2011-08-02 19:32:06 +08:00
|
|
|
dm-raid
|
2013-04-24 09:42:43 +08:00
|
|
|
=======
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
|
2011-08-02 19:32:06 +08:00
|
|
|
The device-mapper RAID (dm-raid) target provides a bridge from DM to MD.
|
|
|
|
It allows the MD RAID drivers to be accessed using a device-mapper
|
|
|
|
interface.
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
|
2013-04-24 09:42:43 +08:00
|
|
|
|
|
|
|
Mapping Table Interface
|
|
|
|
-----------------------
|
2011-08-02 19:32:06 +08:00
|
|
|
The target is named "raid" and it accepts the following parameters:
|
|
|
|
|
|
|
|
<raid_type> <#raid_params> <raid_params> \
|
|
|
|
<#raid_devs> <metadata_dev0> <dev0> [.. <metadata_devN> <devN>]
|
|
|
|
|
|
|
|
<raid_type>:
|
2016-06-14 07:46:01 +08:00
|
|
|
raid0 RAID0 striping (no resilience)
|
2011-08-02 19:32:07 +08:00
|
|
|
raid1 RAID1 mirroring
|
2016-06-14 07:46:01 +08:00
|
|
|
raid4 RAID4 with dedicated last parity disk
|
2016-10-17 20:17:10 +08:00
|
|
|
raid5_n RAID5 with dedicated last parity disk supporting takeover
|
2016-06-14 07:46:01 +08:00
|
|
|
Same as raid4
|
|
|
|
-Transitory layout
|
2011-08-02 19:32:06 +08:00
|
|
|
raid5_la RAID5 left asymmetric
|
|
|
|
- rotating parity 0 with data continuation
|
|
|
|
raid5_ra RAID5 right asymmetric
|
|
|
|
- rotating parity N with data continuation
|
|
|
|
raid5_ls RAID5 left symmetric
|
|
|
|
- rotating parity 0 with data restart
|
|
|
|
raid5_rs RAID5 right symmetric
|
|
|
|
- rotating parity N with data restart
|
|
|
|
raid6_zr RAID6 zero restart
|
|
|
|
- rotating parity zero (left-to-right) with data restart
|
|
|
|
raid6_nr RAID6 N restart
|
|
|
|
- rotating parity N (right-to-left) with data restart
|
|
|
|
raid6_nc RAID6 N continue
|
|
|
|
- rotating parity N (right-to-left) with data continuation
|
2016-06-14 07:46:01 +08:00
|
|
|
raid6_n_6 RAID6 with dedicate parity disks
|
|
|
|
- parity and Q-syndrome on the last 2 disks;
|
2016-10-17 20:17:10 +08:00
|
|
|
layout for takeover from/to raid4/raid5_n
|
2016-06-14 07:46:01 +08:00
|
|
|
raid6_la_6 Same as "raid_la" plus dedicated last Q-syndrome disk
|
|
|
|
- layout for takeover from raid5_la from/to raid6
|
|
|
|
raid6_ra_6 Same as "raid5_ra" dedicated last Q-syndrome disk
|
|
|
|
- layout for takeover from raid5_ra from/to raid6
|
|
|
|
raid6_ls_6 Same as "raid5_ls" dedicated last Q-syndrome disk
|
|
|
|
- layout for takeover from raid5_ls from/to raid6
|
|
|
|
raid6_rs_6 Same as "raid5_rs" dedicated last Q-syndrome disk
|
|
|
|
- layout for takeover from raid5_rs from/to raid6
|
2012-08-01 10:44:26 +08:00
|
|
|
raid10 Various RAID10 inspired algorithms chosen by additional params
|
2016-06-14 07:46:01 +08:00
|
|
|
(see raid10_format and raid10_copies below)
|
2012-08-01 10:44:26 +08:00
|
|
|
- RAID10: Striped Mirrors (aka 'Striping on top of mirrors')
|
|
|
|
- RAID1E: Integrated Adjacent Stripe Mirroring
|
2013-02-21 10:28:10 +08:00
|
|
|
- RAID1E: Integrated Offset Stripe Mirroring
|
2012-08-01 10:44:26 +08:00
|
|
|
- and other similar RAID10 variants
|
2011-08-02 19:32:06 +08:00
|
|
|
|
2012-03-04 22:16:11 +08:00
|
|
|
Reference: Chapter 4 of
|
2011-08-02 19:32:06 +08:00
|
|
|
http://www.snia.org/sites/default/files/SNIA_DDF_Technical_Position_v2.0.pdf
|
|
|
|
|
|
|
|
<#raid_params>: The number of parameters that follow.
