OpenCloudOS-Kernel/drivers/i2c/busses/i2c-stm32f7.c

2495 lines
65 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
/*
* Driver for STMicroelectronics STM32F7 I2C controller
*
* This I2C controller is described in the STM32F75xxx and STM32F74xxx Soc
* reference manual.
* Please see below a link to the documentation:
* http://www.st.com/resource/en/reference_manual/dm00124865.pdf
*
* Copyright (C) M'boumba Cedric Madianga 2017
* Copyright (C) STMicroelectronics 2017
* Author: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
*
* This driver is based on i2c-stm32f4.c
*
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/i2c-smbus.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pm_runtime.h>
#include <linux/pm_wakeirq.h>
#include <linux/regmap.h>
#include <linux/reset.h>
#include <linux/slab.h>
#include "i2c-stm32.h"
/* STM32F7 I2C registers */
#define STM32F7_I2C_CR1 0x00
#define STM32F7_I2C_CR2 0x04
#define STM32F7_I2C_OAR1 0x08
#define STM32F7_I2C_OAR2 0x0C
#define STM32F7_I2C_PECR 0x20
#define STM32F7_I2C_TIMINGR 0x10
#define STM32F7_I2C_ISR 0x18
#define STM32F7_I2C_ICR 0x1C
#define STM32F7_I2C_RXDR 0x24
#define STM32F7_I2C_TXDR 0x28
/* STM32F7 I2C control 1 */
#define STM32F7_I2C_CR1_PECEN BIT(23)
#define STM32F7_I2C_CR1_ALERTEN BIT(22)
#define STM32F7_I2C_CR1_SMBHEN BIT(20)
#define STM32F7_I2C_CR1_WUPEN BIT(18)
#define STM32F7_I2C_CR1_SBC BIT(16)
#define STM32F7_I2C_CR1_RXDMAEN BIT(15)
#define STM32F7_I2C_CR1_TXDMAEN BIT(14)
#define STM32F7_I2C_CR1_ANFOFF BIT(12)
#define STM32F7_I2C_CR1_DNF_MASK GENMASK(11, 8)
#define STM32F7_I2C_CR1_DNF(n) (((n) & 0xf) << 8)
#define STM32F7_I2C_CR1_ERRIE BIT(7)
#define STM32F7_I2C_CR1_TCIE BIT(6)
#define STM32F7_I2C_CR1_STOPIE BIT(5)
#define STM32F7_I2C_CR1_NACKIE BIT(4)
#define STM32F7_I2C_CR1_ADDRIE BIT(3)
#define STM32F7_I2C_CR1_RXIE BIT(2)
#define STM32F7_I2C_CR1_TXIE BIT(1)
#define STM32F7_I2C_CR1_PE BIT(0)
#define STM32F7_I2C_ALL_IRQ_MASK (STM32F7_I2C_CR1_ERRIE \
| STM32F7_I2C_CR1_TCIE \
| STM32F7_I2C_CR1_STOPIE \
| STM32F7_I2C_CR1_NACKIE \
| STM32F7_I2C_CR1_RXIE \
| STM32F7_I2C_CR1_TXIE)
#define STM32F7_I2C_XFER_IRQ_MASK (STM32F7_I2C_CR1_TCIE \
| STM32F7_I2C_CR1_STOPIE \
| STM32F7_I2C_CR1_NACKIE \
| STM32F7_I2C_CR1_RXIE \
| STM32F7_I2C_CR1_TXIE)
/* STM32F7 I2C control 2 */
#define STM32F7_I2C_CR2_PECBYTE BIT(26)
#define STM32F7_I2C_CR2_RELOAD BIT(24)
#define STM32F7_I2C_CR2_NBYTES_MASK GENMASK(23, 16)
#define STM32F7_I2C_CR2_NBYTES(n) (((n) & 0xff) << 16)
#define STM32F7_I2C_CR2_NACK BIT(15)
#define STM32F7_I2C_CR2_STOP BIT(14)
#define STM32F7_I2C_CR2_START BIT(13)
#define STM32F7_I2C_CR2_HEAD10R BIT(12)
#define STM32F7_I2C_CR2_ADD10 BIT(11)
#define STM32F7_I2C_CR2_RD_WRN BIT(10)
#define STM32F7_I2C_CR2_SADD10_MASK GENMASK(9, 0)
#define STM32F7_I2C_CR2_SADD10(n) (((n) & \
STM32F7_I2C_CR2_SADD10_MASK))
#define STM32F7_I2C_CR2_SADD7_MASK GENMASK(7, 1)
#define STM32F7_I2C_CR2_SADD7(n) (((n) & 0x7f) << 1)
/* STM32F7 I2C Own Address 1 */
#define STM32F7_I2C_OAR1_OA1EN BIT(15)
#define STM32F7_I2C_OAR1_OA1MODE BIT(10)
#define STM32F7_I2C_OAR1_OA1_10_MASK GENMASK(9, 0)
#define STM32F7_I2C_OAR1_OA1_10(n) (((n) & \
STM32F7_I2C_OAR1_OA1_10_MASK))
#define STM32F7_I2C_OAR1_OA1_7_MASK GENMASK(7, 1)
#define STM32F7_I2C_OAR1_OA1_7(n) (((n) & 0x7f) << 1)
#define STM32F7_I2C_OAR1_MASK (STM32F7_I2C_OAR1_OA1_7_MASK \
| STM32F7_I2C_OAR1_OA1_10_MASK \
| STM32F7_I2C_OAR1_OA1EN \
| STM32F7_I2C_OAR1_OA1MODE)
/* STM32F7 I2C Own Address 2 */
#define STM32F7_I2C_OAR2_OA2EN BIT(15)
#define STM32F7_I2C_OAR2_OA2MSK_MASK GENMASK(10, 8)
#define STM32F7_I2C_OAR2_OA2MSK(n) (((n) & 0x7) << 8)
#define STM32F7_I2C_OAR2_OA2_7_MASK GENMASK(7, 1)
#define STM32F7_I2C_OAR2_OA2_7(n) (((n) & 0x7f) << 1)
#define STM32F7_I2C_OAR2_MASK (STM32F7_I2C_OAR2_OA2MSK_MASK \
| STM32F7_I2C_OAR2_OA2_7_MASK \
| STM32F7_I2C_OAR2_OA2EN)
/* STM32F7 I2C Interrupt Status */
#define STM32F7_I2C_ISR_ADDCODE_MASK GENMASK(23, 17)
#define STM32F7_I2C_ISR_ADDCODE_GET(n) \
(((n) & STM32F7_I2C_ISR_ADDCODE_MASK) >> 17)
#define STM32F7_I2C_ISR_DIR BIT(16)
#define STM32F7_I2C_ISR_BUSY BIT(15)
#define STM32F7_I2C_ISR_ALERT BIT(13)
#define STM32F7_I2C_ISR_PECERR BIT(11)
#define STM32F7_I2C_ISR_ARLO BIT(9)
#define STM32F7_I2C_ISR_BERR BIT(8)
#define STM32F7_I2C_ISR_TCR BIT(7)
#define STM32F7_I2C_ISR_TC BIT(6)
#define STM32F7_I2C_ISR_STOPF BIT(5)
#define STM32F7_I2C_ISR_NACKF BIT(4)
#define STM32F7_I2C_ISR_ADDR BIT(3)
#define STM32F7_I2C_ISR_RXNE BIT(2)
#define STM32F7_I2C_ISR_TXIS BIT(1)
#define STM32F7_I2C_ISR_TXE BIT(0)
/* STM32F7 I2C Interrupt Clear */
#define STM32F7_I2C_ICR_ALERTCF BIT(13)
#define STM32F7_I2C_ICR_PECCF BIT(11)
#define STM32F7_I2C_ICR_ARLOCF BIT(9)
#define STM32F7_I2C_ICR_BERRCF BIT(8)
#define STM32F7_I2C_ICR_STOPCF BIT(5)
#define STM32F7_I2C_ICR_NACKCF BIT(4)
#define STM32F7_I2C_ICR_ADDRCF BIT(3)
/* STM32F7 I2C Timing */
#define STM32F7_I2C_TIMINGR_PRESC(n) (((n) & 0xf) << 28)
#define STM32F7_I2C_TIMINGR_SCLDEL(n) (((n) & 0xf) << 20)
#define STM32F7_I2C_TIMINGR_SDADEL(n) (((n) & 0xf) << 16)
#define STM32F7_I2C_TIMINGR_SCLH(n) (((n) & 0xff) << 8)
#define STM32F7_I2C_TIMINGR_SCLL(n) ((n) & 0xff)
#define STM32F7_I2C_MAX_LEN 0xff
#define STM32F7_I2C_DMA_LEN_MIN 0x16
enum {
STM32F7_SLAVE_HOSTNOTIFY,
STM32F7_SLAVE_7_10_BITS_ADDR,
STM32F7_SLAVE_7_BITS_ADDR,
STM32F7_I2C_MAX_SLAVE
};
#define STM32F7_I2C_DNF_DEFAULT 0
#define STM32F7_I2C_DNF_MAX 15
#define STM32F7_I2C_ANALOG_FILTER_DELAY_MIN 50 /* ns */
#define STM32F7_I2C_ANALOG_FILTER_DELAY_MAX 260 /* ns */
#define STM32F7_I2C_RISE_TIME_DEFAULT 25 /* ns */
#define STM32F7_I2C_FALL_TIME_DEFAULT 10 /* ns */
#define STM32F7_PRESC_MAX BIT(4)
#define STM32F7_SCLDEL_MAX BIT(4)
#define STM32F7_SDADEL_MAX BIT(4)
#define STM32F7_SCLH_MAX BIT(8)
#define STM32F7_SCLL_MAX BIT(8)
#define STM32F7_AUTOSUSPEND_DELAY (HZ / 100)
/**
* struct stm32f7_i2c_regs - i2c f7 registers backup
* @cr1: Control register 1
* @cr2: Control register 2
* @oar1: Own address 1 register
* @oar2: Own address 2 register
* @tmgr: Timing register
*/
struct stm32f7_i2c_regs {
u32 cr1;
u32 cr2;
u32 oar1;
u32 oar2;
u32 tmgr;
};
/**
* struct stm32f7_i2c_spec - private i2c specification timing
* @rate: I2C bus speed (Hz)
* @fall_max: Max fall time of both SDA and SCL signals (ns)
* @rise_max: Max rise time of both SDA and SCL signals (ns)
* @hddat_min: Min data hold time (ns)
* @vddat_max: Max data valid time (ns)
* @sudat_min: Min data setup time (ns)
* @l_min: Min low period of the SCL clock (ns)
* @h_min: Min high period of the SCL clock (ns)
*/
struct stm32f7_i2c_spec {
u32 rate;
u32 fall_max;
u32 rise_max;
u32 hddat_min;
u32 vddat_max;
u32 sudat_min;
u32 l_min;
u32 h_min;
};
/**
* struct stm32f7_i2c_setup - private I2C timing setup parameters
* @speed_freq: I2C speed frequency (Hz)
* @clock_src: I2C clock source frequency (Hz)
* @rise_time: Rise time (ns)
* @fall_time: Fall time (ns)
* @fmp_clr_offset: Fast Mode Plus clear register offset from set register
*/
struct stm32f7_i2c_setup {
u32 speed_freq;
u32 clock_src;
u32 rise_time;
u32 fall_time;
u32 fmp_clr_offset;
};
/**
* struct stm32f7_i2c_timings - private I2C output parameters
* @node: List entry
* @presc: Prescaler value
* @scldel: Data setup time
* @sdadel: Data hold time
* @sclh: SCL high period (master mode)
* @scll: SCL low period (master mode)
*/
struct stm32f7_i2c_timings {
struct list_head node;
u8 presc;
u8 scldel;
u8 sdadel;
u8 sclh;
u8 scll;
};
/**
* struct stm32f7_i2c_msg - client specific data
* @addr: 8-bit or 10-bit slave addr, including r/w bit
* @count: number of bytes to be transferred
* @buf: data buffer
* @result: result of the transfer
* @stop: last I2C msg to be sent, i.e. STOP to be generated
* @smbus: boolean to know if the I2C IP is used in SMBus mode
* @size: type of SMBus protocol
* @read_write: direction of SMBus protocol
* SMBus block read and SMBus block write - block read process call protocols
* @smbus_buf: buffer to be used for SMBus protocol transfer. It will
* contain a maximum of 32 bytes of data + byte command + byte count + PEC
* This buffer has to be 32-bit aligned to be compliant with memory address
* register in DMA mode.
