UbiquitousOS
/
OpenCloudOS-Kernel
mirror of https://gitee.com/OpenCloudOS/OpenCloudOS-Kernel.git
11
0
Fork 0
Code Issues Projects Releases Wiki Activity
OpenCloudOS-Kernel/drivers/thermal/intel/intel_quark_dts_thermal.c

447 lines
12 KiB
C
Raw Normal View History

thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
/*
* intel_quark_dts_thermal.c
*
* This file is provided under a dual BSD/GPLv2 license. When using or
* redistributing this file, you may do so under either license.
*
* GPL LICENSE SUMMARY
*
* Copyright(c) 2015 Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* Contact Information:
* Ong Boon Leong <boon.leong.ong@intel.com>
* Intel Malaysia, Penang
*
* BSD LICENSE
*
* Copyright(c) 2015 Intel Corporation.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name of Intel Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* Quark DTS thermal driver is implemented by referencing
* intel_soc_dts_thermal.c.
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/thermal.h>
#include <asm/cpu_device_id.h>
#include <asm/iosf_mbi.h>
/* DTS reset is programmed via QRK_MBI_UNIT_SOC */
#define QRK_DTS_REG_OFFSET_RESET 0x34
#define QRK_DTS_RESET_BIT BIT(0)
/* DTS enable is programmed via QRK_MBI_UNIT_RMU */
#define QRK_DTS_REG_OFFSET_ENABLE 0xB0
#define QRK_DTS_ENABLE_BIT BIT(15)
/* Temperature Register is read via QRK_MBI_UNIT_RMU */
#define QRK_DTS_REG_OFFSET_TEMP 0xB1
#define QRK_DTS_MASK_TEMP 0xFF
#define QRK_DTS_OFFSET_TEMP 0
#define QRK_DTS_OFFSET_REL_TEMP 16
#define QRK_DTS_TEMP_BASE 50
/* Programmable Trip Point Register is configured via QRK_MBI_UNIT_RMU */
#define QRK_DTS_REG_OFFSET_PTPS 0xB2
#define QRK_DTS_MASK_TP_THRES 0xFF
#define QRK_DTS_SHIFT_TP 8
#define QRK_DTS_ID_TP_CRITICAL 0
#define QRK_DTS_SAFE_TP_THRES 105
/* Thermal Sensor Register Lock */
#define QRK_DTS_REG_OFFSET_LOCK 0x71
#define QRK_DTS_LOCK_BIT BIT(5)
/* Quark DTS has 2 trip points: hot & catastrophic */
#define QRK_MAX_DTS_TRIPS 2
/* If DTS not locked, all trip points are configurable */
#define QRK_DTS_WR_MASK_SET 0x3
/* If DTS locked, all trip points are not configurable */
#define QRK_DTS_WR_MASK_CLR 0
#define DEFAULT_POLL_DELAY 2000
struct soc_sensor_entry {
bool locked;
u32 store_ptps;
u32 store_dts_enable;
struct thermal_zone_device *tzone;
};
static struct soc_sensor_entry *soc_dts;
static int polling_delay = DEFAULT_POLL_DELAY;
module_param(polling_delay, int, 0644);
MODULE_PARM_DESC(polling_delay,
"Polling interval for checking trip points (in milliseconds)");
static DEFINE_MUTEX(dts_update_mutex);
static int soc_dts_enable(struct thermal_zone_device *tzd)
{
u32 out;
struct soc_sensor_entry *aux_entry = tzd->devdata;
int ret;
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
ret = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_ENABLE, &out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (ret)
return ret;
thermal: Use mode helpers in drivers Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled(). Consequently, all set_mode() implementations in drivers: - can stop modifying tzd's "mode" member, - shall stop taking tzd's lock, as it is taken in the helpers - shall stop calling thermal_zone_device_update() as it is called in the helpers - can assume they are called when the mode truly changes, so checks to verify that can be dropped Not providing set_mode() by a driver no longer prevents the core from being able to set tzd's mode, so the relevant check in mode_store() is removed. Other comments: - acpi/thermal.c: tz->thermal_zone->mode will be updated only after we return from set_mode(), so use function parameter in thermal_set_mode() instead, no need to call acpi_thermal_check() in set_mode() - thermal/imx_thermal.c: regmap writes and mode assignment are done in thermal_zone_device_{en|dis}able() and set_mode() callback - thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a part of set_mode() callback, so they don't need to modify tzd->mode, and don't need to fall back to the opposite mode if unsuccessful, as the return value will be propagated to thermal_zone_device_{en|dis}able() and ultimately tzd's member will not be changed in thermal_zone_device_set_mode(). - thermal/of-thermal.c: no need to set zone->mode to DISABLED in of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
2020-06-29 20:29:21 +08:00
if (out & QRK_DTS_ENABLE_BIT)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
return 0;
if (!aux_entry->locked) {
out |= QRK_DTS_ENABLE_BIT;
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
ret = iosf_mbi_write(QRK_MBI_UNIT_RMU, MBI_REG_WRITE,
QRK_DTS_REG_OFFSET_ENABLE, out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (ret)
return ret;
} else {
