OpenCloudOS-Kernel/include/linux/gpio/driver.h

274 lines
9.2 KiB
C
Raw Normal View History

#ifndef __LINUX_GPIO_DRIVER_H
#define __LINUX_GPIO_DRIVER_H
#include <linux/types.h>
#include <linux/module.h>
#include <linux/irq.h>
#include <linux/irqchip/chained_irq.h>
#include <linux/irqdomain.h>
gpiolib: irqchip: use different lockdep class for each gpio irqchip Since IRQ chip helpers were introduced drivers lose ability to register separate lockdep classes for each registered GPIO IRQ chip and the gpiolib now is using shared lockdep class for all GPIO IRQ chips (gpiochip_irq_lock_class). As result, lockdep will produce warning when there are min two stacked GPIO chips and all of them are interrupt controllers. HW configuration which generates lockdep warning (TI dra7-evm): [SOC GPIO bankA.gpioX] <- irq - [pcf875x.gpioY] <- irq - DevZ.enable_irq_wake(pcf_gpioY_irq); The issue was reported in [1] and discussed [2]. ============================================= [ INFO: possible recursive locking detected ] 4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted --------------------------------------------- sh/63 is trying to acquire lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 but task is already holding lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(class); lock(class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by sh/63: #0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164 #1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0 #2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0 #3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4 #4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398 #5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94 #6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 stack backtrace: CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55 Hardware name: Generic DRA74X (Flattened Device Tree) [<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14) [<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c) [<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20) [<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128) [<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c) [<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94) [<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc) [<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54) [<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc) [<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4) [<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124) [<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398) [<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4) [<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728) [<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4) [<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8) [<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0) [<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8) [<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164) [<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c) [<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54) Lets fix it by using separate lockdep class for each registered GPIO IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros. The implementation of this patch inspired by solution done by Nicolas Boichat for regmap [3] [1] http://www.spinics.net/lists/linux-gpio/msg05844.html [2] http://www.spinics.net/lists/linux-gpio/msg06021.html [3] http://www.spinics.net/lists/arm-kernel/msg429834.html Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roger Quadros <rogerq@ti.com> Reported-by: Roger Quadros <rogerq@ti.com> Tested-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-17 20:35:23 +08:00
#include <linux/lockdep.h>
#include <linux/pinctrl/pinctrl.h>
struct device;
struct gpio_desc;
struct of_phandle_args;
struct device_node;
struct seq_file;
#ifdef CONFIG_GPIOLIB
/**
* struct gpio_chip - abstract a GPIO controller
* @label: for diagnostics
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 16:56:26 +08:00
* @parent: optional parent device providing the GPIOs
* @cdev: class device used by sysfs interface (may be NULL)
* @owner: helps prevent removal of modules exporting active GPIOs
* @list: links gpio_chips together for traversal
* @request: optional hook for chip-specific activation, such as
* enabling module power and clock; may sleep
* @free: optional hook for chip-specific deactivation, such as
* disabling module power and clock; may sleep
* @get_direction: returns direction for signal "offset", 0=out, 1=in,
* (same as GPIOF_DIR_XXX), or negative error
* @direction_input: configures signal "offset" as input, or returns error
* @direction_output: configures signal "offset" as output, or returns error
* @get: returns value for signal "offset", 0=low, 1=high, or negative error
* @set: assigns output value for signal "offset"
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-05 00:12:06 +08:00
* @set_multiple: assigns output values for multiple signals defined by "mask"
* @set_debounce: optional hook for setting debounce time for specified gpio in
* interrupt triggered gpio chips
* @to_irq: optional hook supporting non-static gpio_to_irq() mappings;
* implementation may not sleep
* @dbg_show: optional routine to show contents in debugfs; default code
* will be used when this is omitted, but custom code can show extra
* state (such as pullup/pulldown configuration).
* @base: identifies the first GPIO number handled by this chip;
* or, if negative during registration, requests dynamic ID allocation.
