OpenCloudOS-Kernel/Documentation/RCU/checklist.txt

Review Checklist for RCU Patches


This document contains a checklist for producing and reviewing patches
that make use of RCU.  Violating any of the rules listed below will
result in the same sorts of problems that leaving out a locking primitive
would cause.  This list is based on experiences reviewing such patches
over a rather long period of time, but improvements are always welcome!

0.	Is RCU being applied to a read-mostly situation?  If the data
	structure is updated more than about 10% of the time, then you
	should strongly consider some other approach, unless detailed
	performance measurements show that RCU is nonetheless the right
	tool for the job.  Yes, RCU does reduce read-side overhead by
	increasing write-side overhead, which is exactly why normal uses
	of RCU will do much more reading than updating.

	Another exception is where performance is not an issue, and RCU
	provides a simpler implementation.  An example of this situation
	is the dynamic NMI code in the Linux 2.6 kernel, at least on
	architectures where NMIs are rare.

	Yet another exception is where the low real-time latency of RCU's
	read-side primitives is critically important.

	One final exception is where RCU readers are used to prevent
	the ABA problem (https://en.wikipedia.org/wiki/ABA_problem)
	for lockless updates.  This does result in the mildly
	counter-intuitive situation where rcu_read_lock() and
	rcu_read_unlock() are used to protect updates, however, this
	approach provides the same potential simplifications that garbage
	collectors do.

1.	Does the update code have proper mutual exclusion?

	RCU does allow -readers- to run (almost) naked, but -writers- must
	still use some sort of mutual exclusion, such as:

	a.	locking,
	b.	atomic operations, or
	c.	restricting updates to a single task.

	If you choose #b, be prepared to describe how you have handled
	memory barriers on weakly ordered machines (pretty much all of
	them -- even x86 allows later loads to be reordered to precede
	earlier stores), and be prepared to explain why this added
	complexity is worthwhile.  If you choose #c, be prepared to
	explain how this single task does not become a major bottleneck on
	big multiprocessor machines (for example, if the task is updating
	information relating to itself that other tasks can read, there
	by definition can be no bottleneck).  Note that the definition
	of "large" has changed significantly:  Eight CPUs was "large"
	in the year 2000, but a hundred CPUs was unremarkable in 2017.

2.	Do the RCU read-side critical sections make proper use of
	rcu_read_lock() and friends?  These primitives are needed
	to prevent grace periods from ending prematurely, which
	could result in data being unceremoniously freed out from
	under your read-side code, which can greatly increase the
	actuarial risk of your kernel.

	As a rough rule of thumb, any dereference of an RCU-protected
	pointer must be covered by rcu_read_lock(), rcu_read_lock_bh(),
	rcu_read_lock_sched(), or by the appropriate update-side lock.
	Disabling of preemption can serve as rcu_read_lock_sched(), but
	is less readable and prevents lockdep from detecting locking issues.

	Letting RCU-protected pointers "leak" out of an RCU read-side
	critical section is every bid as bad as letting them leak out
	from under a lock.  Unless, of course, you have arranged some
	other means of protection, such as a lock or a reference count
	-before- letting them out of the RCU read-side critical section.

3.	Does the update code tolerate concurrent accesses?

	The whole point of RCU is to permit readers to run without
	any locks or atomic operations.  This means that readers will
	be running while updates are in progress.  There are a number
	of ways to handle this concurrency, depending on the situation:

	a.	Use the RCU variants of the list and hlist update
		primitives to add, remove, and replace elements on
		an RCU-protected list.	Alternatively, use the other
		RCU-protected data structures that have been added to
		the Linux kernel.

		This is almost always the best approach.

	b.	Proceed as in (a) above, but also maintain per-element
		locks (that are acquired by both readers and writers)
		that guard per-element state.  Of course, fields that
		the readers refrain from accessing can be guarded by
		some other lock acquired only by updaters, if desired.