*/
struct stm32f7_i2c_msg {
u16 addr;
u32 count;
u8 *buf;
int result;
bool stop;
bool smbus;
int size;
char read_write;
u8 smbus_buf[I2C_SMBUS_BLOCK_MAX + 3] __aligned(4);
};
/**
* struct stm32f7_i2c_alert - SMBus alert specific data
* @setup: platform data for the smbus_alert i2c client
* @ara: I2C slave device used to respond to the SMBus Alert with Alert
* Response Address
*/
struct stm32f7_i2c_alert {
struct i2c_smbus_alert_setup setup;
struct i2c_client *ara;
};
/**
* struct stm32f7_i2c_dev - private data of the controller
* @adap: I2C adapter for this controller
* @dev: device for this controller
* @base: virtual memory area
* @complete: completion of I2C message
* @clk: hw i2c clock
* @bus_rate: I2C clock frequency of the controller
* @msg: Pointer to data to be written
* @msg_num: number of I2C messages to be executed
* @msg_id: message identifiant
* @f7_msg: customized i2c msg for driver usage
* @setup: I2C timing input setup
* @timing: I2C computed timings
* @slave: list of slave devices registered on the I2C bus
* @slave_running: slave device currently used
* @backup_regs: backup of i2c controller registers (for suspend/resume)
* @slave_dir: transfer direction for the current slave device
* @master_mode: boolean to know in which mode the I2C is running (master or
* slave)
* @dma: dma data
* @use_dma: boolean to know if dma is used in the current transfer
* @regmap: holds SYSCFG phandle for Fast Mode Plus bits
* @fmp_sreg: register address for setting Fast Mode Plus bits
* @fmp_creg: register address for clearing Fast Mode Plus bits
* @fmp_mask: mask for Fast Mode Plus bits in set register
* @wakeup_src: boolean to know if the device is a wakeup source
* @smbus_mode: states that the controller is configured in SMBus mode
* @host_notify_client: SMBus host-notify client
* @analog_filter: boolean to indicate enabling of the analog filter
* @dnf_dt: value of digital filter requested via dt
* @dnf: value of digital filter to apply
* @alert: SMBus alert specific data
*/
struct stm32f7_i2c_dev {
struct i2c_adapter adap;
struct device *dev;
void __iomem *base;
struct completion complete;
struct clk *clk;
unsigned int bus_rate;
struct i2c_msg *msg;
unsigned int msg_num;
unsigned int msg_id;
struct stm32f7_i2c_msg f7_msg;
struct stm32f7_i2c_setup setup;
struct stm32f7_i2c_timings timing;
struct i2c_client *slave[STM32F7_I2C_MAX_SLAVE];
struct i2c_client *slave_running;
struct stm32f7_i2c_regs backup_regs;
u32 slave_dir;
bool master_mode;
struct stm32_i2c_dma *dma;
bool use_dma;
struct regmap *regmap;
u32 fmp_sreg;
u32 fmp_creg;
u32 fmp_mask;
bool wakeup_src;
bool smbus_mode;
struct i2c_client *host_notify_client;
bool analog_filter;
u32 dnf_dt;
u32 dnf;
struct stm32f7_i2c_alert *alert;
};
/*
* All these values are coming from I2C Specification, Version 6.0, 4th of
* April 2014.
*
* Table10. Characteristics of the SDA and SCL bus lines for Standard, Fast,
* and Fast-mode Plus I2C-bus devices
*/
static struct stm32f7_i2c_spec stm32f7_i2c_specs[] = {
{
.rate = I2C_MAX_STANDARD_MODE_FREQ,
.fall_max = 300,
.rise_max = 1000,
.hddat_min = 0,
.vddat_max = 3450,
.sudat_min = 250,
.l_min = 4700,
.h_min = 4000,
},
{
.rate = I2C_MAX_FAST_MODE_FREQ,
.fall_max = 300,
.rise_max = 300,
.hddat_min = 0,
.vddat_max = 900,
.sudat_min = 100,
.l_min = 1300,
.h_min = 600,
},
{
.rate = I2C_MAX_FAST_MODE_PLUS_FREQ,
.fall_max = 100,
.rise_max = 120,
.hddat_min = 0,
.vddat_max = 450,
.sudat_min = 50,
.l_min = 500,
.h_min = 260,
},
};
static const struct stm32f7_i2c_setup stm32f7_setup = {
.rise_time = STM32F7_I2C_RISE_TIME_DEFAULT,
.fall_time = STM32F7_I2C_FALL_TIME_DEFAULT,
};
static const struct stm32f7_i2c_setup stm32mp15_setup = {
.rise_time = STM32F7_I2C_RISE_TIME_DEFAULT,
.fall_time = STM32F7_I2C_FALL_TIME_DEFAULT,
.fmp_clr_offset = 0x40,
};
static const struct stm32f7_i2c_setup stm32mp13_setup = {
.rise_time = STM32F7_I2C_RISE_TIME_DEFAULT,
.fall_time = STM32F7_I2C_FALL_TIME_DEFAULT,
.fmp_clr_offset = 0x4,
};
static inline void stm32f7_i2c_set_bits(void __iomem *reg, u32 mask)
{
writel_relaxed(readl_relaxed(reg) | mask, reg);
}
static inline void stm32f7_i2c_clr_bits(void __iomem *reg, u32 mask)
{
writel_relaxed(readl_relaxed(reg) & ~mask, reg);
}
static void stm32f7_i2c_disable_irq(struct stm32f7_i2c_dev *i2c_dev, u32 mask)
{
stm32f7_i2c_clr_bits(i2c_dev->base + STM32F7_I2C_CR1, mask);
}
static struct stm32f7_i2c_spec *stm32f7_get_specs(u32 rate)
{
int i;
for (i = 0; i < ARRAY_SIZE(stm32f7_i2c_specs); i++)
if (rate <= stm32f7_i2c_specs[i].rate)
return &stm32f7_i2c_specs[i];
return ERR_PTR(-EINVAL);
}
#define RATE_MIN(rate) ((rate) * 8 / 10)
static int stm32f7_i2c_compute_timing(struct stm32f7_i2c_dev *i2c_dev,
struct stm32f7_i2c_setup *setup,
struct stm32f7_i2c_timings *output)
{
struct stm32f7_i2c_spec *specs;
u32 p_prev = STM32F7_PRESC_MAX;
u32 i2cclk = DIV_ROUND_CLOSEST(NSEC_PER_SEC,
setup->clock_src);
u32 i2cbus = DIV_ROUND_CLOSEST(NSEC_PER_SEC,
setup->speed_freq);
u32 clk_error_prev = i2cbus;
u32 tsync;
u32 af_delay_min, af_delay_max;
u32 dnf_delay;
u32 clk_min, clk_max;
int sdadel_min, sdadel_max;
int scldel_min;
struct stm32f7_i2c_timings *v, *_v, *s;
struct list_head solutions;
u16 p, l, a, h;
int ret = 0;
specs = stm32f7_get_specs(setup->speed_freq);
if (specs == ERR_PTR(-EINVAL)) {
dev_err(i2c_dev->dev, "speed out of bound {%d}\n",
setup->speed_freq);
return -EINVAL;
}
if ((setup->rise_time > specs->rise_max) ||
(setup->fall_time > specs->fall_max)) {
dev_err(i2c_dev->dev,
"timings out of bound Rise{%d>%d}/Fall{%d>%d}\n",
setup->rise_time, specs->rise_max,
setup->fall_time, specs->fall_max);
return -EINVAL;
}
i2c_dev->dnf = DIV_ROUND_CLOSEST(i2c_dev->dnf_dt, i2cclk);
if (i2c_dev->dnf > STM32F7_I2C_DNF_MAX) {
dev_err(i2c_dev->dev,
"DNF out of bound %d/%d\n",
i2c_dev->dnf * i2cclk, STM32F7_I2C_DNF_MAX * i2cclk);
return -EINVAL;
}
/* Analog and Digital Filters */
af_delay_min =
(i2c_dev->analog_filter ?
STM32F7_I2C_ANALOG_FILTER_DELAY_MIN : 0);
af_delay_max =
(i2c_dev->analog_filter ?
STM32F7_I2C_ANALOG_FILTER_DELAY_MAX : 0);
dnf_delay = i2c_dev->dnf * i2cclk;
sdadel_min = specs->hddat_min + setup->fall_time -
af_delay_min - (i2c_dev->dnf + 3) * i2cclk;
sdadel_max = specs->vddat_max - setup->rise_time -
af_delay_max - (i2c_dev->dnf + 4) * i2cclk;
scldel_min = setup->rise_time + specs->sudat_min;
if (sdadel_min < 0)
sdadel_min = 0;
if (sdadel_max < 0)
sdadel_max = 0;
dev_dbg(i2c_dev->dev, "SDADEL(min/max): %i/%i, SCLDEL(Min): %i\n",
sdadel_min, sdadel_max, scldel_min);
INIT_LIST_HEAD(&solutions);
/* Compute possible values for PRESC, SCLDEL and SDADEL */
for (p = 0; p < STM32F7_PRESC_MAX; p++) {
for (l = 0; l < STM32F7_SCLDEL_MAX; l++) {
u32 scldel = (l + 1) * (p + 1) * i2cclk;
if (scldel < scldel_min)
continue;
for (a = 0; a < STM32F7_SDADEL_MAX; a++) {
u32 sdadel = (a * (p + 1) + 1) * i2cclk;
if (((sdadel >= sdadel_min) &&
(sdadel <= sdadel_max)) &&
(p != p_prev)) {
v = kmalloc(sizeof(*v), GFP_KERNEL);
if (!v) {
ret = -ENOMEM;
goto exit;
}
v->presc = p;
v->scldel = l;
v->sdadel = a;
p_prev = p;
list_add_tail(&v->node,
&solutions);
break;
}
}
if (p_prev == p)
break;
}
}
if (list_empty(&solutions)) {
dev_err(i2c_dev->dev, "no Prescaler solution\n");
ret = -EPERM;
goto exit;
}
tsync = af_delay_min + dnf_delay + (2 * i2cclk);
s = NULL;
clk_max = NSEC_PER_SEC / RATE_MIN(setup->speed_freq);
clk_min = NSEC_PER_SEC / setup->speed_freq;
/*
* Among Prescaler possibilities discovered above figures out SCL Low
* and High Period. Provided:
* - SCL Low Period has to be higher than SCL Clock Low Period
* defined by I2C Specification. I2C Clock has to be lower than
* (SCL Low Period - Analog/Digital filters) / 4.
