OpenCloudOS-Kernel/drivers/soc/rockchip/Makefile

# SPDX-License-Identifier: GPL-2.0-only
#
# Rockchip Soc drivers
#
obj-$(CONFIG_ROCKCHIP_GRF) += grf.o
obj-$(CONFIG_ROCKCHIP_PM_DOMAINS) += pm_domains.o
treewide: Add SPDX license identifier - Makefile/Kconfig Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 2019-05-19 20:07:45 +08:00			`# SPDX-License-Identifier: GPL-2.0-only`
soc: rockchip: power-domain: Add power domain driver This driver is found on RK3288 SoCs. In order to meet high performance and low power requirements, a power management unit is designed or saving power when RK3288 in low power mode. The RK3288 PMU is dedicated for managing the power of the whole chip. PMU can work in the Low Power Mode by setting bit[0] of PMU_PWRMODE_CON register. After setting the register, PMU would enter the Low Power mode. In the low power mode, pmu will auto power on/off the specified power domain, send idle req to specified power domain, shut down/up pll and so on. All of above are configurable by setting corresponding registers. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> [replace dsb() with dsb(sy) for arm64 buildability; sy is the default, so no functional change; adapt to per-user clocks in genpd] Signed-off-by: Heiko Stuebner <heiko@sntech.de> 2015-09-08 14:18:22 +08:00			`#`
			`# Rockchip Soc drivers`
			`#`
soc: rockchip: add driver handling grf setup The General Register Files are an area of registers containing a lot of single-bit settings for numerous components as well full components like usbphy control. Therefore all used components are accessed via the syscon provided by the grf nodes or from the sub-devices created through the simple-mfd created from the grf node. Some settings are not used by anything but will need to be set up according to expectations on the kernel side. Best example is the force_jtag setting, which defaults to on and results in the soc switching the pin-outputs between jtag and sdmmc automatically depending on the card-detect status. This conflicts heavily with how the dw_mmc driver expects to do its work and also with the clock-controller, which has most likely deactivated the jtag clock due to it being unused. So far the handling of this setting was living in the mach-rockchip code for the arm32-based rk3288 but that of course doesn't work for arm64 socs and would also look ugly for further arm32 socs. Also always disabling this setting is quite specific to linux and its subsystems, other operating systems might prefer other settings, so that the bootloader cannot really set a sane default for all. So introduce a top-level driver for the grf that handles these settings that need to be a certain way but nobody cares about. Other needed settings might surface in the future and can then be added here, but only as a last option. Ideally general GRF settings should be handled in the driver needing them. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Douglas Anderson <dianders@chromium.org> 2016-11-17 07:03:03 +08:00			`obj-$(CONFIG_ROCKCHIP_GRF) += grf.o`
soc: rockchip: power-domain: Add power domain driver This driver is found on RK3288 SoCs. In order to meet high performance and low power requirements, a power management unit is designed or saving power when RK3288 in low power mode. The RK3288 PMU is dedicated for managing the power of the whole chip. PMU can work in the Low Power Mode by setting bit[0] of PMU_PWRMODE_CON register. After setting the register, PMU would enter the Low Power mode. In the low power mode, pmu will auto power on/off the specified power domain, send idle req to specified power domain, shut down/up pll and so on. All of above are configurable by setting corresponding registers. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> [replace dsb() with dsb(sy) for arm64 buildability; sy is the default, so no functional change; adapt to per-user clocks in genpd] Signed-off-by: Heiko Stuebner <heiko@sntech.de> 2015-09-08 14:18:22 +08:00			`obj-$(CONFIG_ROCKCHIP_PM_DOMAINS) += pm_domains.o`