* DEPRECATION: providing anything non-negative and nailing the base
* offset of GPIO chips is deprecated. Please pass -1 as base to
* let gpiolib select the chip base in all possible cases. We want to
* get rid of the static GPIO number space in the long run.
* @ngpio: the number of GPIOs handled by this controller; the last GPIO
* handled is (base + ngpio - 1).
* @desc: array of ngpio descriptors. Private.
* @names: if set, must be an array of strings to use as alternative
* names for the GPIOs in this chip. Any entry in the array
* may be NULL if there is no alias for the GPIO, however the
* array must be @ngpio entries long. A name can include a single printk
* format specifier for an unsigned int. It is substituted by the actual
* number of the gpio.
* @can_sleep: flag must be set iff get()/set() methods sleep, as they
* must while accessing GPIO expander chips over I2C or SPI. This
* implies that if the chip supports IRQs, these IRQs need to be threaded
* as the chip access may sleep when e.g. reading out the IRQ status
* registers.
* @irq_not_threaded: flag must be set if @can_sleep is set but the
* IRQs don't need to be threaded
* @irqchip: GPIO IRQ chip impl, provided by GPIO driver
* @irqdomain: Interrupt translation domain; responsible for mapping
* between GPIO hwirq number and linux irq number
* @irq_base: first linux IRQ number assigned to GPIO IRQ chip (deprecated)
* @irq_handler: the irq handler to use (often a predefined irq core function)
* for GPIO IRQs, provided by GPIO driver
* @irq_default_type: default IRQ triggering type applied during GPIO driver
* initialization, provided by GPIO driver
* @irq_parent: GPIO IRQ chip parent/bank linux irq number,
* provided by GPIO driver
* @lock_key: per GPIO IRQ chip lockdep class
*
* A gpio_chip can help platforms abstract various sources of GPIOs so
* they can all be accessed through a common programing interface.
* Example sources would be SOC controllers, FPGAs, multifunction
* chips, dedicated GPIO expanders, and so on.
*
* Each chip controls a number of signals, identified in method calls
* by "offset" values in the range 0..(@ngpio - 1). When those signals
* are referenced through calls like gpio_get_value(gpio), the offset
* is calculated by subtracting @base from the gpio number.
*/
struct gpio_chip {
const char *label;
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 16:56:26 +08:00
struct device *parent;
struct device *cdev;
struct module *owner;
struct list_head list;
int (*request)(struct gpio_chip *chip,
unsigned offset);
void (*free)(struct gpio_chip *chip,
unsigned offset);
int (*get_direction)(struct gpio_chip *chip,
unsigned offset);
int (*direction_input)(struct gpio_chip *chip,
unsigned offset);
int (*direction_output)(struct gpio_chip *chip,
unsigned offset, int value);
int (*get)(struct gpio_chip *chip,
unsigned offset);
void (*set)(struct gpio_chip *chip,
unsigned offset, int value);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-05 00:12:06 +08:00
void (*set_multiple)(struct gpio_chip *chip,
unsigned long *mask,
unsigned long *bits);
int (*set_debounce)(struct gpio_chip *chip,
unsigned offset,
unsigned debounce);
int (*to_irq)(struct gpio_chip *chip,
unsigned offset);
void (*dbg_show)(struct seq_file *s,
struct gpio_chip *chip);
int base;
u16 ngpio;
struct gpio_desc *desc;
const char *const *names;
bool can_sleep;
bool irq_not_threaded;
#ifdef CONFIG_GPIOLIB_IRQCHIP
/*
* With CONFIG_GPIOLIB_IRQCHIP we get an irqchip inside the gpiolib
* to handle IRQs for most practical cases.