* - SCL High Period has to be lower than SCL Clock High Period
* defined by I2C Specification
* - I2C Clock has to be lower than SCL High Period
*/
list_for_each_entry(v, &solutions, node) {
u32 prescaler = (v->presc + 1) * i2cclk;
for (l = 0; l < STM32F7_SCLL_MAX; l++) {
u32 tscl_l = (l + 1) * prescaler + tsync;
if ((tscl_l < specs->l_min) ||
(i2cclk >=
((tscl_l - af_delay_min - dnf_delay) / 4))) {
continue;
}
for (h = 0; h < STM32F7_SCLH_MAX; h++) {
u32 tscl_h = (h + 1) * prescaler + tsync;
u32 tscl = tscl_l + tscl_h +
setup->rise_time + setup->fall_time;
if ((tscl >= clk_min) && (tscl <= clk_max) &&
(tscl_h >= specs->h_min) &&
(i2cclk < tscl_h)) {
int clk_error = tscl - i2cbus;
if (clk_error < 0)
clk_error = -clk_error;
if (clk_error < clk_error_prev) {
clk_error_prev = clk_error;
v->scll = l;
v->sclh = h;
s = v;
}
}
}
}
}
if (!s) {
dev_err(i2c_dev->dev, "no solution at all\n");
ret = -EPERM;
goto exit;
}
output->presc = s->presc;
output->scldel = s->scldel;
output->sdadel = s->sdadel;
output->scll = s->scll;
output->sclh = s->sclh;
dev_dbg(i2c_dev->dev,
"Presc: %i, scldel: %i, sdadel: %i, scll: %i, sclh: %i\n",
output->presc,
output->scldel, output->sdadel,
output->scll, output->sclh);
exit:
/* Release list and memory */
list_for_each_entry_safe(v, _v, &solutions, node) {
list_del(&v->node);
kfree(v);
}
return ret;
}
static u32 stm32f7_get_lower_rate(u32 rate)
{
int i = ARRAY_SIZE(stm32f7_i2c_specs);
while (--i)
if (stm32f7_i2c_specs[i].rate < rate)
break;
return stm32f7_i2c_specs[i].rate;
}
static int stm32f7_i2c_setup_timing(struct stm32f7_i2c_dev *i2c_dev,
struct stm32f7_i2c_setup *setup)
{
struct i2c_timings timings, *t = &timings;
int ret = 0;
t->bus_freq_hz = I2C_MAX_STANDARD_MODE_FREQ;
t->scl_rise_ns = i2c_dev->setup.rise_time;
t->scl_fall_ns = i2c_dev->setup.fall_time;
i2c_parse_fw_timings(i2c_dev->dev, t, false);
if (t->bus_freq_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) {
dev_err(i2c_dev->dev, "Invalid bus speed (%i>%i)\n",
t->bus_freq_hz, I2C_MAX_FAST_MODE_PLUS_FREQ);
return -EINVAL;
}
setup->speed_freq = t->bus_freq_hz;
i2c_dev->setup.rise_time = t->scl_rise_ns;
i2c_dev->setup.fall_time = t->scl_fall_ns;
i2c_dev->dnf_dt = t->digital_filter_width_ns;
setup->clock_src = clk_get_rate(i2c_dev->clk);
if (!setup->clock_src) {
dev_err(i2c_dev->dev, "clock rate is 0\n");
return -EINVAL;
}
if (!of_property_read_bool(i2c_dev->dev->of_node, "i2c-digital-filter"))
i2c_dev->dnf_dt = STM32F7_I2C_DNF_DEFAULT;
do {
ret = stm32f7_i2c_compute_timing(i2c_dev, setup,
&i2c_dev->timing);
if (ret) {
dev_err(i2c_dev->dev,
"failed to compute I2C timings.\n");
if (setup->speed_freq <= I2C_MAX_STANDARD_MODE_FREQ)
break;
setup->speed_freq =
stm32f7_get_lower_rate(setup->speed_freq);
dev_warn(i2c_dev->dev,
"downgrade I2C Speed Freq to (%i)\n",
setup->speed_freq);
}
} while (ret);
if (ret) {
dev_err(i2c_dev->dev, "Impossible to compute I2C timings.\n");
return ret;
}
i2c_dev->analog_filter = of_property_read_bool(i2c_dev->dev->of_node,
"i2c-analog-filter");
dev_dbg(i2c_dev->dev, "I2C Speed(%i), Clk Source(%i)\n",
setup->speed_freq, setup->clock_src);
dev_dbg(i2c_dev->dev, "I2C Rise(%i) and Fall(%i) Time\n",
setup->rise_time, setup->fall_time);
dev_dbg(i2c_dev->dev, "I2C Analog Filter(%s), DNF(%i)\n",
(i2c_dev->analog_filter ? "On" : "Off"), i2c_dev->dnf);
i2c_dev->bus_rate = setup->speed_freq;
return 0;
}
static void stm32f7_i2c_disable_dma_req(struct stm32f7_i2c_dev *i2c_dev)
{
void __iomem *base = i2c_dev->base;
u32 mask = STM32F7_I2C_CR1_RXDMAEN | STM32F7_I2C_CR1_TXDMAEN;
stm32f7_i2c_clr_bits(base + STM32F7_I2C_CR1, mask);
}
static void stm32f7_i2c_dma_callback(void *arg)
{
struct stm32f7_i2c_dev *i2c_dev = (struct stm32f7_i2c_dev *)arg;
struct stm32_i2c_dma *dma = i2c_dev->dma;
struct device *dev = dma->chan_using->device->dev;
stm32f7_i2c_disable_dma_req(i2c_dev);
dma_unmap_single(dev, dma->dma_buf, dma->dma_len, dma->dma_data_dir);
complete(&dma->dma_complete);
}
static void stm32f7_i2c_hw_config(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_timings *t = &i2c_dev->timing;
u32 timing = 0;
/* Timing settings */
timing |= STM32F7_I2C_TIMINGR_PRESC(t->presc);
timing |= STM32F7_I2C_TIMINGR_SCLDEL(t->scldel);
timing |= STM32F7_I2C_TIMINGR_SDADEL(t->sdadel);
timing |= STM32F7_I2C_TIMINGR_SCLH(t->sclh);
timing |= STM32F7_I2C_TIMINGR_SCLL(t->scll);
writel_relaxed(timing, i2c_dev->base + STM32F7_I2C_TIMINGR);
/* Configure the Analog Filter */
if (i2c_dev->analog_filter)
stm32f7_i2c_clr_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_ANFOFF);
else
stm32f7_i2c_set_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_ANFOFF);
/* Program the Digital Filter */
stm32f7_i2c_clr_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_DNF_MASK);
stm32f7_i2c_set_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_DNF(i2c_dev->dnf));
stm32f7_i2c_set_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_PE);
}
static void stm32f7_i2c_write_tx_data(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
void __iomem *base = i2c_dev->base;
if (f7_msg->count) {
writeb_relaxed(*f7_msg->buf++, base + STM32F7_I2C_TXDR);
f7_msg->count--;
}
}
static void stm32f7_i2c_read_rx_data(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
void __iomem *base = i2c_dev->base;
if (f7_msg->count) {
*f7_msg->buf++ = readb_relaxed(base + STM32F7_I2C_RXDR);
f7_msg->count--;
} else {
/* Flush RX buffer has no data is expected */
readb_relaxed(base + STM32F7_I2C_RXDR);
}
}
static void stm32f7_i2c_reload(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
u32 cr2;
if (i2c_dev->use_dma)
f7_msg->count -= STM32F7_I2C_MAX_LEN;
cr2 = readl_relaxed(i2c_dev->base + STM32F7_I2C_CR2);
cr2 &= ~STM32F7_I2C_CR2_NBYTES_MASK;
if (f7_msg->count > STM32F7_I2C_MAX_LEN) {
cr2 |= STM32F7_I2C_CR2_NBYTES(STM32F7_I2C_MAX_LEN);
} else {
cr2 &= ~STM32F7_I2C_CR2_RELOAD;
cr2 |= STM32F7_I2C_CR2_NBYTES(f7_msg->count);
}
writel_relaxed(cr2, i2c_dev->base + STM32F7_I2C_CR2);
}
static void stm32f7_i2c_smbus_reload(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
u32 cr2;
u8 *val;
/*
* For I2C_SMBUS_BLOCK_DATA && I2C_SMBUS_BLOCK_PROC_CALL, the first
* data received inform us how many data will follow.
