License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
|
|
|
/* SPDX-License-Identifier: GPL-2.0 */
|
powerpc/xmon: Fix SPR read/write commands and add command to dump SPRs
xmon has commands for reading and writing SPRs, but they don't work
currently for several reasons. They attempt to synthesize a small
function containing an mfspr or mtspr instruction and call it. However,
the instructions are on the stack, which is usually not executable.
Also, for 64-bit we set up a procedure descriptor, which is fine for the
big-endian ABIv1, but not correct for ABIv2. Finally, the code uses the
infrastructure for catching memory errors, but that only catches data
storage interrupts and machine check interrupts, but a failed
mfspr/mtspr can generate a program interrupt or a hypervisor emulation
assist interrupt, or be a no-op.
Instead of trying to synthesize a function on the fly, this adds two new
functions, xmon_mfspr() and xmon_mtspr(), which take an SPR number as an
argument and read or write the SPR. Because there is no Power ISA
instruction which takes an SPR number in a register, we have to generate
one of each possible mfspr and mtspr instruction, for all 1024 possible
SPRs. Thus we get just over 8k bytes of code for each of xmon_mfspr()
and xmon_mtspr(). However, this 16kB of code pales in comparison to the
> 130kB of PPC opcode tables used by the xmon disassembler.
To catch interrupts caused by the mfspr/mtspr instructions, we add a new
'catch_spr_faults' flag. If an interrupt occurs while it is set, we come
back into xmon() via program_check_interrupt(), _exception() and die(),
see that catch_spr_faults is set and do a longjmp to bus_error_jmp, back
into read_spr() or write_spr().
This adds a couple of other nice features: first, a "Sa" command that
attempts to read and print out the value of all 1024 SPRs. If any mfspr
instruction acts as a no-op, then the SPR is not implemented and not
printed.
Secondly, the Sr and Sw commands detect when an SPR is not
implemented (i.e. mfspr is a no-op) and print a message to that effect
rather than printing a bogus value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-04-13 19:31:24 +08:00
|
|
|
#include <asm/ppc_asm.h>
|
2018-07-06 00:24:57 +08:00
|
|
|
#include <asm/asm-compat.h>
|
powerpc/xmon: Fix SPR read/write commands and add command to dump SPRs
xmon has commands for reading and writing SPRs, but they don't work
currently for several reasons. They attempt to synthesize a small
function containing an mfspr or mtspr instruction and call it. However,
the instructions are on the stack, which is usually not executable.
Also, for 64-bit we set up a procedure descriptor, which is fine for the
big-endian ABIv1, but not correct for ABIv2. Finally, the code uses the
infrastructure for catching memory errors, but that only catches data
storage interrupts and machine check interrupts, but a failed
mfspr/mtspr can generate a program interrupt or a hypervisor emulation
assist interrupt, or be a no-op.
Instead of trying to synthesize a function on the fly, this adds two new
functions, xmon_mfspr() and xmon_mtspr(), which take an SPR number as an
argument and read or write the SPR. Because there is no Power ISA
instruction which takes an SPR number in a register, we have to generate
one of each possible mfspr and mtspr instruction, for all 1024 possible
SPRs. Thus we get just over 8k bytes of code for each of xmon_mfspr()
and xmon_mtspr(). However, this 16kB of code pales in comparison to the
> 130kB of PPC opcode tables used by the xmon disassembler.
To catch interrupts caused by the mfspr/mtspr instructions, we add a new
'catch_spr_faults' flag. If an interrupt occurs while it is set, we come
back into xmon() via program_check_interrupt(), _exception() and die(),
see that catch_spr_faults is set and do a longjmp to bus_error_jmp, back
into read_spr() or write_spr().
This adds a couple of other nice features: first, a "Sa" command that
attempts to read and print out the value of all 1024 SPRs. If any mfspr
instruction acts as a no-op, then the SPR is not implemented and not
printed.
Secondly, the Sr and Sw commands detect when an SPR is not
implemented (i.e. mfspr is a no-op) and print a message to that effect
rather than printing a bogus value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-04-13 19:31:24 +08:00
|
|
|
|
|
|
|
|
/* unsigned long xmon_mfspr(sprn, default_value) */
|
|
|
|
|
_GLOBAL(xmon_mfspr)
|
2016-09-09 12:01:07 +08:00
|
|
|
PPC_LL r5, .Lmfspr_table@got(r2)
|
powerpc/xmon: Fix SPR read/write commands and add command to dump SPRs
xmon has commands for reading and writing SPRs, but they don't work
currently for several reasons. They attempt to synthesize a small
function containing an mfspr or mtspr instruction and call it. However,
the instructions are on the stack, which is usually not executable.
Also, for 64-bit we set up a procedure descriptor, which is fine for the
big-endian ABIv1, but not correct for ABIv2. Finally, the code uses the
infrastructure for catching memory errors, but that only catches data
storage interrupts and machine check interrupts, but a failed
mfspr/mtspr can generate a program interrupt or a hypervisor emulation
assist interrupt, or be a no-op.