		This works quite well, also.

	c.	Make updates appear atomic to readers.	For example,
		pointer updates to properly aligned fields will
		appear atomic, as will individual atomic primitives.
		Sequences of operations performed under a lock will -not-
		appear to be atomic to RCU readers, nor will sequences
		of multiple atomic primitives.

		This can work, but is starting to get a bit tricky.

	d.	Carefully order the updates and the reads so that
		readers see valid data at all phases of the update.
		This is often more difficult than it sounds, especially
		given modern CPUs' tendency to reorder memory references.
		One must usually liberally sprinkle memory barriers
		(smp_wmb(), smp_rmb(), smp_mb()) through the code,
		making it difficult to understand and to test.

		It is usually better to group the changing data into
		a separate structure, so that the change may be made
		to appear atomic by updating a pointer to reference
		a new structure containing updated values.

4.	Weakly ordered CPUs pose special challenges.  Almost all CPUs
	are weakly ordered -- even x86 CPUs allow later loads to be
	reordered to precede earlier stores.  RCU code must take all of
	the following measures to prevent memory-corruption problems:

	a.	Readers must maintain proper ordering of their memory
		accesses.  The rcu_dereference() primitive ensures that
		the CPU picks up the pointer before it picks up the data
		that the pointer points to.  This really is necessary
		on Alpha CPUs.	If you don't believe me, see:

			http://www.openvms.compaq.com/wizard/wiz_2637.html

		The rcu_dereference() primitive is also an excellent
		documentation aid, letting the person reading the
		code know exactly which pointers are protected by RCU.
		Please note that compilers can also reorder code, and
		they are becoming increasingly aggressive about doing
		just that.  The rcu_dereference() primitive therefore also
		prevents destructive compiler optimizations.  However,
		with a bit of devious creativity, it is possible to
		mishandle the return value from rcu_dereference().
		Please see rcu_dereference.txt in this directory for
		more information.

		The rcu_dereference() primitive is used by the
		various "_rcu()" list-traversal primitives, such
		as the list_for_each_entry_rcu().  Note that it is
		perfectly legal (if redundant) for update-side code to
		use rcu_dereference() and the "_rcu()" list-traversal
		primitives.  This is particularly useful in code that
		is common to readers and updaters.  However, lockdep
		will complain if you access rcu_dereference() outside
		of an RCU read-side critical section.  See lockdep.txt
		to learn what to do about this.

		Of course, neither rcu_dereference() nor the "_rcu()"
		list-traversal primitives can substitute for a good
		concurrency design coordinating among multiple updaters.

	b.	If the list macros are being used, the list_add_tail_rcu()
		and list_add_rcu() primitives must be used in order
		to prevent weakly ordered machines from misordering
		structure initialization and pointer planting.
		Similarly, if the hlist macros are being used, the
		hlist_add_head_rcu() primitive is required.

	c.	If the list macros are being used, the list_del_rcu()
		primitive must be used to keep list_del()'s pointer
		poisoning from inflicting toxic effects on concurrent
		readers.  Similarly, if the hlist macros are being used,
		the hlist_del_rcu() primitive is required.

		The list_replace_rcu() and hlist_replace_rcu() primitives
		may be used to replace an old structure with a new one
		in their respective types of RCU-protected lists.

	d.	Rules similar to (4b) and (4c) apply to the "hlist_nulls"
		type of RCU-protected linked lists.

	e.	Updates must ensure that initialization of a given
		structure happens before pointers to that structure are
		publicized.  Use the rcu_assign_pointer() primitive
		when publicizing a pointer to a structure that can
		be traversed by an RCU read-side critical section.

5.	If call_rcu() or call_srcu() is used, the callback function will
	be called from softirq context.  In particular, it cannot block.

6.	Since synchronize_rcu() can block, it cannot be called
	from any sort of irq context.  The same rule applies
	for synchronize_srcu(), synchronize_rcu_expedited(), and
	synchronize_srcu_expedited().