*/
stm32f7_i2c_read_rx_data(i2c_dev);
/*
* Update NBYTES with the value read to continue the transfer
*/
val = f7_msg->buf - sizeof(u8);
f7_msg->count = *val;
cr2 = readl_relaxed(i2c_dev->base + STM32F7_I2C_CR2);
cr2 &= ~(STM32F7_I2C_CR2_NBYTES_MASK | STM32F7_I2C_CR2_RELOAD);
cr2 |= STM32F7_I2C_CR2_NBYTES(f7_msg->count);
writel_relaxed(cr2, i2c_dev->base + STM32F7_I2C_CR2);
}
static void stm32f7_i2c_release_bus(struct i2c_adapter *i2c_adap)
{
struct stm32f7_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
stm32f7_i2c_clr_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_PE);
stm32f7_i2c_hw_config(i2c_dev);
}
static int stm32f7_i2c_wait_free_bus(struct stm32f7_i2c_dev *i2c_dev)
{
u32 status;
int ret;
ret = readl_relaxed_poll_timeout(i2c_dev->base + STM32F7_I2C_ISR,
status,
!(status & STM32F7_I2C_ISR_BUSY),
10, 1000);
if (!ret)
return 0;
stm32f7_i2c_release_bus(&i2c_dev->adap);
return -EBUSY;
}
static void stm32f7_i2c_xfer_msg(struct stm32f7_i2c_dev *i2c_dev,
struct i2c_msg *msg)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
void __iomem *base = i2c_dev->base;
u32 cr1, cr2;
int ret;
f7_msg->addr = msg->addr;
f7_msg->buf = msg->buf;
f7_msg->count = msg->len;
f7_msg->result = 0;
f7_msg->stop = (i2c_dev->msg_id >= i2c_dev->msg_num - 1);
reinit_completion(&i2c_dev->complete);
cr1 = readl_relaxed(base + STM32F7_I2C_CR1);
cr2 = readl_relaxed(base + STM32F7_I2C_CR2);
/* Set transfer direction */
cr2 &= ~STM32F7_I2C_CR2_RD_WRN;
if (msg->flags & I2C_M_RD)
cr2 |= STM32F7_I2C_CR2_RD_WRN;
/* Set slave address */
cr2 &= ~(STM32F7_I2C_CR2_HEAD10R | STM32F7_I2C_CR2_ADD10);
if (msg->flags & I2C_M_TEN) {
cr2 &= ~STM32F7_I2C_CR2_SADD10_MASK;
cr2 |= STM32F7_I2C_CR2_SADD10(f7_msg->addr);
cr2 |= STM32F7_I2C_CR2_ADD10;
} else {
cr2 &= ~STM32F7_I2C_CR2_SADD7_MASK;
cr2 |= STM32F7_I2C_CR2_SADD7(f7_msg->addr);
}
/* Set nb bytes to transfer and reload if needed */
cr2 &= ~(STM32F7_I2C_CR2_NBYTES_MASK | STM32F7_I2C_CR2_RELOAD);
if (f7_msg->count > STM32F7_I2C_MAX_LEN) {
cr2 |= STM32F7_I2C_CR2_NBYTES(STM32F7_I2C_MAX_LEN);
cr2 |= STM32F7_I2C_CR2_RELOAD;
} else {
cr2 |= STM32F7_I2C_CR2_NBYTES(f7_msg->count);
}
/* Enable NACK, STOP, error and transfer complete interrupts */
cr1 |= STM32F7_I2C_CR1_ERRIE | STM32F7_I2C_CR1_TCIE |
STM32F7_I2C_CR1_STOPIE | STM32F7_I2C_CR1_NACKIE;
/* Clear DMA req and TX/RX interrupt */
cr1 &= ~(STM32F7_I2C_CR1_RXIE | STM32F7_I2C_CR1_TXIE |
STM32F7_I2C_CR1_RXDMAEN | STM32F7_I2C_CR1_TXDMAEN);
/* Configure DMA or enable RX/TX interrupt */
i2c_dev->use_dma = false;
if (i2c_dev->dma && f7_msg->count >= STM32F7_I2C_DMA_LEN_MIN) {
ret = stm32_i2c_prep_dma_xfer(i2c_dev->dev, i2c_dev->dma,
msg->flags & I2C_M_RD,
f7_msg->count, f7_msg->buf,
stm32f7_i2c_dma_callback,
i2c_dev);
if (!ret)
i2c_dev->use_dma = true;
else
dev_warn(i2c_dev->dev, "can't use DMA\n");
}
if (!i2c_dev->use_dma) {
if (msg->flags & I2C_M_RD)
cr1 |= STM32F7_I2C_CR1_RXIE;
else
cr1 |= STM32F7_I2C_CR1_TXIE;
} else {
if (msg->flags & I2C_M_RD)
cr1 |= STM32F7_I2C_CR1_RXDMAEN;
else
cr1 |= STM32F7_I2C_CR1_TXDMAEN;
}
/* Configure Start/Repeated Start */
cr2 |= STM32F7_I2C_CR2_START;
i2c_dev->master_mode = true;
/* Write configurations registers */
writel_relaxed(cr1, base + STM32F7_I2C_CR1);
writel_relaxed(cr2, base + STM32F7_I2C_CR2);
}
static int stm32f7_i2c_smbus_xfer_msg(struct stm32f7_i2c_dev *i2c_dev,
unsigned short flags, u8 command,
union i2c_smbus_data *data)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
struct device *dev = i2c_dev->dev;
void __iomem *base = i2c_dev->base;
u32 cr1, cr2;
int i, ret;
f7_msg->result = 0;
reinit_completion(&i2c_dev->complete);
cr2 = readl_relaxed(base + STM32F7_I2C_CR2);
cr1 = readl_relaxed(base + STM32F7_I2C_CR1);
/* Set transfer direction */
cr2 &= ~STM32F7_I2C_CR2_RD_WRN;
if (f7_msg->read_write)
cr2 |= STM32F7_I2C_CR2_RD_WRN;
/* Set slave address */
cr2 &= ~(STM32F7_I2C_CR2_ADD10 | STM32F7_I2C_CR2_SADD7_MASK);
cr2 |= STM32F7_I2C_CR2_SADD7(f7_msg->addr);
f7_msg->smbus_buf[0] = command;
switch (f7_msg->size) {
case I2C_SMBUS_QUICK:
f7_msg->stop = true;
f7_msg->count = 0;
break;
case I2C_SMBUS_BYTE:
f7_msg->stop = true;
f7_msg->count = 1;
break;
case I2C_SMBUS_BYTE_DATA:
if (f7_msg->read_write) {
f7_msg->stop = false;
f7_msg->count = 1;
cr2 &= ~STM32F7_I2C_CR2_RD_WRN;
} else {
f7_msg->stop = true;
f7_msg->count = 2;
f7_msg->smbus_buf[1] = data->byte;
}
break;
case I2C_SMBUS_WORD_DATA:
if (f7_msg->read_write) {
f7_msg->stop = false;
f7_msg->count = 1;
cr2 &= ~STM32F7_I2C_CR2_RD_WRN;
} else {
f7_msg->stop = true;
f7_msg->count = 3;
f7_msg->smbus_buf[1] = data->word & 0xff;
f7_msg->smbus_buf[2] = data->word >> 8;
}
break;
case I2C_SMBUS_BLOCK_DATA:
if (f7_msg->read_write) {
f7_msg->stop = false;
f7_msg->count = 1;
cr2 &= ~STM32F7_I2C_CR2_RD_WRN;
} else {
f7_msg->stop = true;
if (data->block[0] > I2C_SMBUS_BLOCK_MAX ||
!data->block[0]) {
dev_err(dev, "Invalid block write size %d\n",
data->block[0]);
return -EINVAL;
}
f7_msg->count = data->block[0] + 2;
for (i = 1; i < f7_msg->count; i++)
f7_msg->smbus_buf[i] = data->block[i - 1];
}
break;
case I2C_SMBUS_PROC_CALL:
f7_msg->stop = false;
f7_msg->count = 3;
f7_msg->smbus_buf[1] = data->word & 0xff;
f7_msg->smbus_buf[2] = data->word >> 8;
cr2 &= ~STM32F7_I2C_CR2_RD_WRN;
f7_msg->read_write = I2C_SMBUS_READ;
break;
case I2C_SMBUS_BLOCK_PROC_CALL:
f7_msg->stop = false;
if (data->block[0] > I2C_SMBUS_BLOCK_MAX - 1) {
dev_err(dev, "Invalid block write size %d\n",
data->block[0]);
return -EINVAL;
}
f7_msg->count = data->block[0] + 2;
for (i = 1; i < f7_msg->count; i++)
f7_msg->smbus_buf[i] = data->block[i - 1];
cr2 &= ~STM32F7_I2C_CR2_RD_WRN;
f7_msg->read_write = I2C_SMBUS_READ;
break;
case I2C_SMBUS_I2C_BLOCK_DATA:
/* Rely on emulated i2c transfer (through master_xfer) */
return -EOPNOTSUPP;
default:
dev_err(dev, "Unsupported smbus protocol %d\n", f7_msg->size);
return -EOPNOTSUPP;
}
f7_msg->buf = f7_msg->smbus_buf;
/* Configure PEC */
if ((flags & I2C_CLIENT_PEC) && f7_msg->size != I2C_SMBUS_QUICK) {
cr1 |= STM32F7_I2C_CR1_PECEN;
cr2 |= STM32F7_I2C_CR2_PECBYTE;
if (!f7_msg->read_write)
f7_msg->count++;
} else {
cr1 &= ~STM32F7_I2C_CR1_PECEN;
cr2 &= ~STM32F7_I2C_CR2_PECBYTE;
}
/* Set number of bytes to be transferred */
cr2 &= ~(STM32F7_I2C_CR2_NBYTES_MASK | STM32F7_I2C_CR2_RELOAD);
cr2 |= STM32F7_I2C_CR2_NBYTES(f7_msg->count);
/* Enable NACK, STOP, error and transfer complete interrupts */
cr1 |= STM32F7_I2C_CR1_ERRIE | STM32F7_I2C_CR1_TCIE |
STM32F7_I2C_CR1_STOPIE | STM32F7_I2C_CR1_NACKIE;
/* Clear DMA req and TX/RX interrupt */
cr1 &= ~(STM32F7_I2C_CR1_RXIE | STM32F7_I2C_CR1_TXIE |
STM32F7_I2C_CR1_RXDMAEN | STM32F7_I2C_CR1_TXDMAEN);
/* Configure DMA or enable RX/TX interrupt */
i2c_dev->use_dma = false;
if (i2c_dev->dma && f7_msg->count >= STM32F7_I2C_DMA_LEN_MIN) {
ret = stm32_i2c_prep_dma_xfer(i2c_dev->dev, i2c_dev->dma,
cr2 & STM32F7_I2C_CR2_RD_WRN,
f7_msg->count, f7_msg->buf,
stm32f7_i2c_dma_callback,
i2c_dev);
if (!ret)
i2c_dev->use_dma = true;
else
dev_warn(i2c_dev->dev, "can't use DMA\n");
}
if (!i2c_dev->use_dma) {
if (cr2 & STM32F7_I2C_CR2_RD_WRN)
cr1 |= STM32F7_I2C_CR1_RXIE;
else
cr1 |= STM32F7_I2C_CR1_TXIE;
} else {
if (cr2 & STM32F7_I2C_CR2_RD_WRN)
cr1 |= STM32F7_I2C_CR1_RXDMAEN;
else
cr1 |= STM32F7_I2C_CR1_TXDMAEN;
}
/* Set Start bit */
cr2 |= STM32F7_I2C_CR2_START;
i2c_dev->master_mode = true;
/* Write configurations registers */
writel_relaxed(cr1, base + STM32F7_I2C_CR1);
writel_relaxed(cr2, base + STM32F7_I2C_CR2);
return 0;
}
static void stm32f7_i2c_smbus_rep_start(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
void __iomem *base = i2c_dev->base;
u32 cr1, cr2;
int ret;
cr2 = readl_relaxed(base + STM32F7_I2C_CR2);
cr1 = readl_relaxed(base + STM32F7_I2C_CR1);
/* Set transfer direction */
cr2 |= STM32F7_I2C_CR2_RD_WRN;
switch (f7_msg->size) {
case I2C_SMBUS_BYTE_DATA:
f7_msg->count = 1;
break;
case I2C_SMBUS_WORD_DATA:
case I2C_SMBUS_PROC_CALL:
f7_msg->count = 2;
break;
case I2C_SMBUS_BLOCK_DATA:
case I2C_SMBUS_BLOCK_PROC_CALL:
f7_msg->count = 1;
cr2 |= STM32F7_I2C_CR2_RELOAD;
break;
}
f7_msg->buf = f7_msg->smbus_buf;
f7_msg->stop = true;
/* Add one byte for PEC if needed */
if (cr1 & STM32F7_I2C_CR1_PECEN)
f7_msg->count++;
/* Set number of bytes to be transferred */
cr2 &= ~(STM32F7_I2C_CR2_NBYTES_MASK);
cr2 |= STM32F7_I2C_CR2_NBYTES(f7_msg->count);
/*
* Configure RX/TX interrupt:
*/
cr1 &= ~(STM32F7_I2C_CR1_RXIE | STM32F7_I2C_CR1_TXIE);
cr1 |= STM32F7_I2C_CR1_RXIE;
/*