|
|
|
|
|
|
|
|
<raid_params> consists of
|
|
|
|
Mandatory parameters:
|
|
|
|
<chunk_size>: Chunk size in sectors. This parameter is often known as
|
|
|
|
"stripe size". It is the only mandatory parameter and
|
|
|
|
is placed first.
|
|
|
|
|
|
|
|
followed by optional parameters (in any order):
|
|
|
|
[sync|nosync] Force or prevent RAID initialization.
|
|
|
|
|
2013-04-24 09:42:43 +08:00
|
|
|
[rebuild <idx>] Rebuild drive number 'idx' (first drive is 0).
|
2011-08-02 19:32:06 +08:00
|
|
|
|
|
|
|
[daemon_sleep <ms>]
|
|
|
|
Interval between runs of the bitmap daemon that
|
|
|
|
clear bits. A longer interval means less bitmap I/O but
|
|
|
|
resyncing after a failure is likely to take longer.
|
|
|
|
|
|
|
|
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
|
|
|
|
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
|
2013-04-24 09:42:43 +08:00
|
|
|
[write_mostly <idx>] Mark drive index 'idx' write-mostly.
|
|
|
|
[max_write_behind <sectors>] See '--write-behind=' (man mdadm)
|
|
|
|
[stripe_cache <sectors>] Stripe cache size (RAID 4/5/6 only)
|
2011-08-02 19:32:07 +08:00
|
|
|
[region_size <sectors>]
|
|
|
|
The region_size multiplied by the number of regions is the
|
|
|
|
logical size of the array. The bitmap records the device
|
|
|
|
synchronisation state for each region.
|
2011-08-02 19:32:06 +08:00
|
|
|
|
2012-08-01 10:44:26 +08:00
|
|
|
[raid10_copies <# copies>]
|
2013-02-21 10:28:10 +08:00
|
|
|
[raid10_format <near|far|offset>]
|
2012-08-01 10:44:26 +08:00
|
|
|
These two options are used to alter the default layout of
|
|
|
|
a RAID10 configuration. The number of copies is can be
|
2013-02-21 10:28:10 +08:00
|
|
|
specified, but the default is 2. There are also three
|
|
|
|
variations to how the copies are laid down - the default
|
|
|
|
is "near". Near copies are what most people think of with
|
|
|
|
respect to mirroring. If these options are left unspecified,
|
|
|
|
or 'raid10_copies 2' and/or 'raid10_format near' are given,
|
|
|
|
then the layouts for 2, 3 and 4 devices are:
|
2012-08-01 10:44:26 +08:00
|
|
|
2 drives 3 drives 4 drives
|
|
|
|
-------- ---------- --------------
|
|
|
|
A1 A1 A1 A1 A2 A1 A1 A2 A2
|
|
|
|
A2 A2 A2 A3 A3 A3 A3 A4 A4
|
|
|
|
A3 A3 A4 A4 A5 A5 A5 A6 A6
|
|
|
|
A4 A4 A5 A6 A6 A7 A7 A8 A8
|
|
|
|
.. .. .. .. .. .. .. .. ..
|
|
|
|
The 2-device layout is equivalent 2-way RAID1. The 4-device
|
|
|
|
layout is what a traditional RAID10 would look like. The
|
|
|
|
3-device layout is what might be called a 'RAID1E - Integrated
|
|
|
|
Adjacent Stripe Mirroring'.
|
|
|
|
|
2013-02-21 10:28:10 +08:00
|
|
|
If 'raid10_copies 2' and 'raid10_format far', then the layouts
|
|
|
|
for 2, 3 and 4 devices are:
|
|
|
|
2 drives 3 drives 4 drives
|
|
|
|
-------- -------------- --------------------
|
|
|
|
A1 A2 A1 A2 A3 A1 A2 A3 A4
|
|
|
|
A3 A4 A4 A5 A6 A5 A6 A7 A8
|
|
|
|
A5 A6 A7 A8 A9 A9 A10 A11 A12
|
|
|
|
.. .. .. .. .. .. .. .. ..