	The expedited forms of these primitives have the same semantics
	as the non-expedited forms, but expediting is both expensive and
	(with the exception of synchronize_srcu_expedited()) unfriendly
	to real-time workloads.  Use of the expedited primitives should
	be restricted to rare configuration-change operations that would
	not normally be undertaken while a real-time workload is running.
	However, real-time workloads can use rcupdate.rcu_normal kernel
	boot parameter to completely disable expedited grace periods,
	though this might have performance implications.

	In particular, if you find yourself invoking one of the expedited
	primitives repeatedly in a loop, please do everyone a favor:
	Restructure your code so that it batches the updates, allowing
	a single non-expedited primitive to cover the entire batch.
	This will very likely be faster than the loop containing the
	expedited primitive, and will be much much easier on the rest
	of the system, especially to real-time workloads running on
	the rest of the system.

7.	As of v4.20, a given kernel implements only one RCU flavor,
	which is RCU-sched for PREEMPT=n and RCU-preempt for PREEMPT=y.
	If the updater uses call_rcu() or synchronize_rcu(),
	then the corresponding readers my use rcu_read_lock() and
	rcu_read_unlock(), rcu_read_lock_bh() and rcu_read_unlock_bh(),
	or any pair of primitives that disables and re-enables preemption,
	for example, rcu_read_lock_sched() and rcu_read_unlock_sched().
	If the updater uses synchronize_srcu() or call_srcu(),
	then the corresponding readers must use srcu_read_lock() and
	srcu_read_unlock(), and with the same srcu_struct.  The rules for
	the expedited primitives are the same as for their non-expedited
	counterparts.  Mixing things up will result in confusion and
	broken kernels, and has even resulted in an exploitable security
	issue.

	One exception to this rule: rcu_read_lock() and rcu_read_unlock()
	may be substituted for rcu_read_lock_bh() and rcu_read_unlock_bh()
	in cases where local bottom halves are already known to be
	disabled, for example, in irq or softirq context.  Commenting
	such cases is a must, of course!  And the jury is still out on
	whether the increased speed is worth it.

8.	Although synchronize_rcu() is slower than is call_rcu(), it
	usually results in simpler code.  So, unless update performance is
	critically important, the updaters cannot block, or the latency of
	synchronize_rcu() is visible from userspace, synchronize_rcu()
	should be used in preference to call_rcu().  Furthermore,
	kfree_rcu() usually results in even simpler code than does
	synchronize_rcu() without synchronize_rcu()'s multi-millisecond
	latency.  So please take advantage of kfree_rcu()'s "fire and
	forget" memory-freeing capabilities where it applies.

	An especially important property of the synchronize_rcu()
	primitive is that it automatically self-limits: if grace periods
	are delayed for whatever reason, then the synchronize_rcu()
	primitive will correspondingly delay updates.  In contrast,
	code using call_rcu() should explicitly limit update rate in
	cases where grace periods are delayed, as failing to do so can
	result in excessive realtime latencies or even OOM conditions.

	Ways of gaining this self-limiting property when using call_rcu()
	include:

	a.	Keeping a count of the number of data-structure elements
		used by the RCU-protected data structure, including
		those waiting for a grace period to elapse.  Enforce a
		limit on this number, stalling updates as needed to allow
		previously deferred frees to complete.	Alternatively,
		limit only the number awaiting deferred free rather than
		the total number of elements.

		One way to stall the updates is to acquire the update-side
		mutex.	(Don't try this with a spinlock -- other CPUs
		spinning on the lock could prevent the grace period
		from ever ending.)  Another way to stall the updates
		is for the updates to use a wrapper function around
		the memory allocator, so that this wrapper function
		simulates OOM when there is too much memory awaiting an
		RCU grace period.  There are of course many other
		variations on this theme.

	b.	Limiting update rate.  For example, if updates occur only
		once per hour, then no explicit rate limiting is
		required, unless your system is already badly broken.
		Older versions of the dcache subsystem take this approach,
		guarding updates with a global lock, limiting their rate.

	c.	Trusted update -- if updates can only be done manually by
		superuser or some other trusted user, then it might not
		be necessary to automatically limit them.  The theory
		here is that superuser already has lots of ways to crash
		the machine.

	d.	Periodically invoke synchronize_rcu(), permitting a limited
		number of updates per grace period.