* Configure DMA or enable RX/TX interrupt:
* For I2C_SMBUS_BLOCK_DATA and I2C_SMBUS_BLOCK_PROC_CALL we don't use
* dma as we don't know in advance how many data will be received
*/
cr1 &= ~(STM32F7_I2C_CR1_RXIE | STM32F7_I2C_CR1_TXIE |
STM32F7_I2C_CR1_RXDMAEN | STM32F7_I2C_CR1_TXDMAEN);
i2c_dev->use_dma = false;
if (i2c_dev->dma && f7_msg->count >= STM32F7_I2C_DMA_LEN_MIN &&
f7_msg->size != I2C_SMBUS_BLOCK_DATA &&
f7_msg->size != I2C_SMBUS_BLOCK_PROC_CALL) {
ret = stm32_i2c_prep_dma_xfer(i2c_dev->dev, i2c_dev->dma,
cr2 & STM32F7_I2C_CR2_RD_WRN,
f7_msg->count, f7_msg->buf,
stm32f7_i2c_dma_callback,
i2c_dev);
if (!ret)
i2c_dev->use_dma = true;
else
dev_warn(i2c_dev->dev, "can't use DMA\n");
}
if (!i2c_dev->use_dma)
cr1 |= STM32F7_I2C_CR1_RXIE;
else
cr1 |= STM32F7_I2C_CR1_RXDMAEN;
/* Configure Repeated Start */
cr2 |= STM32F7_I2C_CR2_START;
/* Write configurations registers */
writel_relaxed(cr1, base + STM32F7_I2C_CR1);
writel_relaxed(cr2, base + STM32F7_I2C_CR2);
}
static int stm32f7_i2c_smbus_check_pec(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
u8 count, internal_pec, received_pec;
internal_pec = readl_relaxed(i2c_dev->base + STM32F7_I2C_PECR);
switch (f7_msg->size) {
case I2C_SMBUS_BYTE:
case I2C_SMBUS_BYTE_DATA:
received_pec = f7_msg->smbus_buf[1];
break;
case I2C_SMBUS_WORD_DATA:
case I2C_SMBUS_PROC_CALL:
received_pec = f7_msg->smbus_buf[2];
break;
case I2C_SMBUS_BLOCK_DATA:
case I2C_SMBUS_BLOCK_PROC_CALL:
count = f7_msg->smbus_buf[0];
received_pec = f7_msg->smbus_buf[count];
break;
default:
dev_err(i2c_dev->dev, "Unsupported smbus protocol for PEC\n");
return -EINVAL;
}
if (internal_pec != received_pec) {
dev_err(i2c_dev->dev, "Bad PEC 0x%02x vs. 0x%02x\n",
internal_pec, received_pec);
return -EBADMSG;
}
return 0;
}
static bool stm32f7_i2c_is_addr_match(struct i2c_client *slave, u32 addcode)
{
u32 addr;
if (!slave)
return false;
if (slave->flags & I2C_CLIENT_TEN) {
/*
* For 10-bit addr, addcode = 11110XY with
* X = Bit 9 of slave address
* Y = Bit 8 of slave address
*/
addr = slave->addr >> 8;
addr |= 0x78;
if (addr == addcode)
return true;
} else {
addr = slave->addr & 0x7f;
if (addr == addcode)
return true;
}
return false;
}
static void stm32f7_i2c_slave_start(struct stm32f7_i2c_dev *i2c_dev)
{
struct i2c_client *slave = i2c_dev->slave_running;
void __iomem *base = i2c_dev->base;
u32 mask;
u8 value = 0;
if (i2c_dev->slave_dir) {
/* Notify i2c slave that new read transfer is starting */
i2c_slave_event(slave, I2C_SLAVE_READ_REQUESTED, &value);
/*
* Disable slave TX config in case of I2C combined message
* (I2C Write followed by I2C Read)
*/
mask = STM32F7_I2C_CR2_RELOAD;
stm32f7_i2c_clr_bits(base + STM32F7_I2C_CR2, mask);
mask = STM32F7_I2C_CR1_SBC | STM32F7_I2C_CR1_RXIE |
STM32F7_I2C_CR1_TCIE;
stm32f7_i2c_clr_bits(base + STM32F7_I2C_CR1, mask);
/* Enable TX empty, STOP, NACK interrupts */
mask = STM32F7_I2C_CR1_STOPIE | STM32F7_I2C_CR1_NACKIE |
STM32F7_I2C_CR1_TXIE;
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR1, mask);
/* Write 1st data byte */
writel_relaxed(value, base + STM32F7_I2C_TXDR);
} else {
/* Notify i2c slave that new write transfer is starting */
i2c_slave_event(slave, I2C_SLAVE_WRITE_REQUESTED, &value);
/* Set reload mode to be able to ACK/NACK each received byte */
mask = STM32F7_I2C_CR2_RELOAD;
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR2, mask);
/*
* Set STOP, NACK, RX empty and transfer complete interrupts.*
* Set Slave Byte Control to be able to ACK/NACK each data
* byte received
*/
mask = STM32F7_I2C_CR1_STOPIE | STM32F7_I2C_CR1_NACKIE |
STM32F7_I2C_CR1_SBC | STM32F7_I2C_CR1_RXIE |
STM32F7_I2C_CR1_TCIE;
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR1, mask);
}
}
static void stm32f7_i2c_slave_addr(struct stm32f7_i2c_dev *i2c_dev)
{
void __iomem *base = i2c_dev->base;
u32 isr, addcode, dir, mask;
int i;
isr = readl_relaxed(i2c_dev->base + STM32F7_I2C_ISR);
addcode = STM32F7_I2C_ISR_ADDCODE_GET(isr);
dir = isr & STM32F7_I2C_ISR_DIR;
for (i = 0; i < STM32F7_I2C_MAX_SLAVE; i++) {
if (stm32f7_i2c_is_addr_match(i2c_dev->slave[i], addcode)) {
i2c_dev->slave_running = i2c_dev->slave[i];
i2c_dev->slave_dir = dir;
/* Start I2C slave processing */
stm32f7_i2c_slave_start(i2c_dev);
/* Clear ADDR flag */
mask = STM32F7_I2C_ICR_ADDRCF;
writel_relaxed(mask, base + STM32F7_I2C_ICR);
break;
}
}
}
static int stm32f7_i2c_get_slave_id(struct stm32f7_i2c_dev *i2c_dev,
struct i2c_client *slave, int *id)
{
int i;
for (i = 0; i < STM32F7_I2C_MAX_SLAVE; i++) {
if (i2c_dev->slave[i] == slave) {
*id = i;
return 0;
}
}
dev_err(i2c_dev->dev, "Slave 0x%x not registered\n", slave->addr);
return -ENODEV;
}
static int stm32f7_i2c_get_free_slave_id(struct stm32f7_i2c_dev *i2c_dev,
struct i2c_client *slave, int *id)
{
struct device *dev = i2c_dev->dev;
int i;
/*
* slave[STM32F7_SLAVE_HOSTNOTIFY] support only SMBus Host address (0x8)
* slave[STM32F7_SLAVE_7_10_BITS_ADDR] supports 7-bit and 10-bit slave address
* slave[STM32F7_SLAVE_7_BITS_ADDR] supports 7-bit slave address only
*/
if (i2c_dev->smbus_mode && (slave->addr == 0x08)) {
if (i2c_dev->slave[STM32F7_SLAVE_HOSTNOTIFY])
goto fail;
*id = STM32F7_SLAVE_HOSTNOTIFY;
return 0;
}
for (i = STM32F7_I2C_MAX_SLAVE - 1; i > STM32F7_SLAVE_HOSTNOTIFY; i--) {
if ((i == STM32F7_SLAVE_7_BITS_ADDR) &&
(slave->flags & I2C_CLIENT_TEN))
continue;
if (!i2c_dev->slave[i]) {
*id = i;
return 0;
}
}
fail:
dev_err(dev, "Slave 0x%x could not be registered\n", slave->addr);
return -EINVAL;
}
static bool stm32f7_i2c_is_slave_registered(struct stm32f7_i2c_dev *i2c_dev)
{
int i;
for (i = 0; i < STM32F7_I2C_MAX_SLAVE; i++) {
if (i2c_dev->slave[i])
return true;
}
return false;
}
static bool stm32f7_i2c_is_slave_busy(struct stm32f7_i2c_dev *i2c_dev)
{
int i, busy;
busy = 0;
for (i = 0; i < STM32F7_I2C_MAX_SLAVE; i++) {
if (i2c_dev->slave[i])
busy++;
}
return i == busy;
}
static irqreturn_t stm32f7_i2c_slave_isr_event(struct stm32f7_i2c_dev *i2c_dev)
{
void __iomem *base = i2c_dev->base;
u32 cr2, status, mask;
u8 val;
int ret;
status = readl_relaxed(i2c_dev->base + STM32F7_I2C_ISR);
/* Slave transmitter mode */
if (status & STM32F7_I2C_ISR_TXIS) {
i2c_slave_event(i2c_dev->slave_running,
I2C_SLAVE_READ_PROCESSED,
&val);
/* Write data byte */
writel_relaxed(val, base + STM32F7_I2C_TXDR);
}
/* Transfer Complete Reload for Slave receiver mode */
if (status & STM32F7_I2C_ISR_TCR || status & STM32F7_I2C_ISR_RXNE) {
/*
* Read data byte then set NBYTES to receive next byte or NACK
* the current received byte
*/
val = readb_relaxed(i2c_dev->base + STM32F7_I2C_RXDR);
ret = i2c_slave_event(i2c_dev->slave_running,
I2C_SLAVE_WRITE_RECEIVED,
&val);
if (!ret) {
cr2 = readl_relaxed(i2c_dev->base + STM32F7_I2C_CR2);
cr2 |= STM32F7_I2C_CR2_NBYTES(1);
writel_relaxed(cr2, i2c_dev->base + STM32F7_I2C_CR2);
} else {
mask = STM32F7_I2C_CR2_NACK;
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR2, mask);
}
}
/* NACK received */
if (status & STM32F7_I2C_ISR_NACKF) {
dev_dbg(i2c_dev->dev, "<%s>: Receive NACK\n", __func__);
writel_relaxed(STM32F7_I2C_ICR_NACKCF, base + STM32F7_I2C_ICR);
}
/* STOP received */
if (status & STM32F7_I2C_ISR_STOPF) {
/* Disable interrupts */
stm32f7_i2c_disable_irq(i2c_dev, STM32F7_I2C_XFER_IRQ_MASK);
if (i2c_dev->slave_dir) {
/*
* Flush TX buffer in order to not used the byte in
* TXDR for the next transfer
*/
mask = STM32F7_I2C_ISR_TXE;
stm32f7_i2c_set_bits(base + STM32F7_I2C_ISR, mask);
}
/* Clear STOP flag */
writel_relaxed(STM32F7_I2C_ICR_STOPCF, base + STM32F7_I2C_ICR);
/* Notify i2c slave that a STOP flag has been detected */
i2c_slave_event(i2c_dev->slave_running, I2C_SLAVE_STOP, &val);
i2c_dev->slave_running = NULL;
}
/* Address match received */
if (status & STM32F7_I2C_ISR_ADDR)
stm32f7_i2c_slave_addr(i2c_dev);
return IRQ_HANDLED;
}
static irqreturn_t stm32f7_i2c_isr_event(int irq, void *data)
{
struct stm32f7_i2c_dev *i2c_dev = data;
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
struct stm32_i2c_dma *dma = i2c_dev->dma;
void __iomem *base = i2c_dev->base;
u32 status, mask;
int ret = IRQ_HANDLED;
/* Check if the interrupt if for a slave device */
if (!i2c_dev->master_mode) {
ret = stm32f7_i2c_slave_isr_event(i2c_dev);
return ret;
}
status = readl_relaxed(i2c_dev->base + STM32F7_I2C_ISR);
/* Tx empty */
if (status & STM32F7_I2C_ISR_TXIS)
stm32f7_i2c_write_tx_data(i2c_dev);
/* RX not empty */
if (status & STM32F7_I2C_ISR_RXNE)
stm32f7_i2c_read_rx_data(i2c_dev);