Instead of trying to synthesize a function on the fly, this adds two new
functions, xmon_mfspr() and xmon_mtspr(), which take an SPR number as an
argument and read or write the SPR. Because there is no Power ISA
instruction which takes an SPR number in a register, we have to generate
one of each possible mfspr and mtspr instruction, for all 1024 possible
SPRs. Thus we get just over 8k bytes of code for each of xmon_mfspr()
and xmon_mtspr(). However, this 16kB of code pales in comparison to the
> 130kB of PPC opcode tables used by the xmon disassembler.
To catch interrupts caused by the mfspr/mtspr instructions, we add a new
'catch_spr_faults' flag. If an interrupt occurs while it is set, we come
back into xmon() via program_check_interrupt(), _exception() and die(),
see that catch_spr_faults is set and do a longjmp to bus_error_jmp, back
into read_spr() or write_spr().
This adds a couple of other nice features: first, a "Sa" command that
attempts to read and print out the value of all 1024 SPRs. If any mfspr
instruction acts as a no-op, then the SPR is not implemented and not
printed.
Secondly, the Sr and Sw commands detect when an SPR is not
implemented (i.e. mfspr is a no-op) and print a message to that effect
rather than printing a bogus value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-04-13 19:31:24 +08:00
|
|
|
b xmon_mxspr
|
|
|
|
|
|
|
|
|
|
/* void xmon_mtspr(sprn, new_value) */
|
|
|
|
|
_GLOBAL(xmon_mtspr)
|
2016-09-09 12:01:07 +08:00
|
|
|
PPC_LL r5, .Lmtspr_table@got(r2)
|
powerpc/xmon: Fix SPR read/write commands and add command to dump SPRs
xmon has commands for reading and writing SPRs, but they don't work
currently for several reasons. They attempt to synthesize a small
function containing an mfspr or mtspr instruction and call it. However,
the instructions are on the stack, which is usually not executable.
Also, for 64-bit we set up a procedure descriptor, which is fine for the
big-endian ABIv1, but not correct for ABIv2. Finally, the code uses the
infrastructure for catching memory errors, but that only catches data
storage interrupts and machine check interrupts, but a failed
mfspr/mtspr can generate a program interrupt or a hypervisor emulation
assist interrupt, or be a no-op.
Instead of trying to synthesize a function on the fly, this adds two new
functions, xmon_mfspr() and xmon_mtspr(), which take an SPR number as an
argument and read or write the SPR. Because there is no Power ISA
instruction which takes an SPR number in a register, we have to generate
one of each possible mfspr and mtspr instruction, for all 1024 possible
SPRs. Thus we get just over 8k bytes of code for each of xmon_mfspr()
and xmon_mtspr(). However, this 16kB of code pales in comparison to the
> 130kB of PPC opcode tables used by the xmon disassembler.
To catch interrupts caused by the mfspr/mtspr instructions, we add a new
'catch_spr_faults' flag. If an interrupt occurs while it is set, we come
back into xmon() via program_check_interrupt(), _exception() and die(),
see that catch_spr_faults is set and do a longjmp to bus_error_jmp, back
into read_spr() or write_spr().
This adds a couple of other nice features: first, a "Sa" command that
attempts to read and print out the value of all 1024 SPRs. If any mfspr
instruction acts as a no-op, then the SPR is not implemented and not
printed.
Secondly, the Sr and Sw commands detect when an SPR is not
implemented (i.e. mfspr is a no-op) and print a message to that effect
rather than printing a bogus value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-04-13 19:31:24 +08:00
|
|
|
b xmon_mxspr
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* r3 = sprn
|
|
|
|
|
* r4 = default or new value
|
|
|
|
|
* r5 = table base
|
|
|
|
|
*/
|
|
|
|
|
xmon_mxspr:
|
|
|
|
|
/*
|
|
|
|
|
* To index into the table of mxsprs we need:
|
|
|
|
|
* i = (sprn & 0x3ff) * 8
|
|
|
|
|
* or using rwlinm:
|
|
|
|
|
* i = (sprn << 3) & (0x3ff << 3)
|
|
|
|
|
*/
|
|
|
|
|
rlwinm r3, r3, 3, 0x3ff << 3
|
|
|
|
|
add r5, r5, r3
|
|
|
|
|
mtctr r5
|
|
|
|
|
mr r3, r4 /* put default_value in r3 for mfspr */
|
|
|
|
|
bctr
|
|
|
|
|
|
|
|
|
|
.Lmfspr_table:
|
|
|
|
|
spr = 0
|
|
|
|
|
.rept 1024
|
|
|
|
|
mfspr r3, spr
|
|
|
|
|
blr
|
|
|
|
|
spr = spr + 1
|
|
|
|
|
.endr
|
|
|
|
|
|
|
|
|
|
.Lmtspr_table:
|
|
|
|
|
spr = 0
|
|
|
|
|
.rept 1024
|
|
|
|
|
mtspr spr, r4
|
|
|
|
|
blr
|
|
|
|
|
spr = spr + 1
|
|
|
|
|
.endr
|