	The same cautions apply to call_srcu() and kfree_rcu().

	Note that although these primitives do take action to avoid memory
	exhaustion when any given CPU has too many callbacks, a determined
	user could still exhaust memory.  This is especially the case
	if a system with a large number of CPUs has been configured to
	offload all of its RCU callbacks onto a single CPU, or if the
	system has relatively little free memory.

9.	All RCU list-traversal primitives, which include
	rcu_dereference(), list_for_each_entry_rcu(), and
	list_for_each_safe_rcu(), must be either within an RCU read-side
	critical section or must be protected by appropriate update-side
	locks.	RCU read-side critical sections are delimited by
	rcu_read_lock() and rcu_read_unlock(), or by similar primitives
	such as rcu_read_lock_bh() and rcu_read_unlock_bh(), in which
	case the matching rcu_dereference() primitive must be used in
	order to keep lockdep happy, in this case, rcu_dereference_bh().

	The reason that it is permissible to use RCU list-traversal
	primitives when the update-side lock is held is that doing so
	can be quite helpful in reducing code bloat when common code is
	shared between readers and updaters.  Additional primitives
	are provided for this case, as discussed in lockdep.txt.

10.	Conversely, if you are in an RCU read-side critical section,
	and you don't hold the appropriate update-side lock, you -must-
	use the "_rcu()" variants of the list macros.  Failing to do so
	will break Alpha, cause aggressive compilers to generate bad code,
	and confuse people trying to read your code.

11.	Any lock acquired by an RCU callback must be acquired elsewhere
	with softirq disabled, e.g., via spin_lock_irqsave(),
	spin_lock_bh(), etc.  Failing to disable softirq on a given
	acquisition of that lock will result in deadlock as soon as
	the RCU softirq handler happens to run your RCU callback while
	interrupting that acquisition's critical section.

12.	RCU callbacks can be and are executed in parallel.  In many cases,
	the callback code simply wrappers around kfree(), so that this
	is not an issue (or, more accurately, to the extent that it is
	an issue, the memory-allocator locking handles it).  However,
	if the callbacks do manipulate a shared data structure, they
	must use whatever locking or other synchronization is required
	to safely access and/or modify that data structure.

	Do not assume that RCU callbacks will be executed on the same
	CPU that executed the corresponding call_rcu() or call_srcu().
	For example, if a given CPU goes offline while having an RCU
	callback pending, then that RCU callback will execute on some
	surviving CPU.	(If this was not the case, a self-spawning RCU
	callback would prevent the victim CPU from ever going offline.)
	Furthermore, CPUs designated by rcu_nocbs= might well -always-
	have their RCU callbacks executed on some other CPUs, in fact,
	for some  real-time workloads, this is the whole point of using
	the rcu_nocbs= kernel boot parameter.

13.	Unlike other forms of RCU, it -is- permissible to block in an
	SRCU read-side critical section (demarked by srcu_read_lock()
	and srcu_read_unlock()), hence the "SRCU": "sleepable RCU".
	Please note that if you don't need to sleep in read-side critical
	sections, you should be using RCU rather than SRCU, because RCU
	is almost always faster and easier to use than is SRCU.

	Also unlike other forms of RCU, explicit initialization and
	cleanup is required either at build time via DEFINE_SRCU()
	or DEFINE_STATIC_SRCU() or at runtime via init_srcu_struct()
	and cleanup_srcu_struct().  These last two are passed a
	"struct srcu_struct" that defines the scope of a given
	SRCU domain.  Once initialized, the srcu_struct is passed
	to srcu_read_lock(), srcu_read_unlock() synchronize_srcu(),
	synchronize_srcu_expedited(), and call_srcu().	A given
	synchronize_srcu() waits only for SRCU read-side critical
	sections governed by srcu_read_lock() and srcu_read_unlock()
	calls that have been passed the same srcu_struct.  This property
	is what makes sleeping read-side critical sections tolerable --
	a given subsystem delays only its own updates, not those of other
	subsystems using SRCU.	Therefore, SRCU is less prone to OOM the
	system than RCU would be if RCU's read-side critical sections
	were permitted to sleep.