/* NACK received */
if (status & STM32F7_I2C_ISR_NACKF) {
dev_dbg(i2c_dev->dev, "<%s>: Receive NACK (addr %x)\n",
__func__, f7_msg->addr);
writel_relaxed(STM32F7_I2C_ICR_NACKCF, base + STM32F7_I2C_ICR);
if (i2c_dev->use_dma) {
stm32f7_i2c_disable_dma_req(i2c_dev);
dmaengine_terminate_async(dma->chan_using);
}
f7_msg->result = -ENXIO;
}
/* STOP detection flag */
if (status & STM32F7_I2C_ISR_STOPF) {
/* Disable interrupts */
if (stm32f7_i2c_is_slave_registered(i2c_dev))
mask = STM32F7_I2C_XFER_IRQ_MASK;
else
mask = STM32F7_I2C_ALL_IRQ_MASK;
stm32f7_i2c_disable_irq(i2c_dev, mask);
/* Clear STOP flag */
writel_relaxed(STM32F7_I2C_ICR_STOPCF, base + STM32F7_I2C_ICR);
if (i2c_dev->use_dma && !f7_msg->result) {
ret = IRQ_WAKE_THREAD;
} else {
i2c_dev->master_mode = false;
complete(&i2c_dev->complete);
}
}
/* Transfer complete */
if (status & STM32F7_I2C_ISR_TC) {
if (f7_msg->stop) {
mask = STM32F7_I2C_CR2_STOP;
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR2, mask);
} else if (i2c_dev->use_dma && !f7_msg->result) {
ret = IRQ_WAKE_THREAD;
} else if (f7_msg->smbus) {
stm32f7_i2c_smbus_rep_start(i2c_dev);
} else {
i2c_dev->msg_id++;
i2c_dev->msg++;
stm32f7_i2c_xfer_msg(i2c_dev, i2c_dev->msg);
}
}
if (status & STM32F7_I2C_ISR_TCR) {
if (f7_msg->smbus)
stm32f7_i2c_smbus_reload(i2c_dev);
else
stm32f7_i2c_reload(i2c_dev);
}
return ret;
}
static irqreturn_t stm32f7_i2c_isr_event_thread(int irq, void *data)
{
struct stm32f7_i2c_dev *i2c_dev = data;
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
struct stm32_i2c_dma *dma = i2c_dev->dma;
u32 status;
int ret;
/*
* Wait for dma transfer completion before sending next message or
* notity the end of xfer to the client
*/
ret = wait_for_completion_timeout(&i2c_dev->dma->dma_complete, HZ);
if (!ret) {
dev_dbg(i2c_dev->dev, "<%s>: Timed out\n", __func__);
stm32f7_i2c_disable_dma_req(i2c_dev);
dmaengine_terminate_async(dma->chan_using);
f7_msg->result = -ETIMEDOUT;
}
status = readl_relaxed(i2c_dev->base + STM32F7_I2C_ISR);
if (status & STM32F7_I2C_ISR_TC) {
if (f7_msg->smbus) {
stm32f7_i2c_smbus_rep_start(i2c_dev);
} else {
i2c_dev->msg_id++;
i2c_dev->msg++;
stm32f7_i2c_xfer_msg(i2c_dev, i2c_dev->msg);
}
} else {
i2c_dev->master_mode = false;
complete(&i2c_dev->complete);
}
return IRQ_HANDLED;
}
static irqreturn_t stm32f7_i2c_isr_error(int irq, void *data)
{
struct stm32f7_i2c_dev *i2c_dev = data;
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
void __iomem *base = i2c_dev->base;
struct device *dev = i2c_dev->dev;
struct stm32_i2c_dma *dma = i2c_dev->dma;
u32 status;
status = readl_relaxed(i2c_dev->base + STM32F7_I2C_ISR);
/* Bus error */
if (status & STM32F7_I2C_ISR_BERR) {
dev_err(dev, "<%s>: Bus error accessing addr 0x%x\n",
__func__, f7_msg->addr);
writel_relaxed(STM32F7_I2C_ICR_BERRCF, base + STM32F7_I2C_ICR);
stm32f7_i2c_release_bus(&i2c_dev->adap);
f7_msg->result = -EIO;
}
/* Arbitration loss */
if (status & STM32F7_I2C_ISR_ARLO) {
dev_dbg(dev, "<%s>: Arbitration loss accessing addr 0x%x\n",
__func__, f7_msg->addr);
writel_relaxed(STM32F7_I2C_ICR_ARLOCF, base + STM32F7_I2C_ICR);
f7_msg->result = -EAGAIN;
}
if (status & STM32F7_I2C_ISR_PECERR) {
dev_err(dev, "<%s>: PEC error in reception accessing addr 0x%x\n",
__func__, f7_msg->addr);
writel_relaxed(STM32F7_I2C_ICR_PECCF, base + STM32F7_I2C_ICR);
f7_msg->result = -EINVAL;
}
if (status & STM32F7_I2C_ISR_ALERT) {
dev_dbg(dev, "<%s>: SMBus alert received\n", __func__);
writel_relaxed(STM32F7_I2C_ICR_ALERTCF, base + STM32F7_I2C_ICR);
i2c_handle_smbus_alert(i2c_dev->alert->ara);
return IRQ_HANDLED;
}
if (!i2c_dev->slave_running) {
u32 mask;
/* Disable interrupts */
if (stm32f7_i2c_is_slave_registered(i2c_dev))
mask = STM32F7_I2C_XFER_IRQ_MASK;
else
mask = STM32F7_I2C_ALL_IRQ_MASK;
stm32f7_i2c_disable_irq(i2c_dev, mask);
}
/* Disable dma */
if (i2c_dev->use_dma) {
stm32f7_i2c_disable_dma_req(i2c_dev);
dmaengine_terminate_async(dma->chan_using);
}
i2c_dev->master_mode = false;
complete(&i2c_dev->complete);
return IRQ_HANDLED;
}
static int stm32f7_i2c_xfer(struct i2c_adapter *i2c_adap,
struct i2c_msg msgs[], int num)
{
struct stm32f7_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
struct stm32_i2c_dma *dma = i2c_dev->dma;
unsigned long time_left;
int ret;
i2c_dev->msg = msgs;
i2c_dev->msg_num = num;
i2c_dev->msg_id = 0;
f7_msg->smbus = false;
ret = pm_runtime_resume_and_get(i2c_dev->dev);
if (ret < 0)
return ret;
ret = stm32f7_i2c_wait_free_bus(i2c_dev);
if (ret)
goto pm_free;
stm32f7_i2c_xfer_msg(i2c_dev, msgs);
time_left = wait_for_completion_timeout(&i2c_dev->complete,
i2c_dev->adap.timeout);
ret = f7_msg->result;
if (ret) {
if (i2c_dev->use_dma)
dmaengine_synchronize(dma->chan_using);
/*
* It is possible that some unsent data have already been
* written into TXDR. To avoid sending old data in a
* further transfer, flush TXDR in case of any error
*/
writel_relaxed(STM32F7_I2C_ISR_TXE,
i2c_dev->base + STM32F7_I2C_ISR);
goto pm_free;
}
if (!time_left) {
dev_dbg(i2c_dev->dev, "Access to slave 0x%x timed out\n",
i2c_dev->msg->addr);
if (i2c_dev->use_dma)
dmaengine_terminate_sync(dma->chan_using);
stm32f7_i2c_wait_free_bus(i2c_dev);
ret = -ETIMEDOUT;
}
pm_free:
pm_runtime_mark_last_busy(i2c_dev->dev);
pm_runtime_put_autosuspend(i2c_dev->dev);
return (ret < 0) ? ret : num;
}
static int stm32f7_i2c_smbus_xfer(struct i2c_adapter *adapter, u16 addr,
unsigned short flags, char read_write,
u8 command, int size,
union i2c_smbus_data *data)
{
struct stm32f7_i2c_dev *i2c_dev = i2c_get_adapdata(adapter);
struct stm32f7_i2c_msg *f7_msg = &i2c_dev->f7_msg;
struct stm32_i2c_dma *dma = i2c_dev->dma;
struct device *dev = i2c_dev->dev;
unsigned long timeout;
int i, ret;
f7_msg->addr = addr;
f7_msg->size = size;
f7_msg->read_write = read_write;
f7_msg->smbus = true;
ret = pm_runtime_resume_and_get(dev);
if (ret < 0)
return ret;
ret = stm32f7_i2c_wait_free_bus(i2c_dev);
if (ret)
goto pm_free;
ret = stm32f7_i2c_smbus_xfer_msg(i2c_dev, flags, command, data);
if (ret)
goto pm_free;
timeout = wait_for_completion_timeout(&i2c_dev->complete,
i2c_dev->adap.timeout);
ret = f7_msg->result;
if (ret) {
if (i2c_dev->use_dma)
dmaengine_synchronize(dma->chan_using);
/*
* It is possible that some unsent data have already been
* written into TXDR. To avoid sending old data in a
* further transfer, flush TXDR in case of any error
*/
writel_relaxed(STM32F7_I2C_ISR_TXE,
i2c_dev->base + STM32F7_I2C_ISR);
goto pm_free;
}
if (!timeout) {
dev_dbg(dev, "Access to slave 0x%x timed out\n", f7_msg->addr);
if (i2c_dev->use_dma)
dmaengine_terminate_sync(dma->chan_using);
stm32f7_i2c_wait_free_bus(i2c_dev);
ret = -ETIMEDOUT;
goto pm_free;
}
/* Check PEC */
if ((flags & I2C_CLIENT_PEC) && size != I2C_SMBUS_QUICK && read_write) {
ret = stm32f7_i2c_smbus_check_pec(i2c_dev);
if (ret)
goto pm_free;
}
if (read_write && size != I2C_SMBUS_QUICK) {
switch (size) {
case I2C_SMBUS_BYTE:
case I2C_SMBUS_BYTE_DATA:
data->byte = f7_msg->smbus_buf[0];
break;
case I2C_SMBUS_WORD_DATA:
case I2C_SMBUS_PROC_CALL:
data->word = f7_msg->smbus_buf[0] |
(f7_msg->smbus_buf[1] << 8);
break;
case I2C_SMBUS_BLOCK_DATA:
case I2C_SMBUS_BLOCK_PROC_CALL:
for (i = 0; i <= f7_msg->smbus_buf[0]; i++)
data->block[i] = f7_msg->smbus_buf[i];
break;
default:
dev_err(dev, "Unsupported smbus transaction\n");
ret = -EINVAL;
}
}
pm_free:
pm_runtime_mark_last_busy(dev);
pm_runtime_put_autosuspend(dev);
return ret;
}
static void stm32f7_i2c_enable_wakeup(struct stm32f7_i2c_dev *i2c_dev,
bool enable)
{
void __iomem *base = i2c_dev->base;
u32 mask = STM32F7_I2C_CR1_WUPEN;
if (!i2c_dev->wakeup_src)
return;
if (enable) {
device_set_wakeup_enable(i2c_dev->dev, true);
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR1, mask);
} else {
device_set_wakeup_enable(i2c_dev->dev, false);
stm32f7_i2c_clr_bits(base + STM32F7_I2C_CR1, mask);
}
}
static int stm32f7_i2c_reg_slave(struct i2c_client *slave)
{
struct stm32f7_i2c_dev *i2c_dev = i2c_get_adapdata(slave->adapter);
void __iomem *base = i2c_dev->base;
struct device *dev = i2c_dev->dev;
u32 oar1, oar2, mask;
int id, ret;
if (slave->flags & I2C_CLIENT_PEC) {
dev_err(dev, "SMBus PEC not supported in slave mode\n");
return -EINVAL;
}
if (stm32f7_i2c_is_slave_busy(i2c_dev)) {
dev_err(dev, "Too much slave registered\n");
return -EBUSY;
}
ret = stm32f7_i2c_get_free_slave_id(i2c_dev, slave, &id);
if (ret)
return ret;
ret = pm_runtime_resume_and_get(dev);
if (ret < 0)
return ret;
if (!stm32f7_i2c_is_slave_registered(i2c_dev))