pr_info("DTS is locked. Cannot enable DTS\n");
ret = -EPERM;
}
return ret;
}
static int soc_dts_disable(struct thermal_zone_device *tzd)
{
u32 out;
struct soc_sensor_entry *aux_entry = tzd->devdata;
int ret;
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
ret = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_ENABLE, &out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (ret)
return ret;
thermal: Use mode helpers in drivers Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled(). Consequently, all set_mode() implementations in drivers: - can stop modifying tzd's "mode" member, - shall stop taking tzd's lock, as it is taken in the helpers - shall stop calling thermal_zone_device_update() as it is called in the helpers - can assume they are called when the mode truly changes, so checks to verify that can be dropped Not providing set_mode() by a driver no longer prevents the core from being able to set tzd's mode, so the relevant check in mode_store() is removed. Other comments: - acpi/thermal.c: tz->thermal_zone->mode will be updated only after we return from set_mode(), so use function parameter in thermal_set_mode() instead, no need to call acpi_thermal_check() in set_mode() - thermal/imx_thermal.c: regmap writes and mode assignment are done in thermal_zone_device_{en|dis}able() and set_mode() callback - thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a part of set_mode() callback, so they don't need to modify tzd->mode, and don't need to fall back to the opposite mode if unsuccessful, as the return value will be propagated to thermal_zone_device_{en|dis}able() and ultimately tzd's member will not be changed in thermal_zone_device_set_mode(). - thermal/of-thermal.c: no need to set zone->mode to DISABLED in of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
2020-06-29 20:29:21 +08:00
if (!(out & QRK_DTS_ENABLE_BIT))
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
return 0;
if (!aux_entry->locked) {
out &= ~QRK_DTS_ENABLE_BIT;
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
ret = iosf_mbi_write(QRK_MBI_UNIT_RMU, MBI_REG_WRITE,
QRK_DTS_REG_OFFSET_ENABLE, out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (ret)
return ret;
} else {
pr_info("DTS is locked. Cannot disable DTS\n");
ret = -EPERM;
}
return ret;
}
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 14:12:54 +08:00
static int _get_trip_temp(int trip, int *temp)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{
int status;
u32 out;
mutex_lock(&dts_update_mutex);
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
status = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_PTPS, &out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
mutex_unlock(&dts_update_mutex);
if (status)
return status;
/*
* Thermal Sensor Programmable Trip Point Register has 8-bit
* fields for critical (catastrophic) and hot set trip point
* thresholds. The threshold value is always offset by its
* temperature base (50 degree Celsius).
*/
*temp = (out >> (trip * QRK_DTS_SHIFT_TP)) & QRK_DTS_MASK_TP_THRES;
*temp -= QRK_DTS_TEMP_BASE;
return 0;
}
static inline int sys_get_trip_temp(struct thermal_zone_device *tzd,
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 14:12:54 +08:00
int trip, int *temp)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{
return _get_trip_temp(trip, temp);
}
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 14:12:54 +08:00
static inline int sys_get_crit_temp(struct thermal_zone_device *tzd, int *temp)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{
return _get_trip_temp(QRK_DTS_ID_TP_CRITICAL, temp);
}
static int update_trip_temp(struct soc_sensor_entry *aux_entry,
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 14:12:54 +08:00
int trip, int temp)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{
u32 out;
u32 temp_out;
u32 store_ptps;
int ret;
mutex_lock(&dts_update_mutex);
if (aux_entry->locked) {
ret = -EPERM;
goto failed;
}
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
ret = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_PTPS, &store_ptps);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (ret)
goto failed;
/*
* Protection against unsafe trip point thresdhold value.
* As Quark X1000 data-sheet does not provide any recommendation
* regarding the safe trip point threshold value to use, we choose
* the safe value according to the threshold value set by UEFI BIOS.
*/
if (temp > QRK_DTS_SAFE_TP_THRES)
temp = QRK_DTS_SAFE_TP_THRES;
/*
* Thermal Sensor Programmable Trip Point Register has 8-bit
* fields for critical (catastrophic) and hot set trip point
* thresholds. The threshold value is always offset by its
* temperature base (50 degree Celsius).