	The ability to sleep in read-side critical sections does not
	come for free.	First, corresponding srcu_read_lock() and
	srcu_read_unlock() calls must be passed the same srcu_struct.
	Second, grace-period-detection overhead is amortized only
	over those updates sharing a given srcu_struct, rather than
	being globally amortized as they are for other forms of RCU.
	Therefore, SRCU should be used in preference to rw_semaphore
	only in extremely read-intensive situations, or in situations
	requiring SRCU's read-side deadlock immunity or low read-side
	realtime latency.  You should also consider percpu_rw_semaphore
	when you need lightweight readers.

	SRCU's expedited primitive (synchronize_srcu_expedited())
	never sends IPIs to other CPUs, so it is easier on
	real-time workloads than is synchronize_rcu_expedited().

	Note that rcu_assign_pointer() relates to SRCU just as it does to
	other forms of RCU, but instead of rcu_dereference() you should
	use srcu_dereference() in order to avoid lockdep splats.

14.	The whole point of call_rcu(), synchronize_rcu(), and friends
	is to wait until all pre-existing readers have finished before
	carrying out some otherwise-destructive operation.  It is
	therefore critically important to -first- remove any path
	that readers can follow that could be affected by the
	destructive operation, and -only- -then- invoke call_rcu(),
	synchronize_rcu(), or friends.

	Because these primitives only wait for pre-existing readers, it
	is the caller's responsibility to guarantee that any subsequent
	readers will execute safely.

15.	The various RCU read-side primitives do -not- necessarily contain
	memory barriers.  You should therefore plan for the CPU
	and the compiler to freely reorder code into and out of RCU
	read-side critical sections.  It is the responsibility of the
	RCU update-side primitives to deal with this.

	For SRCU readers, you can use smp_mb__after_srcu_read_unlock()
	immediately after an srcu_read_unlock() to get a full barrier.

16.	Use CONFIG_PROVE_LOCKING, CONFIG_DEBUG_OBJECTS_RCU_HEAD, and the
	__rcu sparse checks to validate your RCU code.	These can help
	find problems as follows:

	CONFIG_PROVE_LOCKING: check that accesses to RCU-protected data
		structures are carried out under the proper RCU
		read-side critical section, while holding the right
		combination of locks, or whatever other conditions
		are appropriate.

	CONFIG_DEBUG_OBJECTS_RCU_HEAD: check that you don't pass the
		same object to call_rcu() (or friends) before an RCU
		grace period has elapsed since the last time that you
		passed that same object to call_rcu() (or friends).

	__rcu sparse checks: tag the pointer to the RCU-protected data
		structure with __rcu, and sparse will warn you if you
		access that pointer without the services of one of the
		variants of rcu_dereference().

	These debugging aids can help you find problems that are
	otherwise extremely difficult to spot.

17.	If you register a callback using call_rcu() or call_srcu(), and
	pass in a function defined within a loadable module, then it in
	necessary to wait for all pending callbacks to be invoked after
	the last invocation and before unloading that module.  Note that
	it is absolutely -not- sufficient to wait for a grace period!
	The current (say) synchronize_rcu() implementation is -not-
	guaranteed to wait for callbacks registered on other CPUs.
	Or even on the current CPU if that CPU recently went offline
	and came back online.

	You instead need to use one of the barrier functions:

	o	call_rcu() -> rcu_barrier()
	o	call_srcu() -> srcu_barrier()

	However, these barrier functions are absolutely -not- guaranteed
	to wait for a grace period.  In fact, if there are no call_rcu()
	callbacks waiting anywhere in the system, rcu_barrier() is within
	its rights to return immediately.

	So if you need to wait for both an RCU grace period and for
	all pre-existing call_rcu() callbacks, you will need to execute
	both rcu_barrier() and synchronize_rcu(), if necessary, using
	something like workqueues to to execute them concurrently.

	See rcubarrier.txt for more information.