stm32f7_i2c_enable_wakeup(i2c_dev, true);
switch (id) {
case 0:
/* Slave SMBus Host */
i2c_dev->slave[id] = slave;
break;
case 1:
/* Configure Own Address 1 */
oar1 = readl_relaxed(i2c_dev->base + STM32F7_I2C_OAR1);
oar1 &= ~STM32F7_I2C_OAR1_MASK;
if (slave->flags & I2C_CLIENT_TEN) {
oar1 |= STM32F7_I2C_OAR1_OA1_10(slave->addr);
oar1 |= STM32F7_I2C_OAR1_OA1MODE;
} else {
oar1 |= STM32F7_I2C_OAR1_OA1_7(slave->addr);
}
oar1 |= STM32F7_I2C_OAR1_OA1EN;
i2c_dev->slave[id] = slave;
writel_relaxed(oar1, i2c_dev->base + STM32F7_I2C_OAR1);
break;
case 2:
/* Configure Own Address 2 */
oar2 = readl_relaxed(i2c_dev->base + STM32F7_I2C_OAR2);
oar2 &= ~STM32F7_I2C_OAR2_MASK;
if (slave->flags & I2C_CLIENT_TEN) {
ret = -EOPNOTSUPP;
goto pm_free;
}
oar2 |= STM32F7_I2C_OAR2_OA2_7(slave->addr);
oar2 |= STM32F7_I2C_OAR2_OA2EN;
i2c_dev->slave[id] = slave;
writel_relaxed(oar2, i2c_dev->base + STM32F7_I2C_OAR2);
break;
default:
dev_err(dev, "I2C slave id not supported\n");
ret = -ENODEV;
goto pm_free;
}
/* Enable ACK */
stm32f7_i2c_clr_bits(base + STM32F7_I2C_CR2, STM32F7_I2C_CR2_NACK);
/* Enable Address match interrupt, error interrupt and enable I2C */
mask = STM32F7_I2C_CR1_ADDRIE | STM32F7_I2C_CR1_ERRIE |
STM32F7_I2C_CR1_PE;
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR1, mask);
ret = 0;
pm_free:
if (!stm32f7_i2c_is_slave_registered(i2c_dev))
stm32f7_i2c_enable_wakeup(i2c_dev, false);
pm_runtime_mark_last_busy(dev);
pm_runtime_put_autosuspend(dev);
return ret;
}
static int stm32f7_i2c_unreg_slave(struct i2c_client *slave)
{
struct stm32f7_i2c_dev *i2c_dev = i2c_get_adapdata(slave->adapter);
void __iomem *base = i2c_dev->base;
u32 mask;
int id, ret;
ret = stm32f7_i2c_get_slave_id(i2c_dev, slave, &id);
if (ret)
return ret;
WARN_ON(!i2c_dev->slave[id]);
ret = pm_runtime_resume_and_get(i2c_dev->dev);
if (ret < 0)
return ret;
if (id == 1) {
mask = STM32F7_I2C_OAR1_OA1EN;
stm32f7_i2c_clr_bits(base + STM32F7_I2C_OAR1, mask);
} else if (id == 2) {
mask = STM32F7_I2C_OAR2_OA2EN;
stm32f7_i2c_clr_bits(base + STM32F7_I2C_OAR2, mask);
}
i2c_dev->slave[id] = NULL;
if (!stm32f7_i2c_is_slave_registered(i2c_dev)) {
stm32f7_i2c_disable_irq(i2c_dev, STM32F7_I2C_ALL_IRQ_MASK);
stm32f7_i2c_enable_wakeup(i2c_dev, false);
}
pm_runtime_mark_last_busy(i2c_dev->dev);
pm_runtime_put_autosuspend(i2c_dev->dev);
return 0;
}
static int stm32f7_i2c_write_fm_plus_bits(struct stm32f7_i2c_dev *i2c_dev,
bool enable)
{
int ret;
if (i2c_dev->bus_rate <= I2C_MAX_FAST_MODE_FREQ ||
IS_ERR_OR_NULL(i2c_dev->regmap))
/* Optional */
return 0;
if (i2c_dev->fmp_sreg == i2c_dev->fmp_creg)
ret = regmap_update_bits(i2c_dev->regmap,
i2c_dev->fmp_sreg,
i2c_dev->fmp_mask,
enable ? i2c_dev->fmp_mask : 0);
else
ret = regmap_write(i2c_dev->regmap,
enable ? i2c_dev->fmp_sreg :
i2c_dev->fmp_creg,
i2c_dev->fmp_mask);
return ret;
}
static int stm32f7_i2c_setup_fm_plus_bits(struct platform_device *pdev,
struct stm32f7_i2c_dev *i2c_dev)
{
struct device_node *np = pdev->dev.of_node;
int ret;
i2c_dev->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg-fmp");
if (IS_ERR(i2c_dev->regmap))
/* Optional */
return 0;
ret = of_property_read_u32_index(np, "st,syscfg-fmp", 1,
&i2c_dev->fmp_sreg);
if (ret)
return ret;
i2c_dev->fmp_creg = i2c_dev->fmp_sreg +
i2c_dev->setup.fmp_clr_offset;
return of_property_read_u32_index(np, "st,syscfg-fmp", 2,
&i2c_dev->fmp_mask);
}
static int stm32f7_i2c_enable_smbus_host(struct stm32f7_i2c_dev *i2c_dev)
{
struct i2c_adapter *adap = &i2c_dev->adap;
void __iomem *base = i2c_dev->base;
struct i2c_client *client;
client = i2c_new_slave_host_notify_device(adap);
if (IS_ERR(client))
return PTR_ERR(client);
i2c_dev->host_notify_client = client;
/* Enable SMBus Host address */
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR1, STM32F7_I2C_CR1_SMBHEN);
return 0;
}
static void stm32f7_i2c_disable_smbus_host(struct stm32f7_i2c_dev *i2c_dev)
{
void __iomem *base = i2c_dev->base;
if (i2c_dev->host_notify_client) {
/* Disable SMBus Host address */
stm32f7_i2c_clr_bits(base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_SMBHEN);
i2c_free_slave_host_notify_device(i2c_dev->host_notify_client);
}
}
static int stm32f7_i2c_enable_smbus_alert(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_alert *alert;
struct i2c_adapter *adap = &i2c_dev->adap;
struct device *dev = i2c_dev->dev;
void __iomem *base = i2c_dev->base;
alert = devm_kzalloc(dev, sizeof(*alert), GFP_KERNEL);
if (!alert)
return -ENOMEM;
alert->ara = i2c_new_smbus_alert_device(adap, &alert->setup);
if (IS_ERR(alert->ara))
return PTR_ERR(alert->ara);
i2c_dev->alert = alert;
/* Enable SMBus Alert */
stm32f7_i2c_set_bits(base + STM32F7_I2C_CR1, STM32F7_I2C_CR1_ALERTEN);
return 0;
}
static void stm32f7_i2c_disable_smbus_alert(struct stm32f7_i2c_dev *i2c_dev)
{
struct stm32f7_i2c_alert *alert = i2c_dev->alert;
void __iomem *base = i2c_dev->base;
if (alert) {
/* Disable SMBus Alert */
stm32f7_i2c_clr_bits(base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_ALERTEN);
i2c_unregister_device(alert->ara);
}
}
static u32 stm32f7_i2c_func(struct i2c_adapter *adap)
{
struct stm32f7_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
u32 func = I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR | I2C_FUNC_SLAVE |
I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE |
I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA |
I2C_FUNC_SMBUS_BLOCK_DATA | I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
I2C_FUNC_SMBUS_PROC_CALL | I2C_FUNC_SMBUS_PEC |
I2C_FUNC_SMBUS_I2C_BLOCK;
if (i2c_dev->smbus_mode)
func |= I2C_FUNC_SMBUS_HOST_NOTIFY;
return func;
}
static const struct i2c_algorithm stm32f7_i2c_algo = {
.master_xfer = stm32f7_i2c_xfer,
.smbus_xfer = stm32f7_i2c_smbus_xfer,
.functionality = stm32f7_i2c_func,
.reg_slave = stm32f7_i2c_reg_slave,
.unreg_slave = stm32f7_i2c_unreg_slave,
};
static int stm32f7_i2c_probe(struct platform_device *pdev)
{
struct stm32f7_i2c_dev *i2c_dev;
const struct stm32f7_i2c_setup *setup;
struct resource *res;
struct i2c_adapter *adap;
struct reset_control *rst;
dma_addr_t phy_addr;
int irq_error, irq_event, ret;
i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
if (!i2c_dev)
return -ENOMEM;
i2c_dev->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
if (IS_ERR(i2c_dev->base))
return PTR_ERR(i2c_dev->base);
phy_addr = (dma_addr_t)res->start;
irq_event = platform_get_irq(pdev, 0);
if (irq_event < 0)
return irq_event;
irq_error = platform_get_irq(pdev, 1);
if (irq_error < 0)
return irq_error;
i2c_dev->wakeup_src = of_property_read_bool(pdev->dev.of_node,
"wakeup-source");
i2c_dev->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(i2c_dev->clk))
return dev_err_probe(&pdev->dev, PTR_ERR(i2c_dev->clk),
"Failed to get controller clock\n");
ret = clk_prepare_enable(i2c_dev->clk);
if (ret) {
dev_err(&pdev->dev, "Failed to prepare_enable clock\n");
return ret;
}
rst = devm_reset_control_get(&pdev->dev, NULL);
if (IS_ERR(rst)) {
ret = dev_err_probe(&pdev->dev, PTR_ERR(rst),
"Error: Missing reset ctrl\n");
goto clk_free;
}
reset_control_assert(rst);
udelay(2);
reset_control_deassert(rst);
i2c_dev->dev = &pdev->dev;
ret = devm_request_threaded_irq(&pdev->dev, irq_event,
stm32f7_i2c_isr_event,
stm32f7_i2c_isr_event_thread,
IRQF_ONESHOT,
pdev->name, i2c_dev);
if (ret) {
dev_err(&pdev->dev, "Failed to request irq event %i\n",
irq_event);
goto clk_free;
}
ret = devm_request_irq(&pdev->dev, irq_error, stm32f7_i2c_isr_error, 0,
pdev->name, i2c_dev);
if (ret) {
dev_err(&pdev->dev, "Failed to request irq error %i\n",
irq_error);
goto clk_free;
}
setup = of_device_get_match_data(&pdev->dev);
if (!setup) {
dev_err(&pdev->dev, "Can't get device data\n");
ret = -ENODEV;
goto clk_free;
}
i2c_dev->setup = *setup;
ret = stm32f7_i2c_setup_timing(i2c_dev, &i2c_dev->setup);
if (ret)
goto clk_free;
/* Setup Fast mode plus if necessary */
if (i2c_dev->bus_rate > I2C_MAX_FAST_MODE_FREQ) {
ret = stm32f7_i2c_setup_fm_plus_bits(pdev, i2c_dev);
if (ret)
goto clk_free;
ret = stm32f7_i2c_write_fm_plus_bits(i2c_dev, true);
if (ret)
goto clk_free;
}
adap = &i2c_dev->adap;
i2c_set_adapdata(adap, i2c_dev);
snprintf(adap->name, sizeof(adap->name), "STM32F7 I2C(%pa)",
&res->start);
adap->owner = THIS_MODULE;
adap->timeout = 2 * HZ;
adap->retries = 3;
adap->algo = &stm32f7_i2c_algo;
adap->dev.parent = &pdev->dev;
adap->dev.of_node = pdev->dev.of_node;
init_completion(&i2c_dev->complete);
/* Init DMA config if supported */