*/
struct irq_chip *irqchip;
struct irq_domain *irqdomain;
unsigned int irq_base;
irq_flow_handler_t irq_handler;
unsigned int irq_default_type;
int irq_parent;
gpiolib: irqchip: use different lockdep class for each gpio irqchip Since IRQ chip helpers were introduced drivers lose ability to register separate lockdep classes for each registered GPIO IRQ chip and the gpiolib now is using shared lockdep class for all GPIO IRQ chips (gpiochip_irq_lock_class). As result, lockdep will produce warning when there are min two stacked GPIO chips and all of them are interrupt controllers. HW configuration which generates lockdep warning (TI dra7-evm): [SOC GPIO bankA.gpioX] <- irq - [pcf875x.gpioY] <- irq - DevZ.enable_irq_wake(pcf_gpioY_irq); The issue was reported in [1] and discussed [2]. ============================================= [ INFO: possible recursive locking detected ] 4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted --------------------------------------------- sh/63 is trying to acquire lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 but task is already holding lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(class); lock(class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by sh/63: #0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164 #1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0 #2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0 #3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4 #4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398 #5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94 #6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 stack backtrace: CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55 Hardware name: Generic DRA74X (Flattened Device Tree) [<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14) [<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c) [<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20) [<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128) [<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c) [<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94) [<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc) [<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54) [<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc) [<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4) [<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124) [<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398) [<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4) [<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728) [<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4) [<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8) [<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0) [<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8) [<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164) [<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c) [<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54) Lets fix it by using separate lockdep class for each registered GPIO IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros. The implementation of this patch inspired by solution done by Nicolas Boichat for regmap [3] [1] http://www.spinics.net/lists/linux-gpio/msg05844.html [2] http://www.spinics.net/lists/linux-gpio/msg06021.html [3] http://www.spinics.net/lists/arm-kernel/msg429834.html Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roger Quadros <rogerq@ti.com> Reported-by: Roger Quadros <rogerq@ti.com> Tested-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-17 20:35:23 +08:00
struct lock_class_key *lock_key;
#endif
#if defined(CONFIG_OF_GPIO)
/*
* If CONFIG_OF is enabled, then all GPIO controllers described in the
* device tree automatically may have an OF translation
*/
struct device_node *of_node;
int of_gpio_n_cells;
int (*of_xlate)(struct gpio_chip *gc,
const struct of_phandle_args *gpiospec, u32 *flags);
#endif
#ifdef CONFIG_PINCTRL
/*
* If CONFIG_PINCTRL is enabled, then gpio controllers can optionally
* describe the actual pin range which they serve in an SoC. This
* information would be used by pinctrl subsystem to configure
* corresponding pins for gpio usage.
*/
struct list_head pin_ranges;
#endif
};
extern const char *gpiochip_is_requested(struct gpio_chip *chip,
unsigned offset);
/* add/remove chips */
extern int gpiochip_add(struct gpio_chip *chip);
extern void gpiochip_remove(struct gpio_chip *chip);
extern struct gpio_chip *gpiochip_find(void *data,
int (*match)(struct gpio_chip *chip, void *data));
/* lock/unlock as IRQ */
int gpiochip_lock_as_irq(struct gpio_chip *chip, unsigned int offset);
void gpiochip_unlock_as_irq(struct gpio_chip *chip, unsigned int offset);
struct gpio_chip *gpiod_to_chip(const struct gpio_desc *desc);
#ifdef CONFIG_GPIOLIB_IRQCHIP
void gpiochip_set_chained_irqchip(struct gpio_chip *gpiochip,
struct irq_chip *irqchip,
int parent_irq,
irq_flow_handler_t parent_handler);