|
|
|
|
A2 A1 A3 A1 A2 A2 A1 A4 A3
|
|
|
|
A4 A3 A6 A4 A5 A6 A5 A8 A7
|
|
|
|
A6 A5 A9 A7 A8 A10 A9 A12 A11
|
|
|
|
.. .. .. .. .. .. .. .. ..
|
|
|
|
|
|
|
|
If 'raid10_copies 2' and 'raid10_format offset', then the
|
|
|
|
layouts for 2, 3 and 4 devices are:
|
|
|
|
2 drives 3 drives 4 drives
|
|
|
|
-------- ------------ -----------------
|
|
|
|
A1 A2 A1 A2 A3 A1 A2 A3 A4
|
|
|
|
A2 A1 A3 A1 A2 A2 A1 A4 A3
|
|
|
|
A3 A4 A4 A5 A6 A5 A6 A7 A8
|
|
|
|
A4 A3 A6 A4 A5 A6 A5 A8 A7
|
|
|
|
A5 A6 A7 A8 A9 A9 A10 A11 A12
|
|
|
|
A6 A5 A9 A7 A8 A10 A9 A12 A11
|
|
|
|
.. .. .. .. .. .. .. .. ..
|
|
|
|
Here we see layouts closely akin to 'RAID1E - Integrated
|
|
|
|
Offset Stripe Mirroring'.
|
|
|
|
|
2016-06-14 07:46:01 +08:00
|
|
|
[delta_disks <N>]
|
|
|
|
The delta_disks option value (-251 < N < +251) triggers
|
|
|
|
device removal (negative value) or device addition (positive
|
|
|
|
value) to any reshape supporting raid levels 4/5/6 and 10.
|
|
|
|
RAID levels 4/5/6 allow for addition of devices (metadata
|
2016-10-17 20:17:10 +08:00
|
|
|
and data device tuple), raid10_near and raid10_offset only
|
|
|
|
allow for device addition. raid10_far does not support any
|
2016-06-14 07:46:01 +08:00
|
|
|
reshaping at all.
|
|
|
|
A minimum of devices have to be kept to enforce resilience,
|
|
|
|
which is 3 devices for raid4/5 and 4 devices for raid6.
|
|
|
|
|
|
|
|
[data_offset <sectors>]
|
|
|
|
This option value defines the offset into each data device
|
|
|
|
where the data starts. This is used to provide out-of-place
|
|
|
|
reshaping space to avoid writing over data whilst
|
|
|
|
changing the layout of stripes, hence an interruption/crash
|
|
|
|
may happen at any time without the risk of losing data.
|
|
|
|
E.g. when adding devices to an existing raid set during
|
|
|
|
forward reshaping, the out-of-place space will be allocated
|
|
|
|
at the beginning of each raid device. The kernel raid4/5/6/10
|
|
|
|
MD personalities supporting such device addition will read the data from
|
|
|
|
the existing first stripes (those with smaller number of stripes)
|
|
|
|
starting at data_offset to fill up a new stripe with the larger
|
|
|
|
number of stripes, calculate the redundancy blocks (CRC/Q-syndrome)
|
|
|
|
and write that new stripe to offset 0. Same will be applied to all
|
|
|
|
N-1 other new stripes. This out-of-place scheme is used to change
|
|
|
|
the RAID type (i.e. the allocation algorithm) as well, e.g.
|
|
|
|
changing from raid5_ls to raid5_n.
|
|
|
|
|
2016-12-01 05:31:05 +08:00
|
|
|
[journal_dev <dev>]
|
|
|
|
This option adds a journal device to raid4/5/6 raid sets and
|
|
|
|
uses it to close the 'write hole' caused by the non-atomic updates
|
|
|
|
to the component devices which can cause data loss during recovery.
|
|
|
|
The journal device is used as writethrough thus causing writes to
|
|
|
|
be throttled versus non-journaled raid4/5/6 sets.
|
|
|
|
Takeover/reshape is not possible with a raid4/5/6 journal device;
|
|
|
|
it has to be deconfigured before requesting these.
|
|
|
|
|
2017-03-23 00:44:38 +08:00
|
|
|
[journal_mode <mode>]
|
|
|
|
This option sets the caching mode on journaled raid4/5/6 raid sets
|
|
|
|
(see 'journal_dev <dev>' above) to 'writethrough' or 'writeback'.
