl layer will use this value to check the range it can choose. This patch fixes all user drivers for this change. There are other routines in user drivers, which have checks to check validity of selector passed to them. It is also no more required and hence removed. Documentation updated as well. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> [Folded in fix and fixed a minor merge artifact manually] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-30 13:55:40 +08:00
while (selector < ngroups) {
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
const char *gname = pctlops->get_group_name(pctldev, selector);
seq_printf(s, "%u (%s):", selector, gname);
pinconf_dump_group(pctldev, s, selector, gname);
pinctrl: fix pinconf_groups_show() to emit newline pinconf_groups_show() wrote all debug information on one line. Fix it to match pinconf_pins_show() and be legible. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-02-20 14:45:58 +08:00
seq_printf(s, "\n");
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
selector++;
}
pinctrl: fix and simplify locking There are many problems with the current pinctrl locking: struct pinctrl_dev's gpio_ranges_lock isn't effective; pinctrl_match_gpio_range() only holds this lock while searching for a gpio range, but the found range is return and manipulated after releading the lock. This could allow pinctrl_remove_gpio_range() for that range while it is in use, and the caller may very well delete the range after removing it, causing pinctrl code to touch the now-free range object. Solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which both gpio range registration and pinctrl_get()/put() will acquire. There is missing locking on HW programming; pin controllers may pack the configuration for different pins/groups/config options/... into one register, and hence have to read-modify-write the register. This needs to be protected, but currently isn't. Related, a future change will add a "complete" op to the pin controller drivers, the idea being that each state's programming will be programmed into the pinctrl driver followed by the "complete" call, which may e.g. flush a register cache to HW. For this to work, it must not be possible to interleave the pinctrl driver calls for different devices. As above, solving this requires the introduction of a higher-level lock, at least a lock per pin controller, which will be held for the duration of any pinctrl_enable()/disable() call. However, each pinctrl mapping table entry may affect a different pin controller if necessary. Hence, with a per-pin-controller lock, almost any pinctrl API may need to acquire multiple locks, one per controller. To avoid deadlock, these would need to be acquired in the same order in all cases. This is extremely difficult to implement in the case of pinctrl_get(), which doesn't know which pin controllers to lock until it has parsed the entire mapping table, since it contains somewhat arbitrary data. The simplest solution here is to introduce a single lock that covers all pin controllers at once. This will be acquired by all pinctrl APIs. This then makes struct pinctrl's mutex irrelevant, since that single lock will always be held whenever this mutex is currently held. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03 04:05:44 +08:00
mutex_unlock(&pinctrl_mutex);
pinctrl: add a pin config interface This add per-pin and per-group pin config interfaces for biasing, driving and other such electronic properties. The details of passed configurations are passed in an opaque unsigned long which may be dereferences to integer types, structs or lists on either side of the configuration interface. ChangeLog v1->v2: - Clear split of terminology: we now have pin controllers, and those may support two interfaces using vtables: pin multiplexing and pin configuration. - Break out pin configuration to its own C file, controllers may implement only config without mux, and vice versa, so keep each sub-functionality of pin controllers separate. Introduce CONFIG_PINCONF in Kconfig. - Implement some core logic around pin configuration in the pinconf.c file. - Remove UNKNOWN config states, these were just surplus baggage. - Remove FLOAT config state - HIGH_IMPEDANCE should be enough for everyone. - PIN_CONFIG_POWER_SOURCE added to handle switching the power supply for the pin logic between different sources - Explicit DISABLE config enums to turn schmitt-trigger, wakeup etc OFF. - Update documentation to reflect all the recent reasoning. ChangeLog v2->v3: - Twist API around to pass around arrays of config tuples instead of (param, value) pairs everywhere. - Explicit drive strength semantics for push/pull and similar drive modes, this shall be the number of drive stages vs nominal load impedance, which should match the actual electronics used in push/pull CMOS or TTY totempoles. - Drop load capacitance configuration - I probably don't know what I'm doing here so leave it out. - Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off. - Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead. - Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off. - Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time on input lines. - Fix a bug when we tried to configure pins for pin controllers without pinconf support. - Initialized debugfs properly so it works. - Initialize the mutex properly and lock around config tampering sections. - Check the return value from get_initial_config() properly. ChangeLog v3->v4: - Export the pin_config_get(), pin_config_set() and pin_config_group() functions. - Drop the entire concept of just getting initial config and keeping track of pin states internally, instead ask the pins what state they are in. Previous idea was plain wrong, if the device cannot keep track of its state, the driver should do it. - Drop the generic configuration layout, it seems this impose too much restriction on some pin controllers, so let them do things the way they want and split off support for generic config as an optional add-on. ChangeLog v4->v5: - Introduce two symmetric driver calls for group configuration, .pin_config_group_[get|set] and corresponding external calls. - Remove generic semantic meanings of return values from config calls, these belong in the generic config patch. Just pass the return value through instead. - Add a debugfs entry "pinconf-groups" to read status from group configuration only, also slam in a per-group debug callback in the pinconf_ops so custom drivers can display something meaningful for their pins. - Fix some dangling newline. - Drop dangling #else clause. - Update documentation to match the above. ChangeLog v5->v6: - Change to using a pin name as parameter for the [get|set]_config() functions, as suggested by Stephen Warren. This is more natural as names will be what a developer has access to in written documentation etc. ChangeLog v6->v7: - Refactor out by-pin and by-name get/set functions, only expose the by-name functions externally, expose the by-pin functions internally. - Show supported pin control functionality in the debugfs pinctrl-devices file. Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-10-20 00:14:33 +08:00
return 0;
}
static int pinconf_pins_open(struct inode *inode, struct file *file)
{
return single_open(file, pinconf_pins_show, inode->i_private);
}
static int pinconf_groups_open(struct inode *inode, struct file *file)
{
return single_open(file, pinconf_groups_show, inode->i_private);
}
static const struct file_operations pinconf_pins_ops = {
.open = pinconf_pins_open,
.read = seq_read,
.llseek = seq_lseek,
.release = single_release,
};
static const struct file_operations pinconf_groups_ops = {
.open = pinconf_groups_open,
.read = seq_read,
.llseek = seq_lseek,
.release = single_release,
};
void pinconf_init_device_debugfs(struct dentry *devroot,
struct pinctrl_dev *pctldev)
{
debugfs_create_file("pinconf-pins", S_IFREG | S_IRUGO,
devroot, pctldev, &pinconf_pins_ops);
debugfs_create_file("pinconf-groups", S_IFREG | S_IRUGO,
devroot, pctldev, &pinconf_groups_ops);
}
#endif