*/
temp_out = temp + QRK_DTS_TEMP_BASE;
out = (store_ptps & ~(QRK_DTS_MASK_TP_THRES <<
(trip * QRK_DTS_SHIFT_TP)));
out |= (temp_out & QRK_DTS_MASK_TP_THRES) <<
(trip * QRK_DTS_SHIFT_TP);
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
ret = iosf_mbi_write(QRK_MBI_UNIT_RMU, MBI_REG_WRITE,
QRK_DTS_REG_OFFSET_PTPS, out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
failed:
mutex_unlock(&dts_update_mutex);
return ret;
}
static inline int sys_set_trip_temp(struct thermal_zone_device *tzd, int trip,
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 14:12:54 +08:00
int temp)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{
return update_trip_temp(tzd->devdata, trip, temp);
}
static int sys_get_trip_type(struct thermal_zone_device *thermal,
int trip, enum thermal_trip_type *type)
{
if (trip)
*type = THERMAL_TRIP_HOT;
else
*type = THERMAL_TRIP_CRITICAL;
return 0;
}
static int sys_get_curr_temp(struct thermal_zone_device *tzd,
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 14:12:54 +08:00
int *temp)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{
u32 out;
int ret;
mutex_lock(&dts_update_mutex);
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
ret = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_TEMP, &out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
mutex_unlock(&dts_update_mutex);
if (ret)
return ret;
/*
* Thermal Sensor Temperature Register has 8-bit field
* for temperature value (offset by temperature base
* 50 degree Celsius).
*/
out = (out >> QRK_DTS_OFFSET_TEMP) & QRK_DTS_MASK_TEMP;
*temp = out - QRK_DTS_TEMP_BASE;
return 0;
}
thermal: Rename set_mode() to change_mode() set_mode() is only called when tzd's mode is about to change. Actual setting is performed in thermal_core, in thermal_zone_device_set_mode(). The meaning of set_mode() callback is actually to notify the driver about the mode being changed and giving the driver a chance to oppose such change. To better reflect the purpose of the method rename it to change_mode() Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-12-andrzej.p@collabora.com
2020-06-29 20:29:25 +08:00
static int sys_change_mode(struct thermal_zone_device *tzd,
enum thermal_device_mode mode)
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{
int ret;
mutex_lock(&dts_update_mutex);
if (mode == THERMAL_DEVICE_ENABLED)
ret = soc_dts_enable(tzd);
else
ret = soc_dts_disable(tzd);
mutex_unlock(&dts_update_mutex);
return ret;
}
static struct thermal_zone_device_ops tzone_ops = {
.get_temp = sys_get_curr_temp,
.get_trip_temp = sys_get_trip_temp,
.get_trip_type = sys_get_trip_type,
.set_trip_temp = sys_set_trip_temp,
.get_crit_temp = sys_get_crit_temp,
thermal: Rename set_mode() to change_mode() set_mode() is only called when tzd's mode is about to change. Actual setting is performed in thermal_core, in thermal_zone_device_set_mode(). The meaning of set_mode() callback is actually to notify the driver about the mode being changed and giving the driver a chance to oppose such change. To better reflect the purpose of the method rename it to change_mode() Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-12-andrzej.p@collabora.com
2020-06-29 20:29:25 +08:00
.change_mode = sys_change_mode,
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
};
static void free_soc_dts(struct soc_sensor_entry *aux_entry)
{
if (aux_entry) {
if (!aux_entry->locked) {
mutex_lock(&dts_update_mutex);
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
iosf_mbi_write(QRK_MBI_UNIT_RMU, MBI_REG_WRITE,
QRK_DTS_REG_OFFSET_ENABLE,
aux_entry->store_dts_enable);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
iosf_mbi_write(QRK_MBI_UNIT_RMU, MBI_REG_WRITE,
QRK_DTS_REG_OFFSET_PTPS,
aux_entry->store_ptps);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
mutex_unlock(&dts_update_mutex);
}
thermal_zone_device_unregister(aux_entry->tzone);
kfree(aux_entry);
}
}
static struct soc_sensor_entry *alloc_soc_dts(void)
{
struct soc_sensor_entry *aux_entry;
int err;
u32 out;
int wr_mask;
aux_entry = kzalloc(sizeof(*aux_entry), GFP_KERNEL);
if (!aux_entry) {
err = -ENOMEM;
return ERR_PTR(-ENOMEM);
}
/* Check if DTS register is locked */
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
err = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_LOCK, &out);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (err)
goto err_ret;
if (out & QRK_DTS_LOCK_BIT) {
aux_entry->locked = true;
wr_mask = QRK_DTS_WR_MASK_CLR;
} else {
aux_entry->locked = false;
wr_mask = QRK_DTS_WR_MASK_SET;
}
/* Store DTS default state if DTS registers are not locked */
if (!aux_entry->locked) {
/* Store DTS default enable for restore on exit */
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
err = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_ENABLE,
&aux_entry->store_dts_enable);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (err)
goto err_ret;