gpiolib: irqchip: use different lockdep class for each gpio irqchip Since IRQ chip helpers were introduced drivers lose ability to register separate lockdep classes for each registered GPIO IRQ chip and the gpiolib now is using shared lockdep class for all GPIO IRQ chips (gpiochip_irq_lock_class). As result, lockdep will produce warning when there are min two stacked GPIO chips and all of them are interrupt controllers. HW configuration which generates lockdep warning (TI dra7-evm): [SOC GPIO bankA.gpioX] <- irq - [pcf875x.gpioY] <- irq - DevZ.enable_irq_wake(pcf_gpioY_irq); The issue was reported in [1] and discussed [2]. ============================================= [ INFO: possible recursive locking detected ] 4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted --------------------------------------------- sh/63 is trying to acquire lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 but task is already holding lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(class); lock(class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by sh/63: #0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164 #1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0 #2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0 #3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4 #4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398 #5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94 #6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 stack backtrace: CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55 Hardware name: Generic DRA74X (Flattened Device Tree) [<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14) [<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c) [<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20) [<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128) [<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c) [<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94) [<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc) [<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54) [<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc) [<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4) [<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124) [<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398) [<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4) [<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728) [<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4) [<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8) [<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0) [<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8) [<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164) [<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c) [<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54) Lets fix it by using separate lockdep class for each registered GPIO IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros. The implementation of this patch inspired by solution done by Nicolas Boichat for regmap [3] [1] http://www.spinics.net/lists/linux-gpio/msg05844.html [2] http://www.spinics.net/lists/linux-gpio/msg06021.html [3] http://www.spinics.net/lists/arm-kernel/msg429834.html Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roger Quadros <rogerq@ti.com> Reported-by: Roger Quadros <rogerq@ti.com> Tested-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-17 20:35:23 +08:00
int _gpiochip_irqchip_add(struct gpio_chip *gpiochip,
struct irq_chip *irqchip,
unsigned int first_irq,
irq_flow_handler_t handler,
unsigned int type,
struct lock_class_key *lock_key);
#ifdef CONFIG_LOCKDEP
#define gpiochip_irqchip_add(...) \
( \
({ \
static struct lock_class_key _key; \
_gpiochip_irqchip_add(__VA_ARGS__, &_key); \
}) \
)
#else
#define gpiochip_irqchip_add(...) \
_gpiochip_irqchip_add(__VA_ARGS__, NULL)
#endif
#endif /* CONFIG_GPIOLIB_IRQCHIP */
int gpiochip_generic_request(struct gpio_chip *chip, unsigned offset);
void gpiochip_generic_free(struct gpio_chip *chip, unsigned offset);
#ifdef CONFIG_PINCTRL
/**
* struct gpio_pin_range - pin range controlled by a gpio chip
* @head: list for maintaining set of pin ranges, used internally
* @pctldev: pinctrl device which handles corresponding pins
* @range: actual range of pins controlled by a gpio controller
*/
struct gpio_pin_range {
struct list_head node;
struct pinctrl_dev *pctldev;
struct pinctrl_gpio_range range;
};
int gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
unsigned int gpio_offset, unsigned int pin_offset,
unsigned int npins);
int gpiochip_add_pingroup_range(struct gpio_chip *chip,
struct pinctrl_dev *pctldev,
unsigned int gpio_offset, const char *pin_group);
void gpiochip_remove_pin_ranges(struct gpio_chip *chip);
#else
static inline int
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
unsigned int gpio_offset, unsigned int pin_offset,
unsigned int npins)
{
return 0;
}
static inline int
gpiochip_add_pingroup_range(struct gpio_chip *chip,
struct pinctrl_dev *pctldev,
unsigned int gpio_offset, const char *pin_group)
{
return 0;
}
static inline void
gpiochip_remove_pin_ranges(struct gpio_chip *chip)
{
}
#endif /* CONFIG_PINCTRL */
struct gpio_desc *gpiochip_request_own_desc(struct gpio_chip *chip, u16 hwnum,
const char *label);
void gpiochip_free_own_desc(struct gpio_desc *desc);
#else /* CONFIG_GPIOLIB */
static inline struct gpio_chip *gpiod_to_chip(const struct gpio_desc *desc)
{
/* GPIO can never have been requested */
WARN_ON(1);
return ERR_PTR(-ENODEV);
}
#endif /* CONFIG_GPIOLIB */
#endif