|
|
|
|
If 'writeback' is selected the journal device has to be resilient
|
|
|
|
and must not suffer from the 'write hole' problem itself (e.g. use
|
|
|
|
raid1 or raid10) to avoid a single point of failure.
|
|
|
|
|
2011-08-02 19:32:06 +08:00
|
|
|
<#raid_devs>: The number of devices composing the array.
|
|
|
|
Each device consists of two entries. The first is the device
|
|
|
|
containing the metadata (if any); the second is the one containing the
|
2016-06-14 07:46:01 +08:00
|
|
|
data. A Maximum of 64 metadata/data device entries are supported
|
|
|
|
up to target version 1.8.0.
|
|
|
|
1.9.0 supports up to 253 which is enforced by the used MD kernel runtime.
|
2011-08-02 19:32:06 +08:00
|
|
|
|
|
|
|
If a drive has failed or is missing at creation time, a '-' can be
|
|
|
|
given for both the metadata and data drives for a given position.
|
|
|
|
|
|
|
|
|
2013-04-24 09:42:43 +08:00
|
|
|
Example Tables
|
2011-08-02 19:32:06 +08:00
|
|
|
--------------
|
2011-08-02 19:32:07 +08:00
|
|
|
# RAID4 - 4 data drives, 1 parity (no metadata devices)
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
# No metadata devices specified to hold superblock/bitmap info
|
|
|
|
# Chunk size of 1MiB
|
|
|
|
# (Lines separated for easy reading)
|
2011-08-02 19:32:06 +08:00
|
|
|
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
0 1960893648 raid \
|
|
|
|
raid4 1 2048 \
|
|
|
|
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
|
|
|
|
|
2011-08-02 19:32:07 +08:00
|
|
|
# RAID4 - 4 data drives, 1 parity (with metadata devices)
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
# Chunk size of 1MiB, force RAID initialization,
|
|
|
|
# min recovery rate at 20 kiB/sec/disk
|
2011-08-02 19:32:06 +08:00
|
|
|
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
0 1960893648 raid \
|
2011-08-02 19:32:07 +08:00
|
|
|
raid4 4 2048 sync min_recovery_rate 20 \
|
|
|
|
5 8:17 8:18 8:33 8:34 8:49 8:50 8:65 8:66 8:81 8:82
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
|
2013-04-24 09:42:43 +08:00
|
|
|
|
|
|
|
Status Output
|
|
|
|
-------------
|
2011-08-02 19:32:06 +08:00
|
|
|
'dmsetup table' displays the table used to construct the mapping.
|
2011-08-02 19:32:07 +08:00
|
|
|
The optional parameters are always printed in the order listed
|
2011-08-02 19:32:06 +08:00
|
|
|
above with "sync" or "nosync" always output ahead of the other
|
|
|
|
arguments, regardless of the order used when originally loading the table.
|
2011-08-02 19:32:07 +08:00
|
|
|
Arguments that can be repeated are ordered by value.
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
|
2013-04-24 09:42:43 +08:00
|
|
|
|
|
|
|
'dmsetup status' yields information on the state and health of the array.
|
|
|
|
The output is as follows (normally a single line, but expanded here for
|
|
|
|
clarity):
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
1: <s> <l> raid \
|
2013-04-24 09:42:43 +08:00
|
|
|
2: <raid_type> <#devices> <health_chars> \
|
|
|
|
3: <sync_ratio> <sync_action> <mismatch_cnt>
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
|
2011-08-02 19:32:06 +08:00
|
|
|
Line 1 is the standard output produced by device-mapper.
|
2013-04-24 09:42:43 +08:00
|
|
|
Line 2 & 3 are produced by the raid target and are best explained by example:
|
|
|
|
0 1960893648 raid raid4 5 AAAAA 2/490221568 init 0
|
dm: raid456 basic support
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2011-01-14 04:00:02 +08:00
|
|
|
Here we can see the RAID type is raid4, there are 5 devices - all of
|
2013-04-24 09:42:43 +08:00
|
|
|
which are 'A'live, and the array is 2/490221568 complete with its initial
|
|
|
|
recovery. Here is a fuller description of the individual fields:
|
|
|
|
<raid_type> Same as the <raid_type> used to create the array.
|
|
|
|
<health_chars> One char for each device, indicating: 'A' = alive and
|
|
|
|
in-sync, 'a' = alive but not in-sync, 'D' = dead/failed.