/* Store DTS default PTPS register for restore on exit */
x86/platform/iosf_mbi: Remove duplicate definitions The read and write opcodes are global for all units on SoC and even across Intel SoCs. Remove duplication of corresponding constants. At the same time convert all current users. No functional change. Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Boon Leong Ong <boon.leong.ong@intel.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-12 01:59:29 +08:00
err = iosf_mbi_read(QRK_MBI_UNIT_RMU, MBI_REG_READ,
QRK_DTS_REG_OFFSET_PTPS,
&aux_entry->store_ptps);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (err)
goto err_ret;
}
aux_entry->tzone = thermal_zone_device_register("quark_dts",
QRK_MAX_DTS_TRIPS,
wr_mask,
aux_entry, &tzone_ops, NULL, 0, polling_delay);
if (IS_ERR(aux_entry->tzone)) {
err = PTR_ERR(aux_entry->tzone);
goto err_ret;
}
thermal: Use mode helpers in drivers Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled(). Consequently, all set_mode() implementations in drivers: - can stop modifying tzd's "mode" member, - shall stop taking tzd's lock, as it is taken in the helpers - shall stop calling thermal_zone_device_update() as it is called in the helpers - can assume they are called when the mode truly changes, so checks to verify that can be dropped Not providing set_mode() by a driver no longer prevents the core from being able to set tzd's mode, so the relevant check in mode_store() is removed. Other comments: - acpi/thermal.c: tz->thermal_zone->mode will be updated only after we return from set_mode(), so use function parameter in thermal_set_mode() instead, no need to call acpi_thermal_check() in set_mode() - thermal/imx_thermal.c: regmap writes and mode assignment are done in thermal_zone_device_{en|dis}able() and set_mode() callback - thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a part of set_mode() callback, so they don't need to modify tzd->mode, and don't need to fall back to the opposite mode if unsuccessful, as the return value will be propagated to thermal_zone_device_{en|dis}able() and ultimately tzd's member will not be changed in thermal_zone_device_set_mode(). - thermal/of-thermal.c: no need to set zone->mode to DISABLED in of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
2020-06-29 20:29:21 +08:00
err = thermal_zone_device_enable(aux_entry->tzone);
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
if (err)
goto err_aux_status;
return aux_entry;
err_aux_status:
thermal_zone_device_unregister(aux_entry->tzone);
err_ret:
kfree(aux_entry);
return ERR_PTR(err);
}
static const struct x86_cpu_id qrk_thermal_ids[] __initconst = {
thermal: Convert to new X86 CPU match macros The new macro set has a consistent namespace and uses C99 initializers instead of the grufty C89 ones. Get rid the of the local QUARK defines and use the proper ones. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lkml.kernel.org/r/20200320131509.967017771@linutronix.de
2020-03-20 21:13:58 +08:00
X86_MATCH_VENDOR_FAM_MODEL(INTEL, 5, INTEL_FAM5_QUARK_X1000, NULL),
thermal: intel Quark SoC X1000 DTS thermal driver In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS). The DTS offers both hot & critical trip points. However, in current distribution of UEFI BIOS for Quark platform, only critical trip point is configured to be 105 degree Celsius (based on Quark SW ver1.0.1 and hot trip point is not used due to lack of IRQ. There is no active cooling device for Quark SoC, so Quark SoC thermal management logic expects Linux distro to orderly power-off when temperature of the DTS exceeds the configured critical trip point. Kernel param "polling_delay" in milliseconds is used to control the frequency the DTS temperature is read by thermal framework. It defaults to 2-second. To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X". User interacts with Quark SoC DTS thermal driver through sysfs via: /sys/class/thermal/thermal_zone0/ For example: - to read DTS temperature $ cat temp - to read critical trip point $ cat trip_point_0_temp - to read trip point type $ cat trip_point_0_type - to emulate temperature raise to test orderly shutdown by Linux distro $ echo 105 > emul_temp Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-04-15 10:08:15 +08:00
{}
};
MODULE_DEVICE_TABLE(x86cpu, qrk_thermal_ids);
static int __init intel_quark_thermal_init(void)
{
int err = 0;
if (!x86_match_cpu(qrk_thermal_ids) || !iosf_mbi_available())
return -ENODEV;
soc_dts = alloc_soc_dts();
if (IS_ERR(soc_dts)) {
err = PTR_ERR(soc_dts);
goto err_free;
}
return 0;
err_free:
free_soc_dts(soc_dts);
return err;
}
static void __exit intel_quark_thermal_exit(void)
{
free_soc_dts(soc_dts);
}
module_init(intel_quark_thermal_init)
module_exit(intel_quark_thermal_exit)
MODULE_DESCRIPTION("Intel Quark DTS Thermal Driver");
MODULE_AUTHOR("Ong Boon Leong <boon.leong.ong@intel.com>");
MODULE_LICENSE("Dual BSD/GPL");