i2c_dev->dma = stm32_i2c_dma_request(i2c_dev->dev, phy_addr,
STM32F7_I2C_TXDR,
STM32F7_I2C_RXDR);
if (IS_ERR(i2c_dev->dma)) {
ret = PTR_ERR(i2c_dev->dma);
/* DMA support is optional, only report other errors */
if (ret != -ENODEV)
goto fmp_clear;
dev_dbg(i2c_dev->dev, "No DMA option: fallback using interrupts\n");
i2c_dev->dma = NULL;
}
if (i2c_dev->wakeup_src) {
device_set_wakeup_capable(i2c_dev->dev, true);
ret = dev_pm_set_wake_irq(i2c_dev->dev, irq_event);
if (ret) {
dev_err(i2c_dev->dev, "Failed to set wake up irq\n");
goto clr_wakeup_capable;
}
}
platform_set_drvdata(pdev, i2c_dev);
pm_runtime_set_autosuspend_delay(i2c_dev->dev,
STM32F7_AUTOSUSPEND_DELAY);
pm_runtime_use_autosuspend(i2c_dev->dev);
pm_runtime_set_active(i2c_dev->dev);
pm_runtime_enable(i2c_dev->dev);
pm_runtime_get_noresume(&pdev->dev);
stm32f7_i2c_hw_config(i2c_dev);
i2c_dev->smbus_mode = of_property_read_bool(pdev->dev.of_node, "smbus");
ret = i2c_add_adapter(adap);
if (ret)
goto pm_disable;
if (i2c_dev->smbus_mode) {
ret = stm32f7_i2c_enable_smbus_host(i2c_dev);
if (ret) {
dev_err(i2c_dev->dev,
"failed to enable SMBus Host-Notify protocol (%d)\n",
ret);
goto i2c_adapter_remove;
}
}
if (of_property_read_bool(pdev->dev.of_node, "smbus-alert")) {
ret = stm32f7_i2c_enable_smbus_alert(i2c_dev);
if (ret) {
dev_err(i2c_dev->dev,
"failed to enable SMBus alert protocol (%d)\n",
ret);
goto i2c_disable_smbus_host;
}
}
dev_info(i2c_dev->dev, "STM32F7 I2C-%d bus adapter\n", adap->nr);
pm_runtime_mark_last_busy(i2c_dev->dev);
pm_runtime_put_autosuspend(i2c_dev->dev);
return 0;
i2c_disable_smbus_host:
stm32f7_i2c_disable_smbus_host(i2c_dev);
i2c_adapter_remove:
i2c_del_adapter(adap);
pm_disable:
pm_runtime_put_noidle(i2c_dev->dev);
pm_runtime_disable(i2c_dev->dev);
pm_runtime_set_suspended(i2c_dev->dev);
pm_runtime_dont_use_autosuspend(i2c_dev->dev);
if (i2c_dev->wakeup_src)
dev_pm_clear_wake_irq(i2c_dev->dev);
clr_wakeup_capable:
if (i2c_dev->wakeup_src)
device_set_wakeup_capable(i2c_dev->dev, false);
if (i2c_dev->dma) {
stm32_i2c_dma_free(i2c_dev->dma);
i2c_dev->dma = NULL;
}
fmp_clear:
stm32f7_i2c_write_fm_plus_bits(i2c_dev, false);
clk_free:
clk_disable_unprepare(i2c_dev->clk);
return ret;
}
i2c: Convert to platform remove callback returning void The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is (mostly) ignored and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Alain Volmat <alain.volmat@foss.st.com> Acked-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Acked-by: Jochen Friedrich <jochen@scram.de> Acked-by: Peter Rosin <peda@axentia.se> Acked-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Asmaa Mnebhi <asnaa@nvidia.com> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Chris Pringle <chris.pringle@phabrix.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Tali Perry <tali.perry@nuvoton.com> Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-05-09 04:51:38 +08:00
static void stm32f7_i2c_remove(struct platform_device *pdev)
{
struct stm32f7_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
stm32f7_i2c_disable_smbus_alert(i2c_dev);
stm32f7_i2c_disable_smbus_host(i2c_dev);
i2c_del_adapter(&i2c_dev->adap);
pm_runtime_get_sync(i2c_dev->dev);
if (i2c_dev->wakeup_src) {
dev_pm_clear_wake_irq(i2c_dev->dev);
/*
* enforce that wakeup is disabled and that the device
* is marked as non wakeup capable
*/
device_init_wakeup(i2c_dev->dev, false);
}
pm_runtime_put_noidle(i2c_dev->dev);
pm_runtime_disable(i2c_dev->dev);
pm_runtime_set_suspended(i2c_dev->dev);
pm_runtime_dont_use_autosuspend(i2c_dev->dev);
if (i2c_dev->dma) {
stm32_i2c_dma_free(i2c_dev->dma);
i2c_dev->dma = NULL;
}
stm32f7_i2c_write_fm_plus_bits(i2c_dev, false);
clk_disable_unprepare(i2c_dev->clk);
}
static int __maybe_unused stm32f7_i2c_runtime_suspend(struct device *dev)
{
struct stm32f7_i2c_dev *i2c_dev = dev_get_drvdata(dev);
if (!stm32f7_i2c_is_slave_registered(i2c_dev))
clk_disable_unprepare(i2c_dev->clk);
return 0;
}
static int __maybe_unused stm32f7_i2c_runtime_resume(struct device *dev)
{
struct stm32f7_i2c_dev *i2c_dev = dev_get_drvdata(dev);
int ret;
if (!stm32f7_i2c_is_slave_registered(i2c_dev)) {
ret = clk_prepare_enable(i2c_dev->clk);
if (ret) {
dev_err(dev, "failed to prepare_enable clock\n");
return ret;
}
}
return 0;
}
static int __maybe_unused stm32f7_i2c_regs_backup(struct stm32f7_i2c_dev *i2c_dev)
{
int ret;
struct stm32f7_i2c_regs *backup_regs = &i2c_dev->backup_regs;
ret = pm_runtime_resume_and_get(i2c_dev->dev);
if (ret < 0)
return ret;
backup_regs->cr1 = readl_relaxed(i2c_dev->base + STM32F7_I2C_CR1);
backup_regs->cr2 = readl_relaxed(i2c_dev->base + STM32F7_I2C_CR2);
backup_regs->oar1 = readl_relaxed(i2c_dev->base + STM32F7_I2C_OAR1);
backup_regs->oar2 = readl_relaxed(i2c_dev->base + STM32F7_I2C_OAR2);
backup_regs->tmgr = readl_relaxed(i2c_dev->base + STM32F7_I2C_TIMINGR);
stm32f7_i2c_write_fm_plus_bits(i2c_dev, false);
pm_runtime_put_sync(i2c_dev->dev);
return ret;
}
static int __maybe_unused stm32f7_i2c_regs_restore(struct stm32f7_i2c_dev *i2c_dev)
{
u32 cr1;
int ret;
struct stm32f7_i2c_regs *backup_regs = &i2c_dev->backup_regs;
ret = pm_runtime_resume_and_get(i2c_dev->dev);
if (ret < 0)
return ret;
cr1 = readl_relaxed(i2c_dev->base + STM32F7_I2C_CR1);
if (cr1 & STM32F7_I2C_CR1_PE)
stm32f7_i2c_clr_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_PE);
writel_relaxed(backup_regs->tmgr, i2c_dev->base + STM32F7_I2C_TIMINGR);
writel_relaxed(backup_regs->cr1 & ~STM32F7_I2C_CR1_PE,
i2c_dev->base + STM32F7_I2C_CR1);
if (backup_regs->cr1 & STM32F7_I2C_CR1_PE)
stm32f7_i2c_set_bits(i2c_dev->base + STM32F7_I2C_CR1,
STM32F7_I2C_CR1_PE);
writel_relaxed(backup_regs->cr2, i2c_dev->base + STM32F7_I2C_CR2);
writel_relaxed(backup_regs->oar1, i2c_dev->base + STM32F7_I2C_OAR1);
writel_relaxed(backup_regs->oar2, i2c_dev->base + STM32F7_I2C_OAR2);
stm32f7_i2c_write_fm_plus_bits(i2c_dev, true);
pm_runtime_put_sync(i2c_dev->dev);
return ret;
}
static int __maybe_unused stm32f7_i2c_suspend(struct device *dev)
{
struct stm32f7_i2c_dev *i2c_dev = dev_get_drvdata(dev);
int ret;
i2c_mark_adapter_suspended(&i2c_dev->adap);
if (!device_may_wakeup(dev) && !device_wakeup_path(dev)) {
ret = stm32f7_i2c_regs_backup(i2c_dev);
if (ret < 0) {
i2c_mark_adapter_resumed(&i2c_dev->adap);
return ret;
}
pinctrl_pm_select_sleep_state(dev);
pm_runtime_force_suspend(dev);
}
return 0;
}
static int __maybe_unused stm32f7_i2c_resume(struct device *dev)
{
struct stm32f7_i2c_dev *i2c_dev = dev_get_drvdata(dev);
int ret;
if (!device_may_wakeup(dev) && !device_wakeup_path(dev)) {
ret = pm_runtime_force_resume(dev);
if (ret < 0)
return ret;
pinctrl_pm_select_default_state(dev);
ret = stm32f7_i2c_regs_restore(i2c_dev);
if (ret < 0)
return ret;
}
i2c_mark_adapter_resumed(&i2c_dev->adap);
return 0;
}
static const struct dev_pm_ops stm32f7_i2c_pm_ops = {
SET_RUNTIME_PM_OPS(stm32f7_i2c_runtime_suspend,
stm32f7_i2c_runtime_resume, NULL)
SET_SYSTEM_SLEEP_PM_OPS(stm32f7_i2c_suspend, stm32f7_i2c_resume)
};
static const struct of_device_id stm32f7_i2c_match[] = {
{ .compatible = "st,stm32f7-i2c", .data = &stm32f7_setup},
{ .compatible = "st,stm32mp15-i2c", .data = &stm32mp15_setup},
{ .compatible = "st,stm32mp13-i2c", .data = &stm32mp13_setup},
{},
};
MODULE_DEVICE_TABLE(of, stm32f7_i2c_match);
static struct platform_driver stm32f7_i2c_driver = {
.driver = {
.name = "stm32f7-i2c",
.of_match_table = stm32f7_i2c_match,
.pm = &stm32f7_i2c_pm_ops,
},
.probe = stm32f7_i2c_probe,
i2c: Convert to platform remove callback returning void The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is (mostly) ignored and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Alain Volmat <alain.volmat@foss.st.com> Acked-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Acked-by: Jochen Friedrich <jochen@scram.de> Acked-by: Peter Rosin <peda@axentia.se> Acked-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Asmaa Mnebhi <asnaa@nvidia.com> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Chris Pringle <chris.pringle@phabrix.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Tali Perry <tali.perry@nuvoton.com> Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2023-05-09 04:51:38 +08:00
.remove_new = stm32f7_i2c_remove,
};
module_platform_driver(stm32f7_i2c_driver);
MODULE_AUTHOR("M'boumba Cedric Madianga <cedric.madianga@gmail.com>");
MODULE_DESCRIPTION("STMicroelectronics STM32F7 I2C driver");
MODULE_LICENSE("GPL v2");