|
|
|
|
<sync_ratio> The ratio indicating how much of the array has undergone
|
|
|
|
the process described by 'sync_action'. If the
|
|
|
|
'sync_action' is "check" or "repair", then the process
|
|
|
|
of "resync" or "recover" can be considered complete.
|
|
|
|
<sync_action> One of the following possible states:
|
|
|
|
idle - No synchronization action is being performed.
|
|
|
|
frozen - The current action has been halted.
|
|
|
|
resync - Array is undergoing its initial synchronization
|
|
|
|
or is resynchronizing after an unclean shutdown
|
|
|
|
(possibly aided by a bitmap).
|
|
|
|
recover - A device in the array is being rebuilt or
|
|
|
|
replaced.
|
|
|
|
check - A user-initiated full check of the array is
|
|
|
|
being performed. All blocks are read and
|
|
|
|
checked for consistency. The number of
|
|
|
|
discrepancies found are recorded in
|
|
|
|
<mismatch_cnt>. No changes are made to the
|
|
|
|
array by this action.
|
|
|
|
repair - The same as "check", but discrepancies are
|
|
|
|
corrected.
|
|
|
|
reshape - The array is undergoing a reshape.
|
|
|
|
<mismatch_cnt> The number of discrepancies found between mirror copies
|
|
|
|
in RAID1/10 or wrong parity values found in RAID4/5/6.
|
|
|
|
This value is valid only after a "check" of the array
|
|
|
|
is performed. A healthy array has a 'mismatch_cnt' of 0.
|
2016-11-30 02:26:08 +08:00
|
|
|
<data_offset> The current data offset to the start of the user data on
|
|
|
|
each component device of a raid set (see the respective
|
|
|
|
raid parameter to support out-of-place reshaping).
|
2017-03-23 00:44:38 +08:00
|
|
|
<journal_char> 'A' - active write-through journal device.
|
|
|
|
'a' - active write-back journal device.
|
2016-12-01 05:31:05 +08:00
|
|
|
'D' - dead journal device.
|
|
|
|
'-' - no journal device.
|
2016-11-30 02:26:08 +08:00
|
|
|
|
2013-04-24 09:42:43 +08:00
|
|
|
|
|
|
|
Message Interface
|
|
|
|
-----------------
|
|
|
|
The dm-raid target will accept certain actions through the 'message' interface.
|
|
|
|
('man dmsetup' for more information on the message interface.) These actions
|
|
|
|
include:
|
|
|
|
"idle" - Halt the current sync action.
|
|
|
|
"frozen" - Freeze the current sync action.
|
|
|
|
"resync" - Initiate/continue a resync.
|
|
|
|
"recover"- Initiate/continue a recover process.
|
|
|
|
"check" - Initiate a check (i.e. a "scrub") of the array.
|
|
|
|
"repair" - Initiate a repair of the array.
|
2012-10-11 10:40:24 +08:00
|
|
|
|
2015-08-25 23:15:41 +08:00
|
|
|
|
|
|
|
Discard Support
|
|
|
|
---------------
|
|
|
|
The implementation of discard support among hardware vendors varies.
|
|
|
|
When a block is discarded, some storage devices will return zeroes when
|
|
|
|
the block is read. These devices set the 'discard_zeroes_data'
|
|
|
|
attribute. Other devices will return random data. Confusingly, some
|
|
|
|
devices that advertise 'discard_zeroes_data' will not reliably return
|
|
|
|
zeroes when discarded blocks are read! Since RAID 4/5/6 uses blocks
|
|
|
|
from a number of devices to calculate parity blocks and (for performance
|
|
|
|
reasons) relies on 'discard_zeroes_data' being reliable, it is important
|
|
|
|
that the devices be consistent. Blocks may be discarded in the middle
|
|
|
|
of a RAID 4/5/6 stripe and if subsequent read results are not
|
|
|
|
consistent, the parity blocks may be calculated differently at any time;
|
|
|
|
making the parity blocks useless for redundancy. It is important to
|
|
|
|
understand how your hardware behaves with discards if you are going to
|
|
|
|
enable discards with RAID 4/5/6.
|
|
|
|
|
|
|
|
Since the behavior of storage devices is unreliable in this respect,
|
|
|
|
even when reporting 'discard_zeroes_data', by default RAID 4/5/6
|
|
|
|
discard support is disabled -- this ensures data integrity at the
|
|
|
|
expense of losing some performance.
