OpenCloudOS-Kernel/drivers/iio/magnetometer/st_magn_buffer.c

91 lines
2.2 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* STMicroelectronics magnetometers driver
*
* Copyright 2012-2013 STMicroelectronics Inc.
*
* Denis Ciocca <denis.ciocca@st.com>
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/stat.h>
#include <linux/interrupt.h>
#include <linux/i2c.h>
#include <linux/delay.h>
#include <linux/iio/iio.h>
#include <linux/iio/buffer.h>
#include <linux/iio/trigger_consumer.h>
#include <linux/iio/triggered_buffer.h>
#include <linux/iio/common/st_sensors.h>
#include "st_magn.h"
int st_magn_trig_set_state(struct iio_trigger *trig, bool state)
{
struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
return st_sensors_set_dataready_irq(indio_dev, state);
}
static int st_magn_buffer_postenable(struct iio_dev *indio_dev)
{
int err;
struct st_sensor_data *mdata = iio_priv(indio_dev);
mdata->buffer_data = kmalloc(indio_dev->scan_bytes,
GFP_DMA | GFP_KERNEL);
if (mdata->buffer_data == NULL) {
err = -ENOMEM;
goto allocate_memory_error;
}
err = iio_triggered_buffer_postenable(indio_dev);
if (err < 0)
goto st_magn_buffer_postenable_error;
return st_sensors_set_enable(indio_dev, true);
st_magn_buffer_postenable_error:
kfree(mdata->buffer_data);
allocate_memory_error:
return err;
}
static int st_magn_buffer_predisable(struct iio_dev *indio_dev)
{
int err;
struct st_sensor_data *mdata = iio_priv(indio_dev);
err = st_sensors_set_enable(indio_dev, false);
if (err < 0)
goto st_magn_buffer_predisable_error;
err = iio_triggered_buffer_predisable(indio_dev);
st_magn_buffer_predisable_error:
kfree(mdata->buffer_data);
return err;
}
static const struct iio_buffer_setup_ops st_magn_buffer_setup_ops = {
.postenable = &st_magn_buffer_postenable,
.predisable = &st_magn_buffer_predisable,
};
int st_magn_allocate_ring(struct iio_dev *indio_dev)
{
iio: st_sensors: switch to a threaded interrupt commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded ("iio: st_sensors: verify interrupt event to status") caused a regression when reading ST sensors from a HRTimer trigger rather than the intrinsic interrupts: the HRTimer may trigger faster than the sensor provides new values, and as the check against new values available as a cause of the interrupt trigger was done in the poll function, this would bail out of the HRTimer interrupt with IRQ_NONE. So clearly we need to only check the new values available from the proper interrupt handler and not from the poll function, which should rather just read the raw values from the registers, put them into the buffer and be happy. To achieve this: switch the ST Sensors over to using a true threaded interrupt handler. In the interrupt thread, check if new values are available, else yield to the (potential) next device on the same interrupt line to check the registers. If the interrupt was ours, proceed to poll the values. Instead of relying on iio_trigger_generic_data_rdy_poll() as a top half to wake up the thread that polls the sensor for new data, have the thread call iio_trigger_poll_chained() after determining that is is the proper source of the interrupt. This is modelled on drivers/iio/accel/mma8452.c which is already using a properly threaded interrupt handler. In order to get the same precision in timestamps as previously, where samples would be timestamped in the poll function pf->timestamp when calling iio_trigger_generic_data_rdy_poll() we introduce a local timestamp in the sensor data, set it in the top half (fastpath) of the interrupt handler and provide that to the core when calling iio_push_to_buffers_with_timestamp(). Additionally: if the active scanmask is not set for the sensor no IRQs should be enabled and we need to bail out with IRQ_NONE. This can happen if spurious IRQs fire when installing the threaded interrupt handler. Tested with hard interrupt triggers on LIS331DL, then also tested with hrtimers on the same sensor by creating a 75Hz HRTimer and using it to poll the sensor. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Giuseppe Barba <giuseppe.barba@st.com> Cc: Denis Ciocca <denis.ciocca@st.com> Reported-by: Crestez Dan Leonard <cdleonard@gmail.com> Tested-by: Crestez Dan Leonard <cdleonard@gmail.com> Tested-by: Jonathan Cameron <jic23@kernel.org> Fixes: 97865fe41322 ("iio: st_sensors: verify interrupt event to status") Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-05-22 02:43:16 +08:00
return iio_triggered_buffer_setup(indio_dev, NULL,
&st_sensors_trigger_handler, &st_magn_buffer_setup_ops);
}
void st_magn_deallocate_ring(struct iio_dev *indio_dev)
{
iio_triggered_buffer_cleanup(indio_dev);
}
MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>");
MODULE_DESCRIPTION("STMicroelectronics magnetometers buffer");
MODULE_LICENSE("GPL v2");