|
|
|
|
|
|
|
|
Storage devices that properly support 'discard_zeroes_data' are
|
|
|
|
increasingly whitelisted in the kernel and can thus be trusted.
|
|
|
|
|
|
|
|
For trusted devices, the following dm-raid module parameter can be set
|
|
|
|
to safely enable discard support for RAID 4/5/6:
|
|
|
|
'devices_handle_discards_safely'
|
|
|
|
|
|
|
|
|
2012-10-11 10:40:24 +08:00
|
|
|
Version History
|
|
|
|
---------------
|
|
|
|
1.0.0 Initial version. Support for RAID 4/5/6
|
|
|
|
1.1.0 Added support for RAID 1
|
|
|
|
1.2.0 Handle creation of arrays that contain failed devices.
|
|
|
|
1.3.0 Added support for RAID 10
|
|
|
|
1.3.1 Allow device replacement/rebuild for RAID 10
|
2013-01-23 11:42:18 +08:00
|
|
|
1.3.2 Fix/improve redundancy checking for RAID10
|
2013-02-21 10:28:10 +08:00
|
|
|
1.4.0 Non-functional change. Removes arg from mapping function.
|
2013-04-24 09:42:43 +08:00
|
|
|
1.4.1 RAID10 fix redundancy validation checks (commit 55ebbb5).
|
|
|
|
1.4.2 Add RAID10 "far" and "offset" algorithm support.
|
|
|
|
1.5.0 Add message interface to allow manipulation of the sync_action.
|
|
|
|
New status (STATUSTYPE_INFO) fields: sync_action and mismatch_cnt.
|
2013-05-03 03:19:24 +08:00
|
|
|
1.5.1 Add ability to restore transiently failed devices on resume.
|
2013-06-25 14:23:59 +08:00
|
|
|
1.5.2 'mismatch_cnt' is zero unless [last_]sync_action is "check".
|
2015-04-29 20:03:07 +08:00
|
|
|
1.6.0 Add discard support (and devices_handle_discard_safely module param).
|
2015-04-29 20:03:04 +08:00
|
|
|
1.7.0 Add support for MD RAID0 mappings.
|
2017-02-28 06:29:36 +08:00
|
|
|
1.8.0 Explicitly check for compatible flags in the superblock metadata
|
2016-06-14 07:46:01 +08:00
|
|
|
and reject to start the raid set if any are set by a newer
|
|
|
|
target version, thus avoiding data corruption on a raid set
|
|
|
|
with a reshape in progress.
|
|
|
|
1.9.0 Add support for RAID level takeover/reshape/region size
|
|
|
|
and set size reduction.
|
2016-10-18 03:20:07 +08:00
|
|
|
1.9.1 Fix activation of existing RAID 4/10 mapped devices
|
2017-01-14 10:53:07 +08:00
|
|
|
1.9.2 Don't emit '- -' on the status table line in case the constructor
|
|
|
|
fails reading a superblock. Correctly emit 'maj:min1 maj:min2' and
|
|
|
|
'D' on the status line. If '- -' is passed into the constructor, emit
|
|
|
|
'- -' on the table line and '-' as the status line health character.
|
2016-12-01 05:31:05 +08:00
|
|
|
1.10.0 Add support for raid4/5/6 journal device
|
2017-03-18 08:39:12 +08:00
|
|
|
1.10.1 Fix data corruption on reshape request
|
|
|
|
1.11.0 Fix table line argument order
|
|
|
|
(wrong raid10_copies/raid10_format sequence)
|
2017-03-23 00:44:38 +08:00
|
|
|
1.11.1 Add raid4/5/6 journal write-back support via journal_mode option
|
2017-12-04 23:26:21 +08:00
|
|
|
1.12.1 Fix for MD deadlock between mddev_suspend() and md_write_start() available
|
2017-10-03 06:17:35 +08:00
|
|
|
1.13.0 Fix dev_health status at end of "recover" (was 'a', now 'A')
|
2017-12-04 23:26:21 +08:00
|
|
|
1.13.1 Fix deadlock caused by early md_stop_writes(). Also fix size an
|
|
|
|
state races.
|
2017-12-14 00:13:18 +08:00
|
|
|
1.13.2 Fix raid redundancy validation and avoid keeping